Hebei IT (Shanghai) Co., Ltd. Part No.:412PWC

Hebei I.T. (Shanghai) Co., Ltd.
LED SPECIFICATION
5.8±0.2
Part No.:412PWC
¾ Features/特征:
4.8±0.2
R3,1±0,1
z Single color/特征
命长
¾ Descriptions/描述:
z Dice material/芯片材质:GaInN
1.0Max
25.4Min
z High reliability and long life/可靠性高、寿
1.5±0.5
CATHODE
4.8±0.2
z Low power consumption/低功耗
1.5±0.2
z High bright output/高亮度输出
0.5±0.1
z Emitting Color/发光颜色:
2.54±0.1
Super Bright White/高亮度白色
z Device Outline/产品外形:
NOTE/注意:
z
z
φ5mm Round Type/5mm 圆形
z Lens Type/胶体颜色:
All dimensions are millimeters/单位:mm
Tolerance is +/-0.25mmunless otherwise
noted/没有标注的公差为±0.25mm
Water Clear/无色透明
¾ Directivity/指向特性:
Relative Luminous Intensity
/相对亮度
¾
0°
1.0
Ta=25°C
IF=20mA
30°
60°
0.5
0
90°
60°
30°
0°
0.5
90°
1.0
Radiation Angle/辐射角度
www.ledz.com
1/7
Hebei I.T. (Shanghai) Co., Ltd.
LED SPECIFICATION
Part No.:412PWC
Absolute maximum ratings/极限参数(Ta = 25℃)
Parameter
参数
Value 数值
Unit
Symbol
符号
Test Condition
测试条件
Min.
Max.
单位
VR
IR = 30μA
5
--
V
IF
----
----
25
mA
Pd
----
----
90
mW
Ipeak
Duty=0.1mS,1kHz
----
100
mA
Topr
----
-40
+85
℃
Tstr
----
-40
+100
℃
Reverse Voltage
反向电压
Forward Current
正向工作电流
Power Dissipation
损耗功率
Pulse Current
正向峰值电流
Operating Temperature
工作温度范围
Storage Temperature
储存温度范围
¾ Electrical and optical characteristics /光电参数(Ta = 25℃)
Parameter
参数
Forward Voltage
正向电压
Reverse Current
反向电流
Luminous Intensity
发光强度
Viewing Angle
指向角度
Value 数值
Test Condition
测试条件
Min.
Typ.
Max.
单位
VF
IF = 20mA
----
3.2
3.6
V
IR
VR = 5V
----
----
30
μA
IV
IF = 20mA
----
1300
----
mcd
2θ1/2
IF = 20mA
----
120
----
Deg.
¾ Luminous Intensity Bins/亮度等级分档(Ta = 25℃)
Bin
Min
Max
T
1000
1500
U
1500
2000
V8
3.0
3.2
Unit:mcd
V
2000
3000
¾ Forward Current Bins/电压等级分档(Ta = 25℃)
Bin
Min
Max
Unit
Symbol
符号
V9
3.2
3.4
Unit:V
V10
3.4
3.6
www.ledz.com
2/7
Hebei I.T. (Shanghai) Co., Ltd.
LED SPECIFICATION
Part No.:412PWC
¾ Chromaticity Coordinates Ranks /色坐标分档(IF=20mA
Wa1
Wa3
Wb2
Wc2
Wc4
Wd2
X
Y
X
Y
X
Y
X
Y
X
Y
X
Y
0.243
0.200
0.246
0.236
0.264
0.267
0.287
0.295
0.306
0.332
0.330
0.360
0.215
0.230
0.230
0.250
0.248
0.286
0.283
0.305
0.298
0.350
0.321
0.379
0.230
0.250
0.248
0.286
0.275
0.321
0.330
0.360
0.321
0.379
0.366
0.419
0.263
0.220
0.264
0.267
0.283
0.305
0.330
0.339
0.330
0.360
0.361
0.385
Wa2
Wb1
Wc1
Wc3
Wd1
Wf
X
Y
X
Y
X
Y
X
Y
X
Y
X
Y
0.263
0.220
0.280
0.248
0.296
0.276
0.283
0.305
0.330
0.318
0.356
0.351
Ta=25℃)
0.246
0.236
0.264
0.267
0.287
0.295
0.275
0.321
0.330
0.360
0.366
0.419
0.264
0.267
0.283
0.305
0.330
0.339
0.298
0.350
0.361
0.385
0.391
0.436
0.280
0.248
0.296
0.276
0.330
0.318
0.306
0.332
0.356
0.351
0.380
0.381
CIE 1931 Chromaticity diagram
Y
IF=20mA ; Ta=25° C
W d2
Wf
W W
c1 c 2
W c4 W d1
W c3
W b2
W b1
W a3
W a2
W a1
x
www.ledz.com
3/7
Hebei I.T. (Shanghai) Co., Ltd.
