AD ADR293GRZ

Low Noise, Micropower
5.0 V Precision Voltage Reference
ADR293
FEATURES
PIN CONFIGURATIONS
6.0 V to 15 V supply range
Supply current: 15 μA maximum
Low noise: 15 μV p-p typical (0.1 Hz to 10 Hz)
High output current: 5 mA
Temperature range: −40°C to +125°C
Pin-compatible with the REF02/REF19x
NC 1
VIN 2
8
ADR293
NC
NC
TOP VIEW
6 VOUT
(Not to Scale)
5 NC
GND 4
7
NC = NO CONNECT
00164-001
NC 3
Figure 1. 8-Lead Narrow Body SOIC (R-8)
Portable instrumentation
Precision reference for 5 V systems
ADC and DAC reference
Solar-powered applications
Loop-current powered instruments
NC
1
8
NC
VIN
2
ADR293
7
NC
NC
3
TOP VIEW
(Not to Scale)
6
VOUT
GND
4
5
NC
NC = NO CONNECT
00164-002
APPLICATIONS
Figure 2. 8-Lead TSSOP (RU-8)
GENERAL DESCRIPTION
The ADR293 is a low noise, micropower precision voltage
reference that utilizes an XFET® (eXtra implanted junction FET)
reference circuit. The XFET architecture offers significant
performance improvements over traditional band gap and
buried Zener-based references. Improvements include one
quarter the voltage noise output of band gap references
operating at the same current, very low and ultralinear
temperature drift, low thermal hysteresis, and excellent longterm stability.
The ADR293 is a series voltage reference providing stable and
accurate output voltage from a 6.0 V supply. Quiescent current
is only 15 μA maximum, making this device ideal for battery
powered instrumentation. Three electrical grades are available
offering initial output accuracy of ±3 mV, ±6 mV, and ±10 mV.
Temperature coefficients for the three grades are 8 ppm/°C,
15 ppm/°C, and 25 ppm/°C maximum. Line regulation and load
regulation are typically 30 ppm/V and 30 ppm/mA, respectively,
maintaining the reference’s overall high performance.
The ADR293 is specified over the extended industrial
temperature range of –40°C to +125°C. This device is available
in the 8-lead SOIC and 8-lead TSSOP packages.
Table 1. ADR29x Products
Device
ADR291
ADR292
ADR293
Output
Voltage (V)
2.500
4.096
5.000
Initial
Accuracy (%)
0.08, 0.12, 0.24
0.07, 0.10, 0.15
0.06, 0.12, 0.20
Temperature
Coefficient
(ppm/°C max)
8, 15, 25
8, 15, 25
8, 15, 25
Rev. D
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113 ©2001-2011 Analog Devices, Inc. All rights reserved.
ADR293
TABLE OF CONTENTS
Features .............................................................................................. 1
Terminology .......................................................................................9
Applications ....................................................................................... 1
Theory of Operation ...................................................................... 10
Pin Configurations ........................................................................... 1
Device Power Dissipation Considerations .............................. 10
General Description ......................................................................... 1
Basic Voltage Reference Connections ..................................... 10
Revision History ............................................................................... 2
Noise Performance ..................................................................... 10
Specifications..................................................................................... 3
Turn-On Time ............................................................................ 10
Electrical Specifications ............................................................... 3
Applications..................................................................................... 11
Absolute Maximum Ratings............................................................ 5
Kelvin Connections .................................................................... 11
Thermal Resistance ...................................................................... 5
Voltage Regulator for Portable Equipment ............................. 11
ESD Caution .................................................................................. 5
Outline Dimensions ....................................................................... 12
Typical Performance Characteristics ............................................. 6
Ordering Guide .......................................................................... 12
REVISION HISTORY
5/11—Rev. C to Rev. D
Delete Negative Precision Reference Without Precision
Resistors Section ............................................................................. 11
Delete Figure 23 and Figure 24, Renumbered Sequentially ...... 11
9/10—Rev. B to Rev. C
Changes to Table 2 and Table 3 ....................................................... 3
Changes to Table 4 ............................................................................ 4
Changes to Figure 10, Figure 11, Figure 13 ................................... 7
Changes to Captions for Figure 17 to Figure 19 ........................... 8
6/07—Rev. A to Rev. B
Updated Format .................................................................. Universal
Changes to Table 1.............................................................................1
Updated Outline Dimensions ....................................................... 13
Changes to Ordering Guide .......................................................... 13
3/01—Rev. 0 to Rev. A
Rev. D | Page 2 of 12
ADR293
SPECIFICATIONS
ELECTRICAL SPECIFICATIONS
VS = 6.0 V, TA = 25°C, unless otherwise noted.
