Crane Aerospace & Electronics Power Solutions FMCE-0828 EMI Input Filters 28 Volt input – 8 Amp Features Attenuation to 60 dB at 500 kHz, typical • Operating temperature -55° to +125°C • Nominal 28 V input, -0.5 to 50 V operation • Transient rating -0.5 to 80 V for 1 second • Up to 8 A throughput current over the full input voltage range of -0.5 to 50 V • Compliant to -- MIL-STD-461C CE03 -- MIL-STD-461D, E and F CE102 -- MIL-STD-461C CS01 -- MIL-STD-461D, E and F CS101 Input Voltage and Current • Compatible with MIL-STD-704 A-E 28 VDC power bus Description Input (V) 28 Current (A) 8 Interpoint™ FMCE-0828™ EMI filters are specifically designed to reduce the reflected input ripple current of Interpoint high frequency DC/DC converters. FMCE-0828 filters minimize electromagnetic interference (EMI) for the MFL, MOR, MTR, MHV and MHF+ Series of converters. These filters are intended for use in 28 volt applications which must meet MIL-STD-461C CE03 and CS01 and/or MIL-STD-461D, E and F CE102 and CS101 levels of conducted emissions. One filter can be used with multiple converters up to the rated output current of the filter. Place the filter as close as possible to the converter for optimum performance. The baseplates of the filter and the converter should be connected with the shortest and widest possible conductors. Input Ripple and EMI The FMCE-0828 Series filters are rated for full power operation from -55°C to +125°C case temperature. Current is derated linearly to 80% at +135°C case temperature. Switching DC/DC converters naturally generate two noise components on the power input line: differential noise and common mode noise. Input ripple current refers to both of these components. Differential noise occurs between the positive input and input common. Most Interpoint converters have an input filter that reduces differential noise which is sufficient for many applications. Common mode noise occurs across stray capacitances between the converter’s power train components and the baseplate (bottom of the package) of the converter. Where low noise currents are required to meet CE03 of MIL-STD-461C and/or CE102 of ML-STD-461D, E and F, a power line filter is needed. The FMCE-0828 EMI power line filters reduce the common mode and differential noise generated by the converters. FMCE-0828 filters reduce input ripple current by 60 dB, typical, at 500 kHz and 1 MHz when used in conjunction with Interpoint DC/DC converters. Crane Aerospace & Electronics Power Solutions – Interpoint Products 10301 Willows Rd NE, Redmond, WA 98052 +1.425.882.3100 • [email protected] www.craneae.com/interpoint Transients A transient of -0.5 to 80 V (0.5 ohm source impedance) will not damage the filter but will be passed on to the converter: Operation over Temperature Insertion Loss The maximum dc insertion loss at full load and nominal input voltage represents a power loss of less than 3%. Packaging FMCE-0828 filters are sealed in metal hermetic, down-leaded packages non-flanged (case F5) or flanged (case J6). Also available in a side-leaded package (case U). Page 1 of 11 FMCE-0828 Rev J - 2011.09.08 Crane Aerospace & Electronics Power Solutions FMCE-0828 EMI Input Filters 28 Volt input – 8 Amp Operating Conditions and characteristics mechanical and environmental Size (maximum) •Case F5, down-leaded ‣‣1.945 x 1.350 x 0.405 inches (49.40 x 34.29 x 10.29 mm) •Case J6, down-leaded flanged ‣‣2.720 x 1.350 x 0.405 inches (69.09 x 34.29 x 10.29 mm). •Case U, side-leaded ‣‣3.005 x 1.505 x 0.400 inches (76.33 x 38.23 x 10.16 mm) Input Voltage Range •Continuous -0.5 to 50 VDC •Transient -0.5 to 80 V for 1 second Lead Soldering Temperature (10 sec per lead) •300°C Storage Temperature Range (Case) •-65°C to +150°C Weight (maximum) •60 grams cases F5 and J6 •86 grams typical case U Case Operating Temperature (TC) •-55°C to +125°C full power •-55°C to +135°C absolute Screening The FMCE-0828 EMI