Analog Accelerometers Product Catalog Copyright © 2010 Measurement Specialties, Inc. All Rights Reserved Analog Accelerometers Catalog precisionsensors.meas-spec.com 2236 N. Cleveland-Massillon Road Akron OH 44333 PH : 330-659-3312 8/21/2013 www.meas-spec.com Analog Accelerometers Ordering Guide Ordering an Analog Accelerometer When ordering an analog accelerometer, the range and bandwidth options must be specified and accessories ordered separately. 1) First, select the base accelerometer: Number of Axes ±1 g to ±2 g ±1 g to ±15 g ±5 g to ±50 g ±10 g to ±70 g ±5 g to ±100 g ±250 g to ±500 g Triaxial 34201A XL403A 34205A 34200B 34207A* 34206A 34208A Biaxial 23201A XL403A 23200C 23207A* 23208A Uniaxial 13201A XL403A 13203CC 13200C 13207A* 13208A *Call for availability 2) Then specify parameters and options for the accelerometer: Part # Description -Rnnn ±nnn g range† -Bnnn ±nnn Hz bandwidth 3dB cutoff† -T004 4 foot cable with D-subminiature connector -Tnnn Custom length cable with D-subminiature connector -T000 Terminal block on uni- and biaxial models only -T000 Berg Conan connector for PCB mount, triaxial models -C002 Room temperature calibration plus offset compensation over -40 to +85°C (uni- and biaxial models only) 35172A Vertical mounting adapter for non-cubical models only 35173A Horizontal mounting adapter for non-cubical models only 34170B Compact mounting adapter for triaxial models only 99100 Return to Measurement Specialties for NIST calibration (C001 cal) 99200 Return to Measurement Specialties for NIST & temperature calibration (C002 cal) †select nnn from Ordering Information on data sheets Please contact us for availability of custom ranges, bandwidths, and termination cable length. Notes Required Required Default Optional Optional Optional Optional Optional Optional Optional Optional Optional XL403A ±1 g to ±15 g Rugged Uniaxial, Biaxial, or Triaxial Accelerometer for Quick Shipment Technical Data* Features and Benefits High Accuracy and Linearity over Wide Temperature Range The voltage output for the XL403A is directly proportional to the acceleration along the axis. Each DC-coupled output is fully scaled, referenced, and temperature compensated. Accuracy is improved by minimizing variations due to temperature and aging effects, resulting in sensors that are more stable over temperature than piezoelectric or piezoresistive devices. Calibration Certificate Each XL403A is supplied with a calibration certificate listing sensitivity and offset, as well as the on-axis and transverse alignment parameters needed to ensure rapid and efficient system implementation. The alignment data can be used to compensate the measured values if needed. Self-Test on Digital Command A TTL-compatible self-test input causes a simulated acceleration to be injected into the accelerometer to verify channel integrity. Small Size Complete conditioned uniaxial, biaxial, or triaxial accelerometer in less than a cubic inch. uilt-In Power Supply Regulation B Unregulated DC power from +8.5 to +36 Volts is all that is required to measure acceleration and temperature. Reverse power voltages of up to -80 V can be withstood indefinitely. Transients of +80 V for 550 ms compatible with MIL-STD-704A can be withstood with full operation. Easy Installation Integrated cable with 9-pin connector makes it easy to wire. Two throughholes and four tapped holes simplify mounting. uitable for Harsh Environments S The XL403A is robust and can be used in harsh environments. The unit will survive 5000 g powered or unpowered. Earth Friendly Design Lead-free design makes the XL403A environmentally safe while Measurement Specialties’ assembly process ensures reliable functionality. Fully potted electronics eliminates the possibility of tin whiskers-related failures. Warranty These Measurement Specialties accelerometers come with a three-year factory warranty. XL403A Analog Accelerometer precisionsensors.meas-spec.com 2236 N. Cleveland-Massillon Road Akron OH 44333 PH : 330-659-3312 Get Started on Simplified Acceleration and Temperature Measurements The Measurement Specialties XL403A is ready when you are. In stock and ready to ship, you can be taking measurements in less time than with built-to-order accelerometers. The small size and built-in power regulation allow the XL403A to fit where other accelerometers can’t. Choose bandwidth up to 800 Hz and range options of ±1 g to ±15 g to measure accelerations on one, two or three axes. Tested over the -40 to +85°C temperature range, the accelerometers have a nominal full scale output swing of ±2 Volts. The zero g output level is nominally +2.5 Volts. Precise values are available on the included calibration certificate. 7/19/2013 www.meas-spec.com Specifications - improved specifications available upon request Ta = Tmin to Tmax; 8.5 ≤ Vs ≤ 36 V; Acceleration = 0 g unless otherwise noted; within one year of calibration. Parameter Min Typical Max Units Range Measurement Full Scale ±1 ±15 g Sensitivity At 25°C, Option R005 Drift Tmin to Tmax 400† ±0.65 ±3 mV/g % Zero g Bias Level At 25°C Drift Tmin to Tmax 2.5 20 Alignment Deviation from Ideal Axes ±1.0 Transverse Sensitivity ±0.25 Nonlinearity 0.1 Frequency Response, 5-pole 0 Noise Density Self-Test Pull-up Resistor 5 Temperature Sensor Sensitivity 0°C Bias Level Outputs Output Voltage Swing Capacitive Drive Capability 0.05 1000 Power Supply (Vs) Input Voltage Limits Input Voltage - Operating Input Current Rejection Ratio Conditions/Notes On each axis. Must specify via Option Rnnn Precise values on cal certificate Percent of sensitivity at 25°C V mg ±3.0 Precise values on cal certificate At 1.25°C/min. temperature rate of change Precise values on cal certificate Can be compensated if required degrees % 0.5 % FSR 800 Hz 100 Inherent sensor error, excluding misalignment Best fit straight line Upper cutoff per Option Bnnn, -3dB pt ±10%, 5-pole Butterworth filter µg/√Hz 10 Hz to 400 Hz kΩ 6.45 509 Logic "1"≥ 3.5 V, Logic "0"≤ 1.5 V, "0" causes self-test Accuracy ±1°C mV/°C mV 4.95 V pF Iout = ±0.5 mA -80 +8.5 12 >120 +80 +36 V V mA dB -80 V continuous, >38 V if ≤550 ms, duty <1% Continuous Temperature Range (Ta) -40 +85 °C Mass Shock Survival -5000 †Scale 38 DC grams +5000 Precise values on cal certificate g Any axis for 0.5 ms, powered or unpowered linearly with range option Rnnn; see Ordering Information Mechanical Connections T004 Male D-Shell Connector 3 3 Pin 1 2 3 4 5 6 7 Signal Analog1+Analog2+Analog3+ Signal - Reserved Reserved Self Test Wire Brown Red Orange Yellow Green Blue Violet 8 +Vs Grey 9 Gnd White Ordering Information XL403A Two through holes and four 3 mm x 0.5 mm threaded holes are provided for mounting. - X1 - R006 - B500 Instrument XL403A T004D Connector A : None, tinned leads D : 9-pin DB9M connector Axes X1 : Uniaxial X2 : Biaxial X3 : Triaxial Range Rnnn : Choose 001 (±1 g) through 015 (±15 g) Mounting adapters (sold separately) - Termination Length T004 : 4 ft. cable Tnnn : Custom length, nnn ft. (custom cable adds to lead time) Bandwidth Bnnn : Choose 001 (0 to 1 Hz) through 800 (0 to 800 Hz) 35173A Horizontal XL403A Analog Accelerometer precisionsensors.meas-spec.com 35172A Vertical 2236 N. Cleveland-Massillon Road Akron OH 44333 PH : 330-659-3312 7/19/2013 www.meas-spec.com 34201A ±1 g to ±2 g Triaxial Accelerometer Zero g Bias Stability ±2 mg Very Low Noise 110 µg/√Hz Technical Data* Features and Benefits Precision The Measurement Specialties 34201A Triaxial Accelerometer offers precision measurements over the entire -40 to +85°C temperature range with superior bias stability and approximately 100 µg measurement resolution. High Accuracy and Linearity over Wide Temperature Range The voltage output for each axis of the 34201A is directly proportional to the acceleration along that axis. Each DC-coupled output is fully scaled, referenced and temperature compensated over the entire -40 to +85°C temperature range. Our internal temperature compensation routine provides for unrivaled measurement accuracy over varying temperatures. Calibration Certificate Each 34201A is supplied with a calibration certificate listing sensitivity and offset, as well as the on-axis and transverse alignment parameters needed to ensure rapid and efficient system implementation. Self-Test on Digital Command A TTL-compatible self-test input causes a simulated acceleration to be injected into all three sensors to verify channel integrity. Small Size Complete conditioned triaxial accelerometer in less than one cubic inch. uilt-In Power Supply Regulation B Unregulated DC power from +8.5 to +36 volts is all that is required to measure accelerations on all axes. Suitable for Harsh Environments The 34201A is robust and can be used in harsh environments. The unit will survive 3500 g powered and unpowered. Warranty These Measurement Specialties accelerometers come with a three-year factory warranty. 