Optoway TRSL-9140FG 1 *********************************************************************************************************************************************************************** TRSL-9140FG 3.3V / 1310 nm / 2.125 Gbps SFF LC SINGLE-MODE TRANSCEIVER ********************************************************************************************************************************************************************** FEATURES DESCRIPTION l l l l l l l l l l l l l l The TRSL-9140FG series single mode transceivers is small form factor, low power, high performance module for bi-directional serial optical data communications such as Fiber Channel 2X/1X SM-LC-L FC-PI and IEEE 802.3z Gigabit Ethernet 1000BASE-LX. This module is designed for single mode fiber and operates at a nominal wavelength of 1310 nm. A guaranteed minimum optical link budget of 23 dB is offered which can correspond to a link distance of over 40 km (assuming worst case fiber loss of 0.45 dB/km). The transmitter section uses a multiple quantum well 1310 nm DFB laser and is a class 1 laser compliant according to International Safety Standard IEC-60825. The receiver section uses an integrated InGaAs detector preamplifier (IDP) mounted in an optical header and a limiting post-amplifier IC. A LVPECL logic interface simplifies interface to external circuitry. Duplex LC Single Mode Transceiver Fibre Channel 2X / 1X SM-LC-L FC-PI Compliant IEEE 802.3z Gigabit Ethernet Compliant Small Form Factor, RJ-45 size, 2X5 pin Package 1310 nm DFB LD Transmitter 23 dB Link Power Budget at Least Link Distance up to 40km AC/AC Coupled Signal Input / Output LVTTL Transmitter Disable Input LVTTL Signal Detection Output Single +3.3 V Power Supply 0 to 70oC Operation Wave Solderable and Aqueous Washable Class 1 Laser International Safety Standard IEC-60825 Compliant APPLICATIONS l l l l LASER SAFETY ATM Switches and Routers SONET / SDH Switch Infrastructure XDSL Applications Metro Edge Switching This single mode transceiver is a Class 1 laser product. It complies with IEC-60825 and FDA 21 CFR 1040.10 and 1040.11. The transceiver must be operated within the specified temperature and voltage limits. The optical ports of the module shall be terminated with an optical connector or with a dust plug. ORDER INFORMATION P/No. TRSL-9140FG Bit Rate FC-PI (Gb/s) 2.125/1.063 200/100 Distance (km) 40 Wavelengt h (nm) 1310 DFB Package 2X5 LC Temp. (oC) 0 to 70 TX Power RX Sens. RoHS (dBm) (dBm) Compliant 5 to 0 -23 Yes Absolute Maximum Ratings Parameter Storage Temperature Operating Temperature Soldering Temperature Power Supply Voltage Input Voltage Output Current Symbol Tstg Topr --Vcc --Iout Min -40 0 0 GND Max 85 70 260 4.5 Vcc Units o C o C o C V V 0 30 mA Min 3.13 0 1063 Typ 3.3 Max 3.47 70 Notes Air flow 1m/sec 10 seconds on leads only Recommended Operating Conditions Parameter Power Supply Voltage Operating Temperature Data Rate Power Supply Current Symbol Vcc Topr Icc 2125 200 300 Units / Notes V o C / air flow 1m/sec Mb/s mA *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: [email protected] http: // www.optoway.com.tw 12/1/2005 V2.0 Optoway TRSL-9140FG 2 *********************************************************************************************************************************************************************** Transmitter Specifications (0 oC < Topr < 70 oC, 3.13V < Vcc < 3. 