Table 2.
Parameter
OUTPUT VOLTAGE
E Grade
F Grade
G Grade
INITIAL ACCURACY
E Grade
Symbol
VOUT
Conditions
IOUT = 0 mA
Min
Typ
Max
Unit
4.997
4.994
4.990
5.000
5.000
5.000
5.003
5.006
5.010
V
V
V
+3
0.06
+6
0.12
+10
0.20
mV
%
mV
%
mV
%
30
40
100
150
ppm/V
ppm/V
30
40
50
15
640
100
150
ppm/mA
ppm/mA
ppm
μV p-p
nV/√Hz
IOUT = 0 mA
–3
F Grade
–6
G Grade
–10
LINE REGULATION
E, F Grades
G Grade
LOAD REGULATION
E, F Grades
G Grade
LONG-TERM STABILITY
VOLTAGE NOISE
VOLTAGE NOISE DENSITY
ΔVOUT /ΔVIN
ΔVOUT /ΔILOAD
ΔVOUT
eN p-p
eN
6.0 V to 15 V, IOUT = 0 mA
VS = 6.0 V, IOUT = 0 mA to 5 mA
After 1000 hours of operation @ 125°C
f = 0.1 Hz to 10 Hz
f = 1 kHz
VS = 6.0 V, TA = −25°C to +85°C, unless otherwise noted.
Table 3.
Parameter
TEMPERATURE COEFFICIENT
E Grade
F Grade
G Grade
LINE REGULATION
E, F Grades
G Grade
LOAD REGULATION
E, F Grades
G Grade
Symbol
TCVOUT
ΔVOUT/ΔVIN
ΔVOUT/ΔILOAD
Conditions
IOUT = 0 mA
Min
Typ
Max
Unit
3
5
10
8
15
25
ppm/°C
ppm/°C
ppm/°C
35
50
150
200
ppm/V
ppm/V
20
30
150
200
ppm/mA
ppm/mA
6.0 V to 15 V, IOUT = 0 mA
VS = 6.0 V, IOUT = 0 mA to 5 mA
Rev. D | Page 3 of 12
ADR293
VS = 6.0 V, TA = −40°C to +125°C, unless otherwise noted.
Table 4.
Parameter
TEMPERATURE COEFFICIENT
E Grade
F Grade
G Grade
LINE REGULATION
E, F Grades
G Grade
LOAD REGULATION
E, F Grades
G Grade
SUPPLY CURRENT
THERMAL HYSTERESIS
Symbol
TCVOUT
ΔVOUT/ΔVIN
ΔVOUT/ΔILOAD
IS
VOUT-HYS
Conditions
IOUT = 0 mA
Min
Typ
Max
Unit
3
5
10
10
20
30
ppm/°C
ppm/°C
ppm/°C
40
70
200
250
ppm/V
ppm/V
@ 25°C
20
30
11
200
300
15
ppm/mA
ppm/mA
μA
20
8-lead SOIC_N
8-lead TSSOP
15
72
157
μA
ppm
ppm
6.0 V to 15 V, IOUT = 0 mA
VS = 6.0 V, IOUT = 0 mA to 5 mA
Rev. D | Page 4 of 12
ADR293
ABSOLUTE MAXIMUM RATINGS
THERMAL RESISTANCE
Table 5.
