EB4 Vishay Dale Edgeboard Connectors, Dual Readout, 0.100" (2.54 mm) C-C, Standard and Right Angle Terminals FEATURES ELECTRICAL SPECIFICATIONS Current Rating: 3 A Test Voltage Between Contacts: At sea level: 650 VRMS At 70 000 feet (21 336 meters): 275 VRMS Insulation Resistance: 5000 MΩ minimum at 500 VDC potential Contact Resistance: 30 mV maximum at rated current (with gold plating) Operating Temperature: - 65 °C to + 125 °C Humidity: 96 h at 90 % relative humidity at + 40 °C, dried at room temperature for 3 h minimum, insulation resistance was greater than 5000 MΩ Durability: After 500 cycles of insertion and withdrawal of a 0.070" (1.78 mm) thick steel test board, contact resistance less than 0.030 V at 3 A on gold plated contacts and individual contact pair separation force when measured with a 0.054" (1.37 mm) thick steel test blade was greater than ½ oz. Shock: Three 50G shocks in each of 3 mutually perpendicular planes with no loss of continuity Vibration: 2 h in each of 3 mutually perpendicular planes, frequency sweep 10 cps to 55 cps at 0.06 double amplitude with no loss of continuity • Grid Patterns: 0.100" C-C x 0.150" (2.54 mm x 3.81 mm) and 0.100" C-C x 0.200" (2.54 mm x 5.08 mm) • Standard and right angle terminals • Greater design latitude: 4 body materials: Diallyl phthalate, phenolic, glass-filled polyester and glass-filled polyphenylene sulfied 7 contact termination styles - 3 standard, 4 right angle 20 body sizes and 6 mounting styles • Selective gold plating • Accepts PC board thickness of 0.054" to 0.071" (1.37 mm to 1.80 mm) • Polarization between contact positions in all sizes. Between contact polarization permits polarizing without loss of contact position. • Recognized under the Component Program of Underwriters Laboratories, Inc. listed under file E65524, project 77CH3889 APPLICATIONS For use with 0.0625" (1.59 mm) printed circuit boards requiring an edgeboard type connector on 0.100" (2.54 mm) centers MATERIAL SPECIFICATIONS Body Material: “1” glass-filled diallyl phthalate per MIL-M-14, Type SDG-F green, flame retardant (UL 94 V-0) “2” glass-filled phenolic per MIL-M-14, Type MFH dark green, flame retardant (UL 94 V-0) “3” thermoplastic polyester, glass-filled, black, flame retardant (UL 94 V-0) ”5” thermoplastic polyphenylene sulfied, glass filled, brown, flame retardant (UL 94 V-0) Contacts: Phosphor bronze (See Ordering Information) Polarizing Key: Glass reinforced nylon, flame retardant (UL 94H-B) Plating: Gold (See Ordering Information) ORDERING INFORMATION EB4 MODEL 3 K 20 SG X 15 MOUNTING POLARIZING CONTACT PLATING STANDARD CONTACTS VARIATIONS PER SIDE TERMINAL KEY POSITIONS SG = Selective gold plating (0.00003" VARIATIONS 6, 10, 12, (0.000762 mm) minimum thick) on contact Key(s) are located to 1 = Diallyl area with gold flash on terminal. 15, 18, 20, C, D, K, right of position(s) Phthalate SGF = Selective gold plating (0.000010" 22, 25, 28, 1R, 2R, designated. Use odd2 = Phenolic 30, 31, 35, (0.000254 mm) minimum thick) on contact 3R, 4R numbered contact for 3 = Glass-filled area with gold flash on terminal. 36, 40, 43, ordering: -1, -3, -5, etc. Polyester All gold plating over 0.00005" 44, 48, 49, Required only when 5 = Glass-filled (0.00127 mm) minimum nickel underplate. 50, 60, polarizing keys are to be Polyphenylene Contact factory for additional plating and 65 factory installed. Sulfied options. Note: To order polarizing keys individually, specify model PK-4. BODY MATERIAL www.vishay.com 2 For technical questions, contact: [email protected] Document Number: 36001 Revision: 16-Feb-09 EB4 Edgeboard Connectors, Dual Readout, 0.100" (2.54 mm) C-C, Standard and Right Angle Terminals Vishay Dale DIMENSIONS in inches (millimeters) 0.060 (1.52) R Typ. 0.342 (8.69) Typ. 0.050 (1.27) Typ. 0.287 (7.29) A B C 0.100 (2.54) Typ. D E J J 0.060 (1.52) Typ. 0.054 - 0.071 (1.37 - 1.80) Card Thickness 0.125 (3.17) Point of Contact See table for contact and mounting variations 0.250 (6.35) Typ. Section J - J 0.180 (4.57) Typ. 0.430 (10.92) Typ. 0.610 (15.49) Typ. 0.300 (7.62) Depth of Insertion 0.365 (9.27) 0.150 (3.81) Polarizing Key: When ordering polarizing keys individually, 0.295 specify by the Model Number: (7.49) PK-4 between contacts. Hand insertion tool, TPK-4, provided upon request. 0.200 (5.08) # OF CONTACT POSITIONS PER SIDE 0.031 (0.787) 0.096 ± 0.002 (2.44 ± 0.051) A B C D E 6 1.435 (36.45) 1.175 (29.85) 0.700 (17.78) 0.860 (21.84) 0.750 (19.05) 10 1.835 (46.61) 1.575 (40.00) 1.100 (27.94) 1.260 (32.00) 1.150 (29.21) 12 2.035 (51.69) 1.775 (45.08) 1.300 (33.02) 1.460 (37.08) 1.350 (34.29) 15 2.335 (59.31) 2.075 (52.70) 1.600 (40.64) 1.760 (44.70) 1.650 (41.91) 18 2.635 (66.93) 2.375 (60.32) 1.900 (48.26) 2.060 (52.32) 1.950 (49.53) 20 2.835 (72.01) 2.575 (65.40) 2.100 (53.34) 2.260 (57.40) 2.150 (54.61) 22 3.035 (77.09) 2.775 (70.48) 2.300 (58.42) 2.460 (62.48) 2.350 (59.69) 25 3.335 (84.71) 3.075 (78.10) 2.600 (66.04) 2.760 (70.10) 2.650 (67.31) 28 3.635 (92.33) 3.375 (85.72) 2.900 (73.66) 3.060 (77.72) 2.950 (74.93) 30 3.835 (97.41) 3.575 (90.80) 3.100 (78.74) 3.260 (82.80) 3.150 (80.01) 31 3.935 (99.95) 3.675 (93.34) 3.200 (81.28) 3.360 (85.34) 3.250 (82.55) 35 4.335 (110.11) 4.075 (103.50) 3.600 (91.44) 3.760 (95.50) 3.650 (92.71) 36 4.435 (112.65) 4.175 (106.04) 3.700 (93.98) 3.860 (98.04) 3.750 (95.25) 40 4.835 (122.81) 4.575 (116.20) 4.100 (104.14) 4.260 (108.20) 4.150 (105.41) 43 5.135 (130.43) 4.875 (123.82) 4.400 (111.76) 4.560 (115.82) 4.450 (113.03) 44 5.235 (132.97) 4.975 (126.36) 4.500 (114.30) 4.660 (118.36) 4.550 (115.57) 48 5.635 (143.13) 5.375 (136.52) 4.900 (124.46) 5.060 (128.52) 4.950 (125.73) 49 5.735 (145.67) 5.475 (139.06) 5.000 (127.00) 5.160 (131.06) 5.050 (128.27) 50 5.835 (148.21) 5.575 (141.60) 5.100 (129.54) 5.260 (133.60) 5.150 (130.81) 60 6.835 (173.61) 6.575 (167.00) 6.100 (154.94) 6.260 (159.00) 6.150 (156.21) 65 7.335 (186.31) 7.075 (179.70) 6.600 (167.64) 6.760 (171.70) 6.650 (168.91) Document Number: 36001 Revision: 16-Feb-09 For technical questions, contact: [email protected] www.vishay.com 3 EB4 Vishay Dale Edgeboard Connectors, Dual Readout, 0.100" (2.54 mm) C-C, Standard and Right Angle Terminals PHYSICAL SPECIFICATIONS Type “3R” - dip solder, 0.025" (0.635 mm) square terminals, 0.180" (4.57 mm) nominal terminal length x 0.150" (3.81 mm) nominal terminal row spacing