34201A Triaxial Analog Accelerometer precisionsensors.meas-spec.com Precisely Measure Real -World Accelerations The Measurement Specialties 34201A accelerometer has each mutually orthogonal axis precisely aligned, typically within ±0.15 degree of the theoretical ideal. This provides the accuracy required by most measurement applications without any compensation. Critical applications requiring higher accuracy can use the alignment data provided on the optional calibration certificate to compensate for any small residual error. Choose the bandwidth and range options best suited for your application to measure ±1 g, ±1.5 g, or ±2 g accelerations on each of three axes. Each axial sensor has been tested over the -40 to +85°C temperature range and has has a nominal full scale output swing of ±2 volts. The zero g output level is nominally +2.5 volts and temperature compensated over the range of -40 to +85°C. Precise values for each axis are available on the included calibration certificate. 2236 N. Cleveland-Massillon Road Akron OH 44333 PH : 330-659-3312 7/18/2013 www.meas-spec.com Specifications for 34201A - improved specifications available upon request Ta = Tmin to Tmax; 8.5 ≤ Vs ≤ 36 V; Acceleration = 0 g unless otherwise noted; within one year of calibration. Parameter Min Typical Max Units Range Measurement Full Scale ±2.0 g Sensitivity At 25°C, Option R002 Drift Tmin to Tmax 1000† ±0.3 mV/g % Zero g Bias Level At 25°C Drift Tmin to Tmax 2.5 ±2 Alignment Deviation from Ideal Axes ±0.15 Transverse Sensitivity 0.25 Nonlinearity ±0.2 Frequency Response Noise Density Self Test Pull-up Resistor Temperature Sensor Sensitivity +0°C Bias Level Outputs Output Voltage Swing, R001, R1.5 Output Voltage Swing, R002 0.05 0.55 4.95 4.8 V V Power Supply (Vs) Input Voltage Limits Input Voltage - Operating Input Current Rejection Ratio -20 +8.5 13 >120 +36 +36 V V mA dB Temperature Range (Ta) -40 +85 °C Mass Shock Survival -3500 †Scale 0 On each axis. Must specify via Option Rnnn Precise values on cal certificate ±6 V mg ±0.5 degrees ±1.25 % FSR Precise values on cal certificate At <1.25°C/min temperature rate of change % 2100 110 Precise values on cal certificate Can be compensated if required Inherent sensor error, excluding misalignment Hz Upper cutoff per Option Bnnn, -3 dB pt ±10% µg/√Hz 5 kΩ 6.45 509 mV/°C mV 35 grams +3500 g Logic "1" ≥ 3.5 V, "0" ≤ 1.5 V; "0" causes self-test Error ±1°C over temperature Series 100 Ω for capacitance tolerance >1 MΩ load >1 MΩ load; limits typically reach 0.2 V to 4.95 V -20 V continuous, >30 V if <100 ms, duty <1% No load, quiescent DC Precise values on cal certificate Any axis for 0.5 ms, powered or unpowered linearly with range option Rnnn; see Ordering Information Mechanical 2 Conditions/Notes 3 3 1 2 3 1 1 Connections T004 2 1.115 [28,30] Pin 1 2 3 4 5 Signal A1+ Signal- A2+ +5V Out A3+ Wire Brown Red Orange Yellow Green 0.295 [7,50] 3 mm x 0,5 mm Thread 3,5 mm [0.138] Deep 0.295 [7,50] (6) Mounting Holes on 3 sides 0.945 0.354 Two 3 mm [24,00] [9,0] x 0.5 mm threaded holes are provided on each of three orthogonal faces for mounting. 34201A Triaxial Analog Accelerometer precisionsensors.meas-spec.com 0.945 [24,00] 0.354 [9,0] Dimensions in inches [mm], identical for each view where applicable. Termination T004 : 4 ft. cable with DB9M T000 : PCB mount (Not shown, call SI) Tnnn : Custom length, nnn ft. (call SI) 1 2 Shown with 34170B mounting adapter (sold separately) 9 Gnd White Ordering Information Cable to 9-pin male D-Shell connector 3 6 7 8 T+ Self Test-L +Vs Blue Violet Grey Instrument Bandwidth B2k1 : 0 to 2100 Hz B1k4 : 0 to 1400 Hz B944 : 0 to 944 Hz B380 : 0 to 380 Hz B208 : 0 to 208 Hz B142 : 0 to 142 Hz B094 : 0 to 94 Hz B066 : 0 to 66 Hz B031 : 0 to 31 Hz B6.6 : 0 to 6.6 Hz Range R002 : ±2 g R1 . 5 : ±1.5 g R001 : ±1 g 2236 N. Cleveland-Massillon Road Akron OH 44333 PH : 330-659-3312 7/18/2013 www.meas-spec.com 13201A Uniaxial ±1 g to ±2 g Accelerometers Zero g Bias Stability ±2 mg Very Low Noise 110 µg/√Hz 23201A Biaxial C 1A 1 3 2 08 Technical Data* Features and Benefits Precision These Measurement Specialties accelerometers offer precision measurements over the entire -40 to +85°C temperature range with superior bias stability and approximately 100 µg measurement resolution. High Accuracy and Linearity over Wide Temperature Range The voltage output for the 13201A and 23201A is directly proportional to the acceleration along the axis. The DC-coupled output is fully scaled, referenced and temperature compensated over the entire -40 to +85°C temperature range. Optional internal temperature compensation provides unrivaled measurement accuracy over varying temperatures. Calibration Certificate Each 13201A and 23201A is supplied with a calibration certificate listing sensitivity and offset, as well as the on-axis and transverse alignment parameters needed to ensure rapid and efficient system implementation. Increased offset compensation can be obtained with Option C002. Self-Test on Digital Command A TTL-compatible self-test input causes a simulated acceleration to be injected into all three sensors to verify channel integrity. Small Size Complete accelerometer in approximately one cubic inch volume. uilt-In Power Supply Regulation B Unregulated DC power from +8.5 to +36 Volts is all that is required to measure acceleration and temperature. Reverse power voltages of up to -80 V can be withstood indefinitely. Transients of +80 V for 550 ms compatible with MIL-STD-704A can be withstood with full operation. Easy Installation A built-in terminal block or cable with 9-pin connector simplifies wiring. Tapped holes on bottom and back simplify horizontal or vertical mounting. Suitable for Harsh Environments These accelerometers are robust and can be used in harsh environments. The unit will survive 3500 g powered and unpowered. Simplify Acceleration Measurements Measurement Specialties 13201A and 23201A accelerometers have either one or two orthogonal axes and a temperature sensor in a small, rugged package. The small size and built-in power regulation allow them to fit in most applications without any external circuitry or conditioning. Choose the bandwidth and range options best suited for your application to measure ±1 g, ±1.5 g, or ±2 g accelerations on one or two axes. Each axial sensor has been tested over the -40 to +85°C temperature range. Each axis has a nominal full scale output swing of ±2 Volts from the zero-g output level of nominally +2.5 Volts. Precise values for each axis are provided on the calibration certificate included with each sensor. Warranty These Measurement Specialties accelerometers come with a three-year factory warranty. 13201A.23201A Analog Accelerometer precisionsensors.meas-spec.com 2236 N. Cleveland-Massillon Road Akron OH 44333 PH : 330-659-3312 8/2/2013 www.meas-spec.com Specifications for 13201A and 23201A - improved specifications available upon request Ta = Tmin to Tmax; 8.5 ≤ Vs ≤ 36 V; Acceleration = 0 g unless otherwise noted; within one year of calibration. Parameter Min Typical Max Units Range Measurement Full Scale ±2.0 g Sensitivity At 25°C, Option R002 Drift Tmin to Tmax 1000† ±0.3 mV/g % Zero g Bias Level At 25°C Drift Tmin to Tmax, Option C001 Drift Tmin to Tmax, Option C002 2.500 ±20 ±2 ±60 ±6 V mg mg Alignment Deviation from Ideal Axes ±.75 ±3 degrees Transverse Sensitivity 0.25 Nonlinearity ±0.2 ±1.25 % FSR Frequency Response Noise Density Self Test Pull-Up Resistor Temperature Sensor Sensitivity +0°C Bias Level Outputs Output Voltage Swing, R001, R1.5 Output Voltage Swing, R002 0.05 0.55 4.95 4.8 V V Power Supply (Vs) Input Voltage Limits Input Voltage - Operating Input Current Rejection Ratio -80 +8.5 10 >120 +80 +36 V V mA dB Temperature Range (Ta) -40 +85 °C Mass Shock Survival -3500 †Scale 0 % 2100 110 Hz Conditions/Notes On each axis. Must specify via Option Rnnn Precise values on cal certificate Typ ±2 mV; Precise values on cal certificate At <1.25°C/min temperature rate of change At <1.25°C/min temperature rate of change Precise values on cal certificate Can be compensated if required Inherent sensor error, excluding misalignment Upper cutoff per Option Bnnn, -3 dB pt ±10% µg/√Hz 5 kΩ 6.45 509 mV/°C mV 38 grams +3500 g Logic "1" ≥ 3.5 V, "0" ≤ 1.5 V; "0" causes self-test Error ±1°C over temperature Series 100 Ω for capacitance tolerance >1 MΩ load >1 MΩ load; limits typically reach 0.2 V to 4.95 V -80 V continuous, >38 V if ≤550 ms, duty <1% No load, quiescent DC Excludes cable; T000 values on cal certificate Any axis for 0.5 ms. Powered or unpowered linearly with range option Rnnn; see Ordering Information Mechanical Connections T000 T004 Pin 1 2 3 4 5 Signal A2+ Signal- T+ +5V Out A1+ Wire Brown Red Orange Yellow Green 6 7 8 Signal-Self Test-L +Vs Blue Violet Grey 9 Gnd White Ordering Information Two through holes and four 3 mm x 0.5 mm threaded holes are provided for mounting. Instrument Calibration 23201A 13201A Bandwidth Range Mounting adapters (sold separately) 35173A Horizontal 13201A.23201A Analog Accelerometer precisionsensors.meas-spec.com Termination 35172A Vertical 2236 N. Cleveland-Massillon Road Akron OH 44333 PH : 330-659-3312 8/2/2013 www.meas-spec.com 13203CC TM Eliminates management of calibration data Interchangeable, Rugged Uniaxial Accelerometer ±1 g to ±15 g Preliminary Technical Data* Features and Benefits IdentiCal™ Interchangeable Sensor IdentiCal™ sensors eliminate the management of calibration data and allow convenient interchangeability of individual sensors. With standardized sensitivity and offset, there is no need to enter new parameters for each unit. 13203CC is perfect for high volume use. TM Rugged for Harsh Environments The 13203CC is robust to perform well in harsh environments. The 6061-T6 case with electroless nickel finish plus a Teflon cable with a shield bonded to the case provide improved resistance to EMI, lightning, or other disturbances. The enclosure is rated IP65. The unit has resilient power and will survive 5000 g powered and unpowered. The 13203CC has a 22 AWG cable with only four wires to connect. High Accuracy and Linearity over Wide Temperature Range The output of the 13203CC is directly proportional to the acceleration of its axis. The DC-coupled output is fully scaled, referenced, and temperature compensated. When used in demanding temperature environments, the 13203CC is one of the most accurate accelerometers available. Small Size Complete conditioned accelerometer package in less than a cubic inch; it may be easily mounted for any axis orientation. uilt-In Power Supply Regulation B Unregulated DC power from +8.5 to +36 Volts is all that is required to measure acceleration. The 13203CC is operational with transients of +80 V for 550 ms compatible with MIL-STD-704A. Earth Friendly Design Lead-free design makes the 13203CC environmentally safe while Measurement Specialties’ assembly process ensures reliable functionality. Fully potted electronics eliminates the possibility of tin whiskers-related failures. Three Year Warranty These Measurement Specialties’ accelerometers are covered by a three year return to factory warranty. Extended warranties are available. 13203CC Uniaxial Analog Accelerometer precisionsensors.meas-spec.com Precisely Measure Rates Over Temperature The Measurement Specialties 13203CC is an interchangeable and rugged uniaxial accelerometer capable of accurately measuring acceleration under demanding environmental conditions. A tough, compact housing holds potted electronics and a shielded heavyweight cable. Its cubical form allows mounting with the sensing axis oriented in any direction. The 13203CC provides enhanced accuracy and durability features to meet the challenges of your application. In addition to its robust construction, increased precision is achieved through improved offset and gain compensation. Each axial sensor has been tested over the -40 to +85°C temperature range and has a nominal full scale output swing of ±2 Volts. Sensors are available in various fixed sensitivities, each with a 2.500 V offset. The 13203CC can also be ordered with different bandwidths and wiring configurations. 2236 N. Cleveland-Massillon Road Akron OH 44333 PH : 330-659-3312 7/18/2013 www.meas-spec.com Specifications for 13203CC - improved specifications available upon request Ta = Tmin to Tmax; 8.5 ≤ Vs ≤ 36 V; Acceleration = 0 g unless otherwise noted; within one year of calibration. Parameter Range & Sensitivity* at 25°C Option R015 Option R010 Option R006 Option R005 Option R004 Option R003 Option R002 Option R001 Min Typical Max Units 0.130 0.200 0.330 0.400 0.500 0.660 1.000 2.000 V/g V/g V/g V/g V/g V/g V/g V/g % FSR Sensitivity Drift 25°C to Tmin or Tmax ±1.0 Offset at 25°C Zero g Bias Level 2.500 V Offset Drift 25°C to Tmin or Tmax ±1.0 % FSR Alignment Deviation from Ideal Axes ±1.5 degrees Transverse Sensitivity 0.25 % Nonlinearity 0.065 Frequency Response 0 Noise Density Outputs Output Voltage Swing Power Supply (Vs) Input Voltage Limits Input Voltage - Operating Input Current Rejection Ratio -80 +8.5 12 >120 +80 +36 Temperature Range (Ta) +85 Mass Shock Survival Conditions/Notes Must specify via Option Rnnn, see Ordering Info Maximum error ±0.75% of nominal at 25°C. Max error ±50 mg of nominal at 25°C Inherent sensor error, excluding misalignment % FSR 800 Best fit straight line Hz 100 Upper cutoff per Option Bnnn, -3dB pt ±10% µg/√Hz 0.25 4.75 -40 Ta = 25°C Measuring equipment >10 MΩ recommended Iout = 1 mA, Capacitive load <1000 pF V V V mA dB -80V continuous, >38 V if ≤550 ms, duty <1% No load, quiescent DC °C 38 grams -5000 +5000 g Any axis for 0.5 ms, powered or unpowered Data subject to change without notice *IdentiCal sensors are interchangeable, any with same range have same value Mechanical 1 1 1 Option D Male D-Shell Connector 1.073 [27,30] 0.295 [7,50] 3 mm x 0,5 mm Thread 3,5 mm [0.138] Deep 0.295 [7,50] (6) Mounting Holes on 3 sides Pin Signal Wire 0.945 [24,00] 0.354 [9,0] Dimensions in inches [mm], identical for each view where applicable. 22 AWG Cable 1 6061-T6 aluminum case with electroless nickel finish plus integrated cable with shield bonded at the case Shown with 34170B mounting adapter (sold separately) 13203CC Uniaxial Analog Accelerometer precisionsensors.meas-spec.com 1 A1+ Green 2 Signal - Blue 3 Not Used 4 Not Used 5 Not Used 6 Not Used 7 Not Used 8 +Vs Orange 9 Gnd White Ordering Information 13203CC - R015 - B800 - T2.5B 0.945 0.354 [24,00] [9,0] Third angle Connections Instrument 13203CC Range R015 : R010 : R006 : R005 : R004 : R003 : R002 : R001 : ±15 g ±10 g ±6 g ±5 g ±4 g ±3 g ±2 g ±1 g Bandwidth B800 : 0 to B380 : 0 to B208 : 0 to B142 : 0 to B094 : 0 to B066 : 0 to B031 : 0 to B6.6 : 0 to Connector A : None, tinned leads B : None, DIN 46228 terminal tubes C : 6-pin M12 connector D : 9-pin DB9M connector 800 Hz 380 Hz 208 Hz 142 Hz 94 Hz 66 Hz 31 Hz 6.6 Hz 2236 N. Cleveland-Massillon Road Akron OH 44333 PH : 330-659-3312 Termination Length T2.5 : 2.5 ft. cable T004 : 4 ft. cable Tnnn : Custom length, nnn ft. (call SI) 7/18/2013 www.meas-spec.com PRELIMINARY 34205A ±5 g to ±50 g Triaxial Accelerometer Superior Zero g Bias Stability Low Noise - Wide Bandwidth 5 8 Technical Data* Features and Benefits High Accuracy and Linearity over Wide Temperature Range The voltage output for each axis of the 34205A is directly proportional to the acceleration along that axis. Each DC-coupled output is fully scaled, referenced, and temperature compensated over the entire -40 to +85°C temperature range. CalibrationCertificate Each 34205A is supplied with a calibration certificate listing sensitivity and offset, as well as the on-axis and transverse alignment parameters needed to ensure rapid and efficient system implementation. The alignment data can be used to compensate the measured values to achieve an even higher level of sensor accuracy. Small Size Complete conditioned triaxial accelerometer in less than a cubic inch. uilt-In Power Supply Regulation B Unregulated DC power from +8 to +18 volts is all that is required to measure accelerations on all axes. Suitable for Harsh Environments The 34205A is robust and can be used in harsh environments. The unit is packaged in a rugged aluminum housing and will survive 5000 g powered or unpowered. Warranty These Measurement Specialties accelerometers come with a three-year factory warranty. 