SPH0645LM4H-B

SPH0645LM4H-B
SPH0645LM4H-B
Rev B Datasheet
I2S Output Digital Microphone
The SPH0645LM4H-B is a miniature, low power, bottom port microphone with an I2S digital output.
The solution consists of a proven high performance SiSonic™ acoustic sensor, a serial Analog to
Digital convertor, and an interface to condition the signal into an industry standard 24 bits I2S
format. The I2S interface simplifies the integration in the system and allow direct interconnect to
digital processors, application processors and microcontroller. Saving the need of an external audio
codec, the SPH0645LM4H-B is perfectly suitable for portable applications where size and power
consumption are a constraint.
Product Features:
•
•
•
•
•
•
•
•
•
•
•
•
•
High SNR of 65dB(A)
Low Current of typ. 600µA
I2S Output: Direct attach to µP
Multi modes: standard >1MHz,
600uA / sleep <900kHz, 10uA
Flat Frequency Response
RF Shielded
Supports Dual Microphones
Ultra-Stable Performance
Standard SMD Reflow
Omnidirectional
Zero-Height Mic™
Packaged in SPH 3.50 x 2.65 x 0.98 mm
Typical Applications
•
•
•
No Codec
Needed
SPH0645LM4H-B
Microphone
Filter
knowles.com
Small portable devices: wearables
Set-top boxes: TV, gaming, remote controllers
Smart home devices, Internet of Things,
Connected equipment
I2S
Interface
Application
Processor
I2S
Datasheet SPH0645LM4H-B Rev B
01
Absolute Maximum Ratings
Table 1: Absolute Maximum Ratings
Parameter
Absolute Maximum Rating
Units
VDD,CLK,WS. SEL to Ground
-0.3, +5.0
V
Input Current
±100
mA
Short Circuit to/from DATA
Indefinite to Ground or Vdd
sec
Temperature
-40 to +100
ºC
Stresses exceeding these “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only. Functional operation at these or any
other conditions beyond those indicated under “Acoustic & Electrical Specifications” is not implied. Exposure beyond those indicated under “Acoustic & Electrical Specifications” for extended periods may affect device reliability.
Acoustic & Electrical Specifications
Table 2: TEST CONDITIONS: 25 ±2°C, 55±20% R.H ., VDD =1.8V, fCLOCK = 3.072 MHz with a .1uF decoupling capacitor across Vdd and GND,
unless otherwise indicated
Parameter
Symbol
Conditions
Min.
Directivity
Typ.
Max
Units
Omnidirectional
Polarity
Increasing sound pressure
Output Magnitude Increases
Functional Temperature
Functional with lower performance
-40
100
°C
Operating Temperature
Specifications guaranteed
0
45
°C
VDD
1.62
1.8
3.6
V
Clock Frequency
fCLOCK
2048
3072
4096
kHz
Sleep Clock Frequency
fsleep
900
KHz
-
µA
10
uA
Supply Voltage
Supply Current2,3
Sleep Current
-
IDD
600
IDDSLEEEP
Short Circuit Current
ISC
Grounded DATA pin
2
-
10
mA
Sensitivity
S
94 dB SPL @ 1 kHz
-29
-26
-23
dBFS
Signal to Noise Ratio
SNR
94 dB SPL @ 1 kHz, A-weighted
65
-
dB(A)
Total Harmonic Distortion
THD
94 dB SPL @ 1 kHz, S = Typ.
-
-
1
%
Total Harmonic Distortion
THD
1% THD
94
110
Acoustic Overload
Point
AOP
10% THD @ 1 kHz, S = Typ.
-
120
-
dB SPL
Power Supply Rejection
Ratio
PSRR
200 mVpp sine wave@1kHz
-
80
-
dB
Power Supply Rejection
+Noise
PSR+N
100 mVpp 1/8th duty cycle
rectangular wave@217 Hz,
VDD = 1.8V, A-weighted
Power-up Time4,5
tPOWERUP
VDD ≥ V(min)
knowles.com
Datasheet SPH0645LM4H-B Rev B
dB SPL
-86
-
-
dB(A)
50
ms
02
Microphone Interface Specifications
Table 3: Table 2: TEST CONDITIONS: 25 ±2°C, 55±20% R.H ., VDD =1.8V, fCLOCK = 3.072 MHz with a .1uF decoupling capacitor across Vdd and GND,
unless otherwise indicated
Parameter
Logic Input High
Symbol
Conditions
VIH
Min.
Typ.
