HS-1743 Intel® Core™ 2 Duo/Core™ Duo/ Core™ Solo/Celeron® M processor Mini ITX Board •CompactFlash•Mini PCI•PCIe x1•PCI• •GPIO•DVI-I/CRT/LVDS•Dual GB LAN• •Audio•SATA•RS-232/422/485•8 COM• •8 USB2.0•WDT•H/W Monitor• Copyright Disclaimers The accuracy of contents in this manual has passed thorough checking and review before publishing. BOSER Technology Co., Ltd., the manufacturer and publisher, is not liable for any infringements of patents or other rights resulting from its use. The manufacturer will not be responsible for any direct, indirect, special, incidental or consequential damages arising from the use of this product or documentation, even if advised of the possibility of such damage(s). This manual is copyrighted and BOSER Technology Co., Ltd. reserves all documentation rights. Unauthorized reproduction, transmission, translation, and storage of any form and means (i.e., electronic, mechanical, photocopying, recording) of this document, in whole or partly, is prohibited, unless granted permission by BOSER Technology Co., Ltd. BOSER Technology Co., Ltd. reserves the right to change or improve the contents of this document without due notice. BOSER Technology Co., Ltd. assumes no responsibility for any errors or omissions that may appear in this manual, nor does it make any commitment to update the information contained herein. TTrraaddeem maarrkkss BOSER is a registered trademark of BOSER Technology Co., Ltd. ISB is a registered trademark of BOSER Technology Co., Ltd. Intel is a registered trademark of Intel Corporation. Award is a registered trademark of Award Software, Inc. AMI is a registered trademark of AMI Software, Inc. All other trademarks, products and or product names mentioned herein are mentioned for identification purposes only, and may be trademarks and/or registered trademarks of their respective companies or owners. © Copyright 2010 BOSER Technology Co., Ltd. All Rights Reserved. Edition 1.1, November 02, 2010 Table of Contents Chapter 1 General Description ..................................1 1.1 Major Features ....................................................................... 2 1.2 Specifications ........................................................................ 2 1.3 Board Dimensions................................................................. 4 Chapter 2 Unpacking ..................................................5 2.1 Opening the Delivery Package............................................. 5 2.2 Inspection............................................................................... 5 Chapter 3 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14 3.15 3.16 3.17 3.18 3.19 3.20 3.21 Hardware Installation ..............................7 Before Installation ................................................................. 7 Board Layout ......................................................................... 8 Jumper List ............................................................................ 9 Connector List ..................................................................... 10 Configuring the CPU ........................................................... 10 System Memory ................................................................... 10 VGA Controller .................................................................... 11 Serial ATA Connector ......................................................... 13 Parallel Connector............................................................... 13 Serial Port Connectors ....................................................... 14 Ethernet Connector............................................................. 16 USB Connector.................................................................... 17 CMOS Data Clear................................................................. 17 Power and Fan Connectors................................................ 18 Keyboard/Mouse Connectors ............................................ 19 System Front Panel Control ............................................... 20 Watchdog Timer .................................................................. 21 Audio Connectors ............................................................... 22 CompactFlash Socket ...................................................... 23 Expansion Interface ............................................................ 24 8-bit GPIO Function............................................................. 25 Chapter 4 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 Chapter 5 5.1 5.2 5.3 5.4 AMI BIOS Setup ..................................... 27 Starting Setup...................................................................... 27 Using Setup ......................................................................... 28 Main Menu............................................................................ 29 Advanced Settings .............................................................. 30 Advanced PCI/PnP Settings............................................... 35 Boot Settings ....................................................................... 