Leaded Oscillator, OCXO Metal Package, Full Size DIP Compatible I418/I419 Series Product Features: Applications: Low Phase Noise Low Power Consumption Voltage Control High Stability Telecommunications Data Communications Instrumentation Test and Measurement Frequency 10.000 MHz- 30.000 MHz Output Level Sine HCMOS +7dBm Min., 9dBm Max. ‘0’ = 10% Vcc Max., ‘1’ = 90% VDC typ. Output Load Sine HCMOS 50 ohms 15 pf Harmonics -25 dBc Duty Cycle (HC-MOS) 50% ±5% Spurious -40 dBC Frequency Stability See Frequency Stability Table Supply Voltage See Voltage Table (±5%) Current (Warm Up) Current @ 25 C (Steady State) 110 mA Max. 23 mA Voltage Control Voltage Range Pullability Deviation Slope (Positive) Hysteresis (retrace after 30min.) 0.0 VDC Min., 5.0 VDC Max. ±1.0PPM 10% ± 20.0 ppb Allan Variance (1s) 2.00E-11 Warm Up Time 30 sec typ., 60sec max. Phase Noise - 90 dBc/Hz @ 1Hz -120 dBc/Hz @ 10Hz -145 dBc/Hz @ 100Hz -155 dBc/Hz @ 1kHz -165 dBc/Hz @ 10kHz -165 dBc/Hz @ 100kHz 0.048 7.62 8 2 1 15.24 -40 C to +85 C I418 – (Sine) I419 – (HCMOS) 14 7 Storage Input Voltage 15.1 6 Min. See Operating Temperature Table Below Package 21.85 10 Max. Operating Part Number Guide I418 Package 2.54 Pin Connection 1 Control Voltage 2 Reference Voltage 7 Gnd 8 Output 14 Vcc Dimension Units: mm Sample Part Number: I416-5AA3V-10.000 MHz Operating Temperature Output Frequency Stability (in ppm) Voltage Control 3= 3.3V 7 = 0 C to +50 C A = Sine Y = 0.5 V = Controled 5 = 5.0V 1 = 0 C to +70 C 1 = 0.25 F = Fixed 9 = 12.0V 6 = -10 C to +75 C 2 = 0.1 3 = -20 C to +70 C 3 = 0.05 Frequency -10.000 MHz A= -30 C to +70 C ILSI America Phone: 775-851-8880 • Fax: 775-851-8882• e-mail: [email protected] • www.ilsiamerica.com 8/03/11_A Specifications subject to change without notice Page 1 Leaded Oscillator, OCXO Metal Package, Full Size DIP Compatible I418/I419 Series Pb Free Solder Reflow Profile: Typical Application: *Units are backward compatible with 240C reflow processes Package Information: MSL = N.A. (package does not contain plastic, storage life is unlimited under normal room conditions). Termination = e1 (Sn / Cu / Ag over Ni over Kovar base metal). Environmental Specifications Thermal Shock Moisture Resistance Mechanical Shock Mechanical Vibration Resistance to Soldering Heat Hazardous Substance Solderability Terminal Strength Gross Leak Fine Leak Solvent Resistance MIL-STD-883, Method 1011, Condition A MIL-STD-883, Method 1004 MIL-STD-883, Method 2002, Condition B MIL-STD-883, Method 2007, Condition A J-STD-020C, Table 5-2 Pb-free devices (except 2 cycles max) Pb-Free / RoHS / Green Compliant JESD22-B102-D Method 2 (Preconditioning E) MIL-STD-883, Method 2004, Test Condition D MIL-STD-883, Method 1014, Condition C MIL-STD-883, Method 1014, Condition A2, R1=2x10-8 atm cc/s MIL-STD-202, Method 215 Marking Line 1: ILSI and Date Code Line 2: XXXXXX (Part Number detail = I418-XXXXX-Freq.) Line 2: Frequency ILSI America Phone: 775-851-8880 • Fax: 775-851-8882• e-mail: [email protected] • www.ilsiamerica.com 8/03/11_A Specifications subject to change without notice Page 2