34205A Triaxial Analog Accelerometer precisionsensors.meas-spec.com Precisely Measure Real-World Accelerations Measurement Specialties 34205A accelerometer provides the accuracy required by most measurement applications without any compensation. Critical applications requiring higher accuracy can use the alignment data provided on the calibration certificate to compensate for any small residual error. Choose the bandwidth and range options best suited for your application to measure ±5 g, ±10 g, ±20 g, ±25 g, ±30 g, ±40 g, or ±50 g accelerations on each of three axes. Each axial sensor has been tested over the -40 to +85°C temperature range and has a nominal full scale output swing of ±2.25 volts. The zero g output level is nominally +2.5 volts. Precise values for each axis are available on the included calibration certificate. 2236 N. Cleveland-Massillon Road Akron OH 44333 PH : 330-659-3312 8/5/2013 www.meas-spec.com PRELIMINARY Specifications for 34205A - improved specifications available upon request Ta = Tmin to Tmax; 8 ≤ Vs ≤ 18 V; Acceleration = 0 g unless otherwise noted; within one year of calibration. Max Units Range Measurement Full Scale Parameter ±5 ±50 g On each axis. Must specify via Option Rnnn Sensitivity At 25°C, Option R050 Drift Tmin to Tmax 40† ±2.0 mV/g % Nom ±50 g. Precise values on cal certificate Percent of sensitivity at 25°C Zero g Bias Level At 25°C Drift Tmin to Tmax: Option R050, R040, R030, R025, R020 Option R010, R005 Min Typical Conditions/Notes 2.5 ±80 ±16 Alignment Deviation from Ideal Axes ±0.35 Nonlinearity 0.15 Frequency Response Noise Density Option R050, R040, R030, R025, R020 Option R010, R005 50 10 μg/√Hz μg/√Hz Temperature Sensor Sensitivity 0°C Bias Level 6.45 509 mV/°C mV Outputs Output Voltage Swing Capacitive Drive Capability 0.25 500 4.75 V pF Iout = ±0.5 mA Power Supply (Vs) Input Voltage - Operating Input Current Rejection Ratio +8 33 >120 +18 50 V mA dB Will withstand -20 V continuous or 36 V for <1 sec. No load, quiescent DC Temperature Range (Ta) -40 +85 °C Mass Shock Survival -5000 †Scale 0 V Precise values on cal certificate ±200 ±40 mg mg At <1.25°C/min temperature rate of change At <1.25°C/min temperature rate of change ±3.0 degrees Precise values on cal certificate Can be compensated if required 0.5 % FSR Best fit straight line 2000 Hz 35 Upper Cutoff per Option Bnnn, -3 dB pt ±10% grams +5000 g Ta =25°C Accuracy ±1°C typical Precise values on cal certificate Any axis for 0.1 ms, powered or unpowered linearly with range option Rnnn; see Ordering Information Mechanical Connections T004 Pin Signal Wire 1 A1+ Brown 2 3 4 5 Signal- A2+ +5VOut A3+ Red Orange Yellow Green 6 T+ Blue 7 N.C. Violet 8 +Vs Grey 9 Gnd White Ordering Information 34205A Two 3 mm x 0.5 mm threaded holes are provided on each of three orthogonal faces for mounting. 34205A Triaxial Analog Accelerometer precisionsensors.meas-spec.com - R050 - B2k0 - T004 Instrument 34205A Shown with 34170B mounting adapter (sold separately) Range Bandwidth R050 : ±50 g B2k0 : 0 to 2000 Hz R040 : ±40 g B1k4 : 0 to 1400 Hz R030 : ±30 g B944 : 0 to 944 Hz R025 : ±25 g B380 : 0 to 380 Hz R020 : ±20 g B208 : 0 to 208 Hz R010 : ±10 g B1k0 : 0 to 1000 Hz B944 : 0 to 944 Hz R005 : ±5 g B380 : 0 to 380 Hz B208 : 0 to 208 Hz 2236 N. Cleveland-Massillon Road Akron OH 44333 PH : 330-659-3312 Termination T004 : 4 ft. cable with DB9M T000 : PCB Mount (Not shown, Call SI) Tnnn : Custom length, nnn ft. (Call SI) 8/5/2013 www.meas-spec.com PRELIMINARY 34207A Triaxial Accelerometer ±10 g to ±70 g Wide Bandwidth to 10 kHz Precision Aligned Technical Data* Features and Benefits Precision Alignment Each axis of the Measurement Specialties 34207A is precision aligned to minimize errors due to axis misalignment or transverse sensitivity. High Accuracy and Linearity over Wide Temperature Range The voltage output for each axis of the 34207A is directly proportional to the acceleration along that axis. Each DC-coupled output is fully scaled, referenced, and temperature compensated over the entire -40 to +85°C temperature range. Accuracy is improved by minimizing variations due to temperature and aging effects, resulting in a sensor that is more stable over temperature than piezoelectric or piezoresistive devices. Calibration Certificate Each 34207A is supplied with a calibration certificate listing sensitivity and offset, as well as on-axis and transverse alignment parameters needed to ensure rapid and efficient system implementation. The alignment data can be used to compensate the measured values to achieve an even higher level of sensor accuracy. Self-Test on Digital Command A TTL-compatible self-test low input causes a simulated acceleration to be injected into all three sensors to verify channel integrity. Small Size Complete conditioned triaxial accelerometer in less than a cubic inch. uilt-In Power Supply Regulation B Unregulated DC power from +8.5 to +36 volts is all that is required to measure acceleration and temperature. Suitable for Harsh Environments The 34207A is robust and can be used in harsh environments. The unit will survive 4000 g powered or unpowered. Warranty These Measurement Specialties accelerometers come with a three-year factory warranty. 34207A Triaxial Analog Accelerometers precisionsensors.meas-spec.com Precisely Measure Real -World Accelerations The Measurement Specialties 34207A accelerometer has each mutually orthogonal axis precisely aligned within 0.75 degree of the theoretical ideal. This provides the accuracy required by most measurement applications without any compensation. Critical applications requiring higher accuracy can use the alignment data provided on the calibration certificate to compensate for any small residual error. Choose the bandwidth and range options best suited for your application to measure up to ±70 g accelerations on each of three axes. Each axial sensor has been tested over the -40 to +85°C temperature range and has a nominal full scale output swing of ±2 volts. The zero g output level is nominally +2.5 volts. Precise values for each axis are available on the included calibration certificate. 2236 N. Cleveland-Massillon Road Akron OH 44333 PH : 330-659-3312 8/12/2013 www.meas-spec.com PRELIMINARY Specifications for 34207A - improved specifications available upon request Ta = Tmin to Tmax; 8.5 ≤ Vs ≤ 36 V; Acceleration = 0 g unless otherwise noted; within one year of calibration. Parameter Min ±10 Sensitivity At 25°C, Option R070 Drift Tmin to Tmax Units ±70 g Conditions/Notes On each axis, specify with Option Rnnn mV/g % 2.5 ±500 Percent of sensitivity at 25°C V mg Precise values on cal certificate Some units to >750 mg degree Precise values on cal certificate Can be compensated if required Alignment Deviation from Ideal Axes Transverse Sensitivity ±0.25 Nonlinearity 0.2 Frequency Response Noise Density Self-Test Input Impedance 10 Temperature Sensor Sensitivity 0°C Bias Level Outputs Output Voltage Swing Capacitive Drive Capability 0.25 1000 4.75 V pF Iout = ±0.5 mA Power Supply (Vs) Input Voltage Limits Input Voltage - Operating Input Current Rejection Ratio -20 +8.5 15 >120 +38 +36 20 V V mA dB -20V continuous Temperature Range (Ta) -40 +85 °C Mass Shock Survival -4000 †Scale 2 ±0.75 0 % Inherent sensor error, excluding misalignment 2 % FSR 10 kHz 2.2 Best fit straight line Upper cutoff per Option Bnnn, -3 dB pt ±10% mg/√Hz kΩ 6.45 509 Accuracy ±1°C No load, quiescent DC grams +4000 10 Hz to 400 Hz Pullup. Logic "1"≥3.5V, Logic "0"≤1.5V mV/°C mV 35 Precise values on cal certificate g Any axis for 0.5ms, powered or unpowered linearly with range option Rnnn. Mechanical 3 3 1 2 0.295 [7,50] 3 mm x 0,5 mm Thread 3,5 mm [0.138] Deep 0.295 [7,50] (6) Mounting Holes on 3 sides 0.945 0.354 Two 3 mm [24,00] [9,0] x 0.5 mm threaded holes are provided on each of three orthogonal faces for mounting. 