Parameter
Supply Voltage
Output Short-Circuit Duration to GND
Storage Temperature Range
Operating Temperature Range
Junction Temperature Range
Lead Temperature (Soldering, 60 sec)
Rating
18 V
Indefinite
−65°C to +150°C
−40°C to +125°C
−65°C to +150°C
300°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
θJA is specified for worst-case conditions; that is, θJA is specified
for the device in socket testing. In practice, θJA is specified for
the device soldered in a circuit board.
Table 6. Thermal Resistance
Package Type
8-Lead SOIC_N (R-8)
8-Lead TSSOP (RU-8)
ESD CAUTION
Rev. D | Page 5 of 12
θJA
158
240
θJC
43
43
Unit
°C/W
°C/W
ADR293
TYPICAL PERFORMANCE CHARACTERISTICS
TA = 25°C, unless otherwise noted.
5.006
100
VS = 6V
3 TYPICAL PARTS
VS = 6V TO 15V
LINE REGULATION (ppm/V)
5.002
5.000
4.998
80
60
40
20
4.996
–25
0
25
50
TEMPERATURE (°C)
75
100
125
0
–50
00164-003
4.994
–50
Figure 3. VOUT vs. Temperature
0
25
50
TEMPERATURE (°C)
75
100
125
Figure 6. Line Regulation vs. Temperature
100
16
14
TA = +125°C
12
TA = +25°C
IOUT = 0mA
VS = 6V TO 9V
LINE REGULATION (ppm/V)
SUPPLY CURRENT (µA)
–25
00164-006
OUTPUT VOLTAGE (V)
5.004
10
TA = –40°C
8
6
4
80
60
40
20
2
4
6
8
10
INPUT VOLTAGE (V)
12
14
16
0
–50
0
25
50
TEMPERATURE (°C)
75
100
125
5.0
Figure 7. Line Regulation vs. Temperature
Figure 4. Supply Current vs. Input Voltage
0.7
16
VS = 6V
0.6
DIFFERENTIAL VOLTAGE (V)
14
12
10
8
0.5
TA = +125°C
0.4
TA = +25°C
0.3
TA = –40°C
0.2
0.1
6
–50
–25
0
25
50
TEMPERATURE (°C)
75
100
Figure 5. Supply Current vs. Temperature
125
0
00164-005
SUPPLY CURRENT (µA)
–25
00164-007
0
00164-008
0
00164-004
2
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
LOAD CURRENT (mA)
4.0
4.5
Figure 8. Minimum Input/Output Voltage Differential vs. Load Current
Rev. D | Page 6 of 12
ADR293
120
200
VS = 6V
100
160
RIPPLE REJECTION (dB)
LOAD REGULATION (ppm/mA)
VS = 6V
120
80
IOUT = 5mA
80
60
40
40
20
–25
0
25
50
TEMPERATURE (°C)
75
100
125
0
10
00164-009
0
–50
100
FREQUENCY (Hz)
1k
00164-012
IOUT = 1mA
Figure 12. Ripple Rejection vs. Frequency
Figure 9. Load Regulation vs. Temperature
100
2
VS = 6V
IL = 0mA
TA = +25°C
0
–1
OUTPUT IMPEDANCE (Ω)
∆VOUT FROM NOMINAL (mV)
1
TA = +125°C
TA = –40°C
–2
10
1
SOURCING LOAD CURRENT (mA)
10
1
10
00164-010
–4
0.1
100
1k
FREQUENCY (Hz)
10k
00164-013
–3
Figure 13. Output Impedance vs. Frequency
Figure 10. ΔVOUT from Nominal vs. Load Current
1k
1s/DIV
100
10
100
FREQUENCY (Hz)
1k
Figure 14. 0.1 Hz to 10 Hz Noise
Figure 11. Voltage Noise Density vs. Frequency
Rev. D | Page 7 of 12
00164-014
10µV p-p
00164-011
VOLTAGE NOISE DENSITY (nV/ Hz)
VIN = 15V
TA = 25°C
ADR293
II = 5mA
CL = 1nF
IL = 5mA
5V/DIV
00164-018
50µs/DIV
00164-015
2V/DIV
1ms/DIV
Figure 15. Turn-On Time
Figure 18. Load Transient Response
IL = 5mA
II = 5mA
CL = 100nF
5V/DIV
00164-019
50µs/DIV
00164-016
2V/DIV
1ms/DIV
Figure 16. Turn-Off Time
Figure 19. Load Transient Response
18
TEMPERATURE
+25°C → –40°C →
+85°C → +25°C
16
FREQUENCY IN NUMBER OF UNITS
IL = 5mA
14
12
10
8
6
4
0
–200 –160 –120 –80
Figure 17. Load Transient Response
