M29F040B 4 Mbit (512Kb x8, Uniform Block) Single Supply Flash Memory PRELIMINARY DATA ■ SINGLE 5V ± 10% SUPPLY VOLTAGE for PROGRAM, ERASE and READ OPERATIONS ■ ACCESS TIME: 45ns ■ PROGRAMMING TIME – 8µs per Byte typical ■ 8 UNIFORM 64 Kbytes MEMORY BLOCKS ■ PROGRAM/ERASE CONTROLLER PLCC32 (K) TSOP32 (N) 8 x 20mm – Embedded Byte Program algorithm – Embedded Multi-Block/Chip Erase algorithm – Status Register Polling and Toggle Bits ■ ERASE SUSPEND and RESUME MODES – Read and Program another Block during Erase Suspend ■ 32 UNLOCK BYPASS PROGRAM COMMAND 1 PDIP32 (P) – Faster Production/Batch Programming ■ LOW POWER CONSUMPTION – Standby and Automatic Standby ■ ■ 100,000 PROGRAM/ERASE CYCLES per BLOCK Figure 1. Logic Diagram 20 YEARS DATA RETENTION – Defectivity below 1 ppm/year ■ VCC ELECTRONIC SIGNATURE – Manufacturer Code: 20h – Device Code: E2h 19 8 A0-A18 W DQ0-DQ7 M29F040B E G VSS AI02900 September 1999 This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. 1/21 M29F040B Figure 2B. TSOP Connections A11 A9 A8 A13 A14 A17 W VCC A18 A16 A15 A12 A7 A6 A5 A4 A12 A15 A16 A18 VCC W A17 Figure 2A. PLCC Connections 1 32 A7 A6 A5 A4 A3 A2 A1 A0 DQ0 9 M29F040B 25 A14 A13 A8 A9 A11 G A10 E DQ7 DQ1 DQ2 VSS DQ3 DQ4 DQ5 DQ6 17 AI02901 1 8 9 32 M29F040B 16 25 24 17 G A10 E DQ7 DQ6 DQ5 DQ4 DQ3 VSS DQ2 DQ1 DQ0 A0 A1 A2 A3 AI02902 Figure 2C. PDIP Connections A18 A16 A15 A12 A7 A6 A5 A4 A3 A2 A1 A0 DQ0 DQ1 DQ2 VSS 1 32 2 31 3 30 4 29 5 28 6 27 7 26 8 25 M29F040B 9 24 10 23 11 22 12 21 13 20 14 19 15 18 16 17 AI02910 2/21 Table 1. Signal Names VCC W A17 A14 A13 A8 A9 A11 G A10 E DQ7 DQ6 DQ5 DQ4 DQ3 A0-A18 Address Inputs DQ0-DQ7 Data Inputs/Outputs E Chip Enable G Output Enable W Write Enable VCC Supply Voltage VSS Ground SUMMARY DESCRIPTION The M29F040B is a 4 Mbit (512Kb x8) non-volatile memory that can be read, erased and reprogrammed. These operations can be performed using a single 5V supply. On power-up the memory defaults to its Read mode where it can be read in the same way as a ROM or EPROM. The M29F040B is fully backward compatible with the M29F040. The memory is divided into blocks that can be erased independently so it is possible to preserve M29F040B Table 2. Absolute Maximum Ratings (1) Symbol Parameter Value Unit Ambient Operating Temperature (Temperature Range Option 1) 0 to 70 °C Ambient Operating Temperature (Temperature Range Option 6) –40 to 85 °C Ambient Operating Temperature (Temperature Range Option 3) –40 to 125 °C TBIAS Temperature Under Bias –50 to 125 °C TSTG Storage Temperature –65 to 150 °C VIO (2) Input or Output Voltage –0.6 to 6 V VCC Supply Voltage –0.6 to 6 V VID Identification Voltage –0.6 to 13.5 V TA Note: 1. Except for the rating ”Operating Temperature Range”, stresses above those listed in the Table ”Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant quality documents. 2. Minimum Voltage may undershoot to –2V during transition and for less than 20ns during transitions. valid data while old data is erased. Each block can be protected independently to prevent accidental Program or Erase commands from modifying the memory. Program and Erase commands are written to the Command Interface of the memory. An on-chip Program/Erase Controller simplifies the process of programming or erasing the memory by taking care of all of the special operations that are required to update the memory contents. The end of a program or erase operation can be detected and any error conditions identified. The command set required to control the memory is consistent with JEDEC standards. Chip Enable, Output Enable and Write Enable signals control the bus operation of the memory. They allow simple connection to most microprocessors, often without additional logic. The memory is offered in TSOP32 (8 x 20mm), PLCC32 and PDIP32 packages. Access times of 45ns, 55ns, 70ns and 90ns are available. The memory is supplied with all the bits erased (set to ‘1’). SIGNAL DESCRIPTIONS See Figure 1, Logic Diagram, and Table 1, Signal Names, for a brief overview of the signals connected to this device. Address Inputs (A0-A18). The Address Inputs select the cells in the memory array to access during Bus Read operations. During Bus Write operations they control the commands sent to the Command Interface of the internal state machine. Data Inputs/Outputs (DQ0-DQ7). The Data Inputs/Outputs output the data stored at the selected address during a Bus Read operation. During Bus Write operations they represent the commands sent to the Command Interface of the internal state machine. Chip Enable (E). The Chip Enable, E, activates the memory, allowing Bus Read and Bus Write operations to be performed. When Chip Enable is High, VIH, all other pins are ignored. Output Enable (G). The Output Enable, G, controls the Bus Read operation of the memory. Write Enable (W). The Write Enable, W, controls the Bus Write operation of the memory’s Command Interface. VCC Supply Voltage. The VCC Supply Voltage supplies the power for all operations (Read, Program, Erase etc.). The Command Interface is disabled when the VCC Supply Voltage is less than the Lockout Voltage, VLKO. This prevents Bus Write operations from accidentally damaging the data during power up, power down and power surges. If the Program/ Erase Controller is programming or erasing during this time then the operation aborts and the memory contents being altered will be invalid. A 0.1µF capacitor should be connected between the VCC Supply Voltage pin and the VSS Ground pin to decouple the current surges from the power supply. The PCB track widths must be sufficient to carry the currents required during program and erase operations, I CC4. VSS Ground. The VSS Ground is the reference for all voltage measurements. 3/21 M29F040B Table 3. Block Addresses Size (Kbytes) Address Range 64 70000h-7FFFFh 64 60000h-6FFFFh 64 50000h-5FFFFh 64 40000h-4FFFFh 64 30000h-3FFFFh 64 20000h-2FFFFh 64 10000h-1FFFFh 64 00000h-0FFFFh BUS OPERATIONS There are five standard bus operations that control the device. These are Bus Read, Bus Write, Output Disable, Standby and Automatic Standby. See Table 4, Bus Operations, for a summary. Typically glitches of less than 5ns on Chip Enable or Write Enable are ignored by the memory and do not affect bus operations. Bus Read. Bus Read operations read from the memory cells, or specific registers in the Command Interface. A valid Bus Read operation involves setting the desired address on the Address Inputs, applying a Low signal, V IL, to Chip Enable and Output Enable and keeping Write Enable High, VIH. The Data Inputs/Outputs will output the value, see Figure 7, Read Mode AC Waveforms, and Table 11, Read AC Characteristics, for details of when the output becomes valid. 4/21 Bus Write. Bus Write operations write to the Command Interface. A valid Bus Write operation begins by setting the desired address on the Address Inputs. The Address Inputs are latched by the Command Interface on the falling edge of Chip Enable or Write Enable, whichever occurs last. The Data Inputs/Outputs are latched by the Command Interface on the rising edge of Chip Enable or Write Enable, whichever occurs first. Output Enable must remain High, VIH, during the whole Bus Write operation. See Figures 8 and 9, Write AC Waveforms, and Tables 12 and 13, Write AC Characteristics, for details of the timing requirements. Output Disable. The Data Inputs/Outputs are in the high impedance state when Output Enable is High, VIH. Standby. When Chip Enable is High, VIH, the Data Inputs/Outputs pins are placed in the highimpedance state and the Supply Current is reduced to the Standby level. When Chip Enable is at VIH the Supply Current is reduced to the TTL Standby Supply Current, ICC2. To further reduce the Supply Current to the CMOS Standby Supply Current, ICC3, Chip Enable should be held within VCC ± 0.2V. For Standby current levels see Table 10, DC Characteristics. During program or erase operations the memory will continue to use the Program/Erase Supply Current, ICC4, for Program or Erase operations until the operation completes. M29F040B Table 4. Bus Operations Operation G W Bus Read VIL V IL VIH Cell Address Bus Write VIL VIH VIL Command Address X VIH VIH X Hi-Z Standby VIH X X X Hi-Z Read Manufacturer Code VIL V IL VIH A0 = VIL, A1 = VIL, A9 = VID, Others VIL or VIH 20h Read Device Code VIL V IL VIH A0 = VIH, A1 = VIL, A9 = VID, Others VIL or VIH E2h Output Disable Address Inpu ts Data Inputs/Outpu ts E Data Output Data Input Note: X = VIL or VIH. Automatic Standby. If CMOS levels (VCC ± 0.2V) are used to drive the bus and the bus is inactive for 150ns or more the memory enters Automatic Standby where the internal Supply Current is reduced to the