Integrated Circuits Inc. aPR2060-H2.1 aPR2060 --- H2.1 Datasheet 40 ~ 80 sec recording voice IC APLUS INTEGRATED CIRCUITS INC. Address : 3 F-10, No. 32, Sec. 1, Chenggung Rd., Taipei, Taiwan 115, R.O.C. TEL : 886-2-2782-9266 WEBSITE FAX : : Sales E-mail : http://www.aplusinc.com.tw Technology E-mail Ver. B 886-2-2782-9255 : [email protected] [email protected] 1/14 JUN. 13, 2014 Integrated Circuits Inc. aPR2060-H2.1 FEATURES : Operating Voltage Range: 3V ~ 6.5V Single Chip, High Quality Audio/Voice Recording & Playback Solution No External ICs Required Minimum External Components User Friendly, Easy to Use Operation Programming & Development Systems Not Required 40 ~ 80 sec. Voice Recording Length Powerful 16-Bits Digital Audio Processor. Nonvolatile Flash Memory Technology No Battery Backup Required External Reset pin. Powerful Power Management Unit Very Low Standby Current: 1uA Low Power-Down Current: 10uA Supports Power-Down Mode for Power Saving Built-in Audio-Recording Microphone Amplifier No External OPAMP or BJT Required Easy to PCB layout Configurable analog interface Differential-ended MIC pre-amp for Low Noise High Quality Line Receiver High Quality Analog to Digital, DAC and PWM module Resolution up to 16-bits Simple And Direct User Interface one messages 40s to 60s record & playback Adjustable sample rates` by external resistors Ver. B 2/14 JUN. 13, 2014 Integrated Circuits Inc. aPR2060-H2.1 DESCRIPTION : Today’s consumers demand the best in audio/voice. They want crystal-clear sound wherever they are in whatever format they want to use. APLUS delivers the technology to enhance a listener’s audio/voice experience. The aPR2060 is powerful audio processor along with high performance audio analog-to-digital converters (ADCs) and digital-to-analog converters (DACs). The aPR2060 are a fully integrated solution offering high performance and unparalleled integration with analog input, digital processing and analog output functionality. The aPR2060 incorporates all the functionality required to perform demanding audio/voice applications. High quality audio/voice systems with lower bill-of-material costs can be implemented with the aPR2060 because of its integrated analog data converters and full suite of quality-enhancing features such as sample-rate convertor. The aPR2060 H2.1 is specially designed for 2 key trigger, user can record and playback the voice message by switch, It is suitable in simple interface or need to limit the length of single message, e.g. toys, leave messages system, answering machine etc. Meanwhile, this mode provides the power-management system. Users can let the chip enter power-down mode when unused. It can effectively reduce electric current consuming to 10uA and increase the using time in any projects powered by batteries. Ver. B 3/14 JUN. 13, 2014 Integrated Circuits Inc. aPR2060-H2.1 PIN CONFIGURATION : Ver. B 4/14 JUN. 13, 2014 Integrated Circuits Inc. Ver. B 5/14 aPR2060-H2.1 JUN. 13, 2014 Integrated Circuits Inc. aPR2060-H2.1 PIN DESCRIPTION : Pin Names Pin No VDDP 9 10 VDD TYPE Description Positive power supply. 1 VSSL VSSP VSSA 6 17 Power ground. VCORE 2 Positive power supply for core. VREF 12 Reference voltage. VCM 18 Common mode voltage. Rosc 3 INPUT Oscillator resistor input. RSTB 11 INPUT Reset. (Low active) MIC+ MIC- 19 20 INPUT Microphone differential input. MICG 16 OUTPUT Enable Microphone ground. VOUT1 7 OUTPUT VOUT2 8 OUTPUT PWM output to drive speaker directly. DAC output. /REC 15 INPUT --- M0 4 INPUT Record Voice Message M1 14 INPUT Play Voice Message M2 5 INPUT LED output M3 13 INPUT --- Ver. B PWM output to drive speaker directly. DAC option.