Optiva OTS-2 C-Band RF Fiber Optic Links DATASHEET | OCTOBER 2013 SATCOM The Optiva OTS-2 C-Band transmitter and receiver are ideal to construct downlink 3.400 to 4.200 GHz and uplink 5.850 to 6.725 GHz transparent fiber optic links for antenna remoting, electronic warfare systems, broadband delay lines, signal processing systems and other high-dynamic-range applications. Optiva satellite and microwave transmitters and receivers are SNMP compliant. They can be housed in the same chassis and monitored by the same Network Management System (NMS) as Optiva HD video, audio, serial data, and USB extension / distribution cards to provide multiple format and frequency Applications transport in a single flexible platform. Satcom C-Band Antenna Signal Distribution System Design Ground Terminal & Intra-Facility Links The Optiva platform includes a wide range fiber Site Diversity Systems Electronic Warfare (EW) Systems optic transport products for satellite and microwave communications from 1 MHz to 40 GHz. These units can be used to construct transparent inter- and intra-facility links from 1 meter to >100 km for RF and Broadband Delay Line and Signal Processing Systems microwave signal transport, antenna remoting, video transport, electronic Features / Benefits Optiva is a completely modular, hot-swappable platform. Both 19” rack-mount C-Band Uplink and Downlink - Eliminates the performance and cost penalty of block up/ down conversion warfare systems and other high-dynamic-range applications. and compact tabletop, or wall-mountable enclosures are available. The 3 RU 19” rack-mount, fan-cooled enclosures (Model OT-CC-16 and OT-CC-16F) can support up to 16 insert cards and utilize two dual-redundant, hot-swappable, 100 or 200 Low RIN Source Laser - Provides highdynamic-range of >102 dB Hz2/3 watt power supplies. The 1 RU 19” rack-mount, fan-cooled enclosure (Model: OT- Microprocessor-Based Transmitter Control for Laser Bias, Modulator Bias & Link Gain - Provides consistent high performance operation and allows for modulator low-bias operation and SFDR >102 dB Hz2/3 power supplies. Compact one-slot (OT-DTCR-1), or two-slot (OT-DTCR-2) enclosures SNMP V.1 and RS-232 Monitor & Control Interface - Flexible user interface options Compatible with EMCORE’s Modular Optiva Platform - Allows multiple format and frequency transport in a single chassis DWDM Operation - Increases transport capacity without increasing fiber count CC-6-1U) can accommodate 6 insert cards and utilizes two hot-swappable 60 watt are also available that use an external wall-mount power supply. Block Diagram Transmitter Receiver Externally Modulated Transmitter RF in Variable Gain RF Preamp Laser/Modulator Microprocessor Control -20 dB RF Test Point © 2013 EMCORE Corporation | REV 2013.10 PL +1 626-293-3400 Optical Output +10 dBmo min PR RFout Photodiode Optical Preamp/Rx Microprocessor Control Variable Gain RF Postamp Optical Input +11.8 dBmo max [email protected] -20 dB RF Test Point www.emcore.com Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice. Optiva OTS-2 C-Band RF Fiber Optic Links DATASHEET | OCTOBER 2013 SATCOM Performance Highlights Parameter Frequency Range RF Input Power Min Typical Max Units 3.400 - 4.200 GHz 5.850 - 6.725 GHz - - 5* dBm Typical C-Band Downlink S21 Frequency Response -15^ Wavelength Optical Output Power Operating Temperature Range - 1550 - nm 9 10 11 dBmo -10 - 50 °C *Tx: RF amp 15 dB gain, attenuation range 0 to 15 dB ^Tx: RF amp 35 dB gain, attenuation range 0 to 15 dB Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of the datasheet. Exposure to absolute maximum ratings for