aPR2060 --- H2.2 - Aplus Integrated Circuits Inc.

Integrated Circuits Inc.
aPR2060-H2.2
aPR2060 --- H2.2
Datasheet
40 ~ 80 sec recording voice IC
APLUS INTEGRATED CIRCUITS INC.
Address : 3 F-10, No. 32, Sec. 1, Chenggung Rd., Taipei, Taiwan 115, R.O.C.
TEL : 886-2-2782-9266
WEBSITE
FAX :
:
Sales E-mail :
http://www.aplusinc.com.tw
Technology E-mail
Ver. A
886-2-2782-9255
:
[email protected]
[email protected]
1/14
JUN. 13, 2014
Integrated Circuits Inc.
aPR2060-H2.2
FEATURES :
Operating Voltage Range: 3V ~ 6.5V
Single Chip, High Quality Audio/Voice Recording & Playback Solution
No External ICs Required
Minimum External Components
User Friendly, Easy to Use Operation
Programming & Development Systems Not Required
40 ~ 80 sec. Voice Recording Length
Powerful 16-Bits Digital Audio Processor.
Nonvolatile Flash Memory Technology
No Battery Backup Required
External Reset pin.
Powerful Power Management Unit
Very Low Standby Current: 1uA
Low Power-Down Current: 10uA
Supports Power-Down Mode for Power Saving
Built-in Audio-Recording Microphone Amplifier
No External OPAMP or BJT Required
Easy to PCB layout
Configurable analog interface
Differential-ended MIC pre-amp for Low Noise
High Quality Line Receiver
High Quality Analog to Digital, DAC and PWM module
Resolution up to 16-bits
Simple And Direct User Interface
one messages 40s to 60s record & playback
Adjustable sample rates` by external resistors
Ver. A
2/14
JUN. 13, 2014
Integrated Circuits Inc.
aPR2060-H2.2
DESCRIPTION :
Today’s consumers demand the best in audio/voice. They want crystal-clear
sound wherever they are in whatever format they want to use. APLUS
delivers the technology to enhance a listener’s audio/voice experience.
The aPR2060 is powerful audio processor along with high performance
audio analog-to-digital converters (ADCs) and digital-to-analog converters
(DACs). The aPR2060 are a fully integrated solution offering high
performance and unparalleled integration with analog input, digital
processing and analog output functionality. The aPR2060 incorporates all
the functionality required to perform demanding audio/voice applications.
High quality audio/voice systems with lower bill-of-material costs can be
implemented with the aPR2060 because of its integrated analog data
converters and full suite of quality-enhancing features such as sample-rate
convertor.
The aPR2060 H2.2 is specially designed for 2 key trigger, user can
record and playback the voice message by switch, It is suitable in simple
interface or need to limit the length of single message, e.g. toys, leave
messages system, answering machine etc.
Meanwhile, this mode provides the power-management system. Users can
let the chip enter power-down mode when unused. It can effectively reduce
electric current consuming to 10uA and increase the using time in any
projects powered by batteries.
Ver. A
3/14
JUN. 13, 2014
Integrated Circuits Inc.
aPR2060-H2.2
PIN CONFIGURATION :
Ver. A
4/14
JUN. 13, 2014
Integrated Circuits Inc.
Ver. A
5/14
aPR2060-H2.2
JUN. 13, 2014
Integrated Circuits Inc.
aPR2060-H2.2
PIN DESCRIPTION :
Pin Names
Pin No
VDDP
9
10
VDD
TYPE
Description
Positive power supply.
1
VSSL
VSSP
VSSA
6
17
Power ground.
VCORE
2
Positive power supply for core.
VREF
12
Reference voltage.
VCM
18
Common mode voltage.
Rosc
3
INPUT
Oscillator resistor input.
RSTB
11
INPUT
Reset. (Low active)
MIC+
MIC-
19
20
INPUT
Microphone differential input.
MICG
16
OUTPUT
Enable Microphone ground.
VOUT1
7
OUTPUT
VOUT2
8
OUTPUT
PWM output to drive speaker directly.
DAC output.
/REC
15
INPUT
---
M0
4
INPUT
Record Voice Message
M1
14
INPUT
Play Voice Message
M2
5
INPUT
LED output
M3
13
INPUT
---
Ver. A
PWM output to drive speaker directly.
DAC option.[ Vout1 pull high 1K Ohm ]
6/14
JUN. 13, 2014
Integrated Circuits Inc.
aPR2060-H2.2
RECORD MESSAGE :
Start record voice message :
When the [ M0 ] key drove to VIL [ VSS ] in record mode, the chip will
playback “beep” tone and M2 LED on and message record starting.
Stop record voice message :
The message record will continue until [ M0 ] key released or full of this
message,the chip will play “beep” tone to indicate the message stop record
and LED off.
If the message already exist and user record again, the old one’s message
will be replaced.
