Medallion 6000 Series 1550 nm Externally Modulated Transmitter DATASHEET | DECEMBER 2011 FIBER OPTICS The L-type/D-type/S-type/F-type/N-type Medallion 6000 Series Applications High Performance Supertrunking Links High Power Distribution Networks Redundant Ring Architectures FTTx Networks RFOG Applications SAT-IF Transport This product line is a family of state-of-the-art high performance 1550 nm externally modulated CATV fiber optic transmitters optimized for varying network applications. Packaged in convenient 1RU housing, this line of optical transmitters couples high optical output powers, up to 11.0 dBm, with low optical line width resulting in unmatched performance. The optical modulator, combined with proprietary pre-distortion circuitry, provides superior CTB and CSO performance with SBS suppression levels of greater than 21 dBm. Advanced features such as built in field adjustable SBS control and electronic dispersion compensation allow these transmitters to be quickly optimized in the field for any link or application without the need to procure specifically tuned transmitters. This affords the system designer a level of flexibility previously unknown in the CATV market place. The L-type series are designed as a high performance solution for applications where the simultaneous transport of CATV and SAT-IF FM signals is required. The SAT-IF signals can be applied anywhere in the 950 to 2800 MHz band. DWDM Node Splitting Features Single or Dual Optical Outputs QAM Loading to 1003 MHz Dual Power Supplies, Redundant & Hot Swappable Front Panel RF Test Point SNMP Control Interface WEB GUI Vacuum Fluorescent Status Display OMI / RF Gain Adjustment AGC Select: CW, Video, Manual (No AGC) Industry Leading Field Adjustable SBS Suppression Field Adjustable Electronic Dispersion Compensation (EDC) The D-type series are designed as a low cost, high performance solution for applications where the required fiber length is in the range of 20 to 50 kilometers. Advanced, high power, DFB laser technology allows these transmitters to be fielded without the use of EDFAs. The S-type series transmitters are designed to be the most versatile model within the Medallion 6000 series family. They can easily be configured to meet most HFC network solutions requiring link lengths in the range of 50 to 70 kilometers with one EDFA as well as links utilizing multiple EDFA’s. The H-type series transmitters are optimized for single EDFA fiber links in the 70 to 90 kilometer range. These transmitters take advantage of our advanced fiber dispersion compensation circuitry to provide exceptional CATV performance. The F-type series transmitters are intended for use in FTTx and RFoG architecture designs requiring high quality transmission over varying transmission lengths and EDFA output powers. These transmitters successfully support very high optical launch powers while controlling the detrimental effects of Stimulated Brillouin Scattering (SBS), group velocity dispersion (GVD), and self phase modulation (SPM). The N-type series transmitters are intended for use in node-splitting architecture designs requiring cost effective DWDM transmission over medium length fiber distances. | REV 2011.12 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. Medallion 6000 Series 1550 nm Externally Modulated Transmitter FIBER OPTICS DATASHEET | DECEMBER 2011 Optical / Electrical Characteristics L-type Property Performance (Note 1-8) Units 6000-L01 Specified Link Length L (km) Channel Plan Optical Output Power Po (dBm) Models 6000-L02 6000-L03 Comments 6000-L04 25 25 25 25 NTSC 80-Ch PAL 60-Ch NTSC 110-ch PAL 89-Ch 8.5/8.5 8.5/8.5 8.5/8.5 8.5/8.5 With 36 QPSK carriers from 950 to 2800 MHz Min. 10 dBm version avail. See Chart Noise Bandwidth BW (MHz) 4 5 4 5 SBS Suppression (dBm) 15.0 15.0 15.0 15.0 Min. CATV Carrier to Noise Ratio CNR (dB) 51.0 51.0 49.5 49.5 Min. CATV Composite Second Order CSO (dBc) -65 -65 -65 -65 Max. Port 1 CATV Composite Triple Beat CTB (dBc) -65 -65 -65 -65 Max. @ +25C CATV Composite Triple Beat CTB (dBc) -64 -64 -64 -64 Max. @ 0 C to 50 C SAT-IF Carrier to Noise Ratio CNR (dB) 27 27 27 27 Min. SAT-IF Intermodulation Products (dBc) -35 -35 -35 -35 Max. Port 1 SAT-IF Spurious Products (dBc) -38 -38 -38 -38 Max. o o D-type Property Performance (Note 1-7) Specified Link Length Units 6000-D01 L (km) Channel Plan Models 6000-D02 6000-D03 Comments 6000-D04 40 40 40 40 NTSC 80-Ch PAL 60-Ch NTSC 110-ch PAL 89-Ch Optical Output Power Po (dBm) 11.0 11.0 11.0 11.0 Noise Bandwidth BW (MHz) 4 5 4 5 Min. SBS Suppression (dBm) > 12.0 >12.0 >12.0 >12.0 Min. Carrier to Noise Ratio CNR (dB) 54.0 54.0 51.0 51.0 Min. Composite Second Order CSO (dBc) -65 -65 -65 -65 Max. Composite Triple Beat CTB (dBc) -65 -65 -65 -65 Max. @ +25C Composite Triple Beat CTB (dBc) -64 -64 -64 -64 Max. @ 0 C to 50 C o o S-type Property Performance (Note 1-7) Specified Link Length Units 6000-SA1 L (km) Channel Plan Optical Output Power Po (dBm) 6000-SA2 Models 6000-SA3 Comments 6000-SA4 6000-SA5 65 65 65 65 65 NTSC 80 PAL 60 NTSC 110 PAL 89 42 CENELEC 7.0/ 7.0 7.0/ 7.0 7.0/ 7.0 7.0/ 7.0 7.0/ 7.0 Min. - Higher Powers Available Noise Bandwidth BW (MHz) 4 5 4 5 5 SBS Suppression (dBm) 16.0 16.0 16.0 16.0 16.0 Min. Min. Carrier to Noise Ratio CNR (dB) 53.0/ 53.0 53.0/ 53.0 50.0/ 50.0 50.0/ 50.0 53.0/ 53.0 Composite Second Order CSO (dBc) -65/ -65 -65/ -65 -65/ -65 -65/ -65 -65/ -65 Max. Composite Triple Beat CTB (dBc) -65 -65 -65 -65 -65 Composite Triple Beat CTB (dBc) -64 -64 -64 -64 -64 Max. @ +25C o Max. @ 0 C to o 50 C | REV 2011.12 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. Medallion 6000 Series 1550 nm Externally Modulated Transmitter FIBER OPTICS DATASHEET | DECEMBER 2011 H-type Property Performance (Note 1-7) Units Specified Link Length Models 6000-H01 6000-H02 L (km) Channel Plan Optical Output Power Po (dBm) 80 80 NTSC 80-Ch PAL 60-Ch 7.0/ 7.0 7.0/ 7.0 Comments Min. Noise Bandwidth BW (MHz) 4 5 SBS Suppression (dBm) 18.0 18.0 Carrier to Noise Ratio CNR (dB) 52.0/ 52.0 52.0/ 52.0 Min. Composite Second Order CSO (dBc) -65/ -65 -65/ -65 Max. Min. Composite Triple Beat CTB (dBc) -65 -65 Max. @ +25C Composite Triple Beat CTB (dBc) -64 -64 Max. @ 0 C to 50 C o o F-type Property Performance (Note 1-7) Specified Link Length Units 6000-F01 L (km) Channel Plan 6000-F02 Models 6000-F03 Comments 6000-F04 20 20 20 20 PAL 89-Ch NTSC 80-Ch PAL 60-Ch NTSC 110-ch Optical Output Power Po (dBm) 7.0/ 7.0 7.0/ 7.0 7.0/ 7.0 7.0/ 7.0 Noise Bandwidth BW (MHz) 4 5 4 5 SBS Suppression (dBm) 21.0 21.0 21.0 21.0 Min. Carrier to Noise Ratio CNR (dB) 48.0 48.0 45.0 45.0 Min. Composite Second Order CSO (dBc) -58 -58 -58 -58 Max. Composite Triple Beat CTB (dBc) -58 -58 -58 -58 Max. Min. N-type Property Performance (Note 1-7) Specified Link Length Units L (km) Channel Plan Models 6000-N01 6000-N02 40 40 NTSC 80-Ch PAL 60-Ch Comments Optical Output Power Po (dBm) 9.5 9.5 Noise Bandwidth BW (MHz) 4 5 Min. SBS Suppression (dBm) 13.0 13.0 Min. Min. Carrier to Noise Ratio CNR (dB) 52.0 52.0 Composite Second Order CSO (dBc) -62 -62 Max. Composite Triple Beat CTB (dBc) -62 -62 Max. @ +25C Composite Triple Beat CTB (dBc) -61 -61 Max. @ 0 C to 50 C o o Notes: 1. Unless stated otherwise all specifications apply over full temperature range with no digital loading. 2. Unless stated otherwise specifications apply for nominal RF input level as defined below, after a 30 minute stabilization period. 3. Specifications separated by a slash are port1 / port 2. 4. Units are tested per the Test / Link Configuration Table 5. Noise figure for the EDFA = 4.5 ~ 5.5 dB 6. Corning SMF-28 single mode fiber 7. Receiver responsivity is 0.95 mA/mW, Equivalent noise current is 7 pA/(Hz)1/2 8. With 36 QPSK modulated SAT-IF signals between 950 … 2800 MHz. 27 MHz IF bandwidth | REV 2011.12 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. Medallion 6000 Series 1550 nm Externally Modulated Transmitter FIBER OPTICS DATASHEET | DECEMBER 2011 General and Mechanical Specifications Property Requirement Comments Various Options + ITU-grid available – see Model Number Information Custom channel plans available Wavelength 1550 +/-5 nm Channel Plan Various – See Specification Tabels Optical Connector Monitoring Interfaces SC/APC 100 Base-T Ethernet (SNMP) Rear Panel RS-232 interface VFD Screen Front Panel Controls Operating Temperature 0C to 50C Storage Temperature Transportation Vibration -20C to 70C 65W max EMI: EN50083-2:2006 (US CATV) EN55022:2006 (US IT) EN61000-3-2 (Harmonics) EN61000-3-3 (Flicker) FCC: Part 15, Subpart B, class “A” Unintentional Radiators ICES-003 (Canada) AN/NZS 3548, Class A (Australia) VCCI, Class A (Japan) GR-2853-CORE Transportation Shock GR-2853-CORE In Shipping package 20% to 85% 90 to 265 VAC, 50/60 Hz Non-condensing Power Consumption Agency Listings Operating Humidity Supply Range (VAC) (VDC) VFD- (Vacuum Fluorescent Display) Safety: FDA/CDRH Laser Safety Governed by Code of Federal Regulations Title 21, Volume 8, Part 1040 IEC 60950-1 IEC 60728-11 Laser IEC 60825-1 CB Certification In Shipping package +/- (36 – 72) VDC Dimensions 19.0”W x 15.0”D x 1.72”H Input Power Range 17 +/-1 dBmV/ch 80 NTSC channels 15 +/-1 dBmV/ch 110 NTSC channels 18 +/-1 dBmV/ch 60 PAL channels 20 +/-1 dBmV/ch 42 CENELEC channels 16 +/-1 dBmV/ch 89 PAL channels 27 +/-1 dBmV/ch SAT-IF channels 19 +/-2 dBmV/ch 80 NTSC channels 17 +/-2 dBmV/ch 110 NTSC channels 20 +/-2 dBmV/ch 60 PAL channels 18 +/-2 dBmV/ch 89 PAL channels 22 +/-2 dBmV/ch 42 CENELEC channels 29 +/-2 dBmV/ch SAT-IF channels Input Power Range Other styles available (width includes 19” front panel ears, depth includes, connectors, fans & front panel) – see drawing Manual mode Manual mode Manual mode Manual mode Manual mode Manual mode CW mode CW mode CW mode CW mode CW mode AGC mode | REV 2011.12 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. Medallion 6000 Series 1550 nm Externally Modulated Transmitter FIBER OPTICS DATASHEET | DECEMBER 2011 General and Mechanical Specifications (continued) Property Requirement Front