MURF2020CT THRU MURF2060CT R GLASS PASSIVATED SUPER FAST RECTIFIER Reverse Voltage - 200 -600 Volts Forward Current - 20.0Amperes S E M I C O N D U C T O R FEATURES ITO-220AB Plastic package has Underwriters Laboratory Flammability Classification 94V-0 Fast switching for high efficiency 0.190(4.75) 0.165(4.25) 0.145(3.55) Low forward voltage drop 0.128(3.25) DIA 0.130(3.31) Single rectifier construction 0.110(2.81) 0.111(2.83) High surge capability 0.101(2.57) For use in low voltage ,high frequency inverters, 0.174(4.42) 0.165(4.18) free wheeling ,and polarity protection applications 0.410(10.41) JF MURF2020CT High temperature soldering guaranteed:260 C/10 seconds, 0.25"(6.35mm)from case 0.388(9.85) PIN 1 2 3 0.666(16.92) 0.325(8.25) 0.633(16.08) 0.321(8.15) 0.136(3.45) 1.083(27.5) 0.138(3.50) 0.116(2.95) 0.551(14.00) WEEE 2002/96/EC 0.512(13.00) 0.029(0.73) MECHANICAL DATA 0.019(0.47) 0.104(2.64) 0.096(2.44) 0.029(0.73) 0.019(0.47) Case: JEDEC ITO-220AB molded plastic body Terminals: Lead solderable per MIL-STD-750,method 2026 Polarity: As marked. Mounting Position: Any Dimensions in inches and (millimeters) Weight: 0.08ounce, 2.24 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS (Ratings at 25 C ambient temperature unless otherwise specified ,Single phase ,half wave ,resistive or inductive load. For capacitive load,derate by 20%.) Symbols Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage VRRM VRMS VDC MURF 2020CT MURF 2040CT MURF 2060CT 200 400 600 140 280 420 200 400 600 Units Volts Volts Volts Per leg Total device I(AV) 10.0 20.0 Amps Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) IFSM 150.0 150 Amps Maximum average forward rectified current(see Fig.1) Maximum instantaneous forward voltage at 10.0 A(Note 1 ) Maximum instantaneous reverse current at rated DC blocking voltage(Note 1) T A =25 C T A =125 C Maximum Reverse Recovery Time (Note 2) VF IR 0.975 R Operating junction temperature range TJ TSTG 1.3 500 JC 1.5 10 5 Trr Typical thermal resistance (Note 3) Storage temperature range 0.571(14.5) 1.161(29.5) 0.177(4.50) Component in accordance to RoHS 2002/95/EC and 0.610(15.5) Volts uA 35 ns 2.5 C/W -65 to+150 C -65 to+175 C Notes: 1. Pulse test: 300 s pulse width,1% duty cycle 2. Reverse recovery test conditions IF=0.5A,IR=1.0A, Irr=0.5A 3. Thermal resistance from junction to case JINAN JINGHENG ELECTRONICS CO., LTD. 9-36 HTTP://WWW.JINGHENGGROUP.COM RATINGS AND CHARACTERISTIC CURVES MURF2020CT THRU MURF2060CT FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 24 180 20 150 RESISTIVE OR INDUCTVE LOAD 16 PEAK FORWARD SURGE CURRENT(AMPERES) AVERAGE FORWARD CURRENT AMPERES FIG.1-FORWARD CURRENT DERATING CURVE 12 8 4 0 0 20 40 60 80 100 120 120 90 60 30 0 180 150 0.1 1 10 100 LEAD TEMPERATURE ( C) NUMBER OF CYCLES AT 60Hz FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG.4-TYPICAL REVERSE CHARACTERISTICS 20 50 200V TJ=100 C (uA) 400V 10 600V INSTANTANEOUS REVERSE CURRENT INSTANTANEOUS FORWARD CURRENT( AMPERES) 10 PULSE WIDTH=300 S 1% DUTY CYCLE 1 0.1 1 TJ=25 C 0.1 0.01 0.01 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 0.001 0 INSTANTANEOUS FORWARD VOLTAGE (VOLTS) 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE% FIG.6-TYPICAL TRANSIENT THERMAL IMPEDANCE TRANSIENT THERMAL IMPEDANCE, C/ W FIG.5-TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE(pF) 4000 TJ=25 C f=1.0MHZ Vsig=50mVp-p 1000 100 0.1 1 10 100 10 1 0.1 0.01 REVERSE VOLTAGE. VOLTS JINAN JINGHENG ELECTRONICS CO., LTD. 100 0.1 1 10 100 T, PULSE DURATION ,sec. 9-37 HTTP://WWW.JINGHENGGROUP.COM