Optoway TRSL-9380 ***************************************************************************************************************************************************************************** TRSL-9380 3.3V / 1550 nm / 2.5 Gbps SFF LC SINGLE-MODE TRANSCEIVER **************************************************************************************************************************************************************************** FEATURES DESCRIPTION l Duplex LC Single Mode Transceiver l SONET OC-48 LR-2 / SDH STM-16 (L-16.2) Compliant l Fiber Channel 2X/1X SM-LC-L FC-PI Compliant l IEEE 802.3z Gigabit Ethernet Compliant l Small Form Factor, RJ-45 size, 2X5 pin Package l 1550 nm DFB LD Transmitter l APD High Sensitivity Receiver l 26 dB Link Budget at Least l Link Distance 80 km at Least l AC/AC Coupled Signal Input / Output l LVTTL Transmitter Disable Input l LVTTL Signal Detection Output l Single +3.3 V Power Supply l 0 to 70oC Operating l Wave Solderable and Aqueous Washable l Class 1 Laser International Safety Standard IEC-60825 Compliant The TRSL-9380 series single mode transceivers is small form factor, low power, high performance module for bi-directional serial optical data communications such as SONET OC-48 / SDH STM-16, gigabit Ethernet and Fiber channel. This module is designed for single mode fiber and operates at a nominal wavelength of 1550 nm. A guaranteed minimum optical link budget of 26 dB is offered which can correspond to a link distance of over 80 km (assuming worst case fiber loss of 0.25 dB/km). The transmitter section uses a multiple quantum well 1550 nm DFB laser and is a class 1 laser compliant according to International Safety Standard IEC-60825. The receiver section uses an integrated InGaAs Avalanche photodetector preamplifier mounted in an optical header and a limiting post-amplifier IC. A PECL logic interface simplifies interface to external circuitry. LASER SAFETY This single mode transceiver is a Class 1 laser product. It complies with IEC 60825 and FDA 21 CFR 1040.10 and 1040.11. The transceiver must be operated within the specified temperature and voltage limits. The optical ports of the module shall be terminated with an optical connector or with a dust plug. APPLICATIONS l Switch to Switch Interface l OC-48 ATM Links l High Speed Interface for File Servers ORDER INFORMATION P/No. TRSL-9380 Bit Rate (Mb/s) 2488 SONET /SDH LR-2 Distance (km) 80 Wavelength Package (nm) 1550 DFB 2X5 LC Temp. (oC) 0 to 70 TX Power RX Sens. (dBm) (dBm) 3 to -2 -28 Signal Detect LVTTL Absolute Maximum Ratings Parameter Storage Temperature Operating Temperature Soldering Temperature Power Supply Voltage Input Voltage Output Current Symbol Tstg Topr --Vcc --Iout Min -40 0 0 GND Max 85 70 260 4.5 Vcc Units o C o C o C V V 0 30 mA Min 3.135 0 622 Typ 3.3 Max 3.465 70 2700 Notes With air flow 1m/sec 10 seconds on leads only Recommended Operating Conditions Parameter Power Supply Voltage Operating Temperature Data Rate Symbol Vcc Topr 2488 Units V o C / air flow 1m/sec Mb/s **************************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: [email protected] http: // www.optoway.com.tw 7/1/2004 V1.0 Optoway TRSL-9380 ****************************************************************************************************************************************************************************** Transmitter Specifications (0oC < Topr < 70oC, 3.135V < Vcc < 3. 