13 0PWC

Hebei I.T. (Shanghai) Co., Ltd.
LED SPECIFICATION
Part No./型号：
¾ Features/特征：
13 0PWC
¾ Descriptions/描述：
z Single color/特征
z Dice material/芯片材质：InGaN
z High bright output/高亮度输出
z Emitting Color/发光颜色：
z Low power consumption/低功耗
Super Bright White/高亮度白色
z High reliability and long life/可靠性
z Device Outline/产品外形：
高、寿命长
Special Type/ 特殊形状
2.4±0.2
z Lens Type/胶体颜色：Water Clear/无色透明
.2
±0
2.4±0.2
3.3±0.2
1.0Max
25.4min
CATHODE
1.6±0.2
3±0.2
8
1.
.2
7±0
R1.
0.5±0.2
1±0.2
2.54±0.2
NOTE/注意:
z
z
All dimensions are millimeters/单位：mm
Tolerance is +/-0.25mmunless otherwise noted/没有标注的公差为±0.25mm
www.ledz.com
Rev ：B/3
Page: 1 of 11
Hebei I.T. (Shanghai) Co., Ltd.
LED SPECIFICATION
Part No./型号：
13 0PWC
Absolute maximum ratings/极限参数（Ta = 25℃）
Parameter
参数
Reverse Voltage
反向电压
Forward Current
正向工作电流
Power Dissipation
损耗功率
Pulse Current
正向峰值电流
Operating Temperature
工作温度范围
Storage Temperature
储存温度范围
Value 数值
Unit
Symbol
符号
Test Condition
测试条件
Min.
Max.
单位
VR
IR = 30μA
5
--
V
IF
----
----
25
mA
Pd
----
----
90
mW
Ipeak
Duty=0.1mS，1kHz
----
100
mA
Topr
----
-40
+85
℃
Tstr
----
-40
+100
℃
¾ Electrical and optical characteristics /光电参数（Ta = 25℃）
Parameter
参数
Forward Voltage
正向电压
Reverse Current
反向电流
Luminous Intensity
发光强度
Viewing Angle
指向角度
Value 数值
Unit
Symbol
符号
Test Condition
测试条件
Min.
Typ.
Max.
单位
VF
IF = 20mA
----
3.2
3.6
V
IR
VR = 5V
----
----
30
μA
IV
IF = 20mA
----
4000
----
mcd
2θ1/2
IF = 20mA
----
----
----
Deg.
¾ Luminous Intensity Bins Chart/发光强度分档（Ta = 25℃）
Bin
V
W
X
Y
Min
2000
3000
4000
6000
Max
3000
4000
6000
8000
www.ledz.com
Rev ：B/3
Page: 2 of 11
Hebei I.T. (Shanghai) Co., Ltd.
LED SPECIFICATION
Part No./型号：
¾ Chromaticity Coordinates Ranks /色坐标分档(IF=20mA
Wa1
Wa3
Wa5
Wa7
Wa9
Wa11
Wb1
Wb3
Wb5
Wb7
Wb9
Wb11
Wc1
Wc3
Wc5
Wc7
Wd1
Wd3
X
Y
X
Y
X
Y
X
Y
X
Y
X
Y
X
Y
X
Y
X
Y
X
Y
X
Y
X
Y
X
Y
X
Y
X
Y
X
Y
X
Y
X
Y
www.ledz.com
0.2217
0.2114
0.2399
0.2018
0.2389
0.2209
0.2387
0.2427
0.2553
0.2276
0.2571
0.2531
0.2596
0.2811
0.2748
0.2610
0.2759
0.2857
0.2791
0.3138
0.2901
0.2870
0.2940
0.3138
0.3008
0.3398
0.3048
0.3209
0.3197
0.3589
0.3214
0.3352
0.3381
0.3740
0.3371
0.3493
0.2301
0.2271
0.2476
0.2147
0.2469
0.2352
0.2491
0.2619
0.2651
0.2443
0.2672
0.2711
0.2693
0.2974
0.2825
0.2740
0.2846
0.3004
0.2899
0.3268
0.2981
0.3007
0.3035
0.3272
0.3197
0.3589
0.3214
0.3352
0.3381
0.3740
0.3371
0.3493
0.3475
0.3817
0.3452
0.3558
0.2389
0.2209
0.2567
0.2083
0.2553
0.2276
0.2571
0.2531
0.2731
0.2355
0.2748
0.2610
0.2759
0.2857
0.2890
0.2623
0.2901
0.2870
0.2940
0.3138
0.3032
0.2845
0.3062
0.3144
0.3205
0.3481
0.3221
0.3261
0.3376
0.3616
0.3366
0.3369
0.3463
0.3687
0.3440
0.3428
0.2309
0.2065
0.2496
0.1967
0.2476
0.2147
0.2469
0.2352
0.2637
0.2200
0.2651
0.2443
0.2672
0.2711
0.2824
0.2510
0.2825
0.2740
0.2846
0.3004
0.2957
0.2737
0.2981
0.3007
0.3028
0.3304
0.3068
0.3113
0.3206
0.3461
0.3222
0.3243
0.3376
0.3616
0.3366
0.3369
X
Y
X
Wa4
Y
X
Wa6
Y
X
Wa8
Y
X
Wa10
Y
X
Wa12
Y
X
Wb2
Y
X
Wb4
Y
X
Wb6
Y
X
Wb8
Y
X
Wb10
Y
X
Wb12
Y
X
Wc2
Y
X
Wc4
Y
X
Wc6
Y
X
Wc8
Y
X
Wd2
Y
X
Wd4
Y
Wa2
Rev ：B/3
0.2309
0.2065
0.2301
0.2271
0.2476
0.2147
0.2469
0.2352
0.2491
0.2619
0.2651
0.2443
0.2672
0.2711
0.2693
0.2974
0.2825
0.2740
0.2846
0.3004
0.2899
0.3268
0.2981
0.3007
0.3028
0.3304
0.3068
0.3113
0.3206
0.3461
0.3222
0.3243
0.3376
0.3616
0.3366
0.3369
13 0PWC
Ta=25℃)
0.2389
0.2209
0.2386
0.2428
0.2553
0.2276
0.2571
0.2531
0.2596
0.2811
0.2748
0.2610
0.2759
0.2857
0.2791
0.3138
0.2901
0.2870
0.2940
0.3138
0.3008
0.3398
0.3062
0.3144
0.3205
0.3481
0.3221
0.3261
0.3376
0.3616
0.3366
0.3369
0.3463
0.3687
0.3440
0.3428
0.2476
0.2147
0.2469
0.2352
0.2636
0.2201
0.2651
0.2443
0.2672
0.2711
0.2824
0.2510
0.2825
0.2740
0.2846
0.3004
0.2957
0.2737
0.2981
0.3007
0.3035
0.3272
0.3103
0.2947
0.3214
0.3352
0.3229
0.3130
0.3371
0.3493
0.3361
0.3241
0.3452
0.3558
0.3427
0.3284
0.2399
0.2018
0.2389
0.2209
0.2567
0.2083
0.2553
0.2276
0.2571
0.2531
0.2731
0.2355
0.2748
0.2610
0.2759
0.2857
0.2890
0.2623
0.2901
0.2870
0.2940
0.3138
0.3032
0.2845
0.3048
0.3209
0.3103
0.2947
0.3214
0.3352
0.3229
0.3130
0.3371
0.3493
0.3361
0.3241
Page: 3 of 11
Hebei I.T. (Shanghai) Co., Ltd.
LED SPECIFICATION
Part No./型号：
Wd5
Wd7
X
Y
X
Y
0.3475
0.3817
0.3452
0.3558
0.3569
0.3894
0.3533
0.3624
0.3551
0.3760
0.3515
0.3487
0.3463
Wd6
0.3687
0.3440
Wd8
0.3428
X
Y
X
Y
13 0PWC
0.3463
0.3687
0.3440
0.3428
0.3551
0.3760
0.3515
0.3487
0.3533
0.3624
0.3494
0.3328
0.3452
0.3558
0.3427
0.3284
CIE 1931 Chromaticity diagram
wb
wb10
wb11
wb7
wb
wb5
wb9
wb1
wb6
wb2
wa
wa10
wb12
wb8
wb4
wb3
wa11
wa12
wa7
wa
wa8
wa9
wa4
wa5
wa6
wa1
wa2
wa3
www.ledz.com
Rev ：B/3
Page: 4 of 11
Hebei I.T. (Shanghai) Co., Ltd.