34207A Triaxial Analog Accelerometers precisionsensors.meas-spec.com Connections 3 1 1 T004 2 1.115 [28,30] Max ±24† 1% (TBD) Zero g Bias Level At 25°C Drift Tmin to Tmax At 1.25°C/min rate of change Typical Accelerometers Full Scale Range Pin Signal Wire 0.945 [24,00] 0.354 [9,0] Dimensions in inches [mm], identical for each view where applicable. 1 A1+ Brown 2 Signal- Red 3 4 5 A2+ +5VOut A3+ Orange Yellow Green 6 7 8 T+ Self Test-L +Vs Blue Violet Grey 9 Gnd White Ordering Information 34207A - R070 - B1k0 - T004 Termination T004 : 4 ft. cable with DB9M T000 : PCB mount (not shown, call SI) Tnnn : Custom length, nnn ft. (call SI) Cable to 9-pin male D-Shell connector 3 Bandwidth B10k : 0 to 10 kHz B5k0 : 0 to 5 kHz B1k0 : 0 to 1 kHz 1 2 Shown with 34170B mounting adapter (sold separately) Instrument Range R070 : ±70 g R060 : ±60 g R050 : ±50 g R040 : ±40 g R030 : ±30 g R020 : ±20 g R010 : ±10 g 2236 N. Cleveland-Massillon Road Akron OH 44333 PH : 330-659-3312 8/12/2013 www.meas-spec.com 34200B Precision Aligned ±10 g to ±70 g Triaxial Accelerometer Superior Zero g Bias Stability Technical Data* Features and Benefits Precision Alignment Each axis of the Measurement Specialties 34200B is precision aligned to minimize errors due to axis misalignment or transverse sensitivity. High Accuracy and Linearity over Wide Temperature Range The voltage output for each axis of the 34200B is directly proportional to the acceleration along that axis. Each DC-coupled output is fully scaled, referenced, and temperature compensafted over the entire -40 to +85°C temperature range. Accuracy is improved by minimizing variations due to temperature and aging effects, resulting in a sensor that is more stable over temperature than piezoelectric or piezoresistive devices. Calibration Certificate Each 34200B is supplied with a calibration certificate listing sensitivity and offset, as well as the on-axis and transverse alignment parameters needed to ensure rapid and efficient system implementation. The alignment data can be used to compensate the measured values to achieve an even higher level of sensor accuracy. Self-Test on Digital Command A TTL-compatible self-test low input causes a simulated acceleration to be injected into all three sensors to verify channel integrity. Small Size Complete conditioned triaxial accelerometer in less than a cubic inch. uilt-In Power Supply Regulation B Unregulated DC power from +8.5 to +36 volts is all that is required to measure accelerations on all axes. Suitable for Harsh Environments The 34200B is robust and can be used in harsh environments. The unit will survive 4000 g powered or unpowered. Warranty These Measurement Specialties accelerometers come with a three-year factory warranty. 34200B Analog Rate Gyro precisionsensors.meas-spec.com Precisely Measure Real -World Accelerations Measurement Specialties’ 34200B accelerometer has each mutually orthogonal axis precisely aligned within 0.5 degree of the theoretical ideal. This provides the accuracy required by most measurement applications without any compensation. Critical applications requiring higher accuracy can use the alignment data provided on the calibration certificate to compensate for any small residual error. Choose the bandwidth and range options best suited for your application to measure ±10 g, ±15 g, ±20 g, ±25 g, ±30 g, ±35 g, ±40 g, ±50 g, or ±70 g accelerations on each of three axes. Each axial sensor has been tested over the -40 to +85°C temperature range and has a nominal full scale output swing of ±2 volts. The zero g output level is nominally +2.5 volts. Precise values for each axis are available on the included calibration certificate. 2236 N. Cleveland-Massillon Road Akron OH 44333 PH : 330-659-3312 8/5/2013 www.meas-spec.com Specifications for 34200B - improved specifications available upon request Ta = Tmin to Tmax; 8.5 ≤ Vs ≤ 36 V; Acceleration = 0 g unless otherwise noted; within one year of calibration. Parameter Min Units Conditions/Notes ±70 g On each axis. Must specify via Option Rnnn Sensitivity At 25°C, Option R050 Drift Tmin to Tmax 38† ±0.5 mV/g % Zero g Bias Level At 25°C Drift Tmin to Tmax 2.5 ±60 V mg Alignment Deviation from Ideal Axes ±0.2 Transverse Sensitivity ±0.25 Nonlinearity 0.2 Precise values on cal certificate Percent of sensitivity at 25°C Precise values on cal certificate At 1.25°C/min temperature rate of change Precise values on cal certificate Can be compensated if required ±0.5 degrees 2 % FSR 400†† Hz 3.5 3.0 3.0 mg/√Hz mg/√Hz mg/√Hz % Inherent sensor error, excluding misalignment Best fit straight line Frequency Response Noise Density Option R070 Option R050, R040 Option R035, R030, R025, R020, R015, R010 Self-Test Input Impedance 10 Temperature Sensor Sensitivity 0°C Bias Level Outputs Output Voltage Swing Capacitive Drive Capability 0.25 1000 4.75 V pF Iout = ±0.5 mA Power Supply (Vs) Input Voltage Limits Input Voltage - Operating Input Current Rejection Ratio -20 +8.5 15 >120 +38 +36 20 V V mA dB -20 V continuous Temperature Range (Ta) -40 +85 °C Mass Shock Survival -4000 linearly with range option Rnnn ††Per 0 1.8 1.4 1.1 2 3 3 1 2 6.45 509 1 1 0.945 0.354 Two 3 mm [24,00] [9,0] x 0.5 mm threaded holes are provided on each of three orthogonal faces for mounting. 34200B Analog Rate Gyro precisionsensors.meas-spec.com Precise values on cal certificate g Any axis for 0.5 ms, powered or unpowered Connections T004 2 Pin Signal Wire 0.354 [9,0] No load, quiescent DC Option Bnnn; See Ordering Information 3 0.945 [24,00] Accuracy ±1°C grams +4000 10 Hz to 400 Hz Pullup. Logic "1"≥ 3.5 V, Logic "0"≤ 1.5 V mV/°C mV 35 1.115 [28,30] 0.295 [7,50] 3 mm x 0,5 mm Thread 3,5 mm [0.138] Deep 0.295 [7,50] (6) Mounting Holes on 3 sides Upper cutoff per Option Bnnn, -3 dB pt ±10% kΩ Mechanical Max ±10 †Scale Typical Range Measurement Full Scale Dimensions in inches [mm], identical for each view where applicable. 1 A1+ Brown 2 Signal- Red 3 4 5 A2+ +5VOut A3+ Orange Yellow Green 6 7 8 T+ Self Test-L +Vs Blue Violet Grey 9 Gnd White Ordering Information 34200B - R050 - B400 - T004 Cable to 9-pin male D-Shell connector 3 1 2 Shown with 34170B mounting adapter (sold separately) Instrument Range R070 : ±70 g R050 : ±50 g R040 : ±40 g R035 : ±35 g R030 : ±30 g R025 : ±25 g R020 : ±20 g R015 : ±15 g R010 : ±10 g 2236 N. Cleveland-Massillon Road Akron OH 44333 PH : 330-659-3312 Termination T004 : 4 ft. cable with DB9M T000 : PCB mount (Not shown, Call SI) Tnnn : Custom length, nnn ft. (Call SI) Bandwidth B400 : 0 to 400 Hz B380 : 0 to 380 Hz B208 : 0 to 208 Hz B142 : 0 to 142 Hz B094 : 0 to 94 Hz B066 : 0 to 66 Hz B031 : 0 to 31 Hz B6.6 : 0 to 6.6 Hz 8/5/2013 www.meas-spec.com 13200C Uniaxial Rugged ±10 g to ±70 g Accelerometers with Superior Zero g Bias Stability 23200C Biaxial C Technical Data* Features and Benefits High Accuracy and Linearity over Wide Temperature Range The voltage output for the 13200C and 23200C is directly proportional to the acceleration along the axis. Each DC-coupled output is fully scaled, referenced, and temperature compensated. Accuracy is improved by minimizing variations due to temperature and aging effects, resulting in sensors that are more stable over temperature than piezoelectric or piezoresistive devices. Calibration Certificate Each 13200C and 23200C is supplied with a calibration certificate listing sensitivity and offset, as well as the on-axis and transverse alignment parameters needed to ensure rapid and efficient system implementation. The alignment data can be used to compensate the measured values if needed. Increased offset compensation can be obtained with Option C002. Self-Test on Digital Command A TTL-compatible self-test input causes a simulated acceleration to be injected into the accelerometer to verify channel integrity. Small Size Complete conditioned uniaxial or biaxial accelerometer in less than a cubic inch. uilt-In Power Supply Regulation B Unregulated DC power from +8.5 to +36 Volts is all that is required to measure acceleration and temperature. Reverse power voltages of up to -80 V can be withstood indefinitely. Transients of +80 V for 550 ms compatible with MIL-STD-704A can be withstood with full operation. Easy Installation Built-in terminal block or cable with 9-pin connector makes it easy to wire. Two through-holes and four tapped holes simplify mounting. uitable for Harsh Environments S The 13200C and 23200C are robust and can be used in harsh environments. The units will survive 4000 g powered or unpowered. Warranty These Measurement Specialties accelerometers come with a three-year factory warranty. 