Max
Units
0.65xVDD
-
VDD+0.3
V
-
VIL
-0.3
0.35xVDD
V
Low→High Threshold
VL-H
0.55xVDD
0.65xVDD
V
High→Low Threshold
VH-L
0.35xVDD
0.45xVDD
V
VHYST
0.10xVDD
-
0.29xVDD
V
Logic Input Low
Hysteresis Width
Logic Output High
VOH
IOUT = 2 mA
0.7*VDD
-
VDD
V
Logic Output Low
VOL
IOUT = 2 mA
0
-
0.3 * VDD
V
SELECT (high)
VDD -0.2
-
VDD
V
SELECT (low)
GND
-
GND+0.2
V
Select Input
CSELECT
2
pF
Clock Input
CCLK
2
pF
Clock Duty Cycle
Clock Rise/Fall Time
(Input and Output)
TIE Clock Jitter
tEDGE
Measured from 0.1 to 0.9 VDD
TIE
Time Interval Jitter on CLK line
Output Load
CLOAD
Data Format
L
40
50
60
%
-
-
10
ns
2
ns RMS
120
pF
18bit precision, the LSBs are
filled with zeros
24
bits
Figure 1: Hysteresis Diagram
knowles.com
Datasheet SPH0645LM4H-B Rev B
03
Figure 2: Timing Diagram
Parameter
Symbol
Min
Max
Unit
T
244.14
488.28
ns
CLK Pulse Width High
tHC
85.45
ns
CLK Pulse Width Low
tLC
85.45
ns
35% of min.T(=244.14ns)
CLK Period
Note
35% of min.T(=244.14ns)
WS setup time
tSWS
85.45
ns
WS typically synchronized with CLK falling, should be
equal to tBIL
WS hold time
tHWS
85.45
ns
WS typically synchronized with CLK falling, should be
equal to tBIH
Data Delay from
CLK Rising Edge
tDC
Receiver Setup
time
tsr
178.22
ns
Transmitter Hold Time
thtr
7
ns
Clock Rise Time
Measured from VL to
VH
tRC
knowles.com
65.92
3.75
ns
ns
Performance is guaranteed only with SCK edge time
<=3.75ns. For slower edge time, operation is guaranteed
but performance degradation might be expected.
Datasheet SPH0645LM4H-B Rev B
04
Performance Curves
TEST CONDITIONS: 25 ±2°C, 55±20% R.H ., VDD =1.8V, fCLOCK = 3.072 MHz with .1uF decoupling capacitor, unless otherwise indicated
Figure 3: Typical Free Field Response Normalized to 1 kHz
Figure 4: Typical THD vs SPL
knowles.com
Datasheet SPH0645LM4H-B Rev B
05
Application Notes
Hardware Description
Operating Modes
A block diagram of the I2S microphone is shown
in Figure 7. The microphone consists of the
following blocks, the MEMS transducer, the Charge
Pump(red), the Amplifier(yellow), the Sigma Delta
Convertor(green), the Decimator(orange), the Low Pass
Filter(turquoise),and the Tri-state Control (gray).
The I2S Has 2 modes of operation which are
determined by the clock frequency normal and sleep
mode. In addition the I2S microphone can be turned off
by removing power from the VDD pin. Figure 8 shows
the various operating modes.














Figure 5: Block Diagram of the I2S Digital Mic
Operating Description
The I2S microphone operates as follows:
Figure 6: I2S Microphone State Diagram
The Charge Pump(red) boosts VDD to a suitable level to
bias the MEMS transducer.
Active Mode
The MEMs converts an input Sound Pressure Level (SPL)
to a voltage.
The Amplifier (yellow) buffers the output voltage of
the MEMs and provides sufficient drive to provide the
Sigma Delta Convertor a stable signal.
The Sigma Delta Convertor (green) converts the
buffered analog signal into a serial Pulse Density
Modulated (PDM) signal.
The Decimator (orange) down-converts the PDM signal
by a factor of 64, it also converts the single bit PDM
signal to Multi-bit Pulse Code Modulated (PCM) signal.
The Low Pass Filter (turquoise), removes any remaining
high frequency components in the PCM signal and
improves the bandwidth of the Decimator output.
The Tri-state Control (gray) uses the state of the WS and
SELECT inputs to determine if the DATA pin is driven
or tri-stated. This allows 2 microphones to operate on
a single I2S port. When SELECT =HIGH the DATA pin
drives the SDIN bus when WS=HIGH otherwise DATA=
tri-state. When SELECT =LOW the DATA pin drives the
SDIN bus when WS=LOW otherwise DATA= tri-state.
knowles.com
When Vdd is applied the microphone senses the
CLOCK line, if the frequency is greater than 900KHz ,
the microphone enters the normal mode of operation.
In this mode the I2S Master must provide the CLK and
WS signals as the microphone is an I2S slave device.
Sleep Mode
When Vdd is applied the microphone senses the
CLOCK line, if the frequency is less than 900KHz or
completely off , the microphone enters the sleep mode
of operation. In this mode the microphone tri-states the
DATA pin and turns off internal circuits to reduce power
consumption.