extended periods can adversely affect device reliability. Symbol Min Max Units Operating Temperature Parameter TOP -20 60 °C Storage Temperature TSTG -40 85 °C RF Input Sin NA 5* dBm Typical C-Band Uplink S21 Frequency Response -15^ *Tx: RF amp 15 dB gain ^Tx: RF amp 35 dB gain Environmental Specifications Parameter Operating Temperature Operating Humidity, Maximum Non-Condensing Operating Altitude, Above Sea Level Symbol Min Max Units TOP -10 50 °C -- -- 95% -- -- 6000 ft 1828.8 m TSTG -40 70 °C Storage Humidity, Maximum Non-Condensing -- -- 95% -- Storage Altitude, Above Sea Level -- -- 50,000 ft 15,240 m Storage Temperature © 2013 EMCORE Corporation | REV 2013.10 +1 626-293-3400 Enclosure Options [email protected] www.emcore.com Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice. Optiva OTS-2 C-Band RF Fiber Optic Links DATASHEET | OCTOBER 2013 SATCOM Transmitter & Receiver Optical Characteristics Symbol Condition Min Typical Max Units Wavelength Parameter l - 1530 1550 1562 nm Optical Output Power PL - 9 10 11 dBmo Connector Return Loss - - 40 - - dB Optical Connector Type - SC/APC - - - - Pin - - - +10 dBmo - - 0.7 - - A/W Receiver Optical Input Power Receiver Responsivity Note: In order to prevent reflection-induced distortion degradation, the laser should be connected to an optical cable having a return loss of at least 55 dB for discrete reflections and 30 dB for distributed reflections. C-Band Transmitter & Receiver RF Characteristics Parameter Condition Min Typical Max Units Operational Bandwidth - 3.400 5.850 - 4.200 6.725 GHz GHz RF Input Impedance - - 50 - Ω RF Return Loss - - - -15 dB - -18 -22 dB RF Connectors SMA Female RF Test Point Reference Value, Relative to RF input or RF output* -20 *Test point performance beyond the stated frequency range is provided; only the test point reference value tolerance may increase beyond the above stated +/- 1 dB DC Power Consumption - Max Input Voltage (VDC) Max Current (@+70°C) Transmitter Module Type +12 1A Receiver +12 750 mA Network Management All modules are compliant with SNMP v.1 supported through the Optiva NMS card (OPV-CTLR-IC) © 2013 EMCORE Corporation | REV 2013.10 +1 626-293-3400 [email protected] www.emcore.com Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice. Optiva OTS-2 C-Band RF Fiber Optic Links DATASHEET | OCTOBER 2013 SATCOM Link Performance - C-Band Downlink Symbol Condition Min Typical Max Units RF Bandwidth Parameter - - 3.400 - 4.200 GHz Link Gain (+0 dBmo Rx optical input)*^ G @ 3.400 GHz 0 4 - dB G @ 4.200 GHz 0 4 - dB G @ 3.400 GHz 20 24 - dB G @ 4.200 GHz 20 24 - dB NF @ 3.400 GHz 12 - - dB NF @ 4.200 GHz 12 - - dB NF @ 3.400 GHz 7 - - dB NF @ 4.200 GHz 7 - - dB IIP3 @ 3.400 GHz - -6 - dBm Link Gain (+10 dBmo Rx optical input)*^ Noise Figure (+0 dBmo Rx optical input)^ Noise Figure (+10 dBmo Rx optical input)^ Input IP3^ Spurious Free Dynamic Range^ Gain Variation IIP3 @ 4.200 GHz - -5 - dBm SFDR @ 0 dBmo Rx Optical Input 101 - - dB-Hz2/3 SFDR @ +10 dBmo Rx Optical Input 105 - - dB-Hz2/3 - Any 36 MHz - - 0.5 dB - Any 500 MHz - - 1.5 dB *Receiver RF output will change 2 dB for each 1 dB of Rx optical input power level change ^Performance based on OTS-2T/S5 with RF Amp gain of 35 dB, OTS-2R/S5 with RF Amp gain of 15 dB Link Performance - C-Band Uplink Symbol Condition Min Typical Max Units RF Bandwidth Parameter - - 5.850 - 6.725 GHz Link Gain (+0 dBmo Rx optical input)*^ G @ 5.850 GHz -2 2 - dB G @ 6.725 GHz -2 2 - dB G @ 5.850 GHz 18 22 - dB G @ 6.725 GHz 18 22 - dB NF @ 5.850 GHz 12 - - dB NF @ 6.725 GHz 12 - - dB NF @ 5.850 GHz 7 - - dB NF @ 6.725 GHz 7 - - dB IIP3 @ 5.850 GHz - -6 - dBm IIP3 @ 6.725 GHz - -5 - dBm SFDR @ 0 dBmo Rx Optical Input 101 - -- dB-Hz2/3 SFDR @ +10 dBmo Rx Optical Input 105 - -- dB-Hz2/3 - Any 36 MHz - - 0.5 dB P-P - Any 500 MHz - - 1.5 dB P-P Link Gain (+10 dBmo Rx optical input)*^ Noise Figure (+0 dBmo Rx optical input)^ Noise Figure (+10 dBmo Rx optical input)^ Input IP3^ Spurious Free Dynamic Range^ Gain Variation *Receiver RF output will change 2 dB for each 1 dB of RX optical input power level change ^Performance based on OTS-2T/S5 with RF Amp gain of 35 dB, OTS-2R/S5 with RF Amp gain of 15 dB © 2013 EMCORE Corporation | REV 2013.10 +1 626-293-3400 [email protected] www.emcore.com Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice. Optiva OTS-2 C-Band RF Fiber Optic Links DATASHEET | OCTOBER 2013 SATCOM Ordering Information: Transmitter Transmitter OTS-2T / S5-VVVV-WW-10-XX-12-YY-Z When ordering replace “VVVV” with one of the C-Band Frequency Options When ordering replace “WW” with one of the ITU Channel Options When ordering replace “XX” with one of the Optical Connector Options When ordering replace “YY” with one of the Variable Gain RF Amplifier Options When ordering replace “Z” with one of the Enclosure Options RF Connector C-Band Frequency Options (GHz) “VVVV” ITU Channel Options (THz / nm) “WW” S5 = 50 Ω SMA 3442 = 3.400-4.200 GHz Uplink Standard: 00 = non-ITU: 1520-1580 nm 5867 = 5.850-6.725 GHz Downlink Optional: 18 = 191.8 THz/1563.05 nm 19 = 191.9 THz/1562.23 nm 20 = 192 THz/1561.42 nm 21 = 192.1 THz/1560.61 nm 22 = 192.2 THz/1559.79 nm 23 = 192.3 THz/1558.98 nm 24 = 192.4 THz/1558.17 nm 25 = 192.5 THz/1557.36 nm 26 = 192.6 THz/1556.56 nm 27 = 192.7 THz/1555.75 nm 28 = 192.8 THz/1554.94 nm 29 = 192.9 THz/1554.13 nm 30 = 193 THz/1553.33 nm 31 = 193.1 THz/1552.52 nm 32 = 193.2 THz/1551.72 nm 33 = 193.3 THz/1550.92 nm 34 = 193.4 THz/1550.12 nm 35 = 193.5 THz/1549.32 nm 36 = 193.6 THz/1548.51 nm 37 = 193.7 THz/1547.72 nm 38 = 193.8 THz/1546.92 nm 39 = 193.9 THz/1546.12 nm 40 = 194 THz/1545.32 nm 41 = 194.1 THz/1544.53 nm 42 = 194.2 THz/1543.73 nm 43 = 194.3 THz/1542.94 nm 44 = 194.4 THz/1542.14 nm 45 = 194.5 THz/1541.35 nm 46 = 194.6 THz/1540.56 nm 47 = 194.7 THz/1539.77 nm 48 = 194.8 THz/1538.98 nm 49 = 194.9 THz/1538.19 nm 50 = 195 THz/1537.4 nm 51 = 195.1 THz/1536.61 nm 52 = 195.2 THz/1535.82 nm 53 = 195.3 THz/1535.04 nm 54 = 195.4 THz/1534.25 nm 55 = 195.5 THz/1533.46 nm 56 = 195.6 THz/1532.68 nm 57 = 195.7 THz/1531.9 nm 58 = 195.8 THz/1531.12 nm 59 = 195.9 THz/1530.33 nm 60 = 196 THz/1529.55 nm 61 = 196.1 THz/1528.77 nm 62 = 196.2 THz/1527.99 nm Optical Power (dBmo) Optical Connector Options “XX” 10 = +10 Optical Output Standard: SA = SC / APC Optical Output + RF Test Port (dB) 1 = Single Optical Output + 2 = -20 dB Test Port Variable Gain RF Amplifier Options (dB) “YY” 15 = 15 dB 35 = 35 dB © 2013 EMCORE Corporation | REV 2013.10 Optional: FA = FC / APC EA = E2000 / APC +1 626-293-3400 Enclosure Options “Z” 1 = Optiva Indoor Rack-Mount Installation 2 = Optiva Outdoor MiniHub Installation [email protected] www.emcore.com Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice. Optiva OTS-2 C-Band RF Fiber Optic Links DATASHEET | OCTOBER 2013 SATCOM Ordering Information: Receiver Receiver OTS-2R / S5-VVVV-10-WW-XX-2-YY-Z When ordering replace “VVVV” with one of the C-Band Frequency Options When ordering replace “WW” with one of the Optical Connector Options When ordering replace “XX” with one of the ITU Channel Options When ordering replace “YY” with one of the Variable Gain RF Amplifier Options When ordering replace “Z” with one of the Enclosure Options RF Connector S5 = 50 Ω SMA C-Band Frequency