LED SPECIFICATION
Part No.:412PWC
¾ Typical electrical/optical characteristic curves/光电特性曲线:
Fig.1 正向电流 Vs. 正向电压
Fig.2 相对亮度 Vs. 正向电流
2.5
Luminous Intensity
Relative Value at IF=20mA
Forward Current(mA)
50
40
30
20
10
0
2.6
2.8 3.0 3.2 3.4
Forward Voltage(V)
Relative Luminous Intensity
20
10
0
0
20
40
60
80
0.5
0
10
20
30
40
IF-Forward Current (mA)
50
2.5
2.0
1.5
1.0
0.5
0
-40
100
Ambient Temperature TA (℃)
Relative Luminous Intensity
Forward Current(mA)
30
1.0
Fig.4 相对亮度 Vs. 环境温度
Fig.3 正向电流 Vs. 环境温度
40
1.5
0
3.6
50
2.0
-20
40
60
0
20
Ambient Temperature TA (℃)
80 90
1.2
Ta=25℃
1.0
0.8
0.6
0.4
0.2
0
400
450
500
550
Wavelength
600
650
700
(nm)
www.ledz.com
4/7
Hebei I.T. (Shanghai) Co., Ltd.
LED SPECIFICATION
Part No.:412PWC
¾ Lead Forming/成形
1. Any lead forming or bending must be done before soldering.
支架成形必须在焊接前完成。
2. When forming leads, there must be a minimum of 2mm clearance between the base of the LED lens and
the lead bend.
必需离胶体 2 毫米才能折弯支架。
3. Avoid bending the leads at the same point more than once.
避免在管脚同一位置两次或多次弯。
4. During assembly onto PCB, the lead pitch of the LED must match the pitch of the mounting holes on
the PCB during component placement.
支架成形需保证引脚和间距与线路板上一致。
¾ Soldering Condition/焊接条件
Careful attention should be paid during soldering. When soldering, leave more then 2mm from solder joint
to case, and soldering beyond the base of the tie bar is recommended.
焊接时请特别注意,焊接点要离LED封装体底部2mm以上。
Avoiding applying any stress to the lead frame while the LEDs are at high temperature particularly when
soldering.
在 LED 处于高温,特别是在焊接时,请避免对支架施压。
www.ledz.com
5/7
Hebei I.T. (Shanghai) Co., Ltd.
LED SPECIFICATION
Part No.:412PWC
Recommended soldering conditions/推荐焊接条件:
Hand Soldering
手工焊接
Temp.at tip of iron 300℃Max.(30WMax.)
电烙铁温度
最高温度300℃(功率
不超过30瓦)
Soldering time
3 sec Max.
焊接时间
时间不超过3秒
Distance
2mm Min.(From solder
焊接位置
joint to case)
大于2毫米(从焊点到
胶体)
DIP Soldering
浸焊
Preheat temp. 100℃ Max. (60 sec Max.)
预热温度
最高温度100℃(不超过60
秒)
Bath temp.
260℃ Max
浸焊温度
最高260℃.
Bath time.
3 sec Max.
浸焊时间
不超过3秒
Distance
浸焊位置
2mm Min
大于2毫米.
¾ Cleaning/清洗
1. Do not clean LEDs with water, Alcohol are recommended solvents for cleaning. When using other
solvents, it should be confirmed beforehand whether the solvents will dissolve the resin or not.
不要用水清洗,推荐使用酒精清洗,当使用其他溶剂清洗时应事先确认该溶剂是否溶解树脂。
2. LEDs may be damaged by ultrasonic-washed. Before cleaning, a pre-test should be done to confirm
whether any damage to the LEDs will occur.
LED有可能在超声波清洗过程中被破坏。为了保证安全,在清洗前,请先确认。
¾ Storage/保存
1. Environmental temperature: -40℃---100℃, Recommended: -20℃---50℃
环境温度:-40℃---100℃,推荐使用-20℃---50℃;
2. Environmental humidity: 30%---70%, Recommended: 40%---60%
环境湿度:30%---70%,推荐使用40%---60%;
www.ledz.com
6/7
Hebei I.T. (Shanghai) Co., Ltd.
LED SPECIFICATION
Part No.:412PWC
¾ Static Electricity/静电
1. Static Electricity or power surge will damage the LED.
It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs.
静电或激增电压将损害 LED。
建议使用发光二极管时佩戴手腕带或防静电手套。
2. All production machinery and test instruments must be electrically grounded.
所有的生产机器和检测仪器,必须接地。
3. Maintain a humidity level of 50% or higher in production areas.
生产现场湿度必须保持在50%或者更高。
4. Use anti-static packaging for transport and storage.
使用防静电包装,运输和储存。
¾ Notes/备注
1. This datasheet will be update regularly, if there comes out any changes, pls confirmed by the latest
datasheet.
以上规格书会定期进行更新,如有改动,以最新规格书为准。
2. When using this product, please observe the absolute maximum ratings and the instructions for using
outlined in these specification sheets. HEBEI assumes no responsibility for any damage resulting from use
of the product which does not comply with the absolute maximum ratings and the instructions included in
these specification sheets.
在使用本产品时,请注意参考规格书中的最大额定值和使用说明,如果没有遵照产品规格书中的最
大额定值以及使用说明而产生的不良后果,不在赫备承诺范围之内。
www.ledz.com
7/7