CMOS Standby Supply Current, ICC3. The Data Inputs/Outputs will still output data if a Bus Read operation is in progress. Special Bus Operations Additional bus operations can be performed to read the Electronic Signature and also to apply and remove Block Protection. These bus operations are intended for use by programming equipment and are not usually used in applications. They require VID to be applied to some pins. Electronic Signature. The memory has two codes, the manufacturer code and the device code, that can be read to identify the memory. These codes can be read by applying the signals listed in Table 4, Bus Operations. Block Protection and Blocks Unprotection. Each block can be separately protected against accidental Program or Erase. Protected blocks can be unprotected to allow data to be changed. Block Protection and Blocks Unprotection operations must only be performed on programming equipment. For further information refer to Application Note AN1122, Applying Protection and Unprotection to M29 Series Flash. 5/21 M29F040B COMMAND INTERFACE All Bus Write operations to the memory are interpreted by the Command Interface. Commands consist of one or more sequential Bus Write operations. Failure to observe a valid sequence of Bus Write operations will result in the memory returning to Read mode. The long command sequences are imposed to maximize data security. The commands are summarized in Table 5, Commands. Refer to Table 5 in conjunction with the text descriptions below. Read/Reset Command. The Read/Reset command returns the memory to its Read mode where it behaves like a ROM or EPROM. It also resets the errors in the Status Register. Either one or three Bus Write operations can be used to issue the Read/Reset command. If the Read/Reset command is issued during a Block Erase operation or following a Programming or Erase error then the memory will take up to 10µs to abort. During the abort period no valid data can be read from the memory. Issuing a Read/Reset command during a Block Erase operation will leave invalid data in the memory. Auto Select Command. The Auto Select command is used to read the Manufacturer Code, the Device Code and the Block Protection Status. Three consecutive Bus Write operations are required to issue the Auto Select command. Once the Auto Select command is issued the memory remains in Auto Select mode until another command is issued. From the Auto Select mode the Manufacturer Code can be read using a Bus Read operation with A0 = VIL and A1 = VIL. The other address bits may be set to either VIL or VIH. The Manufacturer Code for STMicroelectronics is 20h. The Device Code can be read using a Bus Read operation with A0 = VIH and A1 = VIL. The other address bits may be set to either VIL or VIH. The Device Code for the M29F040B is E2h. The Block Protection Status of each block can be read using a Bus Read operation with A0 = VIL, A1 = VIH, and A16, A17 and A18 specifying the address of the block. The other address bits may be set to either VIL or V IH. If the addressed block is protected then 01h is output on the Data Inputs/ Outputs, otherwise 00h is output. Program Command. The Program command can be used to program a value to one address in the memory array at a time. The command requires four Bus Write operations, the final write operation latches the address and data in the internal 6/21 state machine and starts the Program/Erase Controller. If the address falls in a protected block then the Program command is ignored, the data remains unchanged. The Status Register is never read and no error condition is given. During the program operation the memory will ignore all commands. It is not possible to issue any command to abort or pause the operation. Typical program times are given in Table 6. Bus Read operations during the program operation will output the Status Register on the Data Inputs/Outputs. See the section on the Status Register for more details. After the program operation has completed the memory will return to the Read mode, unless an error has occurred. When an error occurs the memory will continue to output the Status Register. A Read/Reset command must be issued to reset the error condition and return to Read mode. Note that the Program command cannot change a bit set at ’0’ back to ’1’ and attempting to do so will cause an error. One of the Erase Commands must be used to set all the bits in a block or in the whole memory from ’0’ to ’1’. Unlock Bypass Command. The Unlock Bypass command is used in conjunction with the Unlock Bypass Program command to program the memory. When the access time to the device is long (as with some EPROM programmers) considerable time saving can be made by using these commands. Three Bus Write operations are required to issue the Unlock Bypass command. Once the Unlock Bypass command has been issued the memory will only accept the Unlock Bypass Program command and the Unlock Bypass Reset command. The memory can be read as if in Read mode. Unlock Bypass Program Command. The Unlock Bypass Program command can be used to program one address in memory at a time. The command requires two Bus Write operations, the final write operation latches the address and data in the internal state machine and starts the Program/Erase Controller. The Program operation using the Unlock Bypass Program command behaves identically to the Program operation using the Program command. A protected block cannot be programmed; the operation cannot be aborted and the Status Register is read. Errors must be reset using the Read/Reset command, which leaves the device in Unlock Bypass Mode. See the Program command for details on the behavior. M29F040B Command Length Table 5. Commands Bus Write Operations 1st 2nd Addr Data 1 X F0 3 555 Auto Select 3 Program 3rd 4th Addr Data Addr Data AA 2AA 55 X F0 555 AA 2AA 55 555 90 4 555 AA 2AA 55 555 A0 Unlock Bypass 3 555 AA 2AA 55 555 20 Unlock Bypass Program 2 X A0 PA PD Unlock Bypass Reset 2 X 90 X 00 Chip Erase 6 555 AA 2AA 55 555 Block Erase 6+ 555 AA 2AA 55 555 Erase Suspend 1 X B0 Erase Resume 1 X 30 5th Addr Data PA PD 80 555 80 555 6th Addr Data Addr Data AA 2AA 55 555 10 AA 2AA 55 BA 30 Read/Reset Note: X Don’t Care, PA Program Address, PD Program Data, BA Any address in the Block. All values in the table are in hexadecimal. The Command Interface only uses address bits A0-A10 to verify the commands, the upper address bits are Don’t Care. Read/Reset. After a Read/Reset command, read the memory as normal until another command is issued. Auto Select. After an Auto Select command, read Manufacturer ID, Device ID or Block Protection Status. Program, Unlock Bypass Program, Chip Erase, Block Erase. After these commands read the Status Register until the Program/Erase Controller completes and the memory returns to Read Mode. Add additional Blocks during Block Erase Command with additional Bus Writ e Operations until the Timeout Bit is set. Unlock Bypass. After the Unlock Bypass command issue Unlock Bypass Program or Unlock Bypass Reset commands. Unlock Bypass Reset. After the Unlock Bypass Reset command read the memory as normal until another command is issued. Erase Suspend. After the Erase Suspend command read non-erasing memory blocks as normal, issue Auto Select and Program commands on non-erasing blocks as normal. Erase Resume. After the Erase Resume command the suspended Erase operation resumes, read the Status Register until the Program/ Erase Controller completes and the memory returns to Read Mode. Unlock Bypass Reset Command. The Unlock Bypass Reset command can be used to return to Read/Reset mode from Unlock Bypass Mode. Two Bus Write operations are required to issue the Unlock Bypass Reset command. Chip Erase Command. The Chip Erase command can be used to erase the entire chip. Six Bus Write operations are required to issue the Chip Erase Command and start the Program/Erase Controller. If any blocks are protected then these are ignored and all the other blocks are erased. If all of the blocks are protected the Chip Erase operation appears to start but will terminate within about 100µs, leaving the data unchanged. No error condition is given when protected blocks are ignored. During the erase operation the memory will ignore all commands. It is not possible to issue any command to abort the operation. Typical chip erase times are given in Table 6. All Bus Read operations during the Chip Erase operation will output the Status Register on the Data Inputs/Outputs. See the section on the Status Register for more details. After the Chip Erase operation has completed the memory will return to the Read Mode, unless an error has occurred. When an error occurs the