LED SPECIFICATION
Part No./型号：
13 0PWC
wf
wf6
we
wf1
wf7
we5
wd
we1
wd6
wc
wc5
we7 wf4
we3
wd2
wc6
wd3
wf9
wf10
wf5
wd7
wc1
wf3
we2
wd1
wf8
we6
wd5
wc
wf2
we8
we4
wd8
wc2
wc3
wc7
wd4
wc8
wc4
www.ledz.com
Rev ：B/3
Page: 5 of 11
Hebei I.T. (Shanghai) Co., Ltd.
LED SPECIFICATION
Part No./型号：
13 0PWC
¾ Typical electrical/optical characteristic curves/光电特性曲线：
Fig.1 正向电流 Vs. 正向电压
Fig.2 相对亮度 Vs. 正向电流
2.5
Luminous Intensity
Relative Value at IF=20mA
Forward Current(mA)
50
40
30
20
10
0
2.6
2.8 3.0 3.2 3.4
Forward Voltage(V)
Relative Luminous Intensity
Forward Current(mA)
30
20
10
0
0
20
40
80
60
1.0
0.5
0
40
10
20
30
IF-Forward Current (mA)
50
Fig.4 相对亮度 Vs. 环境温度
Fig.3 正向电流 Vs. 环境温度
40
1.5
0
3.6
50
2.0
2.5
2.0
1.5
1.0
0.5
0
-40
100
-20
40
60
0
20
Ambient Temperature TA (℃)
Ambient Temperature TA (℃)
80 90
Relative Luminous Intensity
F ig .5 相 对 亮 度 V s 波 长
1.2
Ta=25℃
1.0
0.8
0.6
0.4
0.2
0
400
450
500
550
Wavelength
www.ledz.com
600
650
700
(nm)
Rev ：B/3
Page: 6 of 11
Hebei I.T. (Shanghai) Co., Ltd.
LED SPECIFICATION
Part No./型号：
13 0PWC
¾ Relibility Analysis/可靠性试验
The reliability of products shall be satisfied with items listed below/产品的可靠性应该满足下面
列表项目：
Confidence level:90% ；LTPD :10%
z Test Items And Results/测试项目和判据
No.
Item/项目
Test Condition/测试条件
Time/
时间
Q’ty/数量
1
Resistance to
Soldering Heat /
抗焊接热
Tsld=235±5℃，5sec 3mm from
the base of the epoxy bulb
1 time
25
ALL PASS
2
Solder ability/可焊性
Tsld=235±5℃，5sec
1times
Over 95%
25
ALL PASS
3
Temperature Cycle/
高低温循环
-40℃—— 100℃
30min ~ 30min
The cut is not more than 2 min
50cycles
100
ALL PASS
4
High Temperature
/High Humidity /
高温高湿
85℃/85%RH
1000hrs
100
ALL PASS
5
High Temperature
Storage /高温储存
Ta=100℃
1000hrs
100
ALL PASS
6
Low Temperature
Storage /低温储存
Ta=-40℃
1000hrs
100
ALL PASS
7
DC Operation Life /
寿命测试
IF=20mA
1000hrs
25
ALL PASS
Standard/判定
z Criteria For Judging Damage/判断标准
Symbol/
符号
Test conditions
/测试条件
Luminous Intensity/亮度
Iv
Forward Voltage/正向电压
Reverse current/反向电流
Item/项目
Criteria for Judgement
/判断标准
Min./最小值
Max./最大值
IF=20mA
Iv*0.7
/
VF
IF=20mA
/
U.S.L*1.1
IR
VR=5v
/
U.S.L*2
*U.S.L.：Upper Standard Level / 上限
*L.S.L.：Lower Standard Level / 下限
www.ledz.com
Rev ：B/3
Page: 7 of 11
Hebei I.T. (Shanghai) Co., Ltd.
LED SPECIFICATION
Part No./型号：
13 0PWC
¾ Label Form Specification/标签格式规范
P/N：
Rank ：
Qty：
Date：
Lot No：
/
/
pcs QC：
P/N: Customer's Production Number/产品编号
QTY: Packing Quantity/包装数量
Ranks: Iv / Vf / WD
Iv：Iv Rank/亮度；Vf：Vf Rank/电压；WD：Color Group/色系
QC: Quality Control chapter/质量控制章
Date: mm / dd / yy
mm：Month/月；dd：Date/日；yy：Year/年；
Lot No: Production batch Number/生产批号
¾ Lead Forming/成形
1. Any lead forming or bending must be done before soldering.
支架成形必须在焊接前完成。
2. When forming leads, there must be a minimum of 2mm clearance between the base of the LED lens and
the lead bend.
