ILX3485

TECHNICAL DATA
Low-Power, Slew-Rate-Limited RS-485/RS-422
Transceivers
Description
The ILX3485 is low-power transceivers for RS-485
and RS- 422 communication. IC contains one driver
and one receiver. The driver slew rates of the ILX3485
is not limited, allowing them to transmit up to 5Mbps.
These transceivers draw between 120µA and
500µA of supply current when unloaded or fully loaded
with disabled drivers. All parts operate from a single
3.3V supply. Drivers are short-circuit current limited and
are protected against excessive power dissipation by
thermal shutdown circuitry that places the driver outputs
into a high-impedance state. The receiver input has a
fail-safe feature that guarantees a logic-high output if
the input is open circuit.
ILX3485
ILX3485N Plastic
ILX3485D SOIC
ORDERING INFORMATION
Device
ILX3485N
ILX3485D
ILX3485DT
Operating
Temperature Range
Package
Shipping
TA = -40 to 85 C
DIP8
SOP8
SOP8
Tube
Tube
Tape & Reel
Features










Low Quiescent Current: 300µA
-7V to +12V Common-Mode Input Voltage Range
Three-State Outputs
80ns Propagation Delays, 5ns Skew
Half-Duplex Versions Available
Operate from a Single 3.3V Supply
Allows up to 32 Transceivers on the Bus
Data rate: 5 Mbps
Current-Limiting and Thermal Shutdown for Driver Overload Protection
Enhanced ESD Specifications:
±15kV IEC61000-4-2 Air Discharge
±8kV IEC61000-4-2 Contact Discharge
Pin Description
2012, February, ver. 04
ILX3485
ABSOLUTE MAXIMUM RATINGS
Supply Voltage (VCC) 7V
Continuous Power Dissipation (TA= +70°C)
Control Input Voltage -0.3V to 7V
8-Pin Plastic DIP (derate 9.09mW/°C above
+70°C) 727mW
Driver Input Voltage (DI) -0.3V to 7V
8-Pin SOP (derate 5.88mW/°C above +70°C)
471mW
Driver Output Voltage (A, B) -7.5V to +12.5V
Operating Temperature Ranges -40°C to
+85°C
Receiver Input Voltage (A, B) -7.5V to +12.5V
Storage Temperature Range -65°C to +160°C
Receiver Output Voltage (RO) -0.3V to (VCC+0.3V) Lead Temperature (soldering, 10sec) +300°C
* Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device.
These are stress ratings only and functional operation of the device at these or any other conditions beyond those
indicated under “recommended operating conditions” is not implied.
Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
DC ELECTRICAL CHARACTERISTICS
(VCC = 3.3V ±0.3V, TA = TMIN to TMAX, unless otherwise noted.) (Notes 1, 2)
PARAMETER
Differential Driver Output (no
load)
Differential Driver Output
(with load)
Change in Magnitude of Driver
Differential Output Voltage for
Complementary Output States
Driver Common-Mode Output
Voltage
Change in Magnitude of Driver
Common-Mode Output Voltage
for Complementary Output
States
Input High Voltage
SYMBOL
CONDITIONS
MIN
TYP
VOD1
∆VOD
R = 100Ω (RS-422)
R = 54Ω (RS-485), Figure 4
R = 54Ω or 50Ω, Figure 4
VOC
∆VOC
VOD2
MAX
UNITS
3
V
1
0.8
V
0.2
V
R = 54Ω or 100Ω, Figure 4
2
V
R = 54Ω or 100Ω, Figure 4
0.2
V
VIH
DE, DI, RE
Input Low Voltage
VIL
DE, DI, RE
0.8
V
Input Current
Input Current
(A, B)
IIN1
±2
µA
VTH
1.0
-0.8
0.2
mA
Receiver Differential Threshold
Voltage
Receiver Input Hysteresis
Receiver Output High Voltage
Receiver Output Low Voltage
Three-State (high impedance)
Output Current at Receiver
Receiver Input Resistance
DE, DI, RE
DE = 0V;
VIN = 12V
VCC = 0V or 3.35V VIN = -7V
-7V ≤ VCM ≤12V
IIN2
∆VTH
VOH
VOL
IOZR
RIN
VCM = 0V
IO = -1.5mA, VID = 200mV
IO = 2.5mA, VID = -200mV
0.4V ≤ VO ≤ 2.4V
-7V ≤ VCM ≤ 12V
2.0
V
-0.2
70
2.5
0.4
±1
12
V
mV
V
V
µA
kΩ
2012, February, ver. 04
ILX3485
DC ELECTRICAL CHARACTERISTICS (continued)
(VCC = 3.3V ±0.3V, TA = TMIN to TMAX, unless otherwise noted.) (Notes 1, 2)
PARAMETER
No-Load Supply Current
(Note 3)
SYMBOL
ICC
Driver Short-Circuit Current,
IOSD1
VO = High
Driver Short-Circuit Current
VO = Low
Receiver Short-Circuit Current
IOSD2
CONDITIONS
MIN
DE = VCC
RE = 0V or VCC
DE = 0V
-7V ≤ VO ≤ 12V (Note 4)
TYP
MAX
UNITS
500
300
800
400
µA
250
mA
250
mA
95
mA
-7V ≤ VO ≤12V (Note 4)
IOSR
0V ≤ VO ≤ VCC
±6.5
A, B, Y and Z pins, tested using
Human Body Model
ESD Protection
15
kV
SWITCHING CHARACTERISTICS
(VCC = 3.3V ±0.3V, TA = TMIN to TMAX, unless otherwise noted.) (Notes 1, 2)
PARAMETER
Driver Input to Output
SYMBOL
tPLH
tPHL
TYP
MAX
UNITS
10
10
80
80
5
100
100
10
ns
55
55
60
60
13
120
120
5
50
50
80
80
90
90
20
200
200
10
90
90
ns
ns
ns
ns
ns
ns
tZL
tZH
tLZ
CRL = 15pF, S1 closed
40
80
ns
tHZ
CRL = 15pF, S2 closed
40
80
ns
5
10
Mbps
tSKEW
Driver Enable to Output High
Driver Enable to Output Low
Driver Disable Time from Low
Driver Disable Time from High
| tPLH - tPHL | Differential
tZH
tZL
tLZ
tHZ
tSKD
tPLH
tPHL
Receiver Skew | tPLH - tPHL |
Receiver Enable to Output Low
Receiver Enable to Output
High
Receiver Disable Time from
Low
Receiver Disable Time from
High
Maximum Data Rate
MIN
RDIFF = 54
CL1 = CL2 = 100pF
RDIFF = 54, CL1 = CL2 =
100pF
CL= 100pF, S2 closed
CL= 100pF, S1 closed
CL= 15pF, S1 closed
CL= 15pF, S2 closed
RDIFF = 54
RDIFF = 54
CL1 = CL2 = 100pF
CL1 = CL2 = 100pF
CRL = 15pF, S1 closed
CRL = 15pF, S2 closed
Driver Output Skew to Output
Receiver Input to Output
CONDITIONS
fMAX
20
20
2.5
ns
ns
ns
Note 1: All currents into device pins are positive; all currents out of device pins are negative. All voltages are
referenced to device ground unless otherwise specified.
