10 SEGMENT BAR GRAPH ARRAY Part Number: DC10GWA Green Features Description z Suitable for level indicators. The Green source color devices are made with Gallium z Low current operation. Phosphide Green Light Emitting Diode. z Excellent on/off contrast. z End stackable. z Mechanically rugged. z Standard : gray face, white segment. z RoHS compliant. Package Dimensions& Internal Circuit Diagram Notes: 1. All dimensions are in millimeters (inches), Tolerance is ±0.25(0.01")unless otherwise noted. 2. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. SPEC NO: DSAD1429 REV NO: V.9A DATE: NOV/18/2013 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED: Joe Lee DRAWN: Y.Liu ERP: 1331000017 Selection Guide Part No. Dice DC10GWA Lens Type Green (GaP) Iv (ucd) [1] @ 10mA Min. Typ. 5600 12000 *1400 *4000 White Diffused Description 10 Segments Bar graph-Display Note: 1. Luminous intensity/ luminous Flux: +/-15%. *Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Green λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 565 nm IF=20mA Green 568 nm IF=20mA Spectral Line Half-width Green 30 nm IF=20mA C Capacitance Green 15 pF VF=0V;f=1MHz VF [2] Forward Voltage Green 2.2 2.5 V IF=20mA IR Reverse Current Green 10 uA VR=5V Notes: 1.Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. Absolute Maximum Ratings at TA=25°C Parameter Green Units 62.5 mW DC Forward Current 25 mA Peak Forward Current [1] 140 mA 5 V Power dissipation Reverse Voltage Operating / Storage Temperature Lead Solder Temperature[2] -40°C To +85°C 260°C For 3-5 Seconds Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. 2mm below package base. SPEC NO: DSAD1429 REV NO: V.9A DATE: NOV/18/2013 PAGE: 2 OF 6 APPROVED: WYNEC CHECKED: Joe Lee DRAWN: Y.Liu ERP: 1331000017 Green DC10GWA SPEC NO: DSAD1429 REV NO: V.9A DATE: NOV/18/2013 PAGE: 3 OF 6 APPROVED: WYNEC CHECKED: Joe Lee DRAWN: Y.Liu ERP: 1331000017 PACKING & LABEL SPECIFICATIONS DC10GWA Terms and conditions for the usage of this document 1.The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2.The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3.When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4.The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5.The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6.All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAD1429 REV NO: V.9A DATE: NOV/18/2013 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Joe Lee DRAWN: Y.Liu ERP: 1331000017 SPEC NO: DSAD1429 REV NO: V.9A DATE: NOV/18/2013 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Joe Lee DRAWN: Y.Liu ERP: 1331000017 SPEC NO: DSAD1429 REV NO: V.9A DATE: NOV/18/2013 PAGE: 6 OF 6 APPROVED: WYNEC CHECKED: Joe Lee DRAWN: Y.Liu ERP: 1331000017