Optoway SPS-9110FG 1 *********************************************************************************************************************************************************************** SPS-9110FG / SPS-9110AFG (RoHS Compliant) 3.3V / 1310 nm / 2.125 Gbps LC SFP SINGLE-MODE TRANSCEIVER ********************************************************************************************************************************************************************** FEATURES DESCRIPTION l l l l l l l l l l l l The SPS-9110FG series single mode transceivers is small form factor pluggable module for bi-directional serial optical data communications such as Gigabit Ethernet 1000BASE-LX and Fibre Channel 1x/2x SM-LC-L FC-PI. It is with the SFP 20-pin connector to allow hot plug capability. This module is designed for single mode fiber and operates at a nominal wavelength of 1310 nm. The transmitter section uses a multiple quantum well laser and is a class 1 laser compliant according to International Safety Standard IEC-60825. The receiver section uses an integrated InGaAs detector preamplifier (IDP) mounted in an optical header and a limiting post-amplifier IC. Hot-Pluggable SFP Footprint LC Optical Transceiver Small Form-Factor Pluggable (SFP) MSA compatible Compliant with Fibre Channel 1X/2X SM-LC-L FC-PI Compliant with IEEE 802.3z 1000BASE-LX 1310 nm LD Transmitter Distance up to 10 km AC/AC Coupling according to MSA Single +3.3 V Power Supply RoHS Compliant -10 to 85oC Operation: SPS-9110FG -40 to 85oC Operation: SPS-9110AFG Class 1 Laser International Safety Standard IEC 60825 Compliant APPLICATIONS l l l l LASER SAFETY This single mode transceiver is a Class 1 laser product. It complies with IEC 60825 and FDA 21 CFR 1040.10 and 1040.11. The transceiver must be operated within the specified temperature and voltage limits. The optical ports of the module shall be terminated with an optical connector or with a dust plug. ATM Switches and Routers SONET / SDH Switch Infrastructure XDSL Applications Metro Edge Switching ORDER INFORMATION P/No. SPS-9110FG SPS-9110AFG Bit Rate (Gb/s) 2.125/1.063 2.125/1.063 FC-PI 200/100 200/100 Distance (km) 10 10 Wavelength Package (nm) 1310 LC SFP 1310 LC SFP Temp. TX Power RX Sens. RoHS (oC) (dBm) (dBm) Compliant -10 to 85 -3 to -8 -21 Yes -40 to 85 -3 to -8 -21 Yes Absolute Maximum Ratings Parameter Storage Temperature Operating Case Temperature Power Supply Voltage Symbol Tstg Topr Vcc Min -40 -10 -40 -0.5 Max 85 85 85 3.6 Units o C o C Min 3.1 -10 -40 Typ 3.3 Max 3.5 85 85 300 Notes SPS-9110FG SPS-9110AFG V Recommended Operating Conditions Parameter Power Supply Voltage Operating Case Temperature Power Supply Current Data Rate Symbol Vcc Topr ICC (TX+RX) 1000 200 2125 Units / Notes V o C / SPS-9110FG o C / SPS-9110AFG mA Mb/s *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: [email protected] http: // www.optoway.com.tw 1/1/2008 V2.0 Optoway SPS-9110FG 2 *********************************************************************************************************************************************************************** Transmitter Specifications (-10 oC < Topr < 85 oC, 3.1V < Vcc < 3.5V) Parameter Symbol Min Typ Max Optical Optical Transmit Power Po -8 ---3 Output Center Wavelength 1270 1310 1350 λ Output Spectrum Width ----2.5 ∆λ Extinction Ratio ER 9 --Optical Modulation Amplitude OMA 174 (Peak-to-Peak) Optical Rise Time tr 160 Optical Fall Time tf 160 Relative Intensity Noise RIN -120 Electrical Data Input Current – Low IIL -350 Data Input Current – High IIH 350 Differential Input Voltage VIH - V IL 0.5 2.4 TX Disable Input Voltage – Low TDIS, L 0 0.5 TX Disable Input Voltage – High TDIS, H 2.0 Vcc TX Disable Assert Time T ASSERT 10 TX Disable Deassert Time TDEASSERT 1 TX Fault Output Voltage -- Low TFaultL 0 0.8 TX Fault Output Voltage -- High TFaultH 2.0 Vcc+0.3 1. Output power is power coupled into a 9/125 µm single mode fiber. 2. There is an internal 4.7K to 10K ohm pull-up resistor to VccTX. 