36 Security Settings ................................................................. 36 Advanced Chipset Settings................................................ 37 Exit Options ......................................................................... 38 Software Utilities..................................... 39 Chipset Driver Installation.................................................. 39 VGA Driver Installation ....................................................... 42 Audio Driver Installation..................................................... 45 LAN Driver Installation........................................................ 48 Declaration of Conformity -- CE Mark BOSER Technology hereby acknowledges that compliance testing in accordance with applicable standards of the EU’s EMC Directive, 89/336/EEC, was successfully completed on a sample of the equipment identified below: Equipment Class: Product Model Series: This Product Complies With: Information Technology Equipment HS-1743 EN55022: Class A for Radiated emissions EN50082-2: Heavy Industrial EMC Immunity We, the undersigned, hereby declare that the equipment specified above conforms to the above directives and standards. Manufacturer: BOSER TECHNOLOGY CO., LTD. Safety Instructions Integrated circuits on computer boards are sensitive to static electricity. To avoid damaging chips from electrostatic discharge, observe the following precautions: Do not remove boards or integrated circuits from their anti-static packaging until you are ready to install them. Before handling a board or integrated circuit, touch an unpainted portion of the system unit chassis for a few seconds. This helps to discharge any static electricity on your body. Wear a wrist-grounding strap, available from most electronic component stores, when handling boards and components. Fasten the ALLIGATOR clip of the strap to the end of the shielded wire lead from a grounded object. Please wear and connect the strap before handle the product to ensure harmlessly discharge any static electricity through the strap. Please use an anti-static pad when putting down any components or parts or tools outside the computer. You may also use an anti-static bag instead of the pad. Please inquire from your local supplier for additional assistance in finding the necessary anti-static gadgets. NOTE: DO NOT TOUCH THE BOARD OR ANY OTHER SENSITIVE COMPONENTS WITHOUT ALL NECESSARY ANTI-STATIC PROTECTIONS. Chapter 1 General Description The HS-1743 is an Intel® 945GME GMCH chipset-based board designed. The HS-1743 is an ideal all-in-one mini ITX board. Additional features include an enhanced I/O with CF, DVI-I/CRT/LVDS, dual GB LAN, audio, SATA, COM, and USB2.0 interfaces. Designed with the Intel® 945GME GMCH, the board supports Socket M for Intel® Core™ 2 Duo/Core™ Duo/Core™ Solo/Celeron® M 400 series processor. The Intel® ICH7-M serial ATA controller with two ports supporting transfer rates up to 150MB/sec. 1 Onboard Intel® 945GME GMCH for CRT display with DVMT or option CHRONTEL 7307 for DVI-I display supporting up to 2048 x 1536. It also supports 18-bit single/dual channel LVDS interface. System memory is also sufficient with the one SO-DDR2 socket that can support up to 2GB. Additional onboard connectors include eight USB2.0 ports providing faster data transmission. And two external RJ-45 connectors for 10/100/1000 Based Ethernet uses. To secure the reliability in the unmanned or standalone system, the function of WDT (Watchdog Timer) in HS-1743 can be combined with the software which does not need arithmetical functions of a real-time clock chip. The WDT function can automatically reboot the system once programs crash in the system. 1.1 Major Features The HS-1743 comes with the following features: ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ 1.2 Socket M for Intel® Core™ 2 Duo/Core™ Duo/Core™ Solo/Celeron® M 400 series processor, supports 667/533MHz FSB 1 x SO-DIMM up to 2GB DDR2 SDRAM Intel® 945GME/ICH7-M system chipset Intel® 945GME integrated VGA for DVI-I, CRT & LVDS 2 x Intel® 10/100/1000 Mbps ethernet AC’97 audio codec Provides 2W stereo power amplifier Supports CF, 1 x PCIe x1, 1 x mini PCI, 1 x PCI, 2 x SATA, 8 x COM, 8 x USB2.0 Supports 18-bit LVDS, 8-bit GPIO, H/W Monitor function Specifications z System 2 CPU: Intel® Core™ 2 Duo/Core™ Duo/Core™ Solo/Celeron® M 400 series processor Front Side Bus: 667/533MHz FSB BIOS: AMI PnP Flash BIOS System Chipset: Intel® 945GME/ICH7-M I/O Chipset: Winbond W83627EHG System Memory: 1 x 200-pin SO-DIMM socket DDR2 667MHz up to 2GB Storage: 1 x Type II CF socket Watchdog Timer: Software programmable time-out intervals from 1~255 sec. or 1~255 min. H/W Status Monitor: Monitoring temperatures, voltages, and cooling fan status Expansion Interface: 1 x Type III mini PCI socket 1 x PCIe x1 socket (solder side) 1 x Non-standard PCI socket (solder side) for BOSER Riser Card Power Function: Supports AT/ATX power mode Operating Temperature: 0~60 degrees C Operating Humidity 0~95%, non-condensing Size(L x W): 170 x 170 mm z I/O Interface