Options (GHz) “VVVV” 3442 = 3.400-4.200 GHz Uplink Optical Power (dBmo) 10 = +10 Max Optical Input Optical Connector Options “WW” ITU Filter Options for Improved Optical Isolation in DWDM Systems (THz / nm) “XX” Test Port (dB) Standard: SA = SC / APC Standard: 00 = No filter 2 = -20 dB Test Port Optional: FA = FC / APC EA = E2000 / APC Optional: 18 = 191.8 THz/1563.05 nm 19 = 191.9 THz/1562.23 nm 20 = 192 THz/1561.42 nm 21 = 192.1 THz/1560.61 nm 22 = 192.2 THz/1559.79 nm 23 = 192.3 THz/1558.98 nm 24 = 192.4 THz/1558.17 nm 25 = 192.5 THz/1557.36 nm 26 = 192.6 THz/1556.56 nm 27 = 192.7 THz/1555.75 nm 28 = 192.8 THz/1554.94 nm 29 = 192.9 THz/1554.13 nm 30 = 193 THz/1553.33 nm 31 = 193.1 THz/1552.52 nm 32 = 193.2 THz/1551.72 nm 33 = 193.3 THz/1550.92 nm 34 = 193.4 THz/1550.12 nm 35 = 193.5 THz/1549.32 nm 36 = 193.6 THz/1548.51 nm 37 = 193.7 THz/1547.72 nm 38 = 193.8 THz/1546.92 nm 39 = 193.9 THz/1546.12 nm 40 = 194 THz/1545.32 nm 41 = 194.1 THz/1544.53 nm 42 = 194.2 THz/1543.73 nm 43 = 194.3 THz/1542.94 nm 44 = 194.4 THz/1542.14 nm 45 = 194.5 THz/1541.35 nm 46 = 194.6 THz/1540.56 nm 47 = 194.7 THz/1539.77 nm 48 = 194.8 THz/1538.98 nm 49 = 194.9 THz/1538.19 nm 50 = 195 THz/1537.4 nm 51 = 195.1 THz/1536.61 nm 52 = 195.2 THz/1535.82 nm 53 = 195.3 THz/1535.04 nm 54 = 195.4 THz/1534.25 nm 55 = 195.5 THz/1533.46 nm 56 = 195.6 THz/1532.68 nm 57 = 195.7 THz/1531.9 nm 58 = 195.8 THz/1531.12 nm 59 = 195.9 THz/1530.33 nm 60 = 196 THz/1529.55 nm 61 = 196.1 THz/1528.77 nm 62 = 196.2 THz/1527.99 nm Variable Gain RF Amplifier Options (dB) “YY” 15 = 15 dB Enclosure Options “Z” 1 = Optiva Indoor RackMount Installation 35 = 35 dB 5867 = 5.850-6.725 GHz Downlink © 2013 EMCORE Corporation | REV 2013.10 +1 626-293-3400 [email protected] 2 = Optiva Outdoor MiniHub Installation www.emcore.com Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice. Optiva OTS-2 C-Band RF Fiber Optic Links DATASHEET | OCTOBER 2013 SATCOM Mechanical Configuration Each Transmitter and Receiver module occupies two slots in the EMCORE Optiva Chassis. Laser Safety This product meets the appropriate standard in Title 21 of the Code of Federal Regulations (CFR). FDA/CDRH Class 1M laser product. All versions of this laser are Class 1M laser product, tested according to IEC 60825-1:2007 / EN 60825-1:2007. An additional warning for Class 1M laser products. For diverging beams, this warning shall state that viewing the laser output with certain optical instruments (for example: eye loupes, magnifiers, and microscopes) within a distance of 100 mm may pose an eye hazard. For collimated beams, this warning shall state that viewing the laser output with certain instruments designed for use at a distance (for example: telescopes and binoculars) may pose an eye hazard. Wavelength = 1.3/1.5 μm. Maximum power = 30 mW. INVISIBLE LASER RADIATION AVOID DIRECT EXPOSURE TO BEAM Wavelength: 1.5 µm Max. Output: 50 mW Class 1M Laser Product INVISIBLE LASER RADIATION IS EMITTED FROM THE END OF FIBER OR CONNECTOR Avoid direct exposure to beam Do not view beam directly with optical instruments INVISIBLE LASER RADIATION EMITTED FROM END OF FIBER OR CONNECTOR CLASS 1M LASER PRODUCT IEC 60825-1:2007 EN 60825-1:2007 MAX OUTPUT: 50 mW WAVELENGTH: 1.5 µm (+ 1460 to 1620 nm) Complies with 21 CRF 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007 G8760-073-001 REV.3 *Caution - Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. *IEC is a registered trademark of the International Electrotechnical Commision. © 2013 EMCORE Corporation | REV 2013.10 +1 626-293-3400 [email protected] www.emcore.com Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice.