Special order options for Leaded Aluminum Electrolytic Capacitors Axial Taping Suffixes Axial taping All Axial lead Tape and Reel Axial taping and reel, Non-standard taping Suffix SD SDC# Radial Taping Suffixes Diameter 4,5,6.3,8,10,12.5 4,5,6.3 8 4 5 16,18 12.5 Taping configuration Ammo pack, 5.0 mm lead spacing Ammo pack, 2.5 mm lead spacing Ammo pack, 3.5 mm lead spacing (straight leads) Ammo pack, 1.5 mm lead spacing (straight leads) Ammo pack, 2.0 mm lead spacing (straight leads) Ammo pack, 7.5 mm lead spacing (straight leads), 15mm feeder hole spacing Ammo pack, 5 mm lead spacing , 15mm feeder hole spacing Suffix SA ST SF ST1 ST2 Cut and formed leads suffixes Diameter 4, 5, 6.3, 8 4, 5, 6.3, 8, 10, 12.5, 16, 18 4, 5, 6.3, 8, 10, 12.5, 16, 18 Description Cut and formed leads Straight leads Snap-in formed leads Optional Sleeving Suffix Polyester (PET) Sleeve Suffix Y Special/Nonstandard tolerance Suffix Suffix K (+/- 10%) Q (-10%, +30%) Optional end sealing Suffix Epoxy end seal Epoxy end seal with PET sleeve PET Sleeve only Suffix PX MX MS Add the suffix to the end of the part number Suffix B CC SI SQ SH Axial Lead Taping Specifications for Aluminum Electrolytic Capacitors TAPING SPECIFICATIONS REFERENCE STANDARDS: EIA RS296E CASE SIZE: Minimum Diameter: 5.0mm Maximum Diameter: 12.5mm PITCH: Standard: 10.2mm Optional: 15.2mm* LEAD TAPING SPECIFICATIONS Inside Tape (W) TAPE LEADER: A 300mm minimum length leader is provided before the first capacitor and after the last capacitor. ORIENTATION FOR POLARITY: All polarized capacitors are oriented in one direction. Anode-white, Cathode-color for polarized capacitors. INTERRUPTION OF SEQUENCE: No consecutive capacitors may be absent. Total empty spaces <0.1% of reel. SPLICES: Spliced tape strength is equal to non-spliced tape. Staples will not be used for splicing. Splice offset < 0.80mm Splice overlap > 50.8mm CASE SIZE vs. PITCH Case Diameter (D) Pitch* (P) Tol. 5.0 6.3 8.0 10.0 12.5 ±0.5 10.0 10.0 10.0 15.0 15.0 ±0.5 52.4 63.5 Tolerance Inside (W) 73.0 ±1.5 Lead Extension (K) 0.80 Max. Centering Tolerance* ±1.40 Lead into Tape 1/2 t Min. Tape Width (t) 5.0 to 6.35 Exposed Adhesive (t0) .80 Max Lead Bend Alignment (F) 1.2 Max. Overall Width (C1) 123.5 Max. STANDARD TAPING SPECIFICATIONS NOMINAL CASE LENGTH: mm TYPICAL PACKAGING QUANTITIES (Reel) Case Diameter (D) Quantity/Reel (Max.) 5.0 6.3 8.0 10.0 12.5 1500 1250 1000 500 400 NOTES: *Maximum body diameter must be less than nominal component pitch Please contact IC directly for all special requirements L1 L L2 Inside Tape (W) ≤ 16.0 ≤ 20.0 ≤ 35.5 52.4 Standard(SD) Optional(C2) Optional(C3) 63.5 Optional(C1) Standard(SD) Standard(SD) 73.0 Optional(C1) Optional(C2) Optional(C3) REEL DIMENSIONS MIN. Outside Diameter (D1) 76.2 355.6 Core Diameter (C) 34.9 92.1 13.9 38.1 Arbor Hole Diameter (A) MAX. 1.5 to 8.0 over C1 Dim Inside Flange (B) D P K + A C F * t B t0 W D1 C1 ® 3757 W. Touhy Ave., Lincolnwood, IL 60712 • (847) 675-1760 • Fax (847) 673-2850 • www.illcap.com 29 ORIENTATION OF POLARITY: All polarized capacitors must be oriented in the same direction. INTERRUPTION OF SEQUENCE: No consecutive capacitors may be absent. Empty spaces <0.1% of reel quantity. SPLICES: Splice tape strength must be equal to Non-splice tape. Splice thickness: <4 single tape layers Splice offset: <0.3 mm REFERENCE STANDARD: EIA RS 468A Formed lead Straight lead Formed lead spacing 4.0 5.0 5.0 6.3 8.0 10.0 12.5 16/18 12.5 Tol. 5.0 1.5/2.5 2.0/2.5 2.5 3.5 5.0 5.0 7.5 7.5 +0.8/-0.2 Taping code SA ST1/ ST ST2/ ST ST SF SA SA SQ SH Capacitor Pitch (P) 12.7 12.7 25.4 15.0 15.0 +1.0 Feed hole pitch (Po) 12.7 12.7 12.7 15.0 15.0 +0.3 Feed hole to first lead (P1) 3.85 Carrier width (W) 18.0 9 Lead spacing (S) Feed hole position (W1) Height of seating plane (H) Lead wire clinch Height (H0) 17.5 Clinch Height(K) 1.5 6.3 18.5 8.0 Straight lead spacing 4.0 Case Diameter (D) 5.1 18.5 20.0 2.5 3.75 +0.7 18 18.0 +0.5 9.0 9.0 +0.5 18.5 16.0 2.5 4.6 4.0 18.5 18.5 16.0 21 MAX ----- ---- +0.5 ----- ---- Nom Feed Hole Diameter (D0) 4.0 4.0 4.0 +0.3 Lead Protrusion (L) 11.2 11.2 11.2 MAX Front to Back inclination ∆h 0.0 0.0 0.0 +2.0 Body inclination ∆h1 0.0 0.0 0.0 +2.0 Tape thickness (t) 0.7 0.7 0.7 +2.0 Box Quantity Box Dimensions (mm) L (MAX) 340 H (MAX) 360 T (MAX) 65 Diameter 4.0 5.0 6.3 8.0 10 12.5 12.5 16 18 Po 12.7 12.7 12.7 12.7 12.7 12.7 15 15 15 Quantity 2000 2000 2000 1000 800 400 500 300 243 Aluminum Electrolytic Capacitors STANDARD RADIAL LEAD CUT & FORM SPECIFICATION Special Order Options* Add code to end of part number Dimensions Code Description Dimension Figure Standard Cut and Formed Leads B D F P L 4.0 5.0 1.5 4.5 5.0 5.0 2.0 4.5 6.3 5.0 2.5 4.5 4.5± 1.0 0.5 *2.5 max for case length > 7mm * P±0.5 D F±0.5 1.5 max for case length ≤ 7mm d 8.0 5.0 3.5 4.5 L Dimensions Standard Straight Cut Leads CC D F L 4.0 1.5 5.0 5.0 2.0 5.0 6.3 2.5 5.0 8.0 3.5 5.0 L±0.5 D F±0.5 d 10.0 5.0 5.0 12.5 5.0 5.0 16.0 7.5 5.0 18.0 7.5 5.0 H Dimensions l Formed Snap-in Cut Leads SI D F P l H 4.0 5.0 1.5 0.85 2.6 5.0 5.0 2.0 0.85 2.8 6.3 5.0 2.5 0.85 2.8 8.0 5.0 3.5 1.0 2.7 1.0 MAX D * *2.5 max for case length > 7mm 4.5± 1.0 0.5 1.5 max for case length ≤ 7mm H P±0.5 F±0.5 d H Dimensions l Straight-Cut Snap-in Cut Leads SI P I H 5.0 4.5 2.7 12.5 5.0 4.5 2.7 16.0 7.5 4.5 2.7 D F 10.0 18.0 *for non-standard requirement contact I.C. 7.5 4.5 2.7 1.0 MAX D L±0.5 D F±0.5 d Convert to inches, divide by 25.4 ® 3757 W. Touhy Ave., Lincolnwood, IL 60712 • (847) 675-1760 • Fax (847) 673-2850 • www.illcap.com 31