13200C.23200C Analog Accelerometer precisionsensors.meas-spec.com Simplify Acceleration and Temperature Measurements The Measurement Specialties 13200C and 23200C accelerometers include a temperature sensor in their small, rugged package. The small size and built-in power regulation allow the 13200C and 23200C to fit where other accelerometers can’t. Choose the bandwidth and range options best suited for your application to measure ±10 g, ±15 g, ±20 g, ±25 g, ±30 g, ±35 g, ±40 g, ±50 g, or ±70 g accelerations on one or two axes. The high repeatability of the builtin temperature sensor allows precise compensation of temperature effects. Alignment data provided on the included calibration certificate can be used to manually correct transverse sensitivity and alignment errors, or when extra precision is required, Option C002, offset compensation is available. Tested over the -40 to +85°C temperature range, the accelerometers have a nominal full scale output swing of ±2 Volts. The zero g output level is nominally +2.5 Volts. Precise values are available on the included calibration certificate. Custom versions of the 13200C and 23200C can be provided for applications which require different range and/or bandwidth. 2236 N. Cleveland-Massillon Road Akron OH 44333 PH : 330-659-3312 8/2/2013 www.meas-spec.com Specifications for 13200C and 23200C - improved specifications available upon request Ta = Tmin to Tmax; 8.5 ≤ Vs ≤ 36 V; Acceleration = 0 g unless otherwise noted; within one year of calibration. Parameter Min Typical Max Units Conditions/Notes ±70 g On each axis. Must specify via Option Rnnn Range Measurement Full Scale ±10 Sensitivity At 25°C, Option R050 Drift Tmin to Tmax 38† ±0.5 mV/g % Zero g Bias Level At 25°C Drift Tmin to Tmax, Option C001 Drift Tmin to Tmax, Option C002 2.5 1 60 V g mg Alignment Deviation from Ideal Axes ±1.0 Transverse Sensitivity ±0.25 Nonlinearity 0.2 2 % FSR Frequency Response 0 400 Hz Noise Density Option R070 Option R050, R040 Option R035, R030, R025, R020, R015, R010 3.5 3.0 3.0 mg/√Hz mg/√Hz mg/√Hz Self-Test Input Impedance 10 Temperature Sensor Sensitivity 0°C Bias Level Outputs Output Voltage Swing Capacitive Drive Capability 0.05 1000 Power Supply (Vs) Input Voltage Limits Input Voltage - Operating Input Current Rejection Ratio ±3.0 Precise values on cal certificate Percent of sensitivity at 25°C Precise values on cal certificate At 1.25°C/min. temperature rate of change At 1.25°C/min. temperature rate of change Precise values on cal certificate Can be compensated if required degrees % 1.8 1.4 1.1 Inherent sensor error, excluding misalignment Best fit straight line Upper cutoff per Option Bnnn, -3dB pt ±10% 10 Hz to 400 Hz kΩ 6.45 509 Pullup. Logic "1"≥ 3.5 V, Logic "0"≤ 1.5 V Accuracy ±1°C mV/°C mV 4.95 V pF Iout = ±0.5 mA -80 +8.5 12 >120 +80 +36 V V mA dB -80 V continuous, >38 V if ≤550 ms, duty <1% Continuous Temperature Range (Ta) -40 +85 Mass Shock Survival †Scale DC °C 35 grams -4000 +4000 Precise values on cal certificate g Any axis for 0.5 ms, powered or unpowered linearly with range option Rnnn; see Ordering Information Mechanical Connections T000 Pin Signal Wire Spring and cable added with cable options T004 1 A2+ Brown Mounting adapters (sold separately) 35173A Horizontal 13200C.23200C Analog Accelerometer precisionsensors.meas-spec.com 3 4 5 T+ +5VOut A1+ Orange Yellow Green 6 7 Signal- Self Test Blue Violet 8 +Vs Grey 9 Gnd White Ordering Information 23200C Two through holes and four 3 mm x 0.5 mm threaded holes are provided for mounting. 2 Signal- Red R070 23200C 13200C Range R070 : ±70 g R050 : ±50 g R040 : ±40 g R035 : ±35 g R030 : ±30 g R025 : ±25 g R020 : ±20 g R015 : ±15 g R010 : ±10 g B400 T004 Bandwidth B400 : 0 to 400 Hz B380 : 0 to 380 Hz B208 : 0 to 208 Hz B142 : 0 to 142 Hz B094 : 0 to 94 Hz B066 : 0 to 66 Hz B031 : 0 to 31 Hz B6.6 : 0 to 6.6 Hz C002 Calibration C001 : Std room temp calibration only C002 : C001 cal plus -40 to +85°C offset compensation Termination T004 : 4 ft. cable with DB9M T000 : Terminal Block Tnnn : Custom length, nnn ft. (call SI) 35172A Vertical 2236 N. Cleveland-Massillon Road Akron OH 44333 PH : 330-659-3312 8/2/2013 www.meas-spec.com PRELIMINARY 13207A Uniaxial ±10 g to ±70 g Accelerometers with Wide Bandwidth to 10 kHz 23207A Biaxial 00001 1911A Technical Data* Features and Benefits High Accuracy and Linearity over Wide Temperature Range The Voltage output for each axis of the 13207A and 23207A is directly proportional to the acceleration along that axis. Each DC-coupled output is fully scaled, referenced, and temperature compensated. Accuracy is improved by minimizing variations due to temperature and aging effects, resulting in a sensor that is more stable over temperature than piezoelectric or piezoresistive devices. Calibration Certificate Each 13207A and 23207A is supplied with a calibration certificate listing sensitivity and offset, as well as the on-axis and transverse alignment parameters needed to ensure rapid and efficient system implementation. The alignment data can be used to compensate the measured values to achieve an even higher level of sensor accuracy. Self-Test on Digital Command A TTL-compatible self-test low input causes a simulated acceleration to be injected into the sensor(s) to verify channel integrity. Small Size Complete conditioned uniaxial or biaxial accelerometer in less than a cubic inch. uilt-In Power Supply Regulation B Unregulated DC power from +8.5 to +36 Volts is all that is required to measure acceleration and temperature. Reverse power voltages of up to -80 V can be withstood indefinitely. Transients of +80 V for 550 ms compatible with MIL-STD-704A can be withstood with full operation. Easy Installation Built-in terminal block or cable with 9-pin connector makes it easy to wire. Two through-holes and four tapped holes simplify mounting. Suitable for Harsh Environments The 13207A and 23207A are robust and can be used in harsh environments. The units will survive 4000 g powered or unpowered. Warranty These Measurement Specialties accelerometers come with a three-year factory warranty 13207A.23207A Analog Accelerometer precisionsensors.meas-spec.com Simplify Acceleration and Temperature Measurements The Measurement Specialties 13207A and 23207A accelerometers include a temperature sensor in their small, rugged package. The small size and built-in power regulation allow the 13207A and 23207A to fit where other accelerometers can’t. Choose the bandwidth and range options best suited for your application to measure ±10 g, ±20 g, ±30 g, ±40 g, ±50 g, ±60 g, or ±70 g accelerations on one or two axes. The high repeatability of the builtin temperature sensor allows precise compensation of temperature effects. Alignment data provided on the included calibration certificate can be used to manually correct transverse sensitivity and alignment errors, or when extra precision is required, Option C002, offset compensation is available. Tested over the -40 to +85°C temperature range, the accelerometers have a nominal full scale output swing of ±2 Volts. The zero g output level is nominally +2.5 Volts. Precise values are available on the included calibration certificate. Custom versions of the 13207A and 23207A can be provided for applications which require different range and/or bandwidth. 2236 N. Cleveland-Massillon Road Akron OH 44333 PH : 330-659-3312 7/18/2013 www.meas-spec.com PRELIMINARY Specifications for 13207A and 23207A - improved specifications available upon request Ta = Tmin to Tmax; 8.5 ≤ Vs ≤ 36 V; Acceleration = 0 g unless otherwise noted; within one year of calibration. Parameter Min Typical Max Units ±70 g Conditions/Notes Accelerometers Full Scale Range ±10 Sensitivity At 25°C, Option R070 Drift Tmin to Tmax ±29† ±0.5 Zero g Bias Level At 25°C Drift Tmin to Tmax, Option C001 Drift Tmin to Tmax, Option C002 2.5 ±1.5 ±250 Alignment Deviation from Ideal Axes ±1.0 Transverse Sensitivity ±0.25 Nonlinearity 0.2 Frequency Response Noise Density Self-Test Input Impedance 10 Temperature Sensor Sensitivity 0°C Bias Level Outputs Output Voltage Swing Capacitive Drive Capability 0.25 1000 4.75 V pF Iout = ±0.5 mA Power Supply (Vs) Input Voltage Limits Input Voltage - Operating Input Current Rejection Ratio -80 +8.5 15 >120 +80 +36 20 V V mA dB -80V continuous, >38 V if ≤550 ms, duty <1% Continuous No load, quiescent DC Temperature Range (Ta) -40 +85 °C Mass Shock Survival -4000 †Scale 0 On each axis, specify with Option Rnnn mV/g % Percent of sensitivity at 25°C V g mg ±3.0 degree 2 % FSR Precise values on cal certificate At 1.25°C/min temperature rate of change At 1.25°C/min temperature rate of change Precise values on cal certificate Can be compensated if required % 10 4 Inherent sensor error, excluding misalignment Best fit straight line kHz Upper cutoff per Option Bnnn, -3 dB pt ±10% mg/√Hz kΩ 6.45 509 mV/°C mV 35 grams +4000 g Pullup. Logic "1"≥3.5V, Logic "0"≤1.5V Accuracy ±1°C Precise values on cal certificate Any axis for 0.5ms, powered or unpowered linearly with range option Rnnn. Mechanical Connections T000 Pin Signal Wire Spring and cable added with cable options T004 1 A2+ Brown 2 Signal- Red 3 4 5 T+ +5VOut A1+ Orange Yellow Green 6 7 Signal- Self Test Blue Violet 8 +Vs Grey 9 Gnd White Ordering Information 23207A - R070 - B1k0 - T004 - C002 Two through holes and four 3 mm x 0.5 mm threaded holes are provided for mounting. Instrument 23207A 13207A Mounting adapters (sold separately) 35173A Horizontal 13207A.23207A Analog Accelerometer precisionsensors.meas-spec.com Range R070 : ±70 g R060 : ±60 g R050 : ±50 g R040 : ±40 g R030 : ±30 g R020 : ±20 g R010 : ±10 g Calibration C001 : Std room temp calibration only C002 : C001 cal plus -40 to +85°C offset compensation Termination T004 : 4 ft. cable with DB9M T000 : Terminal block Tnnn : Custom length, nnn ft. (call SI) Bandwidth B10k : 0 to 10 kHz B5k0 : 0 to 5 kHz B1k0 : 0 to 1 kHz 35172A Vertical 2236 N. Cleveland-Massillon Road Akron OH 44333 PH : 330-659-3312 7/18/2013 www.meas-spec.com 34206A ±100 g Triaxial Accelerometer Superior Zero g Bias Stability Low Noise - Wide Bandwidth 5 8 Technical Data* Features and Benefits High Accuracy and Linearity over Wide Temperature Range The voltage output for each axis of the 34206A is directly proportional to the acceleration along that axis. Each DC-coupled output is fully scaled, referenced, and temperature compensated over the entire -40 to +85°C temperature range. Calibration Certificate Each 34206A is supplied with a calibration certificate listing sensitivity and offset, as well as the on-axis and transverse alignment parameters needed to ensure rapid and efficient system implementation. The alignment data can be used to compensate the measured values to achieve an even higher level of sensor accuracy. Small Size Complete conditioned triaxial accelerometer in less than a cubic inch. uilt-In Power Supply Regulation B Unregulated DC power from +8 to +18 volts is all that is required to measure accelerations on all axes. Suitable for Harsh Environments The 34206A is robust and can be used in harsh environments. The unit will survive 5000 g powered or unpowered. Warranty These Measurement Specialties accelerometers come with a three-year factory warranty. 34206A Triaxial Analog Accelerometer precisionsensors.meas-spec.com Precisely Measure Real-World Accelerations Measurement Specialties’ 34206A accelerometer provides the accuracy required by most measurement applications without any compensation. Critical applications requiring higher accuracy can use the alignment data provided on the calibration certificate to compensate for any small residual error. Choose the bandwidth option best suited for your application to measure ±100 g accelerations on each of three axes. Each axial sensor has been tested over the -40 to +85°C temperature range and has a nominal full scale output swing of ±2.25 volts. The zero g output level is nominally +2.5 volts. Precise values for each axis are available on the included calibration certificate. 2236 N. Cleveland-Massillon Road Akron OH 44333 PH : 330-659-3312 8/5/2013 www.meas-spec.com Specifications for 34206A - improved specifications available upon request Ta = Tmin to Tmax; 8 ≤ Vs ≤ 18 V; Acceleration = 0 g unless otherwise noted; within one year of calibration. Max Units Range Measurement Full Scale Parameter Min Typical ±100 g Sensitivity At 25°C Drift Tmin to Tmax 20 ±2.0 mV/g % Nom ±100 g. Precise values on cal certificate Percent of sensitivity at 25°C Zero g Bias Level At 25°C Drift Tmin to Tmax 2.5 ±80 ±200 V mg Precise values on cal certificate At <1.25°C/min temperature rate of change Alignment Deviation from Ideal Axes ±0.35 ±3.0 degrees Precise values on cal certificate Can be compensated if required Nonlinearity 0.25 1 % FSR Best fit straight line Frequency Response 2500 Hz Noise Density 100 μg/√Hz Temperature Sensor Sensitivity 0°C Bias Level 6.45 509 mV/°C mV Outputs Output Voltage Swing Capacitive Drive Capability 0.25 500 4.75 V pF Iout = ±0.5 mA Power Supply (Vs) Input Voltage - Operating Input Current Rejection Ratio +8 33 >120 +18 50 V mA dB Will withstand -20 V continuous or 36 V for <1 sec. No load, quiescent DC Temperature Range (Ta) -40 +85 Mass Shock Survival -5000 0 Mechanical 35 Upper Cutoff per Option Bnnn, -3 dB pt ±10% Ta =25°C Accuracy ±1°C typical °C grams +5000 Conditions/Notes On each axis g Precise values on cal certificate Any axis for 0.1 ms, powered or unpowered Connections T004 Pin Signal Wire 1 A1+ Brown 2 3 4 5 Signal- A2+ +5VOut A3+ Red Orange Yellow Green 6 T+ Blue 7 N.C. Violet 8 +Vs Grey 9 Gnd White Ordering Information 34206A Two 3 mm x 0.5 mm threaded holes are provided on each of three orthogonal faces for mounting. 34206A Triaxial Analog Accelerometer precisionsensors.meas-spec.com - R100 - B2k5 Instrument 34206A Range R100 : ±100 g Shown with 34170B mounting adapter (sold separately) Bandwidth B2k5 : 0 to 2500 Hz B2k1 : 0 to 2100 Hz B1k4 : 0 to 1400 Hz B944 : 0 to 944 Hz B380 : 0 to 380 Hz B208 : 0 to 208 Hz 2236 N. Cleveland-Massillon Road Akron OH 44333 PH : 330-659-3312 - T004 Termination T004 : 4 ft. cable with DB9M T000 : PCB Mount (Not shown, Call SI) Tnnn : Custom length, nnn ft. (Call SI) 8/5/2013 www.meas-spec.com PRELIMINARY 34208A ±250 g, ±500 g Triaxial Accelerometer Wide Bandwidth to 10 kHz Precision Aligned This Measurement Specialties product is subject to U.S. Export Law. Technical Data* 8 001 0000A00 Features and Benefits Precision Alignment Each axis of the Measurement Specialties 34208A is precision aligned to minimize errors due to axis misalignment or transverse sensitivity. High Accuracy and Linearity over Wide Temperature Range The voltage output for each axis of the 34208A is directly proportional to the acceleration along that axis. Each DC-coupled output is fully scaled, referenced, and temperature compensated over the entire -40 to +85°C range. Accuracy is improved by minimizing variations due to temperature and aging effects, resulting in a sensor that is more stable over temperature than piezoelectric or piezoresistive devices. Calibration Certificate Each 34208A is supplied with a calibration certificate listing sensitivity and offset, as well as on-axis and transverse alignment parameters needed to ensure rapid and efficient system implementation. The alignment data can be used to compensate the measured values to achieve an even higher level of sensor accuracy. Self-Test on Digital Command A TTL-compatible self-test low input causes a simulated acceleration to be injected into all three sensors to verify channel integrity. Small Size Complete conditioned triaxial accelerometer in less than a cubic inch. uilt-In Power Supply Regulation B Unregulated DC power from +8.5 to +36 volts is all that is required to measure acceleration and temperature. Suitable for Harsh Environments The 34208A is robust and can be used in harsh environments. The unit will survive 4000 g powered or unpowered. Warranty These Measurement Specialties accelerometers come with a three-year factory warranty. 