Powered Down Mode
This mode is entered by removing Vdd from the
microphone. The presence of CLK, WS and SELECT,
have no effect on this mode and the DATA pin is tristated. The Powered Down Mic will not interfere with
other devices on the I2S bus.
Datasheet SPH0645LM4H-B Rev B
06
Interface Description
The SPH0645LM4H microphone operates as an I2S
slave. The master must provide the BCLK and WS
signals. The Over Sampling Rate is fixed at 64 therefore
the WS signal must be BCLK/64 and synchronized
to the BCLK. Clock frequencies from 2.048Mhz to
4.096MHz are supported so sampling rates from 32KHz
to 64KHz can be had by changing the clock frequency.
The SEL pin determines when the microphone drives
the Data pin. When SEL=H the Data pin is driven when
the WS=H, otherwise it is tri-stated (high impedance).
When operating a single microphone on an I2S bus,
a pull down resistor (100K Ohms) should be placed
from the Data pin to ground to insure the bus
capacitance is discharged
The Data Format is I2S, 24 bit, 2’s compliment, MSB
first. The Data Precision is 18 bits, unused bits are zeros.























Figure 7: Timing Diagram
System Connections
Figure 8: System (Stereo) Connections
Notes:
1. Decoupling capacitors (C33, C35) mounted as close as possible are required for optimum SNR.
2. RF filter Capacitors (C32,C34) in the range of 20-200pF may be needed depending on RF environment.
3. If both decoupling and RF filter capacitors are used, the RF filter capacitors should be the closest to the microphone.
4. Detailed information on acoustic, mechanical, and system integration can be found in the latest SiSonic™ Design Guide application note.
knowles.com
Datasheet SPH0645LM4H-B Rev B
07
System Connection’s Cont’d
Figure 8, Shows how two I2S Microphones can be connected on a single I2S bus. R41–R44 are included to either
dampen or terminate their respective traces. If the traces are electrically long then they should be controlled impedance traces with impedance in the 50-120 Ohm range. Electrically long traces are when the length of the trace
(in inches) is => 2 times the rise/fall time (in nS).
Even if the traces are not electrically long, R41-R44 can be used as dampening resistors (27-51 Ohms) to improve
signal integrity by reducing overshoots and ringing caused by stray inductance and capacitance. In either case,
R41-R44 are placed as close as possible to the device that drives the trace (signal source). The decoupling capacitors (C32-33, C34-35) are most effective if the trace inductance between the capacitor and microphone is minimized. This can be accomplished by using short wide traces. If a ground plane is used under the microphone then
connect the capacitor ground pads directly to the plane with vias without any trace used.
I2S Timing And Port Configuration Guidelines
•
•
•
•
•
BCLK period must be in the range shown in Figure 2
WS must be synchronized(changing) on the falling edge of BCLK
WS must be BCLK/64
The Hold Time (see Figure 2) must be greater than the Hold Time of the Receiver
The mode must be I2S with MSB delayed 1 BCLK cycle after WS changes
Layout Guidelines
Good layout techniques are required for optimal noise, distortion, and signal integrity. Suggested layout guidelines
are described in Knowles’ Multi-Mode Digital Microphone SPH0641LM4H-1 Application Note.
knowles.com
Datasheet SPH0645LM4H-B Rev B
08
Mechanical Specifications
Item
Nominal
Tolerance
Units
Length (L)
3.50
±0.10
mm
Width (W)
2.65
±0.10
mm
Height (H)
0.98
±0.10
mm
Acoustic Port Diameter (AP)
0.325
±0.05
mm
Pin #
Pin Name
Type
Description
1
WS
Digital Input
Word Strobe
2
SELECT
Digital Input
Select L/R
3
GND
Power
Ground
4
BCLK
Digital Input
Bit Clock
5
VDD
Power
Power Supply
6
Data Out
Digital Output
Digital Data Output
Example Land Pattern
Notes:
knowles.com
Example Solder Stencil Pattern
Pick Area only extends to 0.25 mm of any edge or hole unless otherwise specified.
Dimensions are in millimeters unless otherwise specified.
Tolerance is ±0.15mm unless otherwise specified
Detailed information on AP size considerations can be found in the latest SiSonic™ Design Guide application note.
Further optimizations based on application should be performed.
Datasheet SPH0645LM4H-B Rev B
09
Packaging & Marking Detail
Model Number
Suffix
Reel Diameter
Quantity Per Reel
SPH0645LM4H-B
8
13”
5900
Alpha Character A:
“S”: Knowles SiSonic™ Production
“E”: Knowles Engineering Samples
“P”: Knowles Prototype Samples
“12345678”:
Unique Job Identification Number for product traceability
Notes:
Pin 1
Dimensions are in millimeters unless otherwise specified.
Vacuum pickup only in the pick area indicated in Mechanical Specifications.
Tape & reel per EIA-481.
Labels applied directly to reel and external package.
Shelf life: Twelve (12) months when devices are to be stored in factory supplied, unopened ESD moisture sensitive bag under maximum environmental
conditions of 30°C, 70% R.H.
knowles.com
Datasheet SPH0645LM4H-B Rev B
10
Recommended Reflow Profile
tP
TP
Ramp-up
TL
tL
TSMAX
tS Preheat
TSMIN
Ramp-down
25°C
Time 25°C to Peak
Profile Feature
Time
PH-Free
Average Ramp-up rate (TSMAX to TP)
3°C/second max.
Preheat
•
Temperature Min (TSMIN)
•
Temperature Max (TSMAX)
•
Time (TSMIN to TSMAX) (tS)
150°C
200°C
60–180 seconds
Time maintained above:
•
Temperature (TL)
•
Time (tL)
217°C
60–150 seconds
Peak Temperature (TP)
260°C
Time within 5°C of actual Peak Temperature (tP)
20–40 seconds
Ramp-down rate (TP to TSMAX)
6°C/second max
Time 25°C to Peak Temperature
Notes:
8 minutes max
Based on IPC/JDEC J-STD-020 Revision C.
All temperatures refer to topside of the package, measured on the package body surface
Additional Notes
(A)
(B)
(C)
MSL (moisture sensitivity level) Class 1.
Maximum of 3 reflow cycles is recommended.
In order to minimize device damage:
• Do not board wash or clean after the reflow process.
• Do not brush board with or without solvents after the reflow process.
• Do not directly expose to ultrasonic processing, welding, or cleaning.
• Do not insert any object in port hole of device at any time.
• Do not apply over 30 psi of air pressure into the port hole.
• Do not pull a vacuum over port hole of the microphone.
• Do not apply a vacuum when repacking into sealed bags at a rate faster than 0.5 atm/sec.
knowles.com
Datasheet SPH0645LM4H-B Rev B
11
Materials Statement
Meets the requirements of the European RoHS directive 2011/65/EC as amended.
Meets the requirements of the industry standard IEC 61249-2-21:2003 for halogenated substances and Knowles
Green Materials Standards Policy section on Halogen-Free.
Ozone depleting substances are not used in the product or the processes used to make the product, including
compounds listed in Annex A, B, and C of the “Montreal Protocol on Substances That Deplete the Ozone Layer.”
Reliability Specifications
Test
Description
Reflow
5 reflow cycles with peak temperature of +260°C
High Temperature Storage
+105°C environment for 1,000 hours (IEC 68-2-2 Test Ba)
Low Temperature Storage
-40°C environment for 1,000 hours (IEC 68-2-1 Test Aa)
High Temperature Bias
+105°C environment while under bias for 1,000 hours (IEC 68-2-2 Test Ba)
Low Temperature Bias
-40°C environment while under bias for 1,000 hours (IEC 68-2-1 Test Aa)
Temperature/Humidity Bias
+85°C/85% R.H. environment while under bias for 1,000 hours (JESD22-A101A-B)
Thermal Shock
100 cycles of air-air thermal shock from -40°C to +125°C with 15 minute soaks (IEC 68-2-4)
Tumble Test
300 Random Drops of Test Box on to Steel Base from 1.0m, 10 Tumbles/Minute
Vibration
16 minutes in each X, Y, Z axis from 20 to 2,000 Hz with peak acceleration of 20 G
(MIL 883E, Method 2007.2,A)
Mechanical Shock
3 pulses of 10,000 G in each of the X, Y, and Z directions (IEC 68-2-27 Test Ea)
ESD-HBM
3 discharges of ±2kV direct contact to I/O pins (MIL 883E, Method 3015.7)
ESD-LID/GND
3 discharges of ±8kV direct contact to lid while unit is grounded (IEC 61000-4-2)
ESD-MM
3 discharges of ±200V direct contact to IO pins (ESD STM5.2)
Notes:
Microphones must meet all acoustic and electrical specifications before and after reliability testing.
After 3 reflow cycles, the sensitivity of the microphones shall not deviate more than 1 dB from its initial value.
Specification Revisions
Revision
Specification Changes
Date
A
ECR 15-201
6/9/2015
B
Corrected Timing Diagram ECR#15-251
7/17/2015
Information contained herein is subject to change without notice. It may be used by a party at their own discretion
and risk. We do not guarantee any results or assume any liability in connection with its use. This publication is not
to be taken as a license to operate under any existing patents.
Model/Reference Number:
Datasheet SPH0645LM4H-B Rev B
© Copyright 2015 Knowles
Phone: (630) 250-5100
Fax: (630) 250-0575
[email protected]
Knowles
1151 Maplewood Drive
Itasca, Illinois 60143