Input filter offers Standard, /ES or 883, Class H, QML screening. See Screening Tables 1 and 2 for more information. Derating Input/Output Current •Linearly from 100% at 125°C to 80% at 135° C Isolation (TC = 25°C) •100 megohm minimum at 500 VDC Electrostatic Discharge (ESD) Sensitivity per MIL-PRF-38534 •Classification 3B, 8000 V EMI FILTER +Vin DC/DC CONVERTER +Vin +Vout +Vout Case Output Input Common Common Case Output Input Common Common Chassis ground Multiple units allowed up to rated output current of filter RL RL The case ground connection between the filter and the converter should be as low an impedance as possible to minimize EMI. Direct contact of baseplate to chassis ground provides the lowest impedance. Figure 1: Connection Diagram Positive Output Positive Input Output Common Input Common Figure 2: Schematic FMCE-0828 www.craneae.com/interpoint Page 2 of 11 FMCE-0828 Rev J - 2011.09.08 Crane Aerospace & Electronics Power Solutions FMCE-0828 EMI Input Filters 28 Volt input – 8 Amp Pin Out down-Leaded Model Pin Squared corner and dot on top of package indicate pin one. PIN OUT Designation 1 Positive Input 3 Output Common 2 1 Positive Output 4 Case Ground 5 2 BOTTOM VIEW FMCE-0828 See case F5 and J6 for dimensions. 1 5 Input Common Note 1. Although the down-leaded packages can be connected to chassis ground with the case ground lead, direct contact of the base plate to chassis improves EMI performance. 4 3 Dotted line shows flanged package option. Figure 3: Pin Out FMCE-0828 Pin Out Side-Leaded model Pin PIN OUT 1, 2, 3 4, 5, 6 7, 8, 9 10, 11, 12 Bottom of case Angled corner and cover marking indicate pin one. Designation Positive Input 12 Input Common 2 11 3 Positive Output 4 Outline shown is case U. Designator “SL” is required in Case Option position of model number 9 5 8 6 7 Output Common Case Ground Notes 1. All pins must be connected. 2. The baseplate is the only case ground connection and should directly contact chassis ground. www.craneae.com/interpoint TOP VIEW FMCE-0828 1 10 Figure 3: Pin Out FMCE-0828-SL Page 3 of 11 FMCE-0828 Rev J - 2011.09.08 Crane Aerospace & Electronics Power Solutions FMCE-0828 EMI Input Filters 28 Volt input – 8 Amp model numbering key Base Model FMCE - 08 28 - F DSCC Numbers DSCC Drawing (5915) / 883 Output Current Input Voltage Case Option (Down-leaded non-flanged case has no designator in this position) FMCE-0828 Similar Part 10017-01HXC FMCE-0828/883 10017-01HZC FMCE-0828-F/883 For exact specifications for a DSCC product, refer to the DSCC drawing. DSCC drawings can be downloaded from: http://www.dscc.dla.mil/programs/smcr Screening (Standard screening has no designator in this position.) *Case/Lead Option: F5 down-leaded (case option is left blank), case J6 downleaded flanged (case option “F”), case U side-leaded (case option is “SL”). On Category Selection model selection the lines below, enter one selection from each category to determine the model number. FMCE-0828 Base Model and Input Voltage “FMCE-0828” is the only available selection – _______ / ______ Case/Lead option 1 Screening 2 (NON-FLANGED, DOWN-LEADED leave blank) Standard (leave blank) F (down-leaded flanged) ES SL (case U, side-leaded) 883 (Class H, QML, not available for SL option) Notes: 1. Case F5 is the standard, down-leaded case. Leave the option blank for case F5. Refer to the case drawings for other case options. 2. Leave blank for standard screening. Use “ES” for “ES” screening and “883” for Class H screening. See screening Tables 1 and 2 for more information. www.craneae.com/interpoint Page 4 of 11 FMCE-0828 Rev J - 2011.09.08 Crane Aerospace & Electronics Power Solutions FMCE-0828 EMI Input Filters 28 Volt input – 8 Amp Electrical Characteristics: -55° to +125°C TC, nominal Vin, unless otherwise specified. MODEL FMCE-0828 Case F5 or J6 PARAMETER CONDITIONS INPUT VOLTAGE CONTINUOUS TRANSIENT, 1 sec NOISE REJECTION DC RESISTANCE (RDC) AT MAXIMUM CURRENT CAPACITANCE OUTPUT VOLTAGE 3 OUTPUT CURRENT POWER DISSIPATION AT MAXIMUM CURRENT 1 1, 2 FMCE-0828 Case U MIN TYP MAX MIN TYP MAX UNITS -0.5 28 50 -0.5 28 50 VDC V -0.5 — 80 -0.5 — 80 500 kHz 50 60 — 50 60 — 1 MHz 50 60 — 50 60 — — 0.080 0.100 — 0.080 0.125 — 0.095 0.110 — — — 50,000 60,000 70,000 50,000 60,000 70,000 25°C TC = -55 AND +125°C ANY PIN TO CASE TC = 25°C STEADY STATE 1 VOUT = VIN - IIN (RDC) STEADY STATE VIN = 0 - 50 VDC — — 5.1 6.4 — 5.1 7.8 TC = 125°C — 6.1 7.0 — 6.1 8.6 TC = 25°C — 8 Note 1. Guaranteed by design, not tested. 2. 0.5 ohm source impedance 3. Typical applications result in VOUT within 3% of VIN. www.craneae.com/interpoint VOUT = VIN - IIN (RDC) Page 5 of 11 FMCE-0828 Rev J - 2011.09.08 — — 8 dB ohms pF VDC A W Crane Aerospace & Electronics Power Solutions FMCE-0828 EMI Input Filters 28 Volt input – 8 Amp Typical Performance Curves: 25°C TC, nominal Vin, unless otherwise specified. 80 CE 03 70 60 90 MIL-STD-461C POWER IN LIMITS EMISSION LEVEL (dB µA) EMISSION LEVEL (dB µA) 90 NARROWBAND LIM IT 50 40 30 20 10 0 .015 0.1 10 1 FREQUENCY (MHz) 80 MIL-STD-461C POWER IN LIMITS CE 03 70 60 NARROWBAND LIM IT 50 40 30 20 10 0 50 0.1 .015 Three paralleled and synchronized MFL2815D converters without filtering. 1 FREQUENCY (MHz) 10 50 CE03: Three paralleled and synchronized MFL28 converters with an FMCE-0828. Figure 6 Figure 5 EMISSION LEVEL (dB µV) 100 90 CE1 02 A 80 70 Ca nd D CL imit s 60 50 40 30 20 10 .01 0.1 1 10 FREQUENCY (MHz) CE102: Three paralleled and synchronized MFL28 converters with an FMCE-0828. Figure 7 10 1.6 1.4 ATTENUATION (dB) IMPEDANCE (OHMS) 2.0 1.8 1.25 1.2 1.0 0.8 0.6 0.4 0.2 0.1 1.0 10 26 FREQUENCY (kHz) -10 -30 -50 -70 100 1 FMCE-0828 Output Impedance (measured at the output with input pins shorted) 100 FREQUENCY (kHz) FMCE-0828 Attenuation Figure 9 Figure 8 www.craneae.com/interpoint 10 Page 6 of 11 FMCE-0828 Rev J - 2011.09.08 1M Crane Aerospace & Electronics Power Solutions FMCE-0828 EMI Input Filters – Cases 28 Volt input – 8 Amp BOTTOM VIEW CASE F5 Squared corner and dot on top of case indicates pin one 1.350 max. (34.29) 1.170 (29.72) 5 0.170 (4.32) 2 4 3 1.770 (44.96) 1 0.040 dia. (1.02) 1.370 (34.80) Seam Seal Case dimensions in inches (mm) Tolerance ±0.005 (0.13) for three decimal places ±0.01 (0.3) for two decimal places unless otherwise specified 1.945 max. (49.40) 0.000 0.170 (4.32) 0.25 (6.4) 0.000 0.405 max (10.29) 0.000 CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300°C for 10 seconds per pin. Materials Header Cold Rolled Steel/Nickel/Gold Cover Kovar/Nickel Pins #52 alloy/Gold ceramic seal Seal hole 0.120 ±0.002 (3.05 ± 0.05) Case F5 FMCE-0828, Rev D, 20100429 Please refer to the numerical dimensions for accuracy. Figure 11: Case F5 www.craneae.com/interpoint Page 7 of 11 FMCE-0828 Rev J - 2011.09.08 Crane Aerospace & Electronics Power Solutions FMCE-0828 EMI Input Filters – Cases 28 Volt input – 8 Amp BOTTOM VIEW CASE J6 Flanged cases: Designator "F" required in Case Option position of model number. Dot on top of case indicates pin one. Seam Seal 1.350 max. (34.29) 1.170 (29.72) 1 0.040 dia. (1.02) 2 x Dia 0.162 ±0.002 (4.11 ±0.05) 2 2 x R 0.170 (4.32) 4 3 1.770 (44.96) 5 0.170 (4.32) 1.370 (34.80) 0.670 (17.02) (2.720 max (69.09)) Flange thickness: 0.060 (1.52) Case dimensions in inches (mm) Tolerance ±0.005 (0.13) for three decimal places ±0.01 (0.3) for two decimal places unless otherwise specified CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300°C for 10 seconds per pin. Materials Header Cold Rolled Steel/Nickel/Gold Cover Kovar/Nickel Pins #52 alloy/Gold ceramic seal. Seal Hole: 0.120 ±0.002 (3.04 ±0.05) Case J6 FMCE-0828, Rev C, 20100419 Please refer to the numerical dimensions for accuracy. All information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. Copyright © 1999-2010 Interpoint Corp. All rights reserved. Figure 12: Case J6 www.craneae.com/interpoint Page 8 of 11 FMCE-0828 Rev J - 2011.09.08 2.150 (54.61) 0.000 0.170 (4.32) 0.210 (5.33) 0.25 (6.4) 0.000 0.405 max (10.29) 0.000 Crane Aerospace & Electronics Power Solutions FMCE-0828 EMI Input Filters – Cases 28 Volt input – 8 Amp TOP VIEW CASE U* Side-leaded case *Designator “SL” required in Case Option position of model number Seam Seal 0.23 (5.8) Pin Length 0.128 dia (3.25). 