34208A Triaxial Analog Accelerometers precisionsensors.meas-spec.com Precisely Measure Real -World Accelerations The Measurement Specialties 34208A accelerometer has each mutually orthogonal axis precisely aligned within 0.75 degree of the theoretical ideal. This provides the accuracy required by most measurement applications without any compensation. Critical applications requiring higher accuracy can use the alignment data provided on the calibration certificate to compensate for any small residual error. Choose the bandwidth and range options best suited for your application to measure up to ±250 g or ±500 g accelerations on each of three axes. Each axial sensor has been tested over the -40 to +85°C temperature range and has a nominal full scale output swing of ±2 volts. The zero g output level is nominally +2.5 volts. Precise values for each axis are available on the included calibration certificate. 2236 N. Cleveland-Massillon Road Akron OH 44333 PH : 330-659-3312 8/19/2013 www.meas-spec.com PRELIMINARY Specifications for 34208A - improved specifications available upon request Ta = Tmin to Tmax; 8.5 ≤ Vs ≤ 36 V; Acceleration = 0 g unless otherwise noted; within one year of calibration. Parameter Min Accelerometers Full Scale Range Option R250 Option R500 Sensitivity at 25°C Option R250 Option R500 Drift Tmin to Tmax Units Conditions/Notes On each axis, specify with Option Rnnn g g ±6.6 ±3.3 1% (TBD) mV/g mV/g % 2.5 ±1000 Percent of sensitivity at 25°C V mg Precise values on cal certificate ±0.75 degree Precise values on cal certificate Can be compensated if required 2 % FSR Alignment Deviation from Ideal Axes Transverse Sensitivity ±0.25 Nonlinearity 0.2 Frequency Response Noise Density Self-Test Input Impedance 10 Temperature Sensor Sensitivity 0°C Bias Level Outputs Output Voltage Swing Capacitive Drive Capability 0.25 1000 4.75 V pF Iout = ±0.5 mA Power Supply (Vs) Input Voltage Limits Input Voltage - Operating Input Current Rejection Ratio -20 +8.5 15 >120 +38 +36 20 V V mA dB -20V continuous Temperature Range (Ta) -40 +85 °C Mass Shock Survival -4000 0 2 10 3 1 2 0.945 0.354 Two 3 mm [24,00] [9,0] x 0.5 mm threaded holes are provided on each of three orthogonal faces for mounting. 34208A Triaxial Analog Accelerometers precisionsensors.meas-spec.com kHz Upper cutoff per Option Bnnn, -3 dB pt ±10% 35 Accuracy ±1°C No load, quiescent DC grams +4000 10 Hz to 400 Hz Pullup. Logic "1"≥3.5V, Logic "0"≤1.5V mV/°C mV Precise values on cal certificate g Any axis for 0.5ms, powered or unpowered Connections 3 1 1 T004 2 Pin Signal Wire 0.945 [24,00] 0.354 [9,0] Dimensions in inches [mm], identical for each view where applicable. 1 A1+ Brown 3 4 5 A2+ +5VOut A3+ Orange Yellow Green 6 7 8 T+ Self Test-L +Vs Blue Violet Grey 9 Gnd White 34208A - R500 - B1k0 - T004 Termination T004 : 4 ft. cable with DB9M T000 : PCB mount (not shown, call SI) Tnnn : Custom length, nnn ft. (call SI) Bandwidth B10k : 0 to 10 kHz B5k0 : 0 to 5 kHz B2k5 : 0 to 2.5 kHz B1k0 : 0 to 1 kHz Range R500 : ±500 g R250 : ±250 g 1 2 Shown with 34170B mounting adapter (sold separately) 2 Signal- Red Ordering Information Cable to 9-pin male D-Shell connector 3 Best fit straight line mg/√Hz 6.45 509 1.115 [28,30] 0.295 [7,50] 3 mm x 0,5 mm Thread 3,5 mm [0.138] Deep 0.295 [7,50] (6) Mounting Holes on 3 sides Inherent sensor error, excluding misalignment kΩ 3 % ±2.8 Mechanical Max ±250 ±500 Zero g Bias Level At 25°C Drift Tmin to Tmax At 1.25°C/min rate of change Typical Instrument 2236 N. Cleveland-Massillon Road Akron OH 44333 PH : 330-659-3312 8/12/2013 www.meas-spec.com 35172A Mounting Adapter for Vertical Mounting of Vertical Mounting of Digital Accelerometer Measurement Specialties Digital and Non-cubical Analog Accelerometers Vertical Mounting of Non-cubical Analog Accelerometer Technical Data * Simplify Accelerometer Mounting Features and Benefits Precision Machined Faces of mounting plate are machined parallel to minimize errors. Low Mass Aluminum The 35172A is fabricated from 6061-T6 aluminum to reduce mass while providing optimal rigidity. Convenience The 35172A mounting adapter simplifies accelerometer mounting when the system to be measured can be accessed from only one side, and a vertical mounting is desired. When access from both sides is possible, the 35172A can be used as an alternate to the accelerometer’s integral mount. 0.295 REF [7.48] 0.295 [7.48] 0.127 [3.23] The 35172A mounting adapter makes it easy to mount a Measurement Specialties digital or non-cubical analog accelerometer when it is not convenient to use the accelerometer’s integral mount. Four 3.0 x 6 mm socket flat head screws are included to attach a digital sensor to the adapter (two for analog). The adapter with accelerometer can then be mounted to the object under test using M3, M3.5, or #6 screws. To prevent screws from loosening due to vibrations, a locking compound is recommended for all threads. 0.354 [8.99] 0.188 [4.76] 0.354 [8.99] 1.437 [36.50] Ø 0.134 THRU Ø 0.289 [7.33] X 90° (4) Places 0.354 [8.99] 1.062 [26.97] 0.354 [8.99] REF 0.118 [3.00] Dimensions in inches [mm] Tolerances ±0.005 [0.127] 35172A Mounting Adapter precisionsensors.meas-spec.com Ø 0.147 [3.73] THRU (4) Places 0.943 [23.95] 1.197 [30.40] Third angle 2236 N. Cleveland-Massillon Road Akron OH 44333 PH : 330-659-3312 8/12/2013 www.meas-spec.com 35173A Mounting Adapter for Horizontal Mounting of Measurement Specialties Non-cubical Analog Accelerometers Technical Simplify Accelerometer Mounting Data * Features and Benefits Precision Machined Faces of mounting plate are machined parallel to minimize errors. Low Mass Aluminum The 35173A is fabricated from 6061-T6 aluminum to reduce mass while providing optimal rigidity. Convenience The 35173A mounting adapter simplifies accelerometer mounting when the system to be measured can be accessed from only one side, and a horizontal mounting is desired. When access from both sides is possible, the 35173A can be used as an alternate to the accelerometer’s integral mount. 0.450 11.42 0.127 3.23 Measurement Specialties’ 35173A mounting adapter makes it easy to mount most Measurement Specialties uniaxial, biaxial, or XL403 accelerometers when it is not convenient to use the accelerometer’s integral mount. Two 3.0 x 6 mm socket flat head screws are included to attach the sensor to the adapter. The adapter with accelerometer can then be mounted to the object under test using M3, M3.5, or #6 screws. To prevent screws from loosening due to vibrations, a locking compound is recommended for all threads. 0.354 8.99 0.450 REF 11.42 0.188 4.76 0.354 8.99 1.437 36.50 0.134 THRU 0.289 7.33 X 90° (4) Places 0.354 8.99 1.062 26.97 0.147 3.73 THRU (4) Places 0.354 8.99 REF 0.118 3.00 1.253 31.83 Dimensions in inches [mm] Tolerances ±0.005 [0.127] 1.507 38.28 35173A Mounting Adapter precisionsensors.meas-spec.com 2236 N. Cleveland-Massillon Road Akron OH 44333 PH : 330-659-3312 Third angle 8/12/2013 www.meas-spec.com 34170B Mounting Adapter for use with Measurement Specialties Cubical Accelerometers and Rate Gyros Technical Simplify Cubical Sensor Mounting Data * Features and Benefits Precision Machined Faces of mounting plate are machined parallel to minimize errors. Low Mass Aluminum The 34170B is fabricated from 6061-T6 aluminum to reduce mass while providing optimal rigidity. Convenience The 34170B mounting adapter simplifies accelerometer or rate gyro mounting when the system to be measured can be accessed from only one side. When access from both sides is possible, the 34170B can be used as an alternate to the sensor’s integral mount. 0.178 4.52 0.118 3.00 0.946 24.03 0.710 18.03 0.414 10.52 0.354 8.99 Measurement Specialties’ 34170B mounting adapter makes it easy to mount a Measurement Specialties accelerometer or rate gyro when it is not convenient to use the accelerometer’s integral mount. Two 3.0 x 6 mm socket flat head screws are included to attach the sensor to the adapter. The adapter with sensor can then be mounted to the object under test using M3, M3.5, or #6 screws. To prevent screws from loosening due to vibrations, a locking compound is recommended for all threads. 0.414 REF 10.52 0.134 THRU 0.288 7.30 X 90° (4) Places 0.354 8.99 0.147 3.73 THRU (4) Places 0.118 REF 3.00 0.178 REF 4.52 0.118 3.00 1.182 30.02 0.118 REF 3.00 1.418 36.02 0.118 3.00 Dimensions in inches [mm] Tolerances ±0.005 [0.127] 34170B Mounting Adapter precisionsensors.meas-spec.com Third angle 2236 N. Cleveland-Massillon Road Akron OH 44333 PH : 330-659-3312 8/5/2013 www.meas-spec.com