MIO: 7 x RS-232 (2 x external, 5 x internal, COM 3/COM 4 support +5V or +12V/1A power output) 1 x RS-232/422/485 8 x USB2.0 (4 x internal, 4 x external) 1 x Parallel 2 x SATA 1 x PS/2 Mini DIN for KB 1 x PS/2 Mini DIN for MS GPIO: 8-bit general purpose input/output port z Display Chipset: Intel® 945GME integrated Intel® GMA950 Display Memory: 224MB video memory with DVMT3.0 LVDS: 18-bit single/dual-channel 3 Resolution: 2048 x 1536 DVI Chipset: Chrontel 7307 z Audio Chipset: RealTek ALC202A Audio Interface (w/audio jack): MIC In, Line Out Amplifier: Provides 2W stereo power amplifier z Ethernet 1.3 4 Chipset: Dual RTL8111C 10/100/1000 Mbps LAN Ethernet Interface: 2 x RS-45 Board Dimensions Chapter 2 Unpacking 2.1 Opening the Delivery Package The HS-1743 is packed in an anti-static bag. The board has components that are easily damaged by static electricity. Do not remove the anti-static wrapping until proper precautions have been taken. Safety Instructions in front of this manual describe anti-static precautions and procedures. 2.2 Inspection After unpacking the board, place it on a raised surface and carefully inspect the board for any damage that might have occurred during shipment. Ground the board and exercise extreme care to prevent damage to the board from static electricity. Integrated circuits will sometimes come out of their sockets during shipment. Examine all integrated circuits, particularly the BIOS, processor, memory modules, ROM-Disk, and keyboard controller chip to ensure that they are firmly seated. The HS-1743 delivery package contains the following items: HS-1743 Board x 1 Utility CD Disk x 1, including User’s Manual Cables (as following table) Jumper Bag x 1 5 Cables Package Description NO. 1 2 3 4 Print DB25-26P(2.0) flat cable 27cm SATA cable 50cm (w/Lock) COM DB9*4-40P(2.0) flat cable 22cm SATA power cable 15cm QTY. 1 1 1 1 It is recommended that you keep all the parts of the delivery package intact and store them in a safe/dry place for any unforeseen event requiring the return shipment of the product. In case you discover any missing and/or damaged items from the list of items, please contact your dealer immediately. Option Accessories NO. Description 1 2 3 4 5 6 SATA power cable SATA cable 50cm (w/Lock) 2RS232(2.0) flat cable USB 1-to 2 cable 20cm H=23mm CPU Cooler Chapter 3 Hardware Installation This chapter provides the information on how to install the hardware using the HS-1743. This chapter also contains information related to jumper settings of switch, and watchdog timer selection etc. 3.1 Before Installation After confirming your package contents, you are now ready to install your hardware. The following are important reminders and steps to take before you begin with your installation process. 1. Make sure that all jumper settings match their default settings and CMOS setup correctly. Refer to the sections on this chapter for the default settings of each jumper. (Set JP8 open) 2. Go through the connections of all external devices and make sure that they are installed properly and configured correctly within the CMOS setup. Refer to the sections on this chapter for the detailed information on the connectors. 3. Keep the driver CD in good condition for future reference and use. 7 3.2 Board Layout Top Side 8 Solder Side 3.3 Jumper List Jumper Default Setting JP1 JP2/JP7 JP3 JP4 JP5 JP6 JP8 CN4/CN6 CF Use Master/Slave Select: Master AT/ATX Power Mode Select: ATX Panel Voltage Select: +3.3V FSB Frequency Select: 667MHz Inverter Voltage Select: +5V LAN1 Enabled/Disabled Select: Enabled Clear CMOS: Normal Operation COM 3/COM 4 Power Pin Select: Normal COM 2 Use RS-232 or RS-422/485 Select: RS-232 CN18 Setting Page Short 1-2 Open Short 2-3 Open Short 2-3 Open Open Short 3-4 23 18 11 10 11 16 17 14 Open 14 9 3.4 Connector List Connector CN1 CN2 CN3 CN5 CN7 CN8 CN9 CN10/CN13 CN11/CN12 CN14/CN17 CN15 CN16 CN19 CN20 CN21 CN22/CN23 CN24 CN25/CN26 CN27 CN28 DDR1 PCI1 FN1/FN2 PW1 3.5 Definition Page Internal 6-pin KB/MS Connector PS/2 6-pin Mini DIN KB & MS Connector 15-pin CRT/DVI-I Connector COM 5 ~ COM 8 Connector (2x20 Header) COM 1/COM 2 Connector (DB9) COM 3/COM 4 Connector (2x10 Header) Inverter Power Connector LVDS Panel Connector Internal USB2.0 Ports RJ-45 + External USB2.0 Port Parallel Port System Front Panel Connector/LAN LED RS-485 Connector (3x2 Header) MIC In/Line Out Connector 8-bit GPIO Serial ATA Connector Mini PCI Socket Stereo Speaker Amplifier PCIe x1 Socket CompactFlash Socket DDR2 Socket PCI Socket Fan Power Connector 20-pin ATX Power Connector 19 19 11 14 14 14 11 11 17 16/17 13 20 14 22 25 13 24 22 24 23 10 24 18 18 Configuring the CPU The HS-1743 provides with Socket M for Intel® Core™ 2 Duo/ Core™ Duo/Core™ Solo/Celeron® M 400 series processor. z 3.6 JP4: FSB Frequency Select Options Settings 533MHz FSB 667MHz FSB (default) Short Open 2 1 System Memory The HS-1743 provides one SO-DDR2 socket at locations DDR1. The maximum capacity of the onboard memory is 2GB. 10 3.7 VGA Controller The HS-1743 provides three types of connection for video output. CN3 offers a CRT/DVI-I connector