1.6X0.8mm SMD CHIP LED LAMP Part Number: AP1608SURCK Hyper Red Features Description z 1.6mmX0.8mm SMT LED, 1.1mm thickness. The Hyper Red source color devices are made with AlGaInP z Low power consumption. on GaAs substrate Light Emitting Diode. z Wide viewing angle. z Ideal for backlight and indicator. z Various colors and lens types available. z Package: 2000pcs / reel. z Moisture sensitivity level : level 3. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.1(0.004") unless otherwise noted. 3.The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4.The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAB2720 REV NO: V.14A DATE: OCT/25/2013 PAGE: 1 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.N.Huang ERP: 1203000076 Selection Guide Part No. Dice AP1608SURCK Iv (mcd) [2] @ 20mA Lens Type Hyper Red (AlGaInP) Min. Typ. 120 230 *40 *80 Water Clear Viewing Angle [1] 2θ1/2 120° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. *Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Hyper Red λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 645 nm IF=20mA Hyper Red 630 nm IF=20mA Spectral Line Half-width Hyper Red 28 nm IF=20mA C Capacitance Hyper Red 35 pF VF=0V;f=1MHz VF [2] Forward Voltage Hyper Red 1.95 2.5 V IF=20mA IR Reverse Current Hyper Red 10 uA VR=5V Notes: 1.Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. Absolute Maximum Ratings at TA=25°C Parameter Hyper Red Units Power dissipation 75 mW DC Forward Current 30 mA Peak Forward Current [1] 185 mA 5 V Reverse Voltage Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAB2720 REV NO: V.14A DATE: OCT/25/2013 PAGE: 2 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.N.Huang ERP: 1203000076 Hyper Red AP1608SURCK SPEC NO: DSAB2720 REV NO: V.14A DATE: OCT/25/2013 PAGE: 3 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.N.Huang ERP: 1203000076 AP1608SURCK Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAB2720 REV NO: V.14A DATE: OCT/25/2013 PAGE: 4 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.N.Huang ERP: 1203000076 PACKING & LABEL SPECIFICATIONS AP1608SURCK Terms and conditions for the usage of this document 1.The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2.The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3.When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4.The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5.The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6.All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAB2720 REV NO: V.14A DATE: OCT/25/2013 PAGE: 5 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.N.Huang ERP: 1203000076