Model CPCI32FF 32 Channel CPCI Board User Manual 0 1784 Chessie Lane, Ottawa, Illinois 61350 • Tel: 800/252-7074, 815/434-7800 • FAX:815/434-8176 e-mail: [email protected] • Web Address: http://www.freqdev.com Model CPCI32FF 32 Channel CPCI Board User Manual Sections 1.0 Introduction Page 1 2.0 Unpacking and Inspection 1 3.0 Hardware Configuration 1 4.0 Board Installation 5 5.0 I/O Connections and the Front Panel 5.1 Front Panel Layout 5.2 Input and Output Connector Configurations 5 5 7 6.0 Troubleshooting and Technical Support 8 7.0 Warranty Information 8 8.0 Repair 9 APPENDICES A. CPCI32FF Specifications 10 Figures 1. CPCI32FF Top View 2. Jumper Configuration 3. Block Diagram of a Typical Channel 4. Front Panel 3 4 4 6 We hope the information given here will be helpful. The information is based on data and our best knowledge, and we consider the information to be true and accurate. Please read all statements, recommendations or suggestions herein in conjunction with our conditions of sale, which apply, to all goods supplied by us. We assume no responsibility for the use of these statements, recommendations or suggestions, nor do we intend them as a recommendation for any use, which would infringe any patent or copyright. 1 1784 Chessie Lane, Ottawa, Illinois 61350 • Tel: 800/252-7074, 815/434-7800 • FAX:815/434-8176 e-mail: [email protected] • Web Address: http://www.freqdev.com Model CPCI32FF 32 Channel CPCI Board User Manual 1.0 - Introduction Each CPCI32FF provides 32-channels of fixed gain and fixed frequency filtering on a 6U, CompactPCI (CPCI) compatible board. Each CPCI32FF has optional single or differential inputs (DC coupled); and single or differential outputs (DC coupled). Frequency Devices provides a one (1) year product warranty from date of shipment for each card. See Appendix A for product performance specifications. 2.0 - Unpacking and Inspection Carefully inspect the exterior of the package for evidence of damage. After noting areas of possible shipping damage, open and unpack the shipping container, being careful to preserve the container and packing materials in case they are needed later. CAUTION CPCI32FF’s ARE SENSITIVE TO STATIC ELECTRICITY. USE PROPER GROUNDING TECHNIQUES WHEN HANDING THE BOARD. Carefully remove the CPCI32FF from its anti-static bag and visually inspect the card for evidence of damage. If the board appears to be damaged in any way, notify the shipping carrier. 3.0 - Hardware Configuration Once the CPCI32FF has been removed from its anti-static bag and inspected for damage, you are ready to configure the board. CAUTION CPCI32FF’s ARE SENSITIVE TO STATIC ELECTRICITY. USE PROPER GROUNDING TECHNIQUES WHEN HANDING THE BOARD. Lay the CPCI32FF on a static protected flat surface as shown in Figure 1. 2 1784 Chessie Lane, Ottawa, Illinois 61350 • Tel: 800/252-7074, 815/434-7800 • FAX:815/434-8176 e-mail: [email protected] • Web Address: http://www.freqdev.com Model CPCI32FF 32 Channel CPCI Board User Manual 15 31 14 30 13 29 12 28 11 27 10 26 9 25 8 24 7 23 6 22 5 21 4 20 3 19 2 18 1 17 0 16 See Figure 2 for J1 Jumper detail Figure 1 CPCI32FF Top View 3 1784 Chessie Lane, Ottawa, Illinois 61350 • Tel: 800/252-7074, 815/434-7800 • FAX:815/434-8176 e-mail: [email protected] • Web Address: http://www.freqdev.com Model CPCI32FF 32 Channel CPCI Board User Manual The only user configuration on the CPCI32FF is Jumper J1 (Figure 2), to select the ground reference to the analog circuitry. Jumper J1 allows the analog common of the channel path to float, be referenced to the front panel chassis ground, or be connected to the CPCI back plane power supply return. The best noise performance is obtained by jumpering the Analog Common with the CPCI back plane return. NC CHASSIS GND ANALOG COMMON J1 Jumper Detail from Figure 1 Default J1 jumper configuration CPCI BP RETURN Figure 2 J1 Jumper Configuration After the J1 jumper has been configured, the CPCI32FF is ready for installation in a CPCI system. Figure 3 identifies a typical channel for single ended input and differential output configuration. Typical 16 CHANNEL DAC card FREQUENCY DEVICES 32 CHANNEL CPCI SIG. COND. CARD INA111 3 Amplifier differential gain block DAC Analog Filter D74L4B Differential Analog output + Hi + Hi - Lo - Lo BUFFERS, ETC. OUTPUT RETURN A or B OUT_RTN_A = Even OUT_RTN_B= Odd DAC Board GROUND SENSE CPCI32FF ANALOG COMMON CHASSIS GROUND Hi + + _ _ + _ Lo GAIN SET + INA111 Burr Brown Detail CPCI BP GROUND Either of these two grounds can be connected to analog common on the card via a jumper, J1. Default is CPCI BP Ground for lowest noise. Figure 3 Block Diagram of a Typical Channel 4 1784 Chessie Lane, Ottawa, Illinois 61350 • Tel: 800/252-7074, 815/434-7800 • FAX:815/434-8176 e-mail: [email