memory will continue to output the Status Register. A Read/Reset command must be issued to reset the error condition and return to Read Mode. The Chip Erase Command sets all of the bits in unprotected blocks of the memory to ’1’. All previous data is lost. 7/21 M29F040B Table 6. Program, Erase Times and Program, Erase Endurance Cycles (TA = 0 to 70°C, –40 to 85°C or –40 to 125°C) Parameter Min Chip Erase (All bits in the memory set to ‘0’) Chip Erase Block Erase (64 Kbytes) Program Chip Program Program/Erase Cycles (per Block) 100,000 Typ (1) Typical after 100k W/E Cycles (1) 1.5 1.5 5 5 20 sec 0.6 0.6 4 sec 8 8 150 µs 4.5 4.5 18 sec Max Unit sec cycles Note: 1. TA = 25°C, VCC = 5V. Block Erase Command. The Block Erase command can be used to erase a list of one or more blocks. Six Bus Write operations are required to select the first block in the list. Each additional block in the list can be selected by repeating the sixth Bus Write operation using the address of the additional block. The Block Erase operation starts the Program/Erase Controller about 50µs after the last Bus Write operation. Once the Program/Erase Controller starts it is not possible to select any more blocks. Each additional block must therefore be selected within 50µs of the last block. The 50µs timer restarts when an additional block is selected. The Status Register can be read after the sixth Bus Write operation. See the Status Register for details on how to identify if the Program/Erase Controller has started the Block Erase operation. If any selected blocks are protected then these are ignored and all the other selected blocks are erased. If all of the selected blocks are protected the Block Erase operation appears to start but will terminate within about 100µs, leaving the data unchanged. No error condition is given when protected blocks are ignored. During the Block Erase operation the memory will ignore all commands except the Erase Suspend and Read/Reset commands. Typical block erase times are given in Table 6. All Bus Read operations during the Block Erase operation will output the Status Register on the Data Inputs/Outputs. See the section on the Status Register for more details. After the Block Erase operation has completed the memory will return to the Read Mode, unless an error has occurred. When an error occurs the memory will continue to output the Status Regis- 8/21 ter. A Read/Reset command must be issued to reset the error condition and return to Read mode. The Block Erase Command sets all of the bits in the unprotected selected blocks to ’1’. All previous data in the selected blocks is lost. Erase Suspend Command. The Erase Suspend Command may be used to temporarily suspend a Block Erase operation and return the memory to Read mode. The command requires one Bus Write operation. The Program/Erase Controller will suspend within 15µs of the Erase Suspend Command being issued. Once the Program/Erase Controller has stopped the memory will be set to Read mode and the Erase will be suspended. If the Erase Suspend command is issued during the period when the memory is waiting for an additional block (before the Program/Erase Controller starts) then the Erase is suspended immediately and will start immediately when the Erase Resume Command is issued. It will not be possible to select any further blocks for erasure after the Erase Resume. During Erase Suspend it is possible to Read and Program cells in blocks that are not being erased; both Read and Program operations behave as normal on these blocks. Reading from blocks that are being erased will output the Status Register. It is also possible to enter the Auto Select mode: the memory will behave as in the Auto Select mode on all blocks until a Read/Reset command returns the memory to Erase Suspend mode. Erase Resume Command. The Erase Resume command must be used to restart the Program/ Erase Controller from Erase Suspend. An erase can be suspended and resumed more than once. M29F040B Table 7. Status Register Bits Operation Address DQ7 DQ6 DQ5 DQ3 DQ2 Program Any Address DQ7 Toggle 0 – – Program During Erase Suspend Any Address DQ7 Toggle 0 – – Program Error Any Address DQ7 Toggle 1 – – Chip Erase Any Address 0 Toggle 0 1 Toggle Block Erase before timeout Erasing Block 0 Toggle 0 0 Toggle Non-Erasing Block 0 Toggle 0 0 No Toggle Erasing Block 0 Toggle 