–40
0
40
80 120
VOUT DEVIATION (ppm)
160
200
Figure 20. Typical Hysteresis for the ADR29x Product
Rev. D | Page 8 of 12
240
00164-020
1ms/DIV
00164-017
2
ADR293
TERMINOLOGY
Line Regulation
The change in output voltage due to a specified change in input
voltage. It includes the effects of self-heating. Line regulation is
expressed in percent per volt, parts per million per volt, or
microvolts per volt change in input voltage.
Load Regulation
The change in output voltage due to a specified change in load
current. It includes the effects of self-heating. Load regulation is
expressed in microvolts per milliampere, parts per million per
milliampere, or ohms of dc output resistance.
Long-Term Stability
Typical shift of output voltage of 25°C on a sample of parts
subjected to high temperature operating life test of 1000 hours
at 125°C.
ΔVOUT = VOUT (t 0 ) − VOUT (t 1 )
ΔVOUT [ppm ] =
VOUT (t 0 ) − VOUT (t 1 )
VOUT (t 0 )
Temperature Coefficient
The change of output voltage over the operating temperature
change and normalized by the output voltage at 25°C, expressed
in ppm/°C.
TCVOUT [ppm/ ° C ] =
VOUT (Τ 2 ) − VOUT (T1 )
VOUT ( 25°C ) × (T2 ) − T1
× 10 6
where:
VOUT (25°C) = VOUT at 25°C.
VOUT (T1) = VOUT at Temperature 1.
VOUT (T2) = VOUT at Temperature 2.
Thermal Hysteresis
Thermal hysteresis is defined as the change of output voltage
after the device is cycled through temperatures from +25°C to
–40°C to +85°C and back to +25°C. This is a typical value from
a sample of parts put through such a cycle.
VOUT − HYS = VOUT ( 25°C ) − VOUT −TC
× 10 6
VOUT − HYS [ppm ] =
where:
VOUT (t0) = VOUT at 25°C at time 0.
VOUT (t1) = VOUT at 25°C after 1000 hours operation at 125°C.
NC = No Connect
There are in fact connections at NC pins, which are reserved for
manufacturing purposes. Users should not connect anything at
NC pins.
VOUT ( 25°C ) − VOUT −TC
VOUT ( 25°C )
× 10 6
where:
VOUT (25°C) = VOUT at 25°C.
VOUT-TC = VOUT (25°C) after temperature cycle at +25°C to –40°C
to +85°C and back to +25°C.
Rev. D | Page 9 of 12
ADR293
THEORY OF OPERATION
The core of the XFET reference consists of two junction field
effect transistors, one of which has an extra channel implant to
raise its pinch-off voltage. By running the two JFETs at the same
drain current, the difference in pinch-off voltage can be amplified
and used to form a highly stable voltage reference. The intrinsic
reference voltage is around 0.5 V with a negative temperature
coefficient of about –120 ppm/K. This slope is essentially locked
to the dielectric constant of silicon and can be closely compensated by adding a correction term generated in the same fashion
as the proportional-to-temperature (PTAT) term used to
compensate band gap references. The big advantage over a band
gap reference is that the intrinsic temperature coefficient is
some 30 times lower (therefore, less correction is needed) and
this results in much lower noise, because most of the noise of a
band gap reference comes from the temperature compensation
circuitry.