protected] • Web Address: http://www.freqdev.com Model CPCI32FF 32 Channel CPCI Board User Manual 4.0 - Board Installation CAUTION CPCI32FF’s ARE SENSITIVE TO STATIC ELECTRICITY. USE PROPER GROUNDING TECHNIQUES WHEN HANDING THE BOARD. Frequency Devices' Model CPCI32FF mechanically conforms to the single width 6U CPCI form factor. The CPCI32FF may be installed in any available CPCI slot except Slot 0. The board does not use CPCI interrupts or bus mastering capabilities. A major consideration when selecting a slot location for the CPCI32FF will be the EMI and I/O signal cabling. To minimize interference from other boards in the system, it is good practice to keep one or more empty slots between analog signal conditioning boards and high-speed digital boards. When cabling the system, it is desirable to keep the analog signal cable as short as possible and physically located away from high speed digital cables and high voltage switching lines. 5.0 - I/O Connections and the Front Panel The following information is provided to assist the user when installing a CPCI32FF into a CPCI system. 5.1 - Front Panel Layout The following sections provide detailed information about connectors, pin-out, and cabling. There are no front panel indicators or controls on the CPCI32FF. Figure 4 shows the layout of the front panel. 5 1784 Chessie Lane, Ottawa, Illinois 61350 • Tel: 800/252-7074, 815/434-7800 • FAX:815/434-8176 e-mail: [email protected] • Web Address: http://www.freqdev.com Model CPCI32FF 32 Channel CPCI Board User Manual CPCI32FF 39 59 20 78 78 pin female 60 1 40 21 INPUT 40 OUTPUT 21 1 60 78 pin male 78 20 59 39 Figure 4 CPCI32FF Front Panel 6 1784 Chessie Lane, Ottawa, Illinois 61350 • Tel: 800/252-7074, 815/434-7800 • FAX:815/434-8176 e-mail: [email protected] • Web Address: http://www.freqdev.com Model CPCI32FF 32 Channel CPCI Board User Manual 5.2. - Input and Output Connector Configurations The input connector on the board is a female 78 pin high-density D-sub connector. The output connector is a male 78 pin high-density D-sub connector. Input and output connectors have the same pin out. Known suppliers for a mating connector are Edac of Canada (633, 634 series), Positronic (ODD series), and AMP. An exact mating connector cannot be recommended because of the large variety of usable connector configuration details such as hoods, cable exit options, etc. The pins identified Low on the input and output connectors, are tied to the analog common when the single ended input or output option is selected. CH # Channel 0 High Channel 0 Low Channel 1 High Channel 1 Low Channel 2 High Channel 2 Low Channel 3 High Channel 3 Low Channel 4 High Channel 4 Low Channel 5 High Channel 5 Low Channel 6 High Channel 6 Low Channel 7 High Channel 7 Low Channel 8 High Channel 8 Low Channel 9 High Channel 9 Low Channel 10 High Channel 10 Low Channel 11 High Channel 11 Low Channel 12 High Channel 12 Low Channel 13 High Channel 13 Low Channel 14 High Channel 14 Low Channel 15 High Channel 15 Low CH # Channel 16 High Channel 16 Low Channel 17 High Channel 17 Low Channel 18 High Channel 18 Low Channel 19 High Channel 19 Low Channel 20 High Channel 20 Low Channel 21 High Channel 21 Low Channel 22 High Channel 22 Low Channel 23 High Channel 23 Low Channel 24 High Channel 24 Low Channel 25 High Channel 25 Low Channel 26 High Channel 26 Low Channel 27 High Channel 27 Low Channel 28 High Channel 28 Low Channel 29 High Channel 29 Low Channel 30 High Channel 30 Low Channel 31 High Channel 31 Low PIN# 69 70 50 51 31 32 11 12 71 72 52 53 33 34 13 14 73 74 54 55 35 36 15 16 75 76 56 57 37 38 17 18 PIN# 61 62 42 43 23 24 3 4 63 64 44 45 25 26 5 6 65 66 46 47 27 28 7 8 67 68 48 49 29 30 9 10 Pins always available for shielding: 1, 2, 19, 20, 21, 22, 39, 40, 41, 58, 59, 60, 77 & 78. 7 1784 Chessie Lane, Ottawa, Illinois 61350 • Tel: 800/252-7074, 815/434-7800 • FAX:815/434-8176 e-mail: [email protected] • Web Address: http://www.freqdev.com Model CPCI32FF 32 Channel CPCI Board User Manual 6.0 - Troubleshooting and Technical Support If you have difficulty installing the CPCI32FF, or if the board fails to operate properly, contact Frequency Devices for technical assistance. Technical assistance is available weekdays 8:00 AM to 5:00 PM Eastern time at: Email: [email protected] Telephone: 1-815-434-7800 or at 1-800-252-7074 (US only) Fax: 1-815-434-8176. If you would like to contact Frequency Devices in writing, our mailing address is: Attn: Customer Service 1784 Chessie Lane Ottawa, IL 61350 7.0 – Warranty Information The CPCI32FF is warranted against defects in material and workmanship for a period of one (1) year from the date of shipment. During the warranty period, Frequency Devices, Inc. will, at its option, repair or