APT1608F3C - Kingbright

1.6x0.8mm INFRARED EMITTING DIODE
Part Number: APT1608F3C
Features
Description
z 1.6mmX0.8mm SMT LED, 0.75mm thickness.
F3 Made with Gallium Arsenide Infrared Emitting diodes.
z Mechanically and spectrally matched to phototransistor.
z Package: 2000pcs / reel .
z Moisture sensitivity level : level 3.
z RoHS compliant.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.1(0.004") unless otherwise noted.
3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
4. The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAH3781
REV NO: V.6A
DATE: MAR/18/2015
PAGE: 1 OF 5
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1203001654
Selection Guide
Part No.
APT1608F3C
Dice
Lens Type
F3 (GaAs)
Water Clear
Po (mW/sr) [2]
@ 20mA
Min.
Typ.
1.2
3
*0.8
*2
Viewing
Angle [1]
2θ1/2
120°
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Radiant Intensity / luminous flux: +/-15%.
*Radiant Intensity value is traceable to the CIE127-2007 compliant national standards.
Electrical / Optical Characteristics at TA=25°C
Parameter
P/N
Symbol
Typ.
Max.
Units
Test Conditions
Forward Voltage [1]
F3
VF
1.2
1.6
V
IF=20mA
Reverse Current
F3
IR
10
uA
VR = 5V
Capacitance
F3
C
90
pF
VF=0V;f=1MHz
Peak Spectral Wavelength
F3
λP
940
nm
IF=20mA
Spectral Bandwidth
F3
Δλ1/2
50
nm
IF=20mA
Notes:
1. Forward Voltage: +/-0.1V.
2. Wavelength value is traceable to the CIE127-2007 compliant national standards.
3. Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or
premature failure.
Absolute Maximum Ratings at TA=25°C
Parameter
Symbol
F3
Units
Power dissipation
PD
80
mW
DC Forward Current
IF
50
mA
Peak Forward Current [1]
iFS
1.2
A
Reverse Voltage
VR
5
V
Operating Temperature
TA
-40 To +85
°C
TSTG
-40 To +85
°C
Storage Temperature
Note:
1. 1/100 Duty Cycle, 10μs Pulse Width.
SPEC NO: DSAH3781
REV NO: V.6A
DATE: MAR/18/2015
PAGE: 2 OF 5
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1203001654
APT1608F3C
SPEC NO: DSAH3781
REV NO: V.6A
DATE: MAR/18/2015
PAGE: 3 OF 5
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1203001654
APT1608F3C
Reflow soldering is recommended and the soldering profile is shown below.
Other soldering methods are not recommended as they might cause damage to the product.
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
Reel Dimension
Tape Specifications
(Units : mm)
SPEC NO: DSAH3781
REV NO: V.6A
DATE: MAR/18/2015
PAGE: 4 OF 5
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1203001654
PACKING & LABEL SPECIFICATIONS
APT1608F3C
Terms and conditions for the usage of this document
1. The information included in this document reflects representative usage scenarios and is intended for technical reference only.
2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without
notice. Before production usage customer should refer to the latest datasheet for the updated specifications.
3. When using the products referenced in this document, please make sure the product is being operated within the environmental
and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible
for any subsequent issues.
4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has
special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with
Kingbright representative for further assistance.
5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright.
6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes
SPEC NO: DSAH3781
REV NO: V.6A
DATE: MAR/18/2015
PAGE: 5 OF 5
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1203001654