MX25UM51245G

ADVANCED INFORMATION
MX25UM51245G
MX25UM51245G
1.8V 512M-BIT [x 1/x 8]
CMOS MXSMIO® (SERIAL MULTI I/O)
FLASH MEMORY
Key Features
• Protocol Support - Single I/O and Octa I/O
• Support DTR (Double Transfer Rate) Mode
• Support clock frequency up to 200MHz
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
Contents
1. FEATURES............................................................................................................................................................... 5
2. GENERAL DESCRIPTION...................................................................................................................................... 7
Table 1. Operating Frequency Comparison.................................................................................................7
3. PIN CONFIGURATIONS .......................................................................................................................................... 8
Table 2. PIN DESCRIPTION........................................................................................................................8
4. BLOCK DIAGRAM.................................................................................................................................................... 9
5. MEMORY ORGANIZATION.................................................................................................................................... 10
6. DATA PROTECTION............................................................................................................................................... 11
6-1.
Block lock protection................................................................................................................................. 12
Table 3. Protected Area Sizes....................................................................................................................12
6-2. Additional 8K-bit secured OTP ................................................................................................................. 13
Table 4. Secured OTP Definition................................................................................................................13
7. DEVICE OPERATION............................................................................................................................................. 14
8. COMMAND SET..................................................................................................................................................... 16
8-1.
SPI Command Set.................................................................................................................................... 16
Table 5. Read/Write Array Commands (SPI)..............................................................................................16
Table 6. Setting Commands (SPI)..............................................................................................................17
Table 7. Reset Commands (SPI)................................................................................................................17
Table 8. Register Commands (SPI)............................................................................................................18
8-2. OPI Command Set.................................................................................................................................... 19
Table 9. Read/Write Array Commands (OPI).............................................................................................19
Table 10. Setting Commands (OPI)...........................................................................................................20
Table 11. Reset Commands (OPI).............................................................................................................20
Table 12. Register Commands (OPI).........................................................................................................21
9. REGISTER DESCRIPTION..................................................................................................................................... 23
9-1.
9-2.
9-3.
9-4.
Status Register......................................................................................................................................... 23
Configuration Register.............................................................................................................................. 24
Configuration Register 2........................................................................................................................... 25
Security Register...................................................................................................................................... 27
Table 13. Security Register Definition........................................................................................................27
10. COMMAND DESCRIPTION.................................................................................................................................. 28
10-1. Write Enable (WREN)............................................................................................................................... 28
10-2. Write Disable (WRDI)................................................................................................................................ 29
10-3. Read Identification (RDID)........................................................................................................................ 30
Table 14. ID Definitions .............................................................................................................................30
10-4. Read Status Register (RDSR).................................................................................................................. 31
10-5. Read Configuration Register (RDCR)....................................................................................................... 34
10-6. Write Status Register (WRSR) / Write Configuration Register (WRCR)................................................... 35
10-7. Read Configuration Register 2 (RDCR2).................................................................................................. 38
10-8.Write Configuration Register 2 (WRCR2).................................................................................................. 39
P/N: PM2183
2
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
10-9. Read Security Register (RDSCUR).......................................................................................................... 40
10-10.Write Security Register (WRSCUR).......................................................................................................... 41
10-11. Read Data Bytes (READ)......................................................................................................................... 42
10-12.Read Data Bytes at Higher Speed (FAST_READ)................................................................................... 43
10-13.OCTA Read Mode (8READ)..................................................................................................................... 44
10-14.OCTA DTR Read Mode (8DTRD)............................................................................................................. 45
10-15.Preamble Bit............................................................................................................................................. 46
10-16.Burst Read................................................................................................................................................ 47
10-17.Fast Boot.................................................................................................................................................. 48
10-18.Sector Erase (SE)..................................................................................................................................... 53
10-19.Block Erase (BE)...................................................................................................................................... 54
10-20.Chip Erase (CE)........................................................................................................................................ 55
10-21.Page Program (PP).................................................................................................................................. 56
10-22.Deep Power-down (DP)............................................................................................................................ 58
10-23.Release from Deep Power-down (RDP)................................................................................................... 59
10-24.Enter Secured OTP (ENSO)..................................................................................................................... 60
10-25.Exit Secured OTP (EXSO)........................................................................................................................ 60
10-26.Write Protection Selection (WPSEL)......................................................................................................... 61
10-27.Individual Sector Protection...................................................................................................................... 62
10-28.Program/Erase Suspend/Resume............................................................................................................ 72
10-29.Erase Suspend......................................................................................................................................... 72
10-30.Program Suspend..................................................................................................................................... 72
10-31.Write-Resume........................................................................................................................................... 74
10-32.No Operation (NOP)................................................................................................................................. 74
10-33.Software Reset (Reset-Enable (RSTEN) and Reset (RST)).................................................................... 74
11. Serial Flash Discoverable Parameter (SFDP)................................................................................................... 76
11-1. Read SFDP Mode (RDSFDP)................................................................................................................... 76
Table 15. Signature and Parameter Identification Data Values (TBD).......................................................77
12. RESET.................................................................................................................................................................. 78
Table 16. Reset Timing-(Standby)..............................................................................................................78
Table 17. Reset Timing-(Other Operation).................................................................................................78
13. POWER-ON STATE.............................................................................................................................................. 79
14. ELECTRICAL SPECIFICATIONS......................................................................................................................... 80
Table 18. ABSOLUTE MAXIMUM RATINGS.............................................................................................80
Table 19. CAPACITANCE TA = 25°C, f = 1.0 MHz.....................................................................................80
Table 20. DC CHARACTERISTICS...........................................................................................................82
Table 21. AC CHARACTERISTICS............................................................................................................83
15. OPERATING CONDITIONS.................................................................................................................................. 85
Table 22. Power-Up/Down Voltage and Timing .........................................................................................87
15-1. INITIAL DELIVERY STATE....................................................................................................................... 87
16. ERASE AND PROGRAMMING PERFORMANCE............................................................................................... 88
17. DATA RETENTION............................................................................................................................................... 88
P/N: PM2183
3
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
18. LATCH-UP CHARACTERISTICS......................................................................................................................... 88
19. ORDERING INFORMATION................................................................................................................................. 89
20. PART NAME DESCRIPTION................................................................................................................................ 90
21. PACKAGE INFORMATION................................................................................................................................... 91
22. REVISION HISTORY ............................................................................................................................................ 92
P/N: PM2183
4
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
1.8V 512M-BIT [x 1/x 8] CMOS MXSMIO® (SERIAL MULTI I/O)
FLASH MEMORY
1. FEATURES
GENERAL
• Supports Serial Peripheral Interface -- Mode 0
• Single Power Supply Operation
- 1.7 to 2.0 volt for read, erase, and program operations
• 512Mb: 536,870,912 x 1 bit structure or 67,108,846 x 8 bits (Octa I/O mode) structure
• Protocol Support
- Single I/O and Octa I/O
- Support DTR (Double Transfer Rate) Mode
• Latch-up protected to 100mA from -1V to Vcc +1V
• Low Vcc write inhibit is from 1.0V to 1.4V
• Fast frequency support
- Support clock frequency up to
- Single I/O mode: 133MHz
- Octa I/O mode: 200MHz
- Configurable dummy cycle number for OPI read operation
• Octa Peripheral Interface (OPI) available
• Equal Sectors with 4K byte each, or Equal Blocks with 64K byte each
- Any Block can be erased individually
• Programming :
- 256byte page buffer
- Octa Input/Output page program to enhance program performance
• Typical 100,000 erase/program cycles
• 20 years data retention
SOFTWARE FEATURES
• Input Data Format
- SPI: 1-byte command code
- OPI: 2-byte command code
• Advanced Security Features
- Block lock protