Optiva OTS-2 DBS RF Fiber Optic Links DATASHEET | APRIL 2015 SATCOM Direct Broadcast Satellite Transmitters & Receivers The Optiva OTS-2 DBS transmitter and receiver are ideal to construct 17.300 to 18.400 GHz transparent fiber optic links for antenna remoting, electronic warfare systems, broadband delay lines, signal processing systems and other high-dynamic-range applications. Optiva satellite and microwave transmitters and receivers are SNMP compliant. They can be housed in the same chassis and monitored by the same Network Management System (NMS) as Optiva HD video, audio, serial data, and USB extension / distribution cards to provide multiple format and Applications Satcom DBS Antenna Signal Distribution Ground Terminal & Intra-Facility Links Site Diversity Systems frequency transport in a single flexible platform. System Design The Optiva platform includes a wide range fiber optic transport products for satellite and microwave Electronic Warfare (EW) Systems communications from 1 MHz to 40 GHz. These units can be used to construct Broadband Delay Line and Signal Processing Systems transparent inter- and intra-facility links from 1 meter to >100 km for RF and microwave signal transport, antenna remoting, video transport, electronic warfare systems and other high-dynamic-range applications. Features / Benefits Direct Broadcast Satellite Links - Eliminates the performance and cost penalty of block conversion Low RIN Source Laser - Provides highdynamic-range of >102 dB Hz2/3 Microprocessor-Based Transmitter Control for Laser Bias, Modulator Bias & Link Gain - Provides consistent high performance operation and allows for modulator low-bias operation and SFDR >102 dB Hz2/3 SNMP V.1 and RS-232 Monitor & Control Interface - Flexible user interface options Compatible with EMCORE’s Modular Optiva Platform - Allows multiple format and frequency transport in a single chassis DWDM Operation - Increases transport capacity without increasing fiber count Optiva is a completely modular, hot-swappable platform. Both 19” rack-mount and compact tabletop, or wall-mountable enclosures are available. The 3 RU 19” rack-mount, fan-cooled enclosures (Model OT-CC-16 and OT-CC-16F) can support up to 16 insert cards and utilize two dual-redundant, hot-swappable, 100 or 200 watt power supplies. The 1 RU 19” rack-mount, fan-cooled enclosure (Model: OTCC-6-1U) can accommodate 6 insert cards and utilizes two hot-swappable 60 watt power supplies. Compact one-slot (OT-DTCR-1), or two-slot (OT-DTCR-2) enclosures are also available that use an external wall-mount power supply. Block Diagram Transmitter Receiver Externally Modulated Transmitter RF in Variable Gain RF Preamp Laser/Modulator Microprocessor Control -20 dB RF Test Point © 2015 EMCORE Corporation | REV 2015.04 PL +1 626-293-3400 Optical Output +10 dBmo min PR RFout Photodiode Optical Preamp/Rx Microprocessor Control Variable Gain RF Postamp Optical Input +11.8 dBmo max [email protected] -20 dB RF Test Point www.emcore.com Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice. Optiva OTS-2 DBS RF Fiber Optic Links DATASHEET | APRIL 2015 SATCOM Performance Highlights Parameter Frequency Range RF Input Power Min Typical Max 17.300 - 18.400 GHz - - 5* dBm Typical DBS Downlink S21 Frequency Response Units -15^ Wavelength - 1550 Optical Output Power 9 10 11 dBmo -10 - 50 °C Operating Temperature Range - nm *Tx: RF amp 15 dB gain, attenuation range 0 to 15 dB ^Tx: RF amp 35 dB gain, attenuation range 0 to 15 dB Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of the datasheet. Exposure to absolute maximum ratings for extended periods can adversely affect device reliability. Parameter Symbol Min Max Units Operating Temperature TOP -20 60 °C Storage Temperature TSTG -40 85 °C RF Input Sin NA 5* dBm Enclosure Options -15^ *Tx: RF amp 15 dB gain ^Tx: RF amp 35 dB gain Environmental Specifications Parameter Symbol Min Max Units TOP -10 50 °C Operating Humidity, Maximum Non-Condensing -- -- 95% Operating Altitude, Above Sea Level -- -- Operating Temperature 6000 ft 1828.8 m TSTG -40 70 °C Storage Humidity, Maximum Non-Condensing -- -- 95% -- Storage Altitude, Above Sea Level -- -- 50,000 ft 15,240 m Storage Temperature Network Management All modules are compliant with SNMP v.1 supported through the Optiva NMS card (OPV-CTLR-IC) © 2015 EMCORE Corporation | REV 2015.04 +1 626-293-3400 [email protected] www.emcore.com Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice. Optiva OTS-2 DBS RF Fiber Optic Links DATASHEET | APRIL 2015 SATCOM Transmitter & Receiver Optical Characteristics Symbol Condition Min Typical Max Units Wavelength Parameter l - 1530 1550 1562 nm Optical Output Power PL - 9 10 11 dBmo Connector Return Loss - - 40 - - dB Optical Connector Type - SC/APC - - - - Pin - - - +10 dBmo - - 0.7 - - A/W Receiver Optical Input Power Receiver Responsivity Note: In order to prevent reflection-induced distortion degradation, the laser should be connected to an optical cable having a return loss of at least 55 dB for discrete reflections and 30 dB for distributed reflections. DBS Transmitter & Receiver RF Characteristics Condition Min Typical Max Units Operational Bandwidth Parameter - 17.3 - 18.4 GHz RF Input Impedance - - 50 - Ω RF Return Loss - - - -15 dB - -18 -20 -22 dB RF Connectors 3.5 mm RF Test Point Reference Value, Relative to RF input or RF output* *Test point performance beyond the stated frequency range is provided; only the test point reference value tolerance may increase beyond the above stated +/- 1 dB DC Power Consumption - Max Module Type Input Voltage (VDC) Max Current (@+70°C) Transmitter +12 1A Receiver +12 750 mA Link Performance - DBS Symbol Condition Min Typical Max Units RF Bandwidth Parameter - - 17.300 - 18.400 GHz Link Gain (+0 dBmo Rx optical input)*^ G @ 17.3 GHz -10 -6 - dB G @ 18.4 GHz -10 -6 - dB G @ 17.3 GHz 10 14 - dB G @ 18.4 GHz 10 14 - dB NF @ 17.3 GHz 23 - - dB NF @ 18.4 GHz 23 - - dB NF @ 17.3 GHz 13 - - dB NF @ 18.4 GHz 13 - - dB IIP3 @ 17.3 GHz - -6 - dBm Link Gain (+10 dBmo Rx optical input)*^ Noise Figure (+0 dBmo Rx optical input)^ Noise Figure (+10 dBmo Rx optical input)^ Input IP3^ Spurious Free Dynamic Range^ Gain Variation IIP3 @ 18.4 GHz - -5 - dBm SFDR @ 0 dBmo Rx Optical Input 97 - -- dB-Hz2/3 SFDR @ +10 dBmo Rx Optical Input 101 - -- dB-Hz2/3 - Any 36 MHz - - 0.7 dB - Any 500 MHz - - 1.5 dB *Receiver RF output will change 2 dB for each 1 dB of Rx optical input power level change ^Performance based on OTS-2T/S5 with RF Amp gain of 35 dB, OTS-2R/S5 with RF Amp gain of 15 dB © 2015 EMCORE Corporation | REV 2015.04 +1 626-293-3400 [email protected] www.emcore.com Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice. Optiva OTS-2 DBS RF Fiber Optic Links DATASHEET | APRIL 2015 SATCOM Ordering Information: Transmitter Transmitter OTS-2T / 3.5-1718-WW-10-XX-12-YY-Z When ordering replace “WW” with one of the ITU Channel Options When ordering replace “XX” with one of the Optical Connector Options When ordering replace “YY” with one of the Variable Gain RF Amplifier Options When ordering replace “Z” with one of the Enclosure Options RF Connector DBS Frequency (GHz) 3.5 = 50 Ω 3.5 mm ITU Channel Options (THz / nm) “WW” 1718 = 17.300-18.400 GHz Optical Power (dBmo) Optical Connector Options “XX” 10 = +10 Optical Output Standard: SA = SC / APC Optical Output + RF Test Port (dB) 1 = Single Optical Output + 2 = -20 dB Test Port Variable Gain RF Amplifier Options (dB) “YY” Enclosure Options “Z” 15 = 15 dB 1 = Optiva Indoor Rack-Mount Installation 35 = 35 dB Optional: FA = FC / APC EA = E2000 / APC 2 = Optiva Outdoor MiniHub Installation Ordering Information: Receiver Receiver OTS-2R / 3.5-1718-10-WW-XX-2-YY-Z When ordering replace “WW” with one of the Optical Connector Options When ordering replace “XX” with one of the ITU Channel Options When ordering replace “YY” with one of the Variable Gain RF Amplifier Options When ordering replace “Z” with one of the Enclosure Options RF Connector DBS Frequency (GHz) 3.5 = 50 Ω 3.5 mm 1718 = 17.300-18.400 GHz Optical Power (dBmo) 10 = +10 Max Optical Input Optical Connector Options “WW” Standard: SA = SC / APC ITU Filter Options for Improved Optical Isolation in DWDM Systems (THz / nm) “XX” Standard: 00 = No filter 27.99 nm Test Port (dB) 2 = -20 dB Test Port Variable Gain RF Amplifier Options (dB) “Y” 15 = 15 dB 35 = 35 dB Optional: FA = FC / APC EA = E2000 / APC © 2015 EMCORE Corporation | REV 2015.04 +1 626-293-3400 Enclosure Options “Z” 1 = Optiva Indoor Rack- Mount Installation 2 = Optiva Outdoor MiniHub Installation [email protected] www.emcore.com Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice. Optiva OTS-2 DBS RF Fiber Optic Links DATASHEET | APRIL 2015 SATCOM Mechanical Configuration Each Transmitter and Receiver module occupies two slots in the EMCORE Optiva Chassis. Laser Safety This product meets the appropriate standard in Title 21 of the Code of Federal Regulations (CFR). FDA/CDRH Class 1M laser product. All versions of this laser are Class 1M laser product, tested according to IEC 60825-1:2007 / EN 60825-1:2007. An additional warning for Class 1M laser products. For diverging beams, this warning shall state that viewing the laser output with certain optical instruments (for example: eye loupes, magnifiers, and microscopes) within a distance of 100 mm may pose an eye hazard. For collimated beams, this warning shall state that viewing the laser output with certain instruments designed for use at a distance (for example: telescopes and binoculars) may pose an eye hazard. Wavelength = 1.3/1.5 μm. Maximum power = 30 mW. INVISIBLE LASER RADIATION AVOID DIRECT EXPOSURE TO BEAM Wavelength: 1.5 µm Max. Output: 50 mW Class 1M Laser Product INVISIBLE LASER RADIATION IS EMITTED FROM THE END OF FIBER OR CONNECTOR Avoid direct exposure to beam Do not view beam directly with optical instruments INVISIBLE LASER RADIATION EMITTED FROM END OF FIBER OR CONNECTOR CLASS 1M LASER PRODUCT IEC 60825-1:2007 EN 60825-1:2007 MAX OUTPUT: 50 mW WAVELENGTH: 1.5 µm (+ 1460 to 1620 nm) Complies with 21 CRF 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007 G8760-073-001 REV.3 *Caution - Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. *IEC is a registered trademark of the International Electrotechnical Commision. © 2015 EMCORE Corporation | REV 2015.04 +1 626-293-3400 [email protected] www.emcore.com Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice.