Recessed Downlight Can Fixtures /120VAC & 277VAC

Recessed Downlight Can Fixtures/120VAC & 277VAC
for High-Efficacy GU24-Base PAR30 & PAR38 LED Bulbs
RL6120A / RL75120A / RL6277A / RL75277A
VERTICAL RETROFIT SYSTEMS FOR LED FLOOD LIGHTING
Operates on 120VAC or 277VAC — 6” or 7.5” Aperture Sizes — 120V Kits Dimmable — Made in the USA
■■
6” diameter aperture
LED light bulb not included
RETRO SYSTEM
Easily installs into existing downlight
mounting frame, J-box and mounting
hardware
■■
Consists of precisely designed reflector,
GU24 socket, flex, cap and wire
attached to J-box
■■
For use in non-IC-rated ceilings only
■■
Made in the USA from post-industrial
and consumer recycled content
S P E C I F I C AT I O N S
ELECTRICAL
For use in damp locations
7.5” diameter aperture
LED light bulb not included
RETRO SYSTEM
INPUT VOLTAGE
APERTURE
■■
Kit Warranty
3 Years
RL6120A
120VAC
6 inch
■■
ETLCM classified for LED retrofits
Wiring
For 120V and 277V retrofits
RL6277A
277VAC
6 inch
RL75120A
120VAC
7.5 inch
Lamp Type
277VAC
7.5 inch
■■
Designed for GU24 based PAR30
& PAR38 LED lamps only
RL75277A
REFLECTOR
Reflector has 30° cutoff for general
illumination
PART NUMBER
SIZE CHART (inches)
APERTURE
ID
6
7.5
HEIGHT
OT OD
5.8
7
8.75
8.5
7.5
8.5
9.25
10
000000
00000
8.75”
222.25mm
Ø5.8”
Ø147.3mm
Ø7.0”
Ø177.8mm
A-Clear Alzak® Haze reflector provides
durable and anti-iridescent finish, with
self-flanged trim
■■
Vent slots provide convection cooling
■■
DIMMING
Use LED lamps indicated for 120V LED
dimming only
■■
Compatible with most LED phasecontrol dimmers (Lutron C•LTM category
models in Diva®, Skylark Contour TM,
Luméa®, Ariadni® & Hi-Lume LED
Maestro® series recommended for best
results)
Available for the GU24 Recessed
Can Light Fixtures (NOT INCLUDED)
Long-Life, Energy-Efficient Drop-In Halogen Replacement
UL-Listed LED Bulbs in 2-Pin/GU24 Utility-Compliant Base
Clear Lens – 3000K Warm White — Premium SMD LEDs
REFLECTOR MOUNTING CLIPS
9.25”
234.95mm
Accessory mounting clips are not required
for all installations
FOR 7.5” CAN
Consumes
15 Watts
MC4–Bottom mount
ISO
PAR30GU-12W-001M Series
PAR30GU-12W-120AMD Series
Operates on 110-120VAC
MADE IN
© 2012 LEDtronics, Inc.
PAR38GU-15W-001M Series
PAR38GU-15W-120AMD Series
Operates on 90-290VAC
MC6–Bottom mount
9001:2008
CERTIFIED by DNV
USA
Consumes
12 Watts
Operates on 90-290VAC
Operates on 110-120VAC
23105 Kashiwa Court, Torrance, CA 90505
Phone: (800) 579.4875 / (310) 534.1505
Fax: (310) 534.1424
E-mail: [email protected]
Website: http://www.ledtronics.com
Check LEDTRONICS.COM for latest data.
Printed material may be outdated.
Ø8.5”
Ø215.9mm
FOR 6” CAN
MC1–Top mount
MC2–Top mount
Ø7.5”
Ø190.5mm
An optional
LEDtronics
PAR30GU
Series bulb
in the Alzak®
Haze Reflector
BULBS SOLD
SEPARATELY
■ACCESSORIES
000000
00000
0000000
000
000000
00000
00
RL75120A
RL75277A
■■
LOG 372 / Rev 04-2012
0000000
000
000000
00000
00
RL6120A
RL6277A
OD
w w w. LE D t r o n i c s .co m
■FEATURES
INSTALLATION INSTRUCTIONS
WARNING:
Page 2
Risk of fire or electric shock. Install this kit only in a fixture that has the construction
features shown in these installation instruction drawings.
w w w. LE D t r o n i c s .co m
Pull down existing reflector from
plaster frame
Carefully cut socket wires and detach
power feed from socket
Attach power feed to new socket cap
J-box and wire-up
Connect socket J-box to existing J-box
for support, use box connector
Note:
The existing fixture being
retro-fitted may require other
clip options. If any problem is
encountered with the MC2 clip,
study the following clip options
to determine the best clip.
Snap-on MC2 spring clips to mounting
frame
Attach new reflector to lamp holder by
keyhole slots
Slide reflector into frame, insert proper
lamp and check operation
Clip snaps onto mounting frame screw
holes
MC2 clip can be screwed into side of
frame
Clip mounts under mounting frame
collar
© 2012 LEDtronics, Inc.
Three clips for plaster frames with
thick die-cast aluminum collars. Clips
slide under frame.