EC Safety Data Sheet according to Directive 1907/2006 Trade name: Solder-wire KS 115 FLOWTIN ® TSC Date of issue: 15.12.2005 Revised on: 24.05.2011 Date of print: 08.11.2011 Page: 1(3) 1. Name of product, characterization and company name Information on the product Trade name: Usage of the product / preparation Solder-wire KS 115 FLOWTIN ® TSC Solder wire for soft soldering Identification of the manufacturer / supplier Address: MULTICOMP Premier Farnell plc 150 Armley Road LEEDS LS12 2QQ +44 (0) 870 129 8608 Phone: Fax: Emergency call: E-mail: +44 (0) 870 202530 (During office hours only) 2. Possible hazards: Not a composition for the purposes of the Dangerous Substances Regulations, but nevertheless observe items 4-16 3. Composition/Information on the components Chemical characterization: Tin-copper-silver alloy (with <0,1 % other iron-metals) with flux max. 3,5 % modified resin (halide-activated) Composition according to EC 1907/2006: Contents remainder 0,6-0,8% 3,6-4,0% <3,5% CAS No. 7440-31-5 7440-50-8 7440-22-4 EINECS No. 231-141-8 231-159-6 231-131-3 Symbols R-phrases: Substance Tin copper silver modified resin The wording of the R-phrases stated is indicated in Section 16 4. First Aid measures General information: After inhalation: After skin contact: After eye contact: After ingestion: Hints for doctors. If casualty is unconscious but breathing, place in the recovery position. If breathing has stopped apply artificial resuscitation or give oxygen by mask Remove patient to fresh air. If irritation resists, obtain medical attention. If any skin irritation develops seek medical attention Flush immediately with plenty of water. In cases where spitting flux has entered the eye seek medical attention. Rinse mouth immediately and drink plenty of water. Seek medical advice. Inhalation of the flux fumes given off at soldering temperatures will irritate the nose, throat and respiratory system. Repeated or prolonged exposure to flux fumes may cause shortness of breath and cough.. Physician's information Treatment: Decontamination, treatment of symptoms. 5. Fire fighting measures Suitable extinguishing media: Special protective equipment for fire fighting Use extinguishing media appropriate to surrounding fire conditions Wear self-contained breathing apparatus and protective clothing to prevent contact with skin and eyes. 6. Accidental release measures Pick up and place in appropriate container 7. Handling and storage The fumes produced during soldering should be extracted away from the breathing zone of the operators. Ensure the area is well ventilated. Wash hands with soap and warm water after handling, particularly before eating, drinking or smoking. The product should be stored in a cool, dry area. EC Safety Data Sheet according to Directive 1907/2006 Trade name: Solder-wire KS 115 FLOWTIN ® TSC Date of issue: 15.12.2005 Revised on: 24.05.2011 Date of print: 08.11.2011 Page: 2(3) 8. Exposure controls and personal protection Additional information on system design: Local exhaust or dilution ventilation and control of process conditions are suitable methods.. Substances with limit values to be monitored at the working place: Danger to health at the working place: Peak limit category: Working place limit values according to TRGS 900 from Section 2 for Germany: Product name CAS No. ml/m³ (ppm) mg/m³ Type Tin 7440-31-5 2 MAK (NL) Copper 7440-50-8 1 MAK (DFG) Silber 7440-22-4 0,1 MAK (DFG) Skin resorption / Sensitization: Skin resorption ---Sensitization: ----General protection and hygiene measures Avoid direct contact with eyes, the skin and clothing. Personal protection Respiratory protection: If concentrations are over the exposure limit, use a supplied air respirator. Hand protection: Use heat resistant gloves if required. Eye protection: Operators should wear goggles Personal protection: Light protective clothing 9. Physical and chemical properties Form: Melting Point: Vapour Pressure: Density(20°C): Form: Tin-Copper Solder Colour:silver 217°C n.a. 7-8 g/cm³ 10. Stability and reactivity Reaction with substances: Hazardous combustion or decomposition products: Possible with oxidising agents. none 11. Toxicological information The toxicological classification of the product is based on the results of the calculation procedure of the general preparation directive 1999/45/EC. Acute Effects: None toxic metal. 12. Ecological information General information: No effect to environment known 13. Disposal considerations Disposal information Product: Further information: Waste identity number: Contact a licensed professional waste disposal service to dispose of this material. Observe all federal, state and local environmental regulations. Collect metal for recycling Waste identity number EAK-code: 120104 14. Transport information GGVSEB/ADR The product is not classified as hazardous for transport EC Safety Data Sheet according to Directive 1907/2006 Trade name: Solder-wire KS 115 FLOWTIN ® TSC Date of issue: 15.12.2005 Revised on: 24.05.2011 Date of print: 08.11.2011 15. Legal regulations: Labelling information: Water hazard class: Classification according to the TA Luft: Ingredients: The product is classified and labelled according to the EC Directives. Not subject to current legislation WGK 1 (weakly water-endangering) Organic materials class III; whole-carbon-concentration: Max. acceptable Emission50 mg/m^3 (mass-flow-rate >= 0,5 kg/h) Tin, copper,silver, resin 16. Further information R-phrases point 3:-----------------------------n.k.: not known n.a.: not applicable Other information This statement is based on our current knowledge and offers no assurance of product properties. Page: 3(3)