Note 2: All typical specifications are given for VCC=3.3V and TA=+25°C.
Note 3: Supply current specification is valid for loaded transmitters when DE=0V.
Note 4: Applies to peak current.
2012, February, ver. 04
ILX3485
TEST CIRCUITS
Figure 1. Driver VOD and VOC
Figure 2. Driver VOD with Varying Common-Mode
Voltage
Figure 3. Receiver VOH and VOL
Figure 4. Driver Differential Output Delay and Transition Times
2012, February, ver. 04
ILX3485
TEST CIRCUITS (continue)
Figure 5. Driver Propagation Times
Figure 6. Driver Enable and Disable Times (tPZH, tPSH, tPHZ)
Figure 7. Driver Enable and Disable Times (tPZL, tPSL, tPLZ)
2012, February, ver. 04
ILX3485
TEST CIRCUITS (continue)
Figure 8. Receiver Propagation Delay
Figure 9. Receiver Enable and Disable Times
Note 5: The input pulse is supplied by a generator with the following characteristics: PRR = 250kHz, 50%
duty cycle, tr 6.0ns, ZO = 50Ω.
Note 6: CL includes probe and stray capacitance.
2012, February, ver. 04
ILX3485
Function Tables
Transmitting
INPUTS
RE
DE
X
1
X
1
0
0
1
0
DI
1
0
X
X
OUTPUTS X
Z
Y
0
1
1
0
Z
Z
Z
Z
Receiving
INPUTS
RE
DE
A-B
0
0
+0.2V
0
0
-0.2V
0
0
open
1
0
X
OUTPUTS
RO
1
0
1
Z
X-don’t care
Z-high impedance
Typical Information
Figure 10. ILX3485 Typical RS-485 Network
Driver Output Protection
Excessive output current and power dissipation caused by faults or by bus contention are prevented by two
mechanisms. A foldback current limit on the output stage provides immediate protection against short circuits
over the whole common-mode voltage range. In addition, a thermal shutdown circuit forces the driver outputs
into a high-impedance state if the die temperature rises excessively.
Propagation Delay
Skew time is simply the difference between the low-to-high and high-to-low propagation delay. Small
driver/receiver skew times help maintain a symmetrical mark-space ratio (50% duty cycle).
The receiver skew time, |tPRLH - tPRHL|, is under 10ns. The driver skew times are 5ns for the ILX3485.
Typical Applications
ILX3485 transceivers are designed for bidirectional data communications on multipoint bus transmission lines.
Figure 10 shows typical network applications circuits. These parts can also be used as line repeaters, with
cable lengths longer than 4000 feet.
To minimize reflections, the line should be terminated at both ends in its characteristic impedance, and stub
lengths off the main line should be kept as short as possible.
2012, February, ver. 04
TECHNICAL DATA
Package Dimensions
N SUFFIX PLASTIC DIP
(MS – 001BA)
A
Dimension, mm
5
8
B
1
4
F
Symbol
MIN
MAX
A
8.51
10.16
B
6.1
7.11
C
L
C
5.33
D
0.36
0.56
F
1.14
1.78
-T- SEATING
PLANE
N
G
M
K
0.25 (0.010) M
J
H
D
T
NOTES:
1. Dimensions “A”, “B” do not include mold flash or protrusions.
Maximum mold flash or protrusions 0.25 mm (0.010) per side.
G
2.54
H
7.62
J
0°
10°
K
2.92
3.81
L
7.62
8.26
M
0.2
0.36
N
0.38
D SUFFIX SOIC
(MS - 012AA)
Dimension, mm
A
8
5
B
H
1
G
P
4
D
K
MIN
MAX
A
4.8
5
B
3.8
4
C
1.35
1.75
D
0.33
0.51
F
0.4
1.27
R x 45
C
-T-
Symbol
SEATING
PLANE
J
F
0.25 (0.010) M T C M
NOTES:
1. Dimensions A and B do not include mold flash or protrusion.
2. Maximum mold flash or protrusion 0.15 mm (0.006) per side
for A; for B ‑ 0.25 mm (0.010) per side.
M
G
1.27
H
5.72
J
0°
8°
K
0.1
0.25
M
0.19
0.25
P
5.8
6.2
R
0.25
0.5
2012, February, ver. 04