The simplified schematic in Figure 21 shows the basic topology
of the ADR293. The temperature correction term is provided by
a current source with value designed to be proportional to
absolute temperature. The general equation is
DEVICE POWER DISSIPATION CONSIDERATIONS
The ADR293 is guaranteed to deliver load currents to 5 mA
with an input voltage that ranges from 5.5 V to 15 V. When
this device is used in applications with large input voltages,
care should be exercised to avoid exceeding the published
specifications for maximum power dissipation or junction
temperature that could result in premature device failure.
The following formula should be used to calculate a device’s
maximum junction temperature or dissipation:
PD =
TJ − TA
θ JA
where:
TJ and TA are the junction temperature and ambient
temperature, respectively.
PD is the device power dissipation.
θJA is the device package thermal resistance.
BASIC VOLTAGE REFERENCE CONNECTIONS
References, in general, require a bypass capacitor connected
from the VOUT pin to the GND pin. The circuit in Figure 22
illustrates the basic configuration for the ADR293. Note that the
decoupling capacitors are not required for circuit stability.
NC 1
⎛ R1 + R2 + R3 ⎞
VOUT = ΔVP ⎜
⎟ + (I PTAT ) ( R3 )
R1
⎝
⎠
2
where:
ΔVP is the difference in pinch-off voltage between the two FETs.
IPTAT is the positive temperature coefficient correction current.
The process used for the XFET reference also features vertical
NPN and PNP transistors, the latter of which are used as output
devices to provide a very low dropout voltage.
VIN
I1
I1
1
VOUT
∆VP
IPTAT
VOUT =
GND
R1 + R2 + R3
× ∆VP + IPTAT × R3
R1
Figure 21. Simplified Schematic
00164-021
R3
1 EXTRA CHANNEL IMPLANT
10µF
0.1µF
NC
7
NC
NC 3
6
4
5
VOUT
0.1µF
NC
NC = NO CONNECT
Figure 22. Basic Voltage Reference Configuration
NOISE PERFORMANCE
The noise generated by the ADR293 is typically less than
15 μV p-p over the 0.1 Hz to 10 Hz band. The noise measurement is made with a band-pass filter made of a 2-pole high-pass
filter with a corner frequency at 0.1 Hz and a 2-pole low-pass
filter with a corner frequency at 10 Hz.
TURN-ON TIME
R1
R2
+
ADR293
8
00164-022
The ADR293 uses a new reference generation technique known
as XFET, which yields a reference with low noise, low supply
current, and very low thermal hysteresis.
Upon application of power (cold start), the time required for
the output voltage to reach its final value within a specified
error band is defined as the turn-on settling time. Two
components normally associated with this are the time for the
active circuits to settle and the time for the thermal gradients on
the chip to stabilize. Figure 15 shows the typical turn-on time
for the ADR293.
Rev. D | Page 10 of 12
ADR293
APPLICATIONS
KELVIN CONNECTIONS
In many portable instrumentation applications where PC board
cost and area go hand-in-hand, circuit interconnects are very often
of dimensionally minimum width. These narrow lines can cause
large voltage drops if the voltage reference is required to provide
load currents to various functions. In fact, a circuit’s interconnects
can exhibit a typical line resistance of 0.45 mΩ/square (1 oz. Cu,
for example). Force and sense connections, also referred to as
Kelvin connections, offer a convenient method of eliminating
the effects of voltage drops in circuit wires. Load currents flowing
through wiring resistance produce an error (VERROR = R × IL) at
the load. However, the Kelvin connection in Figure 23 overcomes
the problem by including the wiring resistance within the forcing
loop of the op amp. Because the op amp senses the load voltage,
op amp loop control forces the output to compensate for the
wiring error and to produce the correct voltage at the load.
