3.2x1.6mm INFRARED EMITTING DIODE Part Number: AP3216F3C Features Description z 3.2mmx1.6mm SMT LED, 1.1mm thickness. F3 Made with Gallium Arsenide Infrared Emitting diodes. z Mechanically and spectrally matched to the phototransistor. z Wide viewing angle. z Package : 2000pcs / reel. z Moisture sensitivity level : level 3. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.2(0.0079") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4.The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAD1358 REV NO: V.8A DATE: MAR/24/2015 PAGE: 1 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203000342 Selection Guide Part No. AP3216F3C Dice Lens Type F3 (GaAs) Water Clear Po (mW/sr) [2] @ 20mA Min. Typ. 1.2 3 *0.8 *2 Viewing Angle [1] 2θ1/2 120° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Radiant Intensity/ luminous flux: +/-15%. *Radiant intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Parameter P/N Symbol Typ. Max. Units Test Conditions Forward Voltage [1] F3 VF 1.2 1.6 V IF=20mA Reverse Current F3 IR 10 uA VR = 5V Capacitance F3 C 90 pF VF=0V;f=1MHz Peak Spectral Wavelength F3 λP 940 nm IF=20mA Spectral Bandwidth F3 Δλ1/2 50 nm IF=20mA Note: 1.Forward Voltage: +/-0.1V. 2.Wavelength value is traceable to the CIE127-2007 compliant national standards. 3.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Symbol F3 Units Power dissipation PD 80 mW DC Forward Current IF 50 mA Peak Forward Current [1] iFS 1.2 A Reverse Voltage VR 5 V Operating Temperature TA -40 To +85 °C TSTG -40 To +85 °C Storage Temperature Note: 1. 1/100 Duty Cycle, 10μs Pulse Width. SPEC NO: DSAD1358 REV NO: V.8A DATE: MAR/24/2015 PAGE: 2 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203000342 AP3216F3C SPEC NO: DSAD1358 REV NO: V.8A DATE: MAR/24/2015 PAGE: 3 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203000342 AP3216F3C Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Specifications (Units : mm) SPEC NO: DSAD1358 REV NO: V.8A DATE: MAR/24/2015 PAGE: 4 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203000342 PACKING & LABEL SPECIFICATIONS AP3216F3C Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAD1358 REV NO: V.8A DATE: MAR/24/2015 PAGE: 5 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203000342