3.0mmx1.0mm RIGHT ANGLE SMD CHIP LED LAMP Part Number: APA3010SURCK-GX Hyper Red Features Description z 3.0mmx2.0mmx1.0mm right angle SMD LED, 1.0mm The Hyper Red source color devices are made with AlGaInP on GaAs substrate Light Emitting Diode. thickness. z Low power consumption. z Wide viewing angle. z Ideal for back light and indicator. z Package : 2000pcs / reel. z Moisture sensitivity level : level 3. z Tinned pads for improved solderability. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.15(0.006") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4.The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAL3675 APPROVED: Wynec REV NO: V.7A CHECKED: Allen Liu DATE: AUG/20/2015 PAGE: 1 OF 5 DRAWN: M.Liu ERP: 1203000643 Selection Guide Part No. Emitting Color (Material) Lens Type Hyper Red (AlGaInP) APA3010SURCK-GX Water Clear Iv (mcd) [2] @ 20mA Viewing Angle [1] Min. Typ. 120 220 *40 *80 2θ1/2 120° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity / luminous Flux: +/-15%. * Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Emitting Color Typ. λpeak Peak Wavelength Hyper Red λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 645 nm IF=20mA Hyper Red 630 nm IF=20mA Spectral Line Half-width Hyper Red 28 nm IF=20mA C Capacitance Hyper Red 35 pF VF=0V;f=1MHz VF [2] Forward Voltage Hyper Red 1.95 2.5 V IF=20mA IR Reverse Current Hyper Red 10 uA VR=5V Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Values Units Power dissipation 75 mW DC Forward Current 30 mA Peak Forward Current [1] 185 mA 5 V Reverse Voltage Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAL3675 APPROVED: Wynec REV NO: V.7A CHECKED: Allen Liu DATE: AUG/20/2015 PAGE: 2 OF 5 DRAWN: M.Liu ERP: 1203000643 Hyper Red SPEC NO: DSAL3675 APPROVED: Wynec APA3010SURCK-GX REV NO: V.7A CHECKED: Allen Liu DATE: AUG/20/2015 PAGE: 3 OF 5 DRAWN: M.Liu ERP: 1203000643 APA3010SURCK-GX Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAL3675 APPROVED: Wynec REV NO: V.7A CHECKED: Allen Liu DATE: AUG/20/2015 PAGE: 4 OF 5 DRAWN: M.Liu ERP: 1203000643 PACKING & LABEL SPECIFICATIONS APA3010SURCK-GX Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAL3675 APPROVED: Wynec REV NO: V.7A CHECKED: Allen Liu DATE: AUG/20/2015 PAGE: 5 OF 5 DRAWN: M.Liu ERP: 1203000643