OPTOWAY XPM

Optoway
XPM-2101WG
1
***********************************************************************************************************************************************************************
XPM-2101WG
(RoHS Compliant)
10Gb/s 1310 nm XFP Extended Multi-Mode Optical Transceiver for 10GbE-LRM Applications
**********************************************************************************************************************************************************************
FEATURES
DESCRIPTION
z
z
z
z
z
z
z
z
XPM-2101WG series extended multi-mode 10G XFP
transceiver is designed for serial optical data
communications such as 10 GBASE-LRM. It supports the
10Gbps transmission on both 50/125 μm and 62.5/125 μm
MMF.
The transceiver consists of two sections: The transmitter
section consists of a directly modulated 1310 nm FP laser,
driver and signal conditioner. The receiver section
incorporates a PIN photodiode integrated with a
trans-impedance preamplifier (TIA) and signal conditioner.
The module is with the XFP 30-pin connector to allow
hot plug capability. Integrated Tx and Rx signal conditioners
provide high jitter-tolerance for full XFI compliance and no
external reference clock required. The internally ac coupled
high speed serial I/O simplifies interfacing to external
circuitry. Only single 3.3V power supply is needed. The
optical output can be disabled by LVTTL logic high-level
input of TX_DIS. Loss of signal (RX_LOS) output is
provided to indicate the loss of an input optical signal of
receiver.
A serial EEPROM in the transceiver allows the user to
access transceiver digital diagnostic monitoring and
configuration data via the 2-wire XFP Management
Interface. This interface uses a single address, A0h, with a
memory map divided into a lower and upper area. Basic
digital diagnostic data is held in the lower area while specific
data is held in a series of tables in the high memory area.
z
z
z
z
z
z
Support 10.3125 Gbps
Complaint with XFP MSA
Compliant to IEEE 802.3aq-2006 10GBASE-LRM
Link Length from 0.5 to 300 m with OM1 MMF
Link Length from 0.5 to 300 m with OM2 MMF
Link Length from 0.5 to 300 m with OM3 MMF
1310 nm Transmitter
2-Wire Interface for Integrated Digital Diagnostic
Monitoring
No reference clock required
Low Power Dissipation < 2.0 W
Only Required +3.3 V Power Supply
RoHS Compliant
0 to 70oC Case Operating Temperature
Duplex LC Connector
APPLICATIONS
z 10G Ethernet at 10.3125Gbps
STANDARD
z Compliant with XFP MSA
z Compliant with IEEE 802.3aq-2006
LASER SAFETY
This multi-mode transceiver is a Class 1 laser product. It
complies with IEC-60825 and FDA 21 CFR 1040.10 and
1040.11. The transceiver must be operated within the
specified temperature and voltage limits. The optical ports
of the module shall be terminated with an optical connector
or with a dust plug.
ORDER INFORMATION
P/No.
XPM-2101WG
Bit Rate
(Gb/s)
10.3125
Distance
(m)
300*
Wavelength
(nm)
1310
Package
Connector
XFP with DMI
LC
Temp
(oC)
0 to 70
RoHS
Compliant
Yes
*: see below table for transmission distance in MM fiber
Multimode Fiber Type**
ISO/IEC 11801:2002
Operating Range
Fiber Type
(m)
0.5 to 300
62.5 μm 160/500
OM1
0.5 to 300
62.5 μm 200/500
OM2
0.5 to 300
50 μm 500/500
OM3
0.5 to 300
50 μm 1500/500***
**: Each fiber type is identified by its core diameter followed by a pair of OFL bandwidth values separated by “/”. The OFL
bandwidths are in MHz-km and are for 850 nm and 1300nm respectively.
***: The OM3 fiber specification includes the 850 nm laser launch bandwidth in addition to the OFL bandwidth.
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw 1/12/2009
V2.0
Optoway
XPM-2101WG
2
***********************************************************************************************************************************************************************
Absolute Maximum Ratings
Parameter
Storage Temperature
Operating Case Temperature
Relative Humidity
Power Supply Voltage
Input Voltage
Symbol
Tstg
Topr
RH
VCC3
---
Min
-40
0
0
0
GND
Max
85
70
85
3.6
Vcc3
Units
o
C
o
C
%
V
V
Min
3.13
Typ
3.3
480
Max
3.47
550
2.0
70
Notes
Non condensing
Recommended Operating Conditions
Parameter
Power Supply Voltage
Power Supply Current (@3.3V)
Power Dissipation
Operating Case Temperature
Data Rate
Symbol
VCC3
ICC3
PD
Topr
0
Units / Notes
V
mA
W
o
C
Gb/s
10.3125
Transmitter Optical Specifications (Topr= 0 to 70oC, Vcc3 = 3.3V ±5%)
Parameter
Average Launch Power
Launch Power in OMA
Peak Launch Power
Extinction Ratio
Output Center Wavelength
Output Spectrum Width
Relative Intensity Noise
Transmitter Waveform and
Dispersion Penalty
Optical Eye Mask
Average Launch Power of OFF
Transmitter
Symbol
Po, Avg
Po, OMA
Min
-6.5
-4.5
Typ
Max
0.5
1.5
3
ER
λc
σλ
RIN
TWDP
3
1260
1310
1350
IEEE 802.3aq-2006, Fig. 68-3
-128
4.7
Compliant with IEEE 802.3ae 10GBASE
-30
Units
dBm
dBm
dBm
dB
nm
nm
dB/Hz
dB
Notes
1
1
RMS (σ)
dBm
1. Output power is power coupled into a MMF.
Receiver Optical Specifications (Topr= 0 to 70oC, Vcc3 = 3.3V ±5%)
Parameter
Stress RX Sensitivity in OMA
Overload in OMA
LOS -- Deasserted
LOS -- Asserted
LOS -- Hysteresis
Wavelength of Operation
Optical Return Loss
Symbol
SS
Min
---
LOSD
LOSA
---20
1
1260
λc
ORL
Typ
--1.5
-------
Max
-6.5
-10
--1360
-12
Units
dBm
dBm
dBm
dBm
dB
nm
dB
Notes
2
Transition: low to high
Transition: high to low
2. Measured with worst ER; BER=1E-12 and PRBS 231-1s.
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw 1/12/2009
V2.0
Optoway
XPM-2101WG
3
***********************************************************************************************************************************************************************
Electrical Characteristics
Parameter
Symbol
High-Speed Signal (CML) Interface Specification
Input Data Rate
Signal Speed Variation from
Normal
Differential Input Impedance
Rin
Differential Data Input Amplitude
Output Data Rate
Signal Speed Variation from
Normal
Differential Output Impedance
Rout
Differential Data Output
Amplitude
Low-Speed Signal (LVTTL) Interface Specification
Input High Voltage
Input Low Voltage
Output High Voltage
Output Low Voltage
Reference Clock (LVPECL) Interface Specification
Min
Typ
Max
Units
±100
Gps
Ppm
10.3125
Ω
100
120
Notes
820
10.3125
±100
mVpp
Gps
Ppm
1, Internally AC coupled
Ω
100
340
850
mVpp
2.0
GND
2.4
GND
Vcc
0.8
Vcc
0.5
V
V
V
V
1, Internally AC coupled
No reference clock
1. The differential input and output amplitudes are per XFP MSA mask at points B’ and C’.
Transceiver Timing Characteristics
Parameter
TX_DIS Assert Time
TX_DIS Negate Time
Time to Initialize
Interrupt Assert Delay
Interrupt Negate Delay
P_Down/PST Assert Delay
P_Down Nagate Delay
Mod_NR Assert Delay
Mod_NR Negate Delay
Mod_Desel Assert Time
Mod_Desel De-Assert Time
P_Down Reset Time
RX_LOS Assert Delay
RX_LOS Negate Delay
Serial ID Clock Rate
Symbol
t_off
t_on
t_init
interrupt_on
interrupt_off
P_Down/RST_on
P_Down/RST_off
Mod_nr_on
Mod_nr_off
T_Mod_Desel
T_Mod_Sel
T_reset
T_Los_on
T_Los_off
fSCL
Min
Typ
Max
10
2
300
200
500
100
300
1
1
2
2
10
0
100
100
400
Units
μs
ms
ms
ms
μs
μs
ms
ms
ms
ms
ms
μs
μs
μs
kHz
Notes
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw 1/12/2009
V2.0
Optoway
XPM-2101WG
4
***********************************************************************************************************************************************************************
MANAGEMENT INTERFACE
The structure of the memory map is shown in Figure 1, which is accessible over a 2-wire serial interface at the 8-bit
address 1010000X (A0h). The normal 256 byte I2C address space is divided into low and upper blocks of 128 Bytes. The
lower block of 128 Bytes is always directly available and is used for the diagnostics and control function. Multiple blocks of
memories are available in the upper 128 Bytes of the address space. These are individually addressed through a table select
Byte which the user enters into a location in the lower address space. Thus, there is a total available address space of 128*256
= 32 Kbytes in this upper memory space. The contents of Table 01h are listed in Table 1 below. Please refer SFF INF-8077i
(Revision 4.5) for detailed information.