0 1 Toggle Non-Erasing Block 0 Toggle 0 1 No Toggle Erasing Block 1 No Toggle 0 1 Toggle Block Erase Erase Suspend Non-Erasing Block Data read as normal Good Block Address 0 Toggle 1 1 No Toggle Faulty Block Address 0 Toggle 1 1 Toggle Erase Error Note: Unspecified data bits should be ignored. STATUS REGISTER Bus Read operations from any address always read the Status Register during Program and Erase operations. It is also read during Erase Suspend when an address within a block being erased is accessed. The bits in the Status Register are summarized in Table 7, Status Register Bits. Data Polling Bit (DQ7). The Data Polling Bit can be used to identify whether the Program/Erase Controller has successfully completed its operation or if it has responded to an Erase Suspend. The Data Polling Bit is output on DQ7 when the Status Register is read. During Program operations the Data Polling Bit outputs the complement of the bit being programmed to DQ7. After successful completion of the Program operation the memory returns to Read mode and Bus Read operations from the address just programmed output DQ7, not its complement. During Erase operations the Data Polling Bit outputs ’0’, the complement of the erased state of DQ7. After successful completion of the Erase operation the memory returns to Read Mode. In Erase Suspend mode the Data Polling Bit will output a ’1’ during a Bus Read operation within a block being erased. The Data Polling Bit will change from a ’0’ to a ’1’ when the Program/Erase Controller has suspended the Erase operation. Figure 3, Data Polling Flowchart, gives an example of how to use the Data Polling Bit. A Valid Ad- dress is the address being programmed or an address within the block being erased. Toggle Bit (DQ6). The Toggle Bit can be used to identify whether the Program/Erase Controller has successfully completed its operation or if it has responded to an Erase Suspend. The Toggle Bit is output on DQ6 when the Status Register is read. During Program and Erase operations the Toggle Bit changes from ’0’ to ’1’ to ’0’, etc., with successive Bus Read operations at any address. After successful completion of the operation the memory returns to Read mode. During Erase Suspend mode the Toggle Bit will output when addressing a cell within a block being erased. The Toggle Bit will stop toggling when the Program/Erase Controller has suspended the Erase operation. Figure 4, Data Toggle Flowchart, gives an example of how to use the Data Toggle Bit. Error Bit (DQ5). The Error Bit can be used to identify errors detected by the Program/Erase Controller. The Error Bit is set to ’1’ when a Program, Block Erase or Chip Erase operation fails to write the correct data to the memory. If the Error Bit is set a Read/Reset command must be issued before other commands are issued. The Error bit is output on DQ5 when the Status Register is read. Note that the Program command cannot change a bit set at ’0’ back to ’1’ and attempting to do so will cause an error. One of the Erase commands must be used to set all the bits in a block or in the whole memory from ’0’ to ’1’. 9/21 M29F040B Figure 3. Data Polling Flowchart Figure 4. Data Toggle Flowchart START START READ DQ5 & DQ7 at VALID ADDRESS READ DQ5 & DQ6 DQ7 = DATA DQ6 = TOGGLE YES YES NO NO NO DQ5 =1 YES READ DQ7 READ DQ6 DQ6 = TOGGLE YES FAIL NO YES NO PASS AI01369 Erase Timer Bit (DQ3). The Erase Timer Bit can be used to identify the start of Program/Erase Controller operation during a Block Erase command. Once the Program/Erase Controller starts erasing the Erase Timer Bit is set to ’1’. Before the Program/Erase Controller starts the Erase Timer Bit is set to ’0’ and additional blocks to be erased may be written to the Command Interface. The Erase Timer Bit is output on DQ3 when the Status Register is read. Alternative Toggle Bit (DQ2). The Alternative Toggle Bit can be used to monitor the Program/ Erase controller during Erase operations. The Alternative Toggle Bit is output on DQ2 when the Status Register is read. During Chip Erase and Block Erase operations the Toggle Bit changes from ’0’ to ’1’ to ’0’, etc., with successive Bus Read operations from addresses 10/21 DQ5 =1 YES DQ7 = DATA NO FAIL PASS AI01370 within the blocks being erased. Once the operation completes the memory returns to Read mode. During Erase Suspend the