HWZT-RS LOW PROFILE LEADED CERAMIC RESONATOR HWZT-RS RoHS/RoHS II Compliant Pb in ceramic, exemption (7c-I) FEATURES: APPLICATIONS: • Low resonant impedance • Small size, Light weight. • Low cost timing solution . • Clock oscillation for microcontrollers • Telephones • Household electric appliances 5.5 x 3.0 x 5.0mm | | | | | | | | | | | | | | STANDARD SPECIFICATIONS: Parameters Frequency Range Resonant Impedance (Ro) Frequency Tolerance Frequency Stability Withstanding Voltage D.C. Voltage Rating Voltage A.C. Voltage Load Capacitance Insulation Resistance Operation Temperature Storage Temperature Aging Rate (Fosc) Minimum 6.01 Typical -0.5 -0.3 24 500 -25 -40 -0.3 30 Maximum 12.50 25 +0.5 +0.3 100 6 15 36 +85 +85 0.3 Units MHz Ω % % Vdc Vdc Vp-p. pF MΩ ºC ºC % Notes -25ºC to +85ºC 5 secs 10Vdc, 1min From initial value TEST CONDITION AND TEST CIRCUIT: Parts shall be measured under a condition (Temp.: 20±15°C, Humidity: 65±20% R.H.) unless the standard condition (Temp: 25±3°C, Humidity: 65±10% R.H.) is regulated to measure X: Ceramic Resonator C1=C2=30pF±20% OPTIONS & PART IDENTIFICATION: HWZT Frequency Frequency in MHz ABRACON IS ISO9001:2008 CE RTIFIED RS Packaging Blank: Bulk A: AMMO package* *AMMO package lead length 13.5mm Revised: 05.07.13 Visit www.abracon.com for Terms & Conditions of Sale 30332 Esperanza, Rancho Santa Margarita, California 92688 tel 949-546-8000| fax 949-546-8001| www.abracon.com | LOW PROFILE LEADED CERAMIC RESONATOR HWZT-RS RoHS/RoHS II Compliant Pb in ceramic, exemption (7c-I) HWZT-RS 5.5 x 3.0 x 5.0mm | | | | | | | | | | | | | | OUTLINE DRAWING: Bulk Pack AMMO Pack Dimension: mm Packaging: Bulk: 500pcs/plastic bag AMMO: 2000pcs/box Note: upon opening the original packaging, it is recommended that the product be used within 1 year. If the product will not be used within 1 year, it is recommended that the product be re-sealed in airtight packaging according to MSL 1 requirements to maintain solderability. CAUTION (1) Do not apply excess mechanical stress to the component body or terminations. Do not attempt to re-form or bend the components as this will cause damage to the component. (2) This component is not hermetically sealed. Do not clean or wash the component. (3) Reflow Soldering: Do not use strong acidity flux, such as flux with chlorine content of greater than 0.2wt% during Reflow Soldering. (4) Do not expose the component to open flame. (5) This specification applies to the functionality of the component as a single unit. (6) Storage Conditions: If the product is to be stored for a period greater than 1 year after the Delivery Date, it is recommended that customers confirm the solderability and characteristics for the product prior to use. (7) This product is not recommended for use in the following applications: Automotive, Medical, Military, Safety, or any other highreliability , life dependant applications. ContactAbracon Corporation prior to using this product when in doubt. ATTENTION: Abracon Corporation’s products are COTS – Commercial-Off-The-Shelf products; suitable for Commercial, Industrial and, where designated, Automotive Applications. Abracon’s products are not specifically designed for Military, Aviation, Aerospace, Life-dependant Medical applications or any application requiring high reliability where component failure could result in loss of life and/or property. For applications requiring high reliability and/or presenting an extreme operating environment, written consent and authorization from Abracon Corporation is required. Please contact Abracon Corporation for more information. ABRACON IS ISO9001:2008 CE RTIFIED Revised: 05.07.13 Visit www.abracon.com for Terms & Conditions of Sale 30332 Esperanza, Rancho Santa Margarita, California 92688 tel 949-546-8000| fax 949-546-8001| www.abracon.com |