and CN10/CN13 are the LVDS interface connectors onboard reserved for flat panel installation. z CN3A: 15-pin CRT Connector PIN Description PIN Description 1 3 5 7 9 11 13 15 Red Blue GND GND VCC N/C HSYNC SCL 2 4 6 8 10 12 14 Green N/C X GND GND SDA VSYNC 1 6 11 5 10 15 z CN10/CN13: LVDS Interface Connector PIN Description PIN Description 1 3 5 7 9 11 13 VLCD GND Y0-/Z0Y1-/Z1Y2-/Z2CLKN/C 2 4 6 8 10 12 14 VLCD GND Y0+/Z0+ Y1+/Z1+ Y2+/Z2+ CLK+ N/C 1 13 2 14 NOTE: LVDS cable should be produced very carefully. Y0- & Y0+ have to be fabricated in twister pair (Y1- & Y1+, Y2- & Y2+ and so on) otherwise the signal won’t be stable. Please set the proper voltage of your panel using JP3 before proceeding on installing it. NOTE: If use CN10 only, it just supports 18-bit single channel LVDS panel; If want to use 18-bit dual channel LVDS panel, please use CN10 and CN13 combined. 11 The HS-1743 has an onboard jumper that selects the working voltage of the flat panel connected to the system. Jumper JP3 offers two voltage settings for the user. z JP3: Panel Voltage Select Options Settings 1 +5V +3.3V (default) Short 1-2 Short 2-3 3 z CN9: Inverter Power Connector PIN Description 1 2 3 4 5 6 +12V +12V +5V BK_EN LCD_EN GND 1 6 z JP5: Inverter Voltage Select Options Settings 1 +3.3V +5V (default) Short 1-2 Short 2-3 3 z CN3B: DVI-I Connector PIN Description PIN Description 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 12 - DATA2 GND DATA4 DDCDATA -DATA1 GND DATA3 GND -DATA0 GND DATA5 CLK RED BLUE GND 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 DATA2 -DATA4 DDCCLK VSYNC DATA1 -DATA3 VCC5 HPDET DATA0 -DATA5 GND -CLK GREEN HSYNC GND 3.8 Serial ATA Connector You can connect the Serial ATA device that provides you high speeds transfer rates (150MB/sec.). z CN22/CN23: Serial ATA Connector 3.9 PIN Description 1 2 3 4 5 6 7 GND SATATXP SATATXN GND SATARXN SATARXP GND 1 7 Parallel Connector CN15 is a standard 26-pin flat cable connector designed to accommodate parallel port connection on the HS-1743. z CN15: Parallel Port PIN Description PIN Description 1 2 3 4 5 6 7 8 9 10 11 12 13 Strobe DATA 0 DATA 1 DATA 2 DATA 3 DATA 4 DATA 5 DATA 6 DATA 7 Acknowledge Busy Paper Empty Printer Select 14 15 16 17 18 19 20 21 22 23 24 25 26 Auto Form Feed ERROR# Initialize Printer Select LN# GND GND GND GND GND GND GND GND GND 14 26 1 13 13 3.10 Serial Port Connectors The HS-1743 offers 16C550 compatible UARTs with Send/ Receive 16-byte FIFO serial ports and six internal 10-pin headers for RS-232 and two RS-422/485 connectors. z CN7: COM 1/COM 2 Connector (DB9) PIN Description PIN Description 1 2 3 4 5 6 7 8 9 z DCD2 RXD2 TXD2 DTR2 GND DSR2 RTS2 CTS2 RI2 10 11 12 13 14 15 16 17 18 DCD1 RXD1 TXD1 DTR1 GND DSR1 RTS1 CTS1 RI1 CN8: COM 3/COM 4 Connector (2x10 Header) PIN Description PIN Description 1 3 5 7 9 11 13 15 17 19 14 DCD3 RXD3 TXD3 DTR3 GND DCD4 RXD4 TXD4 DTR4 GND 2 4 6 8 10 12 14 16 18 20 DSR3 RTS3 CTS3 RI3 N/C DSR4 RTS4 CTS4 RI4 N/C 2 20 1 19 z CN5: COM 5~COM 8 Connector (2x20 Header) PIN Description PIN Description 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 z DCD RXD TXD DTR GND DCD RXD TXD DTR GND DCD RXD TXD DTR GND DCD RXD TXD DTR GND 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 DSR RTS CTS RI N/C DSR RTS CTS RI N/C DSR RTS CTS RI N/C DSR RTS CTS RI N/C 2 40 1 39 CN19: RS-422/485 Connector (3x2 Header) PIN Description PIN Description 1 3 5 z TXRX+ GND 2 4 6 TX+ RXVCC 5 1 6 2 CN4/CN6: COM 3/COM 4 Power Pin Select Options RI (default) +5V +12V Settings CN4 CN6 Short 3-4 Short 5-6 Short 1-2 Short 3-4 Short 5-6 Short 1-2 2 6 2 6 1 5 1 5 15 z CN18: COM 2 use RS-232 or RS-422/485 Select Options Settings RS-232 (default) RS-485 Transmit Only RS-485 by –RTS (*-1) RS-422/485 Full Duplex (*2) Open Short 1-2, 3-4, 5-7, 8-10 Short 1-2, 3-4, 7-9, 8-10 Short 1-2, 3-4, 6-8 NOTE: 9 1 10 2 *1: 2-wires RS-485 function *2: 4-wires point-to-point full duplex function 4-wires point-to-point full duplex RS-422/485 Typical RS-485 2-wires Mutildrop Network 3.11 Ethernet Connector The HS-1743 provides two external RJ-45 interface connectors. Please refer to the following for its pin information. z CN14A/CN17A: RJ-45 Connector PIN Description 1 2 3 4 5 6 7 8 16 TX+ TXRX+ R/C GND R/C GND RXR/C GND R/C GND 8 1 z JP6: LAN 1 Enabled/Disabled Select Options Settings Disabled Enabled (default) Short Open 1 2 3.12 USB Connector The HS-1743 provides two 8-pin connectors, at location CN11/CN12, for four USB2.0 ports, and four external USB2.0 port at CN14B/CN17B. z CN14B/CN17B: External USB2.0 Port PIN Description PIN Description 1 3 5 7 VCC USBD0-/USB2USBD0+/USB2+ GND 2 4 6 8 VCC USBD1-/USB3USBD1+/USB3+ GND z CN11/CN12: Internal USB2.0 Ports PIN Description PIN Description 1 3 5 7 VCC USBD4-/USB6USBD4+/USB6+ GND 2 4 6 8 VCC USBD5-/USB7USBD5+/USB7+ GND 2 8 1 7 3.13 CMOS Data Clear The HS-1743 has a Clear CMOS jumper on JP8. z JP8: Clear CMOS Options Settings Normal Operation (default) Clear CMOS Open Short 1 2 IMPORTANT: Before turn on the power of your system, please set JP8 to open for normal operation. 