47V) Parameter Optical Optical Transmit Power Output Center Wavelength Output Spectrum Width Side Mode Suppression Ratio Extinction Ratio Optical Modulation Amplitude (Peak-to-Peak) Optical Rise Time Optical Fall Time Relative Intensity Noise Electrical Data Input Current – Low Data Input Current – High Differential Input Voltage Data Input Voltage – Low Data Input Voltage -- High Disable Input Voltage -- Low Disable Input Voltage -- High Shut Off Time for TxDis Symbol Min Typ Max Units Notes Po λ ∆λ SMSR ER OMA 0 1280 --30 9 174 --1310 --- 5 1350 1 dBm nm nm dB dB µW 1 --- tr tf RIN IIL IIH VIH - V IL VIL - V CC VIH - V CC VTDIS,L VTDIS,H tDIS 160 160 -120 -350 350 300 -2.0 -1.1 0 Vcc – 1.3 -1.58 -0.74 0.5 Vcc 1 ps ps dB/Hz µA µA mV V V V V ms -20 dB Width FC-PI Standard 20% to 80% Values 20% to 80% Values 2 2 TX Output Enabled TX Ouput Disabled Notes: 1. Output power is power coupled into a 9/125 µm single mode fiber. 2. These inputs are compatible with 10K, 10KH and 100K ECL and PECL inputs. Receiver Specifications (0oC < Topr < 70oC, 3.13V < Vcc < 3.47V) Parameter Optical Sensitivity @ 2.125 Gbps Sensitivity @ 1.063 Gbps Maximum Input Power Signal Detect -- Asserted Signal Detect -- Deasserted Signal detect -- Hysteresis Wavelength of Operation Electrical Data Output Voltage – Low Data Output Voltage – High Signal Detect Output Voltage -- Low Signal Detect Output Voltage -- High Symbol Min Typ Max Units Notes Sen. 2X Sen. 1X Pin Pa Pd -----3 ---35 1.0 1100 ----- -23 -24 ---23 --- dBm dBm dBm dBm dBm dB nm 1 1 VOL - VCC VOH - VCC VOL VOH -2.0 -1.1 --------- 1600 -1.58 -0.74 0.5 2.0 V V V V Transition: low to high Transition: high to low 2 2 Notes: 1.Minimum sensitivity and saturation levels at BER=1E-12 for a 27-1 PRBS. 2. These outputs are compatible with 10K, 10KH and 100K ECL and PECL outputs. *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: [email protected] http: // www.optoway.com.tw 12/1/2005 V2.0 Optoway TRSL-9140FG 3 *********************************************************************************************************************************************************************** CONNECTION DIAGRAM PIN 1 2 3 4 5 6 7 8 Symbol VEEr VCC r SD RD− RD+ VCC t VEEt TDis 9 10 MS TD+ TDMS Notes Directly connect this pin to the receiver ground plane +3.3V dc power for the receiver section Active high on this indicates a received optical signal. Receiver Dataout Bar. See recommended circuit schematic Receiver Dataout. See recommended circuit schematic +3.3V dc power for the transmitter section Directly connect this plan to the transmitter ground plane Transmitter Disable. Connect this pin to +3.3V TTL logic “1” to disable module To enable module connect to TTL logic low “0” Transmitter Data In. See recommended circuit schematic Transmitter Data In Bar. See recommended circuit schematic Mounting Studs. Connect to Chassis Ground RECOMMENDED CIRCUIT SCHEMATIC Vcc3.3V TDZ=50R LVPECL TD+ TDTD+ TDis Veet Vcct TXDis(LVTTL) 10 9 8 7 6 Z=5OR Vcc3.3V 1uH 10nF 10nF 10uF 10uF PHY DEVICE 1 2 3 4 5 Veer Vccr SD RDRD+ 1uH 10nF Vcc3.3V 10uF RD+ 100R LVPECL Z=50R RDZ=5OR SD TO LVTTL STAGE Note: 1. TX input is terminated inside the module. 2. Veer and Veet are not internally connected to each other. 3. 50 Ω line pattern and component placements on TD+/TD- and RD+/RD- lines shall be symmetrical for better impedance matching. *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: [email protected] http: // www.optoway.com.tw 12/1/2005 V2.0 Optoway TRSL-9140FG 4 *********************************************************************************************************************************************************************** PACKAGE DIAGRAM Units in mm 1) Standard Case TRSL-9140FG 2) Extended Case TRSL-9140FEG Note: Specifications subject to change without notice. *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: [email protected] http: // www.optoway.com.tw 12/1/2005 V2.0