必需离胶体 2 毫米才能折弯支架。
www.ledz.com
Rev ：B/3
Page: 8 of 11
Hebei I.T. (Shanghai) Co., Ltd.
LED SPECIFICATION
Part No./型号：
13 0PWC
3. Avoid bending the leads at the same point more than once.
避免在管脚同一位置两次或多次弯。
4. During assembly onto PCB, the lead pitch of the LED must match the pitch of the mounting holes on
the PCB during component placement.
支架成形需保证引脚和间距与线路板上一致。
5. Recommendations for manual plug-in operation, if really need taping machine for inserting operation,
please make small batch prenatal confirmation.
建议手工插件作业，若确实需要编带机插作业，请进行小批量产前确认。
¾ Soldering Condition/焊接条件
Careful attention should be paid during soldering. When soldering, leave more then 2mm from solder joint
to case, and soldering beyond the base of the tie bar is recommended.
焊接时请特别注意，焊接点要离LED封装体底部2mm以上。
Avoiding applying any stress to the lead frame while the LEDs are at high temperature particularly when
soldering.
在 LED 处于高温，特别是在焊接时，请避免对支架施压。
Recommended soldering conditions/推荐焊接条件:
Hand Soldering
DIP Soldering
手工焊接
浸焊
Temp.at tip of iron
电烙铁温度
300
℃
Max.(30WMax.)
Preheat temp.
100℃ Max. (60 sec Max.)
预热温度
最高温度100℃（不超过60秒）
最高温度300℃（功
率不超过30瓦）
Soldering time
3 sec Max.
Bath temp.
260℃ Max
焊接时间
时间不超过3秒
浸焊温度
最高260℃.
Distance
2mm Min.(From solder joint to
Bath time.
3 sec Max.
焊接位置
case)
浸焊时间
不超过3秒
大于2毫米（从焊点到胶体）
www.ledz.com
Distance
2mm Min
浸焊位置
大于2毫米.
Rev ：B/3
Page: 9 of 11
Hebei I.T. (Shanghai) Co., Ltd.
LED SPECIFICATION
Part No./型号：
13 0PWC
¾ Cleaning/清洗
1. Do not clean LEDs with water, Alcohol are recommended solvents for cleaning. When using other
solvents, it should be confirmed beforehand whether the solvents will dissolve the resin or not.
不要用水清洗，推荐使用酒精清洗，当使用其他溶剂清洗时应事先确认该溶剂是否溶解树脂。
2. LEDs may be damaged by ultrasonic-washed. Before cleaning, a pre-test should be done to confirm
whether any damage to the LEDs will occur.
LED有可能在超声波清洗过程中被破坏。为了保证安全，在清洗前，请先确认。
¾ Storage/保存
1. Environmental temperature: -40℃---100℃, Recommended: -20℃---50℃
环境温度：-40℃---100℃，推荐使用-20℃---50℃；
2. Environmental humidity: 30%---70%, Recommended: 40%---60%
环境湿度：30%---70%，推荐使用40%---60%；
¾ Static Electricity/静电
1. Static Electricity or power surge will damage the LED.
It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs.
静电或激增电压将损害 LED。
建议使用发光二极管时佩戴手腕带或防静电手套。
2. All production machinery and test instruments must be electrically grounded.
所有的生产机器和检测仪器，必须接地。
www.ledz.com
Rev ：B/3
Page: 10 of 11
Hebei I.T. (Shanghai) Co., Ltd.
LED SPECIFICATION
Part No./型号：
13 0PWC
3. Maintain a humidity level of 50% or higher in production areas.
生产现场湿度必须保持在50%或者更高。
4. Use anti-static packaging for transport and storage.
使用防静电包装，运输和储存。
¾ Notes/备注
1. This datasheet will be update regularly, if there comes out any changes, pls confirmed by the latest
datasheet.
以上规格书会定期进行更新，如有改动,以最新规格书为准。
2. When using this product, please observe the absolute maximum ratings and the instructions for using
outlined in these specification sheets. HB assumes no responsibility for any damage resulting from
use of the product which does not comply with the absolute maximum ratings and the instructions
included in these specification sheets.
在使用本产品时，请注意参考规格书中的最大额定值和使用说明，如果没有遵照产品规格书中的最
大额定值以及使用说明而产生的不良后果，不在承诺范围之内。
www.ledz.com
Rev ：B/3
Page: 11 of 11