T-1 3/4 (5mm) BLINKING LED LAMP ATTENTION Part Number: WP56BID High Efficiency Red OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Descriptions z T-1 3/4 package. z The High Efficiency Red source color devices are made with Gallium Arsenide Phosphide on Gallium Phosphide z With built-in blinking IC. z Operation voltage from 3.5V to 14V. z Blinking frequency from 3.0Hz to 1.5Hz. Orange Light Emitting Diode. z Electrostatic discharge and power surge could damage the LEDs. z RoHS compliant. z It is recommended to use a wrist band or antielectrostatic glove when handling the LEDs. z All devices, equipments and machineries must be electrically grounded. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. 4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. SPEC NO: DSAE9871 REV NO: V.6A DATE: MAR/16/2015 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101009279 Selection Guide Part No. Dice High Efficiency Red (GaAsP/GaP) WP56BID Iv (mcd) V= 9V Lens Type Red Diffused Viewing Angle [1] Min. Typ. 18 40 *12 *25 2θ1/2 60° Note: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. *Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Min. Typ. λpeak Peak Wavelength High Efficiency Red 627 nm λD Dominant Wavelength High Efficiency Red 617 nm Δλ1/2 Spectral Line Half-width High Efficiency Red 45 nm IF Forward Current High Efficiency Red 22 mA Min:VF=3.5V Typ:VF=5V ISON Supply Current High Efficiency Red 8 mA VF=3.5V ISON Supply Current High Efficiency Red 44 mA VF=14V f Blink Frequency High Efficiency Red Hz VF=3.5V~14V 8 Max. 1.5 3 Units Test Conditions Notes: 1.Wavelength value is traceable to the CIE127-2007 compliant national standards. 2.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter High Efficiency Red Units Power dissipation 310 mW Forward Voltage 14 V Reverse Voltage 0.5 V Operating Temperature -40°C To +70°C Storage Temperature -40°C To +85°C Lead Solder Temperature [1] 260°C For 3 Seconds Lead Solder Temperature [2] 260°C For 5 Seconds Notes: 1. 2mm below package base. 2. 5mm below package base. SPEC NO: DSAE9871 REV NO: V.6A DATE: MAR/16/2015 PAGE: 2 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101009279 High Efficiency Red WP56BID SPEC NO: DSAE9871 REV NO: V.6A DATE: MAR/16/2015 PAGE: 3 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101009279 PACKING & LABEL SPECIFICATIONS WP56BID Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAE9871 REV NO: V.6A DATE: MAR/16/2015 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101009279 SPEC NO: DSAE9871 REV NO: V.6A DATE: MAR/16/2015 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101009279 SPEC NO: DSAE9871 REV NO: V.6A DATE: MAR/16/2015 PAGE: 6 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101009279