Alternative Toggle Bit changes from ’0’ to ’1’ to ’0’, etc. with successive Bus Read operations from addresses within the blocks being erased. Bus Read operations to addresses within blocks not being erased will output the memory cell data as if in Read mode. After an Erase operation that causes the Error Bit to be set the Alternative Toggle Bit can be used to identify which block or blocks have caused the error. The Alternative Toggle Bit changes from ’0’ to ’1’ to ’0’, etc. with successive Bus Read Operations from addresses within blocks that have not erased correctly. The Alternative Toggle Bit does not change if the addressed block has erased correctly. M29F040B Table 8. AC Measurement Conditions M29F040B Parameter 45 / 55 70 / 90 High Speed Standard 30pF 100pF Input Rise and Fall Times ≤ 10ns ≤ 10ns Input Pulse Voltages 0 to 3V 0.45 to 2.4V 1.5V 0.8V and 2V AC Test Conditions Load Capacitance (CL) Input and Output Timing Ref. Voltages Figure 5. AC Testing Input Output Waveform Figure 6. AC Testing Load Circuit 1.3V High Speed 1N914 3V 1.5V 3.3kΩ 0V DEVICE UNDER TEST Standard OUT CL = 30pF or 100pF 2.4V 2.0V 0.8V 0.45V AI01275B CL includes JIG capacitance AI03027 Table 9. Capacitance (TA = 25 °C, f = 1 MHz) Symbol C IN COUT Parameter Input Capacitance Output Capacitance Test Condition Min Max Unit V IN = 0V 6 pF VOUT = 0V 12 pF Note: Sampled only, not 100% tested. 11/21 M29F040B Table 10. DC Characteristics (TA = 0 to 70°C, –40 to 85°C or –40 to 125°C) Symbol Parameter Test Condition ILI Input Leakage Current ILO Output Leakage Current ICC1 Supply Current (Read) ICC2 Supply Current (Standby) TTL ICC3 Supply Current (Standby) CMOS E = VCC ± 0.2V ICC4 (1) Supply Current (Program/Erase) Program/Erase Controller active Min Typ. (2) Max Unit 0V ≤ V IN ≤ VCC ±1 µA 0V ≤ VOUT ≤ V CC ±1 µA 15 mA 1 mA 100 µA 20 mA E = VIL, G = VIH, f = 6MHz 7 E = VIH 30 VIL Input Low Voltage –0.5 0.8 V VIH Input High Voltage 2 VCC + 0.5 V VOL Output Low Voltage 0.45 V Output High Voltage TTL IOH = –2.5mA 2.4 V Output High Voltage CMOS IOH = –100µA VCC – 0.4 V VOH VID Identification Voltage IID Identification Current VLKO (1) Program/Erase Lockout Supply Voltage Note: 1. Sampled only, not 100% tested. 2. TA = 25 °C, VCC = 5V. 12/21 IOL = 5.8mA 11.5 A9 = VID 3.2 12.5 V 100 µA 4.2 V M29F040B Table 11. Read AC Characteristics (TA = 0 to 70°C, –40 to 85°C or –40 to 125°C) M29F040B Symbol Alt Parameter Test Condition Unit 45 55 70 / 90 tAVAV tRC Address Valid to Next Address Valid E = VIL, G = VIL Min 45 55 70 ns tAVQV tACC Address Valid to Output Valid E = VIL, G = VIL Max 45 55 70 ns tELQX (1) tLZ Chip Enable Low to Output Transition G = VIL Min 0 0 0 ns tELQV tCE Chip Enable Low to Output Valid G = VIL Max 45 55 70 ns tGLQX (1) tOLZ Output Enable Low to Output Transition E = VIL Min 0 0 0 ns tGLQV tOE Output Enable Low to Output Valid E = VIL Max 25 30 30 ns tEHQZ (1) tHZ Chip Enable High to Output Hi-Z G = VIL Max 15 18 20 ns tGHQZ (1) tDF Output Enable High to Output Hi-Z E = VIL Max 15 18 20 ns tEHQX tGHQX tAXQX tOH Chip Enable, Output Enable or Address Transition to Output Transition Min 0 0 0 ns Note: 1. Sampled only, not 100% tested. Figure 7. Read Mode AC Waveforms tAVAV A0-A18 VALID tAVQV tAXQX E tELQV tEHQX tELQX tEHQZ G tGLQX tGLQV DQ0-DQ7 tGHQX tGHQZ VALID AI02903 13/21 M29F040B Table 12. Write AC Characteristics, Write Enable Controlled (TA = 0 to 70 °C, –40 to 85 °C or –40 to 125 °C) M29F040B Symbol Alt Unit Parameter 45 55 70 / 90 tAVAV tWC Address Valid to Next Address Valid Min 45 55 70 ns tELWL tCS Chip Enable Low to Write Enable Low Min 0 0 0 ns tWLWH tWP Write Enable Low to Write Enable High Min 40 40 45 ns tDVWH tDS Input Valid to Write Enable High Min 25 25 30 ns tWHDX tDH Write Enable High to Input Transition Min 0 0 0 ns tWHEH tCH Write Enable High to Chip Enable High Min 0 0 0 ns tWHWL tWPH Write Enable High to Write Enable Low Min 20 20 20 ns tAVWL tAS Address Valid to Write Enable Low Min 0 0 0 ns tWLAX tAH Write Enable Low to Address Transition Min 40 40 45 ns Output Enable High to Write Enable Low Min 0 0 0 ns tGHWL tWHGL tOEH Write Enable High to Output Enable Low Min 0 0 0 ns t VCHEL tVCS V CC High to Chip Enable Low Min 50 50 50 µs Figure 8. Write AC Waveforms, Write Enable Controlled tAVAV A0-A18 VALID tWLAX tAVWL tWHEH E tELWL tWHGL G tGHWL tWLWH W tWHWL tDVWH DQ0-DQ7 tWHDX