PLAYBACK MESSAGE :
Start playback voice message :
When the [ M1 ] key drove from VIH to VIL in playback mode, the message
playback starting and LED on.
Stop playback voice message :
The message playback will continue until [ M1 ] key drove from VIH to VIL
again or end of this message and LED off.
Note: After reset, M0 to M1 pin will be pull-up to VDD by internal resistor.
Ver. A
7/14
JUN. 13, 2014
Integrated Circuits Inc.
aPR2060-H2.2
BLOCK DIAGRAM :
Figure 1. Block Diagram
ABSOLUTE MAXIMUM RATINGS :
Ver. A
Symbol
Rating
Unit
VDD – VSS
-0.3 ~ +10.0
V
VIN
VSS-0.3 < VIN < VDD+0.3
V
VOUT
VSS < VOUT < VDD
V
T(Operating)
-40 ~ +85
℃
T(Junction)
-40 ~ +125
℃
T(Storage)
-40 ~ +125
℃
8/14
JUN. 13, 2014
aPR2060-H2.2
Integrated Circuits Inc.
DC CHARACTERISTICS :
Symbol
Parameter
VDD
Operating Voltage
ISB
Standby Current
IPDN
Power-Down Current
10
µA
IOP(IDLE)
Operating Current (Idle)
20
mA
VDD = 5V
IOP(REC)
Operating Current (Record)
35
mA
VDD = 5V
IOP(PLAY)
Operating Current (Playback)
25
mA
VDD = 5V
VIH
"H" Input Voltage
VIL
"L" Input Voltage
IVOUT
VOUT Current
185
mA
IOH
O/P High Current
8
mA
VDD = 5V / VOH=4.5V
IOL
O/P Low Current
14
mA
VDD = 5V / VOH=0.5V
Input pin pull-down
resistance
300
KΩ
External floating or drive
low.
1
MΩ
External drive high.
RUPIO
Input pin pull-up resistance
4.7
KΩ
△Fs/Fs
Frequency stability
5
%
VDD = 5V ± 1.0V
△Fc/Fc
Chip to chip Frequency
Variation
5
%
Also apply to lot to lot
variation.
RNPIO
Ver. A
Min. Typ. Max. Unit
3.0
6.5
V
1
µA
2.5
V
0.6
9/14
Conditions
V
JUN. 13, 2014
aPR2060-H2.2
Integrated Circuits Inc.
■
SAMPLES RATES & RESISTANCE VALUES ( for reference only )
Sample Rate
Seconds
Resistance
12KHz
42 sec
47K
11KHz
46 sec
63K
10KHz
51 sec
79K
9KHz
56 sec
100K
8KHz
64 sec
120K
7KHz
73 sec
143K
6KHz
85 sec
173K
AC CHARACTERISTICS :
Symbol
Parameter
Min.
Typ.
Max.
Unit
Conditions
T1
System Initial Time
100
--
--
mS
VDD=5.0V
T2
Trigger Setup Time
16
--
--
mS
VDD=5.0V
T3
Trigger Hold Time
16
--
--
mS
VDD=5.0V
T4
Reset Hold Time
100
--
--
uS
VDD=5.0V
Ver. A
10/14
JUN. 13, 2014
Integrated Circuits Inc.
aPR2060-H2.2
BONDING PAD DIAGRAMS :
Ver. A
11/14
JUN. 13, 2014
aPR2060-H2.2
Integrated Circuits Inc.
Die Size
2400 X 3000
Pad Size
80 X 80
Pad No
Pad
Pad Location
Pad No
Name
X
Y
1
VSSL
920
1080
2
VCORE
635
3
N.C.
4
Pad
Pad Location
Name
X
Y
14
VDDA
1780
101
1080
15
RSTB
1900
101
270
1080
16
VREF
2020
101
ROSC
102.4
840
17
N.C.
2293.6
108
5
N.C.
102.4
720
18
M3/MSEL1
2293.6
228
6
M0
102.4
600
19
M1
2293.6
348
7
M2/MSEL0
102.4
480
20
/REC
2293.6
468
8
N.C.
102.4
360
21
MICG
2293.6
588
9
VSSP
102.4
240
22
VSSA
2210
775
10
VOUT1
310
101
23
VCM
2025
775
11
VOUT2
420
101
24
MIC+
1905
775
12
VDDL
530
101
25
MIC-
1785
775
13
VDDP
640
101
Unit : [ um ]
Ver. A
12/14
JUN. 13, 2014
Integrated Circuits Inc.
aPR2060-H2.2
PACKAGES DIMENSION OUTLINES
20-Pin 300mil DIP Package
20-Pin 300mil SOP Package
Ver. A
13/14
JUN. 13, 2014
Integrated Circuits Inc.
aPR2060-H2.2
HISTORY
Ver. A (2014/06/13) :
- Original version data sheet for aPR2060 H2.2.
Ver. A
14/14
JUN. 13, 2014