replace products that prove to be defective. For warranty service or repair: • Customer must provide a detailed description of the problem. • Obtain a Return Authorization (RA) number from the factory. • Properly package and return the product to Frequency Devices. Limited Warranty This warranty shall not apply to defects that are the result of improper use, unauthorized modification or repair, or improper installation or maintenance. No other warranty is expressed or implied. Frequency Devices, Inc. specifically disclaims the implied warranties of merchantability and fitness for a particular purpose. The remedies provided herein are the Buyer’s sole and exclusive remedies. Frequency Devices, Inc. shall not be liable for any direct, indirect, special, incidental, or consequential damages, whether based on contact, tort, or any other legal history. Certification Frequency Devices, Inc. certifies that this product met its published specification at the time of shipment from our factory. Frequency Devices, Inc. further certifies that its calibration measurements are traceable to the United States National Bureau of Standards, to the extent allowed by the bureau’s calibration facility. 8 1784 Chessie Lane, Ottawa, Illinois 61350 • Tel: 800/252-7074, 815/434-7800 • FAX:815/434-8176 e-mail: [email protected] • Web Address: http://www.freqdev.com Model CPCI32FF 32 Channel CPCI Board User Manual 8.0 - Repair Frequency Devices, Inc. maintains a repair facility at its factory in Ottawa, Illinois that is available for both in-warranty and non-warranty repairs. We suggest that you contact Frequency Devices at [email protected] for a Return Authorization (RA) number before taking steps to return equipment for repair. Return Authorization All products being returned to Frequency Devices, Inc. must have a Return Authorization (RA) number. You may obtain an RA number by calling Frequency Devices, Inc. at Tel.: 815/434-7800 or emailing [email protected] before returning the product. The RA number should be clearly displayed on the outside of the package being returned and should be placed on all correspondence concerning the instrument. Frequency Devices, Inc. may refuse to accept shipment and will not be responsible for shipping charges of product returned without an RA number. 9 1784 Chessie Lane, Ottawa, Illinois 61350 • Tel: 800/252-7074, 815/434-7800 • FAX:815/434-8176 e-mail: [email protected] • Web Address: http://www.freqdev.com Model CPCI32FF Specifications (Typical @ 25oC and rated Power Input) APPENDIX A Analog Input 1. Impedance 2. Input Range 3. Maximum Input 4. Common Mode Rejection 1 GΩ / 47pF ±10V pk. linear ±40V 75 dB min. @ 60 Hz. Analog Output (each leg) 5. Impedance 6. Linear Operating Range 7. Channel to Channel Crosstalk 8. Maximum Current 9. Offset Voltage 10. Offset Temp. Coeff. 11. Short Circuit Protection 12. Peak Distortion @ 1 kHz, 3.54 Vrms 1.0 Ω typ., 10 Ω max. ±10V pk. <-80 dB max. @ 10 kHz ±5mA ±5mV max. 20µV/°C Short to Ground -80 dBc max. Filter Characteristics 13. See D72 or D74 Series specifications 14. Fixed Cut-off Frequency fc (-3dB) Available 1 Hz to 100 kHz - Factory set Gain 15. Nominal Gain 16. Accuracy 1X, 10X, 100X, 1000X – Factory set ±1% Power Supply 17. From CPCI Backplane 18. Isolation (default) +12 V and -12 V, ± 5%, 1.0 A max. each Analog ground isolated from backplane and chassis. Connection to ground / backplane common by jumper, can be changed by customer or factory specified. 0°C to +70°C -25°C to +85°C 0-95% non-condensing Environmental 19. Operating 20. Storage 21. Humidity Mechanical 22. Card Size 23. No. of Input Channels 24. No. of Output Channels 25. Mating Connectors CPCI 6U single slot 9.17 x 6.3 inches, (233 x160 mm) 32 Single or differential, DC coupled, factory set. 32 Single or differential, DC coupled, factory set. Input: Female high-density 78-pin D-sub Output: Male high-density 78-pin D-sub ~2 lbs., (0.91 kg.) 26. Weight Ordering Information Gain Options 1X, 10X, 100X, 1000X CPCI32FF-S32D-10X Input S – Single Ended D – Differential Output S – Single Ended D – Differential We hope the information given here will be helpful. The information is based on data and our best knowledge, and we consider the information to be true and accurate. Please read all statements, recommendations or suggestions herein in conjunction with our conditions of sale, which apply, to all goods supplied by us. We assume no responsibility for the use of these statements, recommendations or suggestions, nor do we intend them as a recommendation for any use, which would infringe any patent or copyright. 10 1784 Chessie Lane, Ottawa, Illinois 61350 • Tel: 800/252-7074, 815/434-7800 • FAX:815/434-8176 e-mail: [email protected] • Web Address: http://www.freqdev.com