3. Open collector compatible, 4.7K to 10K ohm pull-up to Vcc (Host Supply Voltage). Units Notes dBm nm nm dB µW 1 ps ps dB/Hz µA µA V V V µs ms V V RMS (σ) FC-PI Standard 20 % to 80% Values 20 % to 80% Values Peak-to-Peak 2 2 3 3 Receiver Specifications (-10oC < Topr < 85oC, 3.1V < Vcc < 3.5V) Parameter Symbol Min Typ Max Units SENS (2X) SENS (1X) Pin Pa Pd --- --- -21 -22 dBm dBm dBm dBm dBm dB nm Notes Optical Sensitivity @2.125Gb/s @ BER=10-12 Sensitivity @1.25Gb/s @ BER=10-12 Maximum Input Power -3 Signal Detect -- Asserted ---21 Signal Detect -- Deasserted -30 ----Signal detect -- Hysteresis 1.0 --Wavelength of Operation 1100 --1600 Electrical Differential Output Voltage VOH – VOL 0.6 2.0 Output LOS Voltage -- Low VOL 0 0.8 Output LOS Voltage -- High VOH 2.0 Vcc+0.3 4. Measured at 2 7-1 PRBS at BER 1E-12 @ 1300 nm. 5. Open collector compatible, 4.7K to 10K ohm pull-up to Vcc (Host Supply Voltage). V V V 4 4 4 Transition: low to high Transition: high to low 5 5 *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: [email protected] http: // www.optoway.com.tw 1/1/2008 V2.0 Optoway SPS-9110FG 3 *********************************************************************************************************************************************************************** CONNECTION DIAGRAM PIN Signal Name 1 2 3 TX GND TX Fault TX Disable 4 MOD-DFE2 5 MOD-DEF1 6 MOD-DEF0 7 8 9 10 N/C LOS RX GND RX GND Description PIN Signal Name Description Transmitter Ground Transmitter Fault Indication Transmitter Disable (Module disables on high or open) Modulation Definition 2 – Two wires serial ID Interface Modulation Definition 1 – Two wires serial ID Interface Modulation Definition 0 – Ground in Module Not Connected Loss of Signal Receiver Ground Receiver Ground 11 12 13 RX GND Receiver Ground RX DATA OUT- Inverse Receiver Data Out RX DATA OUT+ Receiver Data Out 14 RX GND Receiver Ground 15 Vcc RX Receiver Power – 3.3V±5% 16 Vcc TX Transmitter Power – 3.3V±5% 17 18 19 20 TX GND TX DATA IN+ TX DATA INTX GND Transmitter Ground Transmitter Data In Inverse Transmitter Data In Transmitter Ground Module Definition Module Definition 4 MOD-DEF2 PIN 4 SDA MOD-DEF1 PIN 5 SCL MOD-DEF0 PIN 6 LV-TTL Low Interpretation by Host Serial module definition protocol Module Definition 4 specifies a serial definition protocol. For this definition, upon power up, MOD-DEF(1:2) appear as no connector (NC) and MOD-DEF(0) is TTL LOW. When the host system detects this condition, it activates the serial protocol. The protocol uses the 2-wire serial CMOS E 2PROM protocol of the ATMEL AT24C01A/02/04 family of components. *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: [email protected] http: // www.optoway.com.tw 1/1/2008 V2.0 Optoway SPS-9110FG 4 *********************************************************************************************************************************************************************** RECOMMENDED CIRCUIT SCHEMATIC VeeT Tx_DISABLE Tx_FAULT (1,17,20) 3 Tx_DISABLE 2 Tx_FAULT 4.7K to 10KΩ TD + LD Driver 18 TD + Z=50Ω 100Ω TD - 19 TD Z=50Ω VccT 1μH 16 Vcc 3.3V 10μF 10nF 10μF 10nF SerDes IC 1μH VccR 15 10μF 10nF RD - 12 Protocol IC RD Z=50Ω 100Ω POST Amp RD + 13 RD + Z=50Ω 4.7K to 10KΩ LOS VeeR MOD_DEF(0) EEPROM MOD_DEF(1) MOD_DEF(2) SFP module depending on SERDES 8 LOSS OF SINGAL (9,10,11,14) 6 MODULE DETECT 5 SCL 4 SDA 4.7K to 10KΩ 4.7K to 10KΩ Vcc 3.3V 4.7K to 10KΩ PACKAGE DIAGRAM Units in mm Note: Specifications subject to change without notice. *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: [email protected] http: // www.optoway.com.tw 1/1/2008 V2.0 Optoway SPS-9110FG 5 *********************************************************************************************************************************************************************** Revision History Version 1.0 2.0 Subject Initial datasheet Revise package diagram for high port density use Release Date 2005/12/1 2008/1/1 *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: [email protected] http: // www.optoway.com.tw 1/1/2008 V2.0