Panel RF Gain / OMI Adjustment Range Comments +2 / -4 dB from nominal setting CATV Performance can vary slightly CATV Frequency Range 45MHz – 1003 MHz CATV Flatness +/- 0.50 dB +/- 0.75 dB 45MHz – 1003 MHz CATV Flatness – N-Type +/- 0.75 dB 45MHz – 1003 MHz N-Type CATV Input impedance 75 CATV Input Return Loss 16dB min CATV Front Panel RF Tap -20 +/- 1 dB down from RF input CATV Front Panel RF Tap Flatness +/- 1 dB SAT-IF Frequency Range 950MHz – 2800 MHz SAT-IF Flatness +/- 2 dB SAT-IF Input impedance 75 SAT-IF Input Return Loss 10dB min SAT-IF Front Panel RF Tap 7 +/- 2.5 dBmV/Ch at 1% OMI/ch SAT-IF Front Panel RF Tap Flatness +/- 1 dB 45MHz - 550MHz 45MHz – 1003 MHz 45MHz – 1003 MHz 950MHz – 2800 MHz 950MHz – 2800 MHz Test/Link Configuration Property Link1 EDFA Received Power2 L-Type 15 dBm 25 Km 0.0 dBm at the receiver D-Type None 40 Km 0.0 dBm at the receiver S-Type 16 dBm 65 Km 0.0 dBm at the receiver H-Type 18 dBm 80 Km 0.0 dBm at the receiver F-Type 21 dBm 20 Km -5.5 dBm at the receiver N-Type 13 dBm 40 Km 0.0 dBm at the receiver | REV 2011.12 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. Medallion 6000 Series 1550 nm Externally Modulated Transmitter DATASHEET | DECEMBER 2011 FIBER OPTICS Outline Drawing (Dimensions in inches) Laser Safety Information This product meets the applicable requirements of 21 CFR 1010 & 1040 and is classified as a class 1M laser product. During use as intended, the laser energy is fully contained within the fiber network such that there is no accessible laser radiation. This product has been issued accession number 0820466-001. | REV 2011.12 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. Medallion 6000 Series 1550 nm Externally Modulated Transmitter FIBER OPTICS DATASHEET | DECEMBER 2011 Model Number Information (note 3) 6000 – □□□ □-□ □□□□ Logo & Customer Specific Link type 0 – EMCORE Logo 1 – no Logo Pout (dBm min) Note 1 Loading Type Optics D – 40 km 0 – for D, H, and F types 1 – NTSC (80ch) 1 – SC/APC, Rear S – 65 km A – 7.0/7.0 for Stype 2 – PAL (60-ch) 2 – FC/APC, Rear H – 80 km B – 8.0/8.0 for S Type 3 – NTSC (110ch) 3– E2000/APC, Rear F – FTTx SBS 20 dBm C – 10.0 for S Type 4 – PAL (89-ch) 4 – SC/APC, Front L – 25 km D– 10 / 10 for S and L Note 4 Type 5 – Not Used 5 – FC/APC, Front N – 40 km E – 8.5/8.5 for L Type 6 – CENELEC (42-ch) 6– E2000/APC, Front Note 5 RF 1 – RF IN Rear, TP Front 2 – RF IN Front, TP Front 3 – RF IN Front, TP Rear 4 – RF IN Rear, TP Rear Wavelength (nm) Power Supply 00 –1555+/5.0nm 1 – AC primary, no secondary 01 – 1550+/5.0nm 2 – DC primary, no secondary xx – ITU Channel +/Note 2 0.1nm 3 – AC primary, AC secondary 4 – AC primary, DC secondary 5 – DC primary, DC secondary Note 1: Options available for Indicated Types only. Note 2: ITU grid wavelengths can be specified from channel 18 to 40. Note 3: Not all configurations are available, contact factory. Note 4: Available for S and L Links. CSO port 2 degraded by 1dB for Channel Loads 1 and 2, CSO port 2 degraded by 2dB for Channel Loads 3 and 4. Note 5: Contact Factory for Model type availability Additional Kits G3708-006-001 - Replaceable AC power supply modules G3708-005-001 - Replaceable DC power supply modules G7914-076-001 - Replaceable Blank power module plate G7906-008-001 - Replaceable fans | REV 2011.12 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.