VALID VCC tVCHEL 14/21 AI02908 M29F040B Table 13. Write AC Characteristics, Chip Enable Controlled (TA = 0 to 70 °C, –40 to 85 °C or –40 to 125 °C) M29F040B Symbol Alt Unit Parameter 45 55 70 / 90 tAVAV tWC Address Valid to Next Address Valid Min 45 55 70 ns t WLEL tWS Write Enable Low to Chip Enable Low Min 0 0 0 ns tELEH tCP Chip Enable Low to Chip Enable High Min 40 40 45 ns tDVEH tDS Input Valid to Chip Enable High Min 25 25 30 ns tEHDX tDH Chip Enable High to Input Transition Min 0 0 0 ns tEHWH tWH Chip Enable High to Write Enable High Min 0 0 0 ns tEHEL tCPH Chip Enable High to Chip Enable Low Min 20 20 20 ns tAVEL tAS Address Valid to Chip Enable Low Min 0 0 0 ns tELAX tAH Chip Enable Low to Address Transition Min 40 40 45 ns Output Enable High Chip Enable Low Min 0 0 0 ns t GHEL t EHGL tOEH Chip Enable High to Output Enable Low Min 0 0 0 ns tVCHWL tVCS V CC High to Write Enable Low Min 50 50 50 µs Figure 9. Write AC Waveforms, Chip Enable Controlled tAVAV A0-A18 VALID tELAX tAVEL tEHWH W tWLEL tEHGL G tGHEL tELEH E tEHEL tDVEH DQ0-DQ7 tEHDX VALID VCC tVCHWL AI02909 15/21 M29F040B Table 14. Ordering Information Scheme Example: M29F040B 55 N 1 T Device Type M29 Operating Voltage F = VCC = 5V ± 10% Device Function 040B = 4 Mbit (512Kb x8), Uniform Block Speed 45 = 45 ns 55 = 55 ns 70 = 70 ns 90 = 90 ns Package K = PLCC32 N = TSOP32: 8 x 20 mm P = PDIP32 Temperature Range 1 = 0 to 70 °C 3 = –40 to 125 °C 6 = –40 to 85 °C Optio n T = Tape & Reel Packing Note: The last two characters of the ordering code may be replaced by a letter code for preprogrammed parts, otherwise devices are shipped from the factory with the memory content erased (to FFh). For a list of available options (Speed, Package, etc...) or for further information on any aspect of this device, please contact the ST Sales Office nearest to you. 16/21 M29F040B Table 15. Revision History Date Revision Details July 1999 First Issue 09/21/99 ICC1 Typ. specification added (Table 10) ICC3 Typ. specification added (Table 10) 17/21 M29F040B Table 16. PLCC32 - 32 lead Plastic Leaded Chip Carrier, rectangular, Package Mechanical Data mm Symbol Typ inches Min Max A 2.54 A1 1.52 A2 Typ Min Max 3.56 0.100 0.140 2.41 0.060 0.095 0.38 0.015 B 0.33 0.53 0.013 0.021 B1 0.66 0.81 0.026 0.032 D 12.32 12.57 0.485 0.495 D1 11.35 11.56 0.447 0.455 D2 9.91 10.92 0.390 0.430 E 14.86 15.11 0.585 0.595 E1 13.89 14.10 0.547 0.555 E2 12.45 13.46 0.490 0.530 – – – – 0.00 0.25 0.000 0.010 – – – – e 1.27 F R 0.89 0.050 0.035 N 32 32 Nd 7 7 Ne 9 9 CP 0.10 0.004 Figure 10. PLCC32 - 32 lead Plastic Leaded Chip Carrier, rectangular, Package Outline D D1 A1 A2 1 N B1 E1 E Ne e D2/E2 F B 0.51 (.020) 1.14 (.045) A Nd R PLCC Drawing is not to scale. 18/21 CP M29F040B Table 17. TSOP32 - 32 lead Plastic Thin Small Outline, 8 x 20mm, Package Mechanical Data mm inches Symbol Typ Min Max A Typ Min 1.20 Max 0.047 A1 0.05 0.15 0.002 0.006 A2 0.95 1.05 0.037 0.041 B 0.15 0.27 0.006 0.011 C 0.10 0.21 0.004 0.008 D 19.80 20.20 0.780 0.795 D1 18.30 18.50 0.720 0.728 E 7.90 8.10 0.311 0.319 – – – – L 0.50 0.70 0.020 0.028 α 0° 5° 0° 5° N 32 e 0.50 0.020 32 CP 0.10 0.004 Figure 11. TSOP32 - 32 lead Plastic Thin Small Outline, 8 x 20mm, Package Outline A2 1 N e E B N/2 D1 A CP D DIE C TSOP-a A1 α L Drawing is not to scale. 19/21 M29F040B Table 18. PDIP32 - 32 lead Plastic DIP, 600 mils width, Package Mechanical Data mm Symbol Typ inches Min Max A Typ Min 5.08 0.200 A1 0.38 A2 3.56 4.06 0.140 0.160 B 0.38 0.51 0.015 0.020 – – – – C 0.20 0.30 0.008 0.012 D 41.78 42.04 1.645 1.655 B1 1.52 0.015 0.060 D2 38.10 – – 1.500 – – E 15.24 – – 0.600 – – 13.59 13.84 0.535 0.545 E1 e1 2.54 – – 0.100 – – eA 15.24 – – 0.600 – – eB 15.24 17.78 0.600 0.700 L 3.18 3.43 0.125 0.135 S 1.78 2.03 0.070 0.080 α 0° 10° 0° 10° N 32 32 Figure 12. PDIP32 - 32 lead Plastic DIP, 600 mils width, Package Outline A2 A1 B1 B A L e1 α eA D2 C eB D S N E1 E 1 PDIP Drawing is not to scale. 20/21 Max M29F040B Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in lif e support devices or systems without express written approval of STMicroelectronics. The ST logo is registered trademark of STMicroelectronics 1999 STMicroelectronics - All Rights Reserved All other names are the property of their respective owners. STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - U.S.A . http://w ww.st.com 21/21