PART NUMBERING GUIDE

PART NUMBERING GUIDE
ABRACON QUARTZ CRYSTAL
Explanation of Ordering Options for Quartz Crystals. EXAMPLE: AB-70.0 MHz-20-R80-D-3-W-O-L1-T
AB
40.0 MHz
20
R15
3
D
W
F
L1
T
Part Number - Frequency - Cap. Load - ESR - Operating Temperature - Tolerance - Stability - Mode - Value Added - Packaging
Found at top
of each page
Enter desired
frequency in
MHz or kHz
Load
Capacitance
in pF or
-S for Series
Frequency at 25°C
-H5 for ± 5 ppm
-1 for ± 10 ppm
-7 for ± 15 ppm
-2 for ± 20 ppm
-3 for ± 25 ppm
-4 for ± 30 ppm
-5 for ± 100 ppm
or ± 50 ppm
Equivalent Series Resistance
RXXX (max. value in Ω)
-E for 0°C
- A for -10°C
-B for -20°C
-C for -30°C
-N for -30°C
-D for -40°C
to + 70°C
to + 60°C
to + 70°C
to + 70°C
to + 85°C
to + 85°C
Frequency
Over Temperature
Reference to 25°C
-R 3 for ± 3 ppm
-R 5 for ± 5 ppm
-U for ± 10 ppm
-X for ± 20 ppm
-W for ± 25 ppm
-Y for ± 30 ppm
-H for ± 35 ppm
-Z for ± 50 ppm
- T for Tape & Reel
- P for Foam
- TY for Tray Packing
-I
-K
-L
-L1
-L2
-L3
-V
-M
-MJ
-QXX
-F for Fundamental AT
-FB for Fundamental BT
-O for 3rd OT
NOTE:
for Insulator Ta b
for Ceramic Lid
for 3rd Lead Welded
for 3rd Lead Soldered
for Middle 3rd Lead
for side 3rd Lead
for Vinyl Sleeving
for SMT Formed Leads
for Metal Jackets
for Trimmed Leads
Left blank if Standard. Default Parameter Value is found in Product Pages.
ABRACON CRYSTAL OSCILLATORS
Explanation of Ordering Options for Crystal Oscillators EXAMPLE: A C O - 20.0 MHz- D - K - S - A - 5 0 - G - T Y
ACO
20.0 MHz
D
K
S
A
50
X
G
TY
Part Number - Frequency - Operating Temperature - Stability - Duty Cycle - Tristate - 50 - Pulling - Value Added - Packaging
Found at top
of each page
Enter desired frequency in
MHz or kHz
-I for - 0°C
-D for -10°C
-E for -20°C
-F for -30°C
-N for -30°C
-L for -40°C
to + 50°C
to + 60°C
to + 70°C
to + 70°C
to + 85°C
to + 85°C
Overall Frequency
Stability
-Y for ± 10 ppm max
-J for ± 20 ppm max
-R for ± 25 ppm max
-K for ± 30 ppm max
-H for ± 35 ppm max
-B for ± 40 ppm max
-C for ± 50 ppm max
- A for
Tristate E/D
50pF
Output Drive
-S for 45 / 55%
-T for 47.5 / 52.5%
-S1 for 45 / 55%
-T1 for 47.5 / 52.5%
(-40°C to +125°C available on Specific Products.)
NOTE:
Left blank if Standard. Default Parameter Value is found in Product Pages.
@ 1/ 2
Vdd
Vdd
@ 1.4 Vdc
@ 1.4 Vdc
@ 1/ 2
-G
Gull Wing
-G2 Gull Wing
-GHT Gull Wing,
Reflow capable
-QXX (Trimmed Leads)
-H5 for 5.08 mm height
-H6 for 6.2 mm height
-IR for internal trimmer
X = VCXO Only
- N 15
- N 20
- N 25
- N 30
for
for
for
for
±
±
±
±
150 ppm min.
200 ppm min.
250 ppm min.
300 ppm min.
- T for Tape & Reel
- TY for Tray packing
The Part Numbering Matrix Guide is used for Reference ONLY.
Abracon does not guarantee the availability of all products with combination of parameters as specified above.
Please see details on product pages.
ABRACON IS
ISO 9001 / QS 9000
CERTIFIED
Abracon Corporation. 30332 Esperanza, Rancho Santa Margarita, California 92688 Ph 949.546.8000 | Fx 949.546.8001 | www.abracon.com | [email protected]