2
+VOUT
SENSE
VIN
The ADR293 is ideal for providing a stable, low cost, and low
power reference voltage in portable equipment power supplies.
Figure 24 shows how the ADR293 can be used in a voltage
regulator that not only has low output noise (as compared to
switch mode design) and low power, but also a very fast
recovery after current surges. Some precautions should be taken
in the selection of the output capacitors. Too high an ESR
(effective series resistance) could endanger the stability of the
circuit. A solid tantalum capacitor, 16 V or higher, and an
aluminum electrolytic capacitor, 10 V or higher, are recommended for C1 and C2, respectively. In addition, the path from
the ground side of C1 and C2 to the ground side of R1 should
be kept as short as possible.
CHARGER
INPUT
0.1µF
R3
510kΩ
2
VIN
ADR293
A1
VOUT 6
RLW
ADR293
+VOUT
FORCE
6V
RL
1µF
LEAD-ACID
BATTERY
100kΩ
VOUT 6
2
7
OP20
GND
3
6
IRF9530
4
4
GND
5V, 100mA
00164-025
4
+
R1
402kΩ
1%
Figure 23. Advantage of Kelvin Connection
R2
402kΩ
1%
C1
68µF
TANT
+
+ C2
1000µF
ELECT
Figure 24. Voltage Regulator for Portable Equipment
Rev. D | Page 11 of 12
00164-026
RLW
VIN
VOLTAGE REGULATOR FOR PORTABLE
EQUIPMENT
ADR293
OUTLINE DIMENSIONS
5.00 (0.1968)
4.80 (0.1890)
5
1
6.20 (0.2441)
5.80 (0.2284)
4
1.27 (0.0500)
BSC
0.25 (0.0098)
0.10 (0.0040)
0.51 (0.0201)
0.31 (0.0122)
COPLANARITY
0.10
SEATING
PLANE
0.50 (0.0196)
0.25 (0.0099)
1.75 (0.0688)
1.35 (0.0532)
45°
8°
0°
0.25 (0.0098)
0.17 (0.0067)
1.27 (0.0500)
0.40 (0.0157)
COMPLIANT TO JEDEC STANDARDS MS-012-AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
012407-A
8
4.00 (0.1574)
3.80 (0.1497)
Figure 25. 8-Lead Standard Small Outline Package [SOIC_N]
Narrow Body
(R-8)
Dimensions shown in millimeters and (inches)
3.10
3.00
2.90
8
5
4.50
4.40
4.30
1
6.40 BSC
4
PIN 1
0.65 BSC
0.15
0.05
1.20
MAX
COPLANARITY
0.10
0.30
0.19
SEATING 0.20
PLANE
0.09
8°
0°
0.75
0.60
0.45
COMPLIANT TO JEDEC STANDARDS MO-153-AA
Figure 26. 8-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-8)
Dimensions shown in millimeters
ORDERING GUIDE
Model 1
ADR293ERZ
ADR293ERZ-REEL
ADR293GRZ
ADR293GRZ-REEL7
ADR293GRUZ
ADR293GRUZ-REEL
ADR293GRUZ-REEL7
1
Output
Voltage (V)
5.00
5.00
5.00
5.00
5.00
5.00
5.00
Initial
Accuracy (%)
0.06
0.06
0.20
0.20
0.20
0.20
0.20
Temperature
Coefficient
(ppm/°C max)
8
8
25
25
25
25
25
Temperature
Range
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
Z = RoHS Compliant Part.
©2001-2011 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D00164-0-5/11(D)
Rev. D | Page 12 of 12
Package
Description
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead TSSOP
8-Lead TSSOP
8-Lead TSSOP
Package
Option
R-8
R-8
R-8
R-8
RU-8
RU-8
RU-8
Ordering
Quantity
98
2,500
98
1,000
96
2,500
1,000