Figure 1. 2-wire Serial Digital Diagnostic Memory Map
Data Address
96 ~ 97
98 ~ 99
100 ~ 101
102 ~ 103
104 ~ 105
106 ~ 107
Table 1 Monitoring Specification
Parameter
Accuracy
± 3oC
Temperature
Reserved
Tx Bias
Tx Power
Rx Power
Vcc3
± 10%
± 2dB
± 2dB
± 3%
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw 1/12/2009
V2.0
Optoway
XPM-2101WG
5
***********************************************************************************************************************************************************************
CONNECTION DIAGRAM
Table 3 PIN Description
PIN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Logic
LVTTL-I
LVTTL-O
LVTTL-I
LVTTL-I/O
LVTTL-I/O
LVTTL-O
LVTTL-O
LVTTL-O
CML-O
CML-O
Signal Name
GND
VEE5
Mod_Desel
Interrupt
TX_DIS
VCC5
GND
VCC3
VCC3
SCL
SDA
Mod_Abs
Mod_NR
RX_LOS
GND
GND
RDRD+
GND
VCC2
Description
Note
Module Ground
-5.2V Power Supply (Not required)
Module De-select; When held low allows module to respond to 2-wire serial interface
Interrupt; Indicates presence of an important condition which can be read over the
2wire serial interface
Transmitter Disable; Turns off transmitter laser output
+5V Power Supply (Not required)
Module Ground
+3.3V Power Supply
+3.3V Power Supply
Serial 2-wire interface clock
Serial 2-wire interface data line
Indicates Module is not present. Grounded in the Module
Module Not Ready; Indicating Module Operational Fault
Receiver Loss Of Signal Indicator
Module Ground
Module Ground
Receiver Inverted Data Output
Receiver Non-Inverted Data Output
Module Ground
+1.8V Power Supply (Not required)
1
3
2
3
1
2
2
2
2
2
1
1
1
3
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw 1/12/2009
V2.0
Optoway
XPM-2101WG
6
***********************************************************************************************************************************************************************
21 LVTTL-I
P_Down/RST
22
23
24 PECL-I
VCC2
GND
RefCLK+
25 PECL-I
RefCLK-
26
27
28 CML-I
29 CML-I
30
GND
GND
TDTD+
GND
Power down; When high, requires the module to limit power consumption to 1.5W or
below. 2-Wire serial interface must be functional in the low power mode.
Reset; The falling edge initiates a complete reset of the module including the 2-wire
serial interface, equivalent to a power cycle.
+1.8V Power Supply (Not required)
Module Ground
Reference Clock Non-Inverted Input, AC coupled on the host board. (Not used.
Internally terminated to 50 ohm (100 ohm diff.))
Reference Clock Inverted Input, AC coupled on the host board. (Not used. Internally
terminated to 50 ohm (100 ohm diff.))
Module Ground
Module Ground
Transmitter Inverted Data Input
Transmitter Non-Inverted Data Input
Module Ground
3
1
4
4
1
1
1
1. Module ground pins GND are isolated from the module case and chassis ground within the module.
2. Shall be pulled up with 4.7K-10Kohms to a voltage between 3.15V and 3.45V on the host board.
3. These PINs are open within module.
4. A Reference Clock input is not required. If present, it will be ignored.
MECHANICAL SPECIFICATION (UNITS IN MM)
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw 1/12/2009
V2.0
Optoway
XPM-2101WG
7
***********************************************************************************************************************************************************************
RECOMMENDED POWER CIRCUIT SCHEMATIC
Host Board
VCC5
Optional
Host +5V
4.7μH
0.1μF
VCC3
Host +3.3V
4.7μH
22μF
0.1μF
0.1μF
VCC2
Optional
Host +1.8V
4.7μH
22μF
0.1μF
XFP Connector
22μF
0.1μF
XFP Module
0.1μF
VEE5
Optional
Host -5.2V
4.7μH
0.1μF
22μF
0.1μF
RECOMMENDED INTERFACE CIRCUIT
XFP module
Host Board
SerDat Out+
TD +
Z=50Ω
CML
TD -
SerDat Out-
100Ω
CML
Z=50Ω
SerDat In+
CML
100Ω
RD +
Z=50Ω
SerDat In-
CML
RD -
Z=50Ω
Vcc(+3.3V)
4.7K to 10KΩ
REFCLKP
100Ω
REFCLKN
RX_LOS
INTERRUPT
SDA
VCC(+3.3V)
SCL
MOD_NR
10KΩ
MOD_abs
TX_DIS
GND
MOD_DeSel
P_Down/RST
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw 1/12/2009
V2.0
Optoway
XPM-2101WG
8
***********************************************************************************************************************************************************************
Table 2 Serial ID Memory Contents (Table 01h)
Address
Field
Size
(Byte)
128
1
Identifier
129
130
131~138
139
140
141
142
143
144
145
146
147
1
1
8
1
1
1
1
1
1
1
1
1
Ext. Identifier
Connector type
Transceiver
Encoding
BR-Min
BR-Max
length (SMF)-Km
Length (E-50µm)
Length (50 µm)
Length (62.5 µm)
Length (Copper)
Device Tech
148~163
164
165~167
16
1
3
Vendor name
CDR Support
Vendor OUI
OPTOWAY
CDR supports 10.3125, XFI loop back
168~183
184~185
186~187
16
2
2
XPM-2101WG
ASCII (“31 61” means 1a revision)
1310 nm
188~189
190
191
192~195
2
1
1
4
Vendor PN
Vendor rev
Wavelength
Wavelength
Tolerance
Max Case Temp
CC_BASE
Power Supply
196~211
16
Vendor SN
212~219
8
220
1
Date code
Diagnostic
Monitoring Type
ASCII
ASCII Year (2 Byte), Month (2 Byte), Day (2
Byte)
Name of Filed
Description
XFP
power consumption < 2.0 W, no Ref Colck
required
LC connector
10GBASE-LRM
64B/66B, 8B10B, NRZ
10.3 Gbps
10.3 Gbps
0
300m
300 m
300 m
0m
1300 nm FP Laser, PIN detector
+/- 50nm
70deg
Check sum of Byte 128 -- 190
2.0 Wmax, 1.2W pd_max , 400mA 3.3V
No BER Support, Average Power
Optional Soft TX_DISABLE implemented,
Optional Soft P_down implemented
AUX1 for Vcc3.
Check sum of Byte 192 -- 222
221
1
Enhanced Options
222
1
Aux Monitoring
223
1
CC_EXT
224~255
32
Vendor Specific
Note: Specifications subject to change without notice.
Hex
06
10
07
10 00 00 00 00 00 00 00
D0
67
67
00
96
FF
FF
00
30
4F 50 54 4F 57 41 59 20
20 20 20 20 20 20 20 20
41
00 0E FA
58 50 4D 2D 32 31 30 31
57 47 20 20 20 20 20 20
xx xx
66 58
27 10
46
64 78 04 00
xx xx xx xx xx xx xx xx
xx xx xx xx xx xx xx xx
xx xx xx xx xx xx 20 20
08
60
70
Reserved
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw 1/12/2009
V2.0
Optoway
XPM-2101WG
9
***********************************************************************************************************************************************************************
REVISION HISTORY
Version
1.0
2.0
Subject
Initial datasheet
Corrected the color of level from beige to blue.
Release Date
2008/12/1
2009/12/1
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw 1/12/2009
V2.0