J-Type Medallion 6000 1550 nm Externally-Modulated Transmitter DATASHEET | OCTOBER 2013 FIBER OPTICS The J-Type Medallion 6000 Series Applications High-Performance Supertrunking Links High-Power Distribution Networks Redundant Ring Architectures FTTx Networks RFOG Applications SAT-IF Transport This product line is a family of state-of-the-art high performance 1550 nm externally-modulated CATV fiber optic transmitters optimized for varying network applications. Packaged in convenient 1RU housing, this line of optical transmitters couples high optical output power, up to 10.0 dBm, with low optical line width resulting in unmatched performance. The optical modulator, combined with proprietary pre-distortion circuitry, provides superior CTB and CSO performance with SBS suppression levels of greater than 17 dBm for SAT-IF applications. Advanced features such as built in field adjustable SBS control allow these transmitters to be quickly optimized in the field for any link or application without the need to procure specifically tuned transmitters. This affords the system designer a level of flexibility previously unknown in the CATV market place. The J-Type series are designed as a high-performance solution for applications where the simultaneous transport of CATV and SAT-IF FM signals is required. The SAT-IF signals can be applied anywhere in the 950 to 2800 MHz band. DWDM Node Splitting Features Single or Dual Optical Outputs QAM Loading to 1003 MHz J-Type transmitters are specially designed and optimized to support optical fiber links of up to 150kms for the Japanese market place. SAT-IF Loading from 950 to 2800 MHz Dual Power Supplies, Redundant & Hot Swappable Front Panel RF Test Point Vacuum Fluorescent Status Display OMI / RF Gain Adjustment AGC Select: CW, Video, Manual (No AGC) Industry Leading Field Adjustable SBS Suppression | REV 2013.10 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. J-Type Medallion 6000 1550 nm Externally-Modulated Transmitter FIBER OPTICS DATASHEET | OCTOBER 2013 Optical Characteristics Property Performance (note 1-8) Units 6000-0JE1 Specified Link Length L (km) Channel Plan 25 NTSC 20+ 60-64 QAM Models 6000-0JE2 6000-0JE3 25 25 NTSC 80-Ch PAL 60-Ch 8.5/8.5 8.5/8.5 8.5/8.5 Comments With 36 QPSK carriers from 950 to 2800 MHz Min. 10 dBm version avail. See Chart Optical Output Power Po (dBm) Noise Bandwidth BW (MHz) 4 4 5 SBS Suppression (dBm) 11 to 17 11 to 17 11 to 17 CATV Carrier to Noise Ratio CNR (dB) 58.5 51.0 51.0 Min. CATV Composite Second Order CSO (dBc) -67 -65 -65 Max. Port 1 Min. CATV Composite Triple Beat CTB (dBc) -67 -65 -65 Max. @ +25°C CATV Composite Triple Beat CTB (dBc) -66 -64 -64 Max. @ 0 C to 50 C SAT-IF Carrier to Noise Ratio o CNR (dB) 27 27 27 Min. SAT-IF Intermodulation Products (dBc) -35 -35 -35 Max. Port 1 SAT-IF Spurious Products (dBc) -38 -38 -38 Max. o Notes: 1. Unless stated otherwise all specifications apply over full temperature range with no digital loading. 2. Unless stated otherwise specifications apply for nominal RF input level as defined below, after a 30 minute stabilization period. 3. Specifications separated by a slash are port1 / port 2. 4. Units are tested per the Test / Link Configuration Table 5. Noise figure for the EDFA = 4.5 ~ 5.5 dB 6. Corning SMF-28 single mode fiber 7. Receiver responsivity is 0.95 mA/mW, Equivalent noise current is 7 pA/(Hz)1/2 8. With 36 QPSK modulated SAT-IF signals between 950 … 2800 MHz. 27 MHz IF bandwidth Test/Link Configuration Property J-Type EDFA Link Received Power2 14 dBm 25 Km 0.0 dBm at the receiver | REV 2013.10 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. J-Type Medallion 6000 1550 nm Externally-Modulated Transmitter FIBER OPTICS DATASHEET | OCTOBER 2013 Electrical Specifications Property CATV Nominal Input Power CATV Composite Level CATV Input Range CATV RF Gain / OMI Adjustment Range CATV Frequency Range Requirement Comments 23 dBmV/ch (84 dBuV/ch) 18 dBmV/ch (78 dBuV/ch) 19 dBmV/ch (79 dBuV/ch) 20 NTSC channels + 60 QAM at -10 dB 80 NTSC channels 60 PAL channels -11.7 dBm O dB on FP Display (All Channel Plans) +2/-8 dB from nominal input Optimal performance at nominal input +2/-8 dB from nominal setting CATV Performance may vary slightly over range 45 MHz – 1003 MHz CATV Flatness +/- 0.50 dB 45 MHz – 550 MHz +/- 0.75 dB 45 MHz – 1003 MHz CATV Input impedance 75Ω CATV Input Return Loss 16 dB min CATV Front Panel RF Tap -20 +/- 1 dB down from RF input CATV Front Panel RF Tap Flatness +/- 1 dB SAT Nominal Input Power SAT Input Range 45 MHz – 1003 MHz 45 MHz – 1003 MHz 27 dBmV/ch (87 dBuV/ch) 36 QPSK SAT-IF channels 22 – 32 dBmV/ch (82 – 92 dBuV/ch) Optimum performance at nominal input -6.2 dBm 0 dB on FP Display +5 / -5 dB from nominal setting CATV Performance can vary slightly SAT Composite Level SAT-IF RF Gain / OMI Adjustment Range SAT-IF Frequency Range 950 MHz – 2800 MHz SAT-IF Flatness +/- 2 dB SAT-IF Input impedance 75Ω SAT-IF Input Return Loss SAT-IF Front Panel RF Tap 10 dB min 950 MHz – 2800 MHz 7 +/- 2.5 dBmV/Ch at Nominal OMI/ch SAT-IF Front Panel RF Tap Flatness +/- 1 dB 950 MHz – 2800 MHz General and Mechanical Specifications Property Requirement Wavelength 1555+/-5 nm Channel Plan Various – See Specification Tables Optical Connector SC/APC 100 Base-T Ethernet (SNMP) Rear Panel RS-232 interface VFD Screen Front Panel Controls Monitoring Interfaces Operating Temperature Comments Various Options + ITU-grid available – see Model Number Information Custom channel plans available Other styles available VFD- (Vacuum Fluorescent Display) 0°C to 50°C Storage Temperature -20°C to 70°C 65 W max Power Consumption | REV 2013.10 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. J-Type Medallion 6000 1550 nm Externally-Modulated Transmitter FIBER OPTICS DATASHEET | OCTOBER 2013 General and Mechanical Specifications (continued) Property Agency Listings Requirement Comments EMI: EN50083-2:2006 (US CATV) EN55022:2006 (US IT) EN61000-3-2 (Harmonics) EN61000-3-3 (Flicker) FCC: Part 15, Subpart B, class “A” Unintentional Radiators ICES-003 (Canada) AN/NZS 3548, Class A (Australia) VCCI, Class A (Japan) Safety: FDA/CDRH Laser Safety Governed by Code of Federal Regulations Title 21, Volume 8, Part 1040 IEC 60950-1 IEC 60728-11 Laser IEC 60825-1 CB Certification Transportation Vibration GR-2853-CORE In Shipping package Transportation Shock GR-2853-CORE In Shipping package 20% to 85% Non-condensing Operating Humidity Supply Range 90 to 265 VAC, 50/60 Hz +/- (36 – 72) VDC (VAC) (VDC) Dimensions 19.0” W x 15.0” D x 1.72” H (width includes 19” front panel ears, depth includes, connectors, fans & front panel) – see drawing Outline Drawing | REV 2013.10 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. J-Type Medallion 6000 1550 nm Externally-Modulated Transmitter FIBER OPTICS DATASHEET | OCTOBER 2013 Model Number InformationNote 3 6000 – □□□ □-□ □□□□ Logo & Customer Specific Link Type 0 – EMCORE Logo J – 25 km Pout (dBm min) Note 1 1 – no Logo D – 10/10 Note 4 E – 8.5/8.5 Loading Type Optics 1 – NTSC (20-ch) + 60 64QAM 1 – SC/APC, Rear 2 – NTSC (80-ch) 2 – FC/APC, Rear 3 – PAL (60-ch) 3 – E2000/APC, Rear 4 – SC/APC, Front 5 – FC/APC, Front RF 1 – RF IN Rear, TP Front 2 – RF IN Front, TP Front 3 – RF IN Front, TP Rear 4 – RF IN Rear, TP Rear Wavelength (nm) Power Supply 00 –1555+/5.0 nm 1 – AC primary, no secondary 01 – 1550+/5.0 nm 2 – DC primary, no secondary xx – ITU Channel +/Note 2 0.1 nm 3 – AC primary, AC secondary 4 – AC primary, DC secondary 5 – DC primary, DC secondary 6 – E2000/APC, Front Note 1: Options available for Indicated Types only. Note 2: ITU grid wavelengths can be specified from channel 18 to 40. Note 3: Not all configurations are available, contact factory. Note 4: CSO port 2 degraded by 1dB Note 5: Contact Factory for Model type availability Additional Kits G3708-006-001 - Replaceable AC power supply modules G3708-005-001 - Replaceable DC power supply modules G7914-076-001 - Replaceable Blank power module plate G3906-008-001 - Replaceable fans Laser Safety Information This product meets the applicable requirements of 21 CFR 1010 & 1040 and is classified as a class 1M laser product. During use as intended, the laser energy is fully contained within the fiber network such that there is no accessible laser radiation. This product has been issued accession number 0820466-001. | REV 2013.10 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.