Contact Type: Bifurcated cantilever beam Number of Contacts: 10, 12, 15, 18, 20, 22, 25, 28, 30, 31, 35, 36, 40, 43, 44, 48, 49, 50, 60 and 65 per side Type “4R” - dip solder, 0.025" (0.635 mm) square terminals, 0.180" (4.57 mm) nominal terminal length x 0.200" (5.08 mm) nominal terminal row spacing Contact Terminal Variation: Standard terminals Type “C” - dip solder, 0.025" (0.635 mm) square terminals, 0.175" (4.44 mm) nominal terminal length below standoffs Contact Spacing: 0.100" (2.54 mm) center to center Type “D” - dip solder, 0.025" (0.635 mm) square terminals, 0.115" (2.92 mm) nominal terminal length below standoffs Contact Terminal Row Spacing: Standard - 0.200" (5.08 mm) nominal. Right angle - 0.200" (5.08 mm) nominal and 0.150" (3.81 mm) nominal Type “K” - Wire Wrap™, 0.025" (0.635 mm) square terminals, 0.570" (14.48 mm) nominal terminal length below standoffs Card Thickness: 0.054" to 0.071" (1.37 mm to 1.80 mm) Contact Terminal Variation: Right angle terminals Card Slot Depth: 0.300" (7.62 mm) Type “1R” - dip solder, 0.025" (0.635 mm) square terminals, 0.120" (3.05 mm) nominal terminal length x 0.150" (3.81 mm) nominal terminal row spacing Connector Polarization: Between contact polarization key(s) are located to the right of the contact position(s) designated Type “2R” - dip solder, 0.025" (0.635 mm) square terminals, 0.120" (3.05 mm) nominal terminal length x 0.200" (5.08 mm) nominal terminal row spacing Note • High temperature burn-in, edgeboard connectors, with 0.100" (2.54 mm) center to center are on www.vishay.com/doc?36006 MOUNTING VARIATIONS in inches (millimeters) Type “X” Clearance Hole Raised Mounting Flange Type “XF” Clearance Hole Flush Mounting Flange 0.060 (1.52) Ref. Type “XFS” Right Angle Mounting Flange 0.060 (1.52) Ref. 0.060 (1.52) Ref. 0.060 (1.52) Ref. 0.125 (3.17) Dia. 0.125 (3.17) Dia. 0.430 (10.92) Type “XS” Right Angle Mounting Flange 0.125 (3.17) Dia. 0.250 (6.35) 0.610 (15.49) Ref. Type “Y” Threaded Insert Raised Mounting Flange 0.250 (6.35) 0.125 (3.17) 0.250 (6.35) 0.610 (15.49) Ref. 0.610 (15.49) Ref. Type “W” No Mounting Flange Type “YF” Threaded Insert Flush Mounting Flange 0.060 (1.52) Ref. 0.060 (1.52) Ref. 0.060 (1.52) Ref. 0.180 (4.57) 4-40 UNC-2B 0.430 (10.92) 0.125 (3.17) 0.430 (10.92) 0.250 (6.35) 0.610 (15.49) Ref. 0.125 (3.17) Dia. 0.250 (6.35) 4-40 UNC-2B 0.610 (15.49) Ref. 0.610 (15.49) Ref. 0.430 (10.92) 0.610 (15.49) Ref. 0.250 (6.35) TERMINAL VARIATIONS in inches (millimeters) Type “C” and “D” Solder Dip, Standard 0.025 (0.635) Square Terminals 0.200 (5.08) Type “K” Wire Wrap™, Standard 0.025 (0.635) Square Terminals 0.200 (5.08) To Fit 0.050 ± 0.002 (1.27 ± 0.051) Dia. Eyelet “C” = 0.175 (4.44) “D” = 0.115 (2.92) www.vishay.com 4 Type “1R”, “2R”, “3R” and “4R” Right Angle 0.025 (0.635) Square Terminals B 0.150 0.120 ± 0.030 (3.81) (3.05 ± 0.762) 2R 0.200 0.120 ± 0.030 (5.08) (3.05 ± 0.762) 3R 0.150 0.180 ± 0.030 (3.81) (4.57 ± 0.762) 4R 0.200 0.180 ± 0.030 (5.08) (4.57 ± 0.762) A For technical questions, contact: [email protected] A 1R B 0.590 (14.99) 0.570 (14.48) TYPE Document Number: 36001 Revision: 16-Feb-09 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000