465V) Parameter Optical Optical Transmit Power Output Center Wavelength Output Spectrum Width Side Mode Suppression Ratio Extinction Ratio Output Eye Optical Rise Time Optical Fall Time Relative Intensity Noise Electrical Power Supply Current Data Input Current – Low Data Input Current – High Differential Input Voltage Data Input Voltage – Low Data Input Voltage -- High Symbol Min Typ Max Units Notes Po -2 --3 dBm 1 1500 1580 nm λ --0.2 1 nm -20 dB Width ∆λ SMSR 30 dB ER 8.2 ----dB Compliant with Bellcore TR-NWT-000253 and ITU recommendation G.957 tr 150 ps 20% to 80% Values tf 150 ps 20% to 80% Values RIN -120 dB/Hz Icc IIL IIH VIH - VIL V IL - VCC V IH - VCC 180 mA µA µA mV V V -350 350 300 -2.0 -1.1 -1.58 -0.74 2 3 3 Notes: 1. Output power is power coupled into a 9/125 µm single mode fiber. 2. Maximum current is specified at Vcc = Maximum @ maximum temperature. 3. These inputs are compatible with 10K, 10KH and 100K ECL and PECL inputs. Receiver Specifications (0oC < Topr < 70oC, 3.135V < Vcc < 3.465V) Parameter Optical Sensitivity Maximum Input Power Signal Detect -- Asserted Signal Detect -- Deasserted Signal detect -- Hysteresis Wavelength of Operation Electrical Power Supply Current Data Output Voltage – Low Data Output Voltage – High Signal Detect Output Voltage -- Low Signal Detect Output Voltage -- High Symbol Min Typ Max Units Notes --Pin Pa Pd ---8 ---40 1.0 1100 --- -28 ---28 --- dBm dBm dBm dBm dB nm 1 Icc VOL - V CC VOH - V CC VSDL VSDH --------- 1600 100 -2.0 -1.1 -1.58 -0.74 0.5 2.0 mA V V V V Transition: low to high Transition: high to low 2 3 3 Notes: 1. Minimum sensitivity and saturation levels at BER=1E-10 for a 2 23-1 PRBS. 2. The current excludes the output load current. 3. These outputs are compatible with 10K, 10KH and 100K ECL and PECL inputs. ***************************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 E-mail: [email protected] Fax: 886-3-5979737 http: // www.optoway.com.tw 7/1/2004 V1.0 Optoway TRSL-9380 ****************************************************************************************************************************************************************************** CONNECTION DIAGRAM PIN 1 2 3 4 5 6 7 8 Symbol V EEr V CC r SD RD− RD+ V CC t V EEt TxDis 9 10 MS TD+ TDMS Notes Directly connect this pin to the receiver ground plane +3.3V dc power for the receiver section Active high on this indicates a received optical signal. Receiver Dataout Bar. See recommended circuit schematic Receiver Dataout. See recommended circuit schematic +3.3V dc power for the transmitter section Directly connect this plan to the transmitter ground plane Transmitter Disable. Connect this pin to +3.3V TTL logic “1” to disable module To enable module connect to TTL logic low “0” Transmitter Data In. See recommended circuit schematic Transmitter Data In Bar. See recommended circuit schematic Mounting Studs. Connect to Chassis Ground RECOMMENDED CIRCUIT SCHEMATIC Vcc3.3V TDZ=50R LVPECL TD+ TDTD+ TDis Veet Vcct TXDis(LVTTL) 10 9 8 7 6 Z=5OR Vcc3.3V 1uH 10nF 10nF 10uF 10uF PHY DEVICE 1 2 3 4 5 Veer Vccr SD RDRD+ 1uH 10nF Vcc3.3V 10uF RD+ 100R LVPECL Z=50R RDZ=5OR SD TO LVTTL STAGE ***************************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 E-mail: [email protected] Fax: 886-3-5979737 http: // www.optoway.com.tw 7/1/2004 V1.0 Optoway TRSL-9380 ****************************************************************************************************************************************************************************** PACKAGE DIAGRAM Units in mm 1) Standard Case TRSL-9380 2) Extended Case TRSL-9380E Note: Specifications subject to change without notice. ***************************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 E-mail: [email protected] Fax: 886-3-5979737 http: // www.optoway.com.tw 7/1/2004 V1.0