17 3.14 Power and Fan Connectors z PW1: 20-pin ATX Power Connector PIN Description PIN Description 1 2 3 4 5 6 7 8 9 10 z +3.3V +3.3V GND +5V GND +5V GND Power OK 5VSB +12V 11 12 13 14 15 16 17 18 19 20 +3.3V -12V GND PS_ON GND GND GND N/C +5V +5V 10 1 20 11 JP2/JP7: AT/ATX Power Function Select Options ATX (default) AT Settings JP2 JP7 Open Short Open Short 1 2 1 2 z 18 FN1/FN2: Fan Power Connector PIN Description 1 2 3 GND +12V Fan In 1/Fan In 2 1 3 3.15 Keyboard/Mouse Connectors The HS-1743 offers two possibilities for keyboard/mouse connections. The connection is via CN1 for an internal 6-pin cable converter to a keyboard/mouse. z CN1: Internal 6-pin KB/MS Connector z z PIN Description 1 2 3 4 5 6 Keyboard Data Mouse Data GND +5V Keyboard Clock Mouse Clock 6 1 CN2A: PS/2 6-pin Mini DIN Keyboard Connector PIN Description 1 2 3 4 5 6 Keyboard Data N/C GND +5V Keyboard Clock N/C 6 4 2 5 3 1 CN2B: PS/2 6-pin Mini DIN Mouse Connector PIN Description 1 2 3 4 5 6 Mouse Data N/C GND +5V Mouse Clock N/C 6 4 2 5 3 1 19 3.16 System Front Panel Control The HS-1743 has front panel control at location CN16 that indicates power-on, HDD and LAN action status. z CN16: System Front Panel Control PIN Description PIN Description 1 3 5 7 9 11 13 15 17 19 330Ω pull VCC HDD LED ATX Power Button VCC Reset Switch GND -Link_100_LED0 -Link_1G_LED0 -Link_100_LED1 -Link_1G_LED1 2 4 6 8 10 12 14 16 18 20 Speaker N/C VCC 330Ω pull VCC 330Ω pull 3.3V Power LED 3V_Dual Link/Act_LED0 3V_Dual Link/Act_LED1 Connector CN16 Orientation HDD LED ATX Power Button Reset Button 20 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Speaker PWR LED 3.17 Watchdog Timer A user can set a value of Watchdog Timer in his software to reboot their hardware system. It is forced to reboot once user’s software fails to reset the Watchdog Timer before the counter of Watchdog Timer meets user’s setting value. This function, Watchdog Timer, prevents user’s software from crashing. W83627EHG WDT Assembly sample code: -----------------------------------Extended function mode -----------------------------------MOV DX,2EH MOV AL,87H OUT DX,AL OUT DX,AL ------------------------------------Configure logical device 8 ------------------------------------MOV DX,2EH MOV AL,07H OUT DX,AL MOV DX,2FH MOV AL,08H OUT DX,AL MOV DX,2EH MOV AL,30H ; Enable WDT OUT DX,AL MOV DX,2FH MOV AL,01H OUT DX,AL -------------------------------------Configure time mode -------------------------------------MOV DX,2EH MOV AL,F5H OUT DX,AL MOV DX,2FH MOV AL,00H ; Setup second mode, 08H for minute mode 21 OUT DX,AL --------------------------------------Configure reset time interval --------------------------------------MOV DX,2EH MOV AL,F6H OUT DX,AL MOV DX,2FH MOV AL,05H ; Setup reset time 5, User can setup from 1~255 OUT DX,AL Once the Enable cycle is active a Refresh cycle is requested before the time-out period of watchdog timer. The refresh cycle restarts counting of the WDT period. When the time counting goes over the preset period of WDT, it will assume that the program operation is abnormal. A reset signal will start when such error happens. User can also use AL, 00H’s defined time for reset purposes, e.g.00H for Disable, 01H = 1sec, 02H=2sec….FFH=255sec. 3.18 Audio Connectors The HS-1743 has an onboard AC97 3D audio controller. CN20(Green) is for Line Out, CN20(Pink) is for MIC in. HS-1743 also support one extended speaker out with 2W amplifier. z 22 CN25/CN26: Stereo Speaker Amplifier PIN Description 1 2 3 +SPK_RO/+SPK_LO GND -SPK_RO/-SPK_LO 3 1 3.19 CompactFlash Socket The HS-1743 also offers a Type II CompactFlash socket via IDE interface located at the solder side of the board. The designated CN28 socket, once soldered with an adapter, can hold CompactFlash cards of various sizes. Please turn off the power before inserting the CF card. z CN28: CompactFlash Socket PIN Description PIN Description 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 GND IDE_PDD4 IDE_PDD6 IDE_PDCS1# GND GND +3.3V GND GND IDE_PDA1 IDE_PDD0 IDE_PDD2 GND IDE_PDD11 IDE_PDD13 IDE_PDD15 GND IDE_PDIOW# INT_IRQ15 +3.3V RESET# CF_PDERQ IDE_ACTP# IDE_PDD8 IDE_PDD10 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 IDE_PDD3 IDE_PDD5 IDE_PDD7 GND GND GND GND GND IDE_PDA2 IDE_PDA0 IDE_PDD1 GND GND IDE_PDD12 IDE_PDD14 IDE_PDCS3# IDE_PDIOR# +3.3V +3.3V N/C IDE_PDIORDY CF_REGB DETECT IDE_PDD9 GND Inserting a CompactFlash card into the adapter is not a difficult task. The socket and card are both keyed and there is only one direction for the card to be completely inserted. Refer to the diagram on the following page for the traditional way of inserting the card. 23 id e Fa Ma br de iq in ue J A ap u an Ja / po n R ea rS CE C F C om pa ct Fl as hT M PC Si B de So V i l de ew r z JP1: CF Use Master/Slave Select Options Setting Master (default) Slave Short Open 2 1 3.20 Expansion Interface The HS-1743 offers one Type III mini PCI socket at CN24, one PCIe x1 socket at CN27, and one PCI socket at PCI1. 