[ Vout1 pull high 1K Ohm ] 6/14 JUN. 13, 2014 Integrated Circuits Inc. aPR2060-H2.1 RECORD MESSAGE : Start record voice message : When the [ M0 ] key drove to VIL [ VSS ] in record mode, the chip will playback “beep” tone and M2 LED on and message record starting. Stop record voice message : The message record will continue until [ M0 ] key released or full of this message,the chip will play “beep” tone to indicate the message stop record and LED off. If the message already exist and user record again, the old one’s message will be replaced. PLAYBACK MESSAGE : Start playback voice message : When the [ M1 ] key drove from VIH to VIL in playback mode, the message playback starting and LED on. Stop playback voice message : The message playback will continue until [ M1 ] key drove from VIH to VIL again or end of this message and LED off. Note: After reset, M0 to M1 pin will be pull-up to VDD by internal resistor. Ver. B 7/14 JUN. 13, 2014 Integrated Circuits Inc. aPR2060-H2.1 BLOCK DIAGRAM : Figure 1. Block Diagram ABSOLUTE MAXIMUM RATINGS : Ver. B Symbol Rating Unit VDD – VSS -0.3 ~ +10.0 V VIN VSS-0.3 < VIN < VDD+0.3 V VOUT VSS < VOUT < VDD V T(Operating) -40 ~ +85 ℃ T(Junction) -40 ~ +125 ℃ T(Storage) -40 ~ +125 ℃ 8/14 JUN. 13, 2014 aPR2060-H2.1 Integrated Circuits Inc. DC CHARACTERISTICS : Symbol Parameter VDD Operating Voltage ISB Standby Current IPDN Power-Down Current 10 µA IOP(IDLE) Operating Current (Idle) 20 mA VDD = 5V IOP(REC) Operating Current (Record) 35 mA VDD = 5V IOP(PLAY) Operating Current (Playback) 25 mA VDD = 5V VIH "H" Input Voltage VIL "L" Input Voltage IVOUT VOUT Current 185 mA IOH O/P High Current 8 mA VDD = 5V / VOH=4.5V IOL O/P Low Current 14 mA VDD = 5V / VOH=0.5V Input pin pull-down resistance 300 KΩ External floating or drive low. 1 MΩ External drive high. RUPIO Input pin pull-up resistance 4.7 KΩ △Fs/Fs Frequency stability 5 % VDD = 5V ± 1.0V △Fc/Fc Chip to chip Frequency Variation 5 % Also apply to lot to lot variation. RNPIO Ver. B Min. Typ. Max. Unit 3.0 6.5 V 1 µA 2.5 V 0.6 9/14 Conditions V JUN. 13, 2014 aPR2060-H2.1 Integrated Circuits Inc. ■ SAMPLES RATES & RESISTANCE VALUES ( for reference only ) Sample Rate Seconds Resistance 12KHz 42 sec 47K 11KHz 46 sec 63K 10KHz 51 sec 79K 9KHz 56 sec 100K 8KHz 64 sec 120K 7KHz 73 sec 143K 6KHz 85 sec 173K AC CHARACTERISTICS : Symbol Parameter Min. Typ. Max. Unit Conditions T1 System Initial Time 100 -- -- mS VDD=5.0V T2 Trigger Setup Time 16 -- -- mS VDD=5.0V T3 Trigger Hold Time 16 -- -- mS VDD=5.0V T4 Reset Hold Time 100 -- -- uS VDD=5.0V Ver. B 10/14 JUN. 13, 2014 Integrated Circuits Inc. aPR2060-H2.1 BONDING PAD DIAGRAMS : Ver. B 11/14 JUN. 13, 2014 aPR2060-H2.1 Integrated Circuits Inc. Die Size 2400 X 3000 Pad Size 80 X 80 Pad No Pad Pad Location Pad No Name X Y 1 VSSL 920 1080 2 VCORE 635 3 N.C. 4 Pad Pad Location Name X Y 14 VDDA 1780 101 1080 15 RSTB 1900 101 270 1080 16 VREF 2020 101 ROSC 102.4 840 17 N.C. 2293.6 108 5 N.C. 102.4 720 18 M3/MSEL1 2293.6 228 6 M0 102.4 600 19 M1 2293.6 348 7 M2/MSEL0 102.4 480 20 /REC 2293.6 468 8 N.C. 102.4 360 21 MICG 2293.6 588 9 VSSP 102.4 240 22 VSSA 2210 775 10 VOUT1 310 101 23 VCM 2025 775 11 VOUT2 420 101 24 MIC+ 1905 775 12 VDDL 530 101 25 MIC- 1785 775 13 VDDP 640 101 Unit : [ um ] Ver. B 12/14 JUN. 13, 2014 Integrated Circuits Inc. aPR2060-H2.1 PACKAGES DIMENSION OUTLINES 20-Pin 300mil DIP Package 20-Pin 300mil SOP Package Ver. B 13/14 JUN. 13, 2014 Integrated Circuits Inc. aPR2060-H2.1 HISTORY Ver. A (2014/05/15) : - Original version data sheet for aPR2060 H2.1. Ver. B ( 2014/06/13 ) : --- modify the page-4 & page-5 application circuit Ver. B 14/14 JUN. 13, 2014