1.505 (38.23) max. 11 0.850 (21.59) 3 10 0.650 (16.51) 4 9 0.450 (11.43) 5 8 0.250 (6.35) 6 7 0.000 0.120 (3.05) 0.000 Case dimensions in inches (mm) Tolerance ±0.005 (0.13) for three decimal places ±0.01 (0.3) for two decimal places unless otherwise specified CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300°C for 10 seconds per pin. Materials Header Cold Rolled Steel/Nickel/Gold Cover Kovar/Nickel Pins #52 alloy/Gold, compression glass seal Seal Hole: 0.100 ±0.002 (2.54 ±0.05) Case U EMI SL, Rev F, 20100401 Please refer to the numerical dimensions for accuracy. All information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. Copyright © 1999-2010 Interpoint Corp. All rights reserved. Figure 13: Case U www.craneae.com/interpoint Page 9 of 11 FMCE-0828 Rev J - 2011.09.08 0.220 (5.59 2 0.040 dia (1.02) 0.050 (1.27) 0.000 1.050 (26.67) 2.750 (69.85) 12 0.120 (3.05) 0.250 (6.35) 1.250 (31.75) 1 2.880 (73.15) 3.005 (76.33) max. 1.380 (35.05) 0.400 (10.16) max. Angled corner indicates pin one. Crane Aerospace & Electronics Power Solutions FMCE-0828 EMI Input Filters 28 Volt input – 8 Amp stanDarD anD /es (non-Qml) anD /883 (Class h, Qml) mil-PrF-38534 element eValuation ComPonent-leVel test PerFormeD non-Qml Qml stanDarD anD /es Class h /883 m/s 2 m/s 2 P3 Visual Internal Visual Final Electrical Wire Bond Evaluation Element Electrical Notes: 1. Non-QML products may not meet all of the requirements of MIL-PRF-38534. 2. M/S = Active components (Microcircuit and Semiconductor Die) 3. P = Passive components, Class H element evaluation. Not applicable to Standard and /ES element evaluation. scReenIng table 6: eleMent evaluatIOn—hIgh RelIabIlItY standaRd, /es and /883 (class h) Screening Table 1: Element Evaluation www.craneae.com/interpoint Page 10 of 11 FMCE-0828 Rev J - 2011.09.08 Crane Aerospace & Electronics Power Solutions FMCE-0828 EMI Input Filters 28 Volt input – 8 Amp stanDarD anD /es (non-Qml) anD /883 (Class h, Qml) mil-PrF-38534 enVironmental sCreening non-Qml 1 test PerFormeD pre-cap inspection, Method 2017, 2032 stanDarD /es Qml /883 temperature cycle (10 times) Method 1010, Cond. C, -65°C to +150°C, ambient Method 1010, Cond. B, -55°C to +125°C, ambient constant acceleration Method 2001, 3000 g Method 2001, 500 g Burn-in Method 1015, +125°c case, typical 2 96 hours 160 hours Final electrical test, Mil-prF-38534, group a, Subgroups 1 through 6, -55°C, +25°C, +125°C case Subgroups 1 and 4, +25°C case Hermeticity test Gross Leak, Method 1014, Cond. C Fine Leak, Method 1014, Cond. A Gross Leak, Dip Final visual inspection, Method 2009 Test methods are referenced to MIL-STD-883 as determined by MIL-PRF-38534. Notes: 1. Standard and /ES, non-QML products, may not meet all of the requirements of MIL-PRF-38534. 2. Burn-in temperature designed to bring the case temperature to +125°C minimum. Burn-in is a powered test. scReenIng table 7: envIROnMental scReenIng—hIgh RelIabIlItY standaRd, /es and /883 (class h) Screening Table 2: Environmental Screening FMCE-0828 EMI Input Filters, FMCE-0828 Rev J - 2011.09.08. This revision supersedes all previous releases. All technical information is believed to be accurate, but no responsibility is assumed for errors or omissions. Crane Electronics, Inc. reserves the right to make changes in products or specifications without notice. Interpoint and FMCE-0828 are trademarks of Crane Electronics, Inc. Copyright © 1999 - 2011 Crane Electronics, Inc. All rights reserved. www.craneae.com/interpoint Page 11 of 11