24 3.21 8-bit GPIO Function The HS-1743 offers one 8-bit general purpose input/output port. z CN21: 8-bit GPIO PIN Description PIN Description 1 VCC 2 3 GD0 4 5 GD1 6 7 GD2 8 9 GD3 10 W83627EHG Digital I/O Assembly sample code -----------------------------------Extended function mode -----------------------------------MOV DX,2EH MOV AL,87H OUT DX,AL OUT DX,AL ------------------------------------Configure logical device 7 ------------------------------------MOV DX,2EH MOV AL,07H OUT DX,AL MOV DX,2FH MOV AL,07H OUT DX,AL MOV DX,2EH MOV AL,30H ; Enable GPIO1 OUT DX,AL MOV DX,2FH MOV AL,01H OUT DX,AL GND GD4 GD5 GD6 GD7 2 10 1 9 25 --------------------------------------Configure input / output --------------------------------------MOV DX,2EH MOV AL,F0H OUT DX,AL MOV DX,2FH MOV AL,FEH ; Setup GPIO bit0 as output, 0: output 1: input OUT DX,AL 26 Chapter 4 AMI BIOS Setup The HS-1743 uses AMI BIOS for the system configuration. The AMI BIOS setup program is designed to provide the maximum flexibility in configuring the system by offering various options that could be selected for end-user requirements. This chapter is written to assist you in the proper usage of these features. 4.1 Starting Setup The AMI BIOS is immediately activated when you first power on the computer. The BIOS reads the system information contained in the CMOS and begins the process of checking out the system and configuring it. When it finishes, the BIOS will seek an operating system on one of the disks and then launch and turn control over to the operating system. While the BIOS is in control, the Setup program can be activated in one of two ways: 1. By pressing <Del> immediately after switching the system on, or 2. By pressing the <F1> key when the following message appears briefly at the bottom of the screen during the POST (Power On Self Test). Press F1 to Run SETUP. 27 4.2 Using Setup In general, you use the arrow keys to highlight items, press <Enter> to select, and press <Esc> to quit. The following table provides more detail about how to navigate in the Setup program using the keyboard. ↑ ↓ ← → Esc key PgUp key PgDn key + key - key F1 key F2 key F3 key F4 key F5 key F6 key F7 key F8 key F9 key F10 key 28 Move to previous item Move to next item Move to previous item Move to previous item Main Menu -- Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu -Exit current page and return to Main Menu Move to top item Move to bottom item Increase the numeric value or make changes Decrease the numeric value or make changes General Help Change background color forward Change background color backward Reserved Reserved Reserved Reserved Reserved Reserved Save all the CMOS changes 4.3 Main Menu Once you enter the AMI BIOS CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions and two exit choices. Use the arrow keys to select among the items and press <Enter> to enter the sub-menu. BIOS SETUP UTILITY Main Advanced PCIPnP System Overview AMIBIOS Version : 08.00.13 Build Date : 9/14/10 ID : HS17430F Boot Security Chipset Exit Processor Type : Intel(R) Core(TM) Solo CPU U1500 Speed : 1333MHz Count : 1 System Memory Size : 1016MB System Time System Date Select Screen Select Item [00:29:32] [Tue 01/01/2002] ª - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. NOTE: A brief description of the highlighted choice appears at the bottom of the screen. 29 4.4 Advanced Settings This section allows you to configure your system for the basic operation. You have the opportunity to select the system’s default speed, boot-up sequence, keyboard operation, shadowing and security. BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Advanced Settings WARNING: Setting wrong values in below sections may cause system to malfunction. CPU Configuration IDE Configuration SuperIO Configuration Hardware Health Configuration ACPI Configuration APM Configuration PCI Express Configuration USB Configuration Exit Select Screen Select Item ª - Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. 30 BIOS SETUP UTILITY Main Advanced PCIPnP Boot Configure advanced CPU settings Module Version –13.04 Manufacturer : Intel Intel(R) Core(TM) Solo CPU U1500 @1.33GHz Frequency : 1.33GHz FSB Speed : 533MHz Cache L1 : 32 KB Cache L2 : 2048 KB Ratio Actual Value : 10 Security Chipset Exit Max CPUID Value Limit [Disabled] Select Screen Intel(R) Virtualization Tech [Enabled] Select Item Execute-disable bit capability [Enabled] ª - Change Field Hyper Threading Technology [Disabled] Tab Select Field DTS-based Thermal Management [Enabled] F1 General Help DTS Calibration [Enabled] F10 Save and Exit Intel(R) C-STATE tech. [Enabled] ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. BIOS SETUP UTILITY Main Advanced IDE Configuration PCIPnP ATA/IDE Configuration Configure SATA as Configure SATA Channels Port2 SATA AHCI Speed Primary IDE Master Primary IDE Slave Secondary IDE Master Secondary IDE Slave Third IDE Master Third IDE Slave Boot Security Chipset Exit [Enhanced] [IDE] [Before PATA] : GEN 1 (1.5 Gb/sec) : : : : : : [Not Detected] [Hard Disk] [Not Detected] [Not Detected] [Not Detected] [Not Detected] Select Screen Select Item ª - Change Field Tab Select Field Hard Disk Write Protect [Disabled] F1 General Help IDE Detect Time Out (Sec) [35] F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. 31 BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Configure WIN627EHF Super IO Chipset Parallel Port Address [378] Parallel Port Mode [Normal] Parallel Port IRQ [IRQ7] Serial Port1 Address [3E8] Serial Port1 Mode [11] Serial Port2 Address [2E8] Serial Port2 Mode [10] Serial Port3 Address [2F0] Serial Port3 Mode [11] Serial Port4 Address [2E0] Serial Port4 Mode [10] Serial Port5 Address [2D8] Serial Port5 Mode [11] Select Screen Serial Port6 Address [2D0] Select Item Serial Port6 Mode [10] ª Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. BIOS SETUP UTILITY Main Advanced PCIPnP Hardware Health Configuration System Temperature CPU Temperature Boot SYSFAN Speed CPUFAN0 Speed : 0 RPM : 6750 RPM Vcore +12V +1.5V +1.05V +5V VBAT : : : : : : : 32 Security Chipset Exit : 43°C/109°F : 46°C/114°F 1.200 V 11.880 V 1.592 V 1.024 V 5.094 V 3.216 V Select Screen Select Item ª Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. BIOS SETUP UTILITY Main Advanced ACPI Settings ACPI Aware O/S PCIPnP Boot Security Chipset Exit [Yes] Advanced ACPI Configuration Chipset ACPI Configuration Select Screen Select Item ª Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. BIOS SETUP UTILITY Main Advanced PCIPnP Advanced ACPI Configuration ACPI Version Features ACPI APIC support AMI 0EMB table Headless mode Boot Security Chipset Exit [ACPI v1.0] [Enabled] [Enabled] [Disabled] Select Screen Select Item ª Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. BIOS SETUP UTILITY Main Advanced PCIPnP Chipset ACPI Configuration Energy Lake Feature APIC ACPI SCI IRQ USB Device Wakeup From S3/S4 Boot Security Chipset Exit [Disabled] [Disabled] [Disabled] Select Screen Select Item ª Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. 33 BIOS SETUP UTILITY Main Advanced PCIPnP APM Configuration Power Management/APM Video Power Down Mode Hard Disk Power Down Mode Suspend Time Out Throttle Slow Clock Ratio Keyboard & PS/2 Mouse Boot Power Button Mode [On/Off] Security Chipset Exit [Enabled] [Disabled] [Disabled] [Disabled] [50%] [MONITOR] Select Screen Select Item Advanced Resume Event Controls ª Change Field Resume On Ring [Disabled] Tab Select Field Resume On LAN [Disabled] F1 General Help Resume On PME# [Disabled] F10 Save and Exit Resume On RTC Alarm [Disabled] ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. BIOS SETUP UTILITY Main Advanced PCIPnP Active State Power-Management Boot Security Chipset Exit [Disabled] Select Screen Select Item ª Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. 34 4.5 Advanced PCI/PnP Settings This section describes configuring the PCI bus system. PCI, or Personal Computer Interconnect, is a system that allows I/O devices to operate at speeds nearing the speed the CPU itself uses when communicating with its own special components. This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings. BIOS SETUP UTILITY Main Advanced PCIPnP Advanced PCI/PnP Settings Boot Security Chipset Exit WARNING: Setting wrong values in below sections may cause system to malfunction. Clean NVRAM [No] Plug & Play O/S [No] PCI Latency Timer [64] Allocate IRQ to PCI VGA [Yes] Palette Snooping [Disabled] PCI IDE BusMaster [Enabled] Offboard PCI/ISA IDE Card [Auto] IRQ3 IRQ4 IRQ5 IRQ7 IRQ9 IRQ10 IRQ11 IRQ14 IRQ15 DMA DMA DMA DMA DMA DMA Channel Channel Channel Channel Channel Channel [Available] [Available] [Available] [Available] [Available] [Available] [Available] [Available] [Available] 0 1 3 5 6 7 [Available] [Available] [Available] [Available] [Available] [Available] Select Screen Select Item ª Change Field Tab Select Field F1 General Help F10 Save and Exit Reserved Memory Size [Disabled] ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. 35 4.6 Boot Settings BIOS SETUP UTILITY Main Advanced PCIPnP Boot Settings Boot Settings Configuration Boot Security Chipset Exit Select Screen Select Item ª Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. Boot Device Priority Hard Disk Drives USB Drives BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Boot Settings Configuration Quick Boot [Enabled] Quiet Boot [Disabled] LAN Boot ROM [Disabled] Select Screen AddOn ROM Display Mode [Force BIOS] Select Item Bootup Nom-Lock [On] ª Change Field PS/2 Mouse Support [Auto] Tab Select Field Wait For ‘F1’ If Error [Disabled] F1 General Help Hit ‘DEL’ Message Display [Disabled] F10 Save and Exit Interrupt 19 Capture [Disabled] ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. 4.7 Security Settings BIOS SETUP UTILITY Main Advanced Security Settings Supervisor Password User Password PCIPnP Boot Security Chipset Exit : Not Installed : Not Installed Select Screen Select Item ª Change Field [Disabled] Tab Select Field F1 General Help Hard Disk Security F10 Save and Exit There are no supported Hard Disks. ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. Change Supervisor Password Change User Password Boot Sector Virus Protection 36 4.8 Advanced Chipset Settings BIOS SETUP UTILITY Main Advanced PCIPnP Advanced Chipset Settings Boot Security Chipset Exit WARNING: Setting wrong values in below sections may cause system to malfunction. North Bridge Chipset Configuration South Bridge Chipset Configuration Select Screen Select Item ª Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. BIOS SETUP UTILITY Main Advanced PCIPnP Boot North Bridge Chipset Configuration Security DRAM Frequency Configure DRAM Timing by SPD Memory Hole [Auto] [Enabled] [Disabled] Boots Graphic Adapter Priority Internal Graphics Mode Select [PEG/PCI] [Enabled, 8MB] PEG Port Configuration PEG Port PEG Force x1 [Auto] [Disabled] Chipset Exit Select Screen Select Item ª Change Field Tab Select Field F1 General Help Video Function Configuration F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. Chipset Thermal Throttling DT in SPD TS on DIMM [Disabled] [Disabled] [Disabled] 37 BIOS SETUP UTILITY Main Advanced PCIPnP Video Function Configuration DVMT Mode Select DVMT/FIXED Memory Boot Security Chipset Exit [DVMT Mode] [128MB] Select Screen Select Item Boot Display Device [CRT + DVI] ª - Change Field Flat Panel Type [1024x768 18bit 2CH] Tab Select Field F1 General Help F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. BIOS SETUP UTILITY Main Advanced PCIPnP Boot South Bridge Chipset Configuration USB Function USB 2.0 Controller Audio Controller SMBUS Controller Security Chipset Exit [8 USB Ports] [Enabled] [AC’97 Audio Only] [Enabled] Select Screen Select Item ª - Change Field SLP_S4# Min. Assertion Width [1 to 2 seconds] Tab Select Field Restore on AC Power Loss [Power On] F1 General Help F10 Save and Exit ASF Support [Enabled] ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. 4.9 Exit Options BIOS SETUP UTILITY Main Advanced PCIPnP Exit Options Save Changes and Exit Discard Changes and Exit Discard Changes Boot Security Chipset Exit Select Screen Select Item ª - Change Field Load Optimal Defaults Tab Select Field Load Failsafe Defaults F1 General Help F10 Save and Exit ESC Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. 38 Chapter 5 Software Utilities This chapter contains the detailed information of IDE, VGA, LAN and audio driver installation procedures. The utility disk that comes with the delivery package contains an auto-run program that invokes the installation programs for the IDE, VGA, LAN and audio drivers. The following sections describe the installation procedures of each driver based on WIN2K/XP operating systems. It is recommended that you install the drivers matching the sections listed in this chapter. 5.1 1. Chipset Driver Installation Insert the CD that comes with the board into the CD-ROM drive. Click CHIPSET to install Intel® 945GME/ICH7-M chipset driver. 39 2. Once the Install Shield Wizard screen appears on the screen, make sure to close applications that are running and then click on Next> button. 3. The Welcome screen is now displayed, and then click on Next> button to continue. 40 4. The License Agreement dialog box then appears on the screen. Choose Yes to proceed. 5. When the Readme File Information dialog box pops up, just click on the Next > button to proceed. 41 6. 5.2 1. 42 The Installation Utility successfully installed Plug and Play components onto the system. Click Finish to exit setup. VGA Driver Installation Insert the CD that comes with the board into the CD-ROM drive. Click VGA to install Intel® 945GME video driver. 2. Once the InstallShield Wizard appears on the screen and click on the Next > button. 3. InstallShield Wizard will extracting files to your hard drive, and then click on Next> to continue. 43 4. When the dialog box below appears, make sure you close all other Windows applications then click on the Next > button to proceed. 5. The Intel® OEM Software License Agreement dialog box appears on the screen. Choose Yes to proceed. 44 6. 5.3 1. Once InstallShield Wizard finishes updating your system, it will prompt you to restart the computer. Tick on the Yes, I want to restart my computer now followed by a click on the Finish button to reboot. Only after your computer reboot and the new setting will be take effect. Audio Driver Installation Insert the CD that comes with the board into the CD-ROM drive. Click Audio to install RealTek AC97 audio driver. 45 2. Once the Install Shield Wizard screen appears on the screen, make sure to close applications that are running. 3. Realtek AC97 Audio Setup is preparing the Install Shield Wizard, which will guide you through the rest of the setup process. Click on Next> to process. 46 4. Realtek AC97 Audio is configuring your new software installation. 5. After all installation finish, you will be prompted to start your system, click on the Finish button to reboot. 47 5.4 48 LAN Driver Installation 1. Insert the CD that comes with the board into the CD-ROM drive. Click LAN to install network driver. 2. The License Agreement dialog box then appears on the screen, choose Next> to proceed. 3. Click on the Advanced Network Services, and press Next> to proceed. 4. Click Install to being the installation. 49 5. 50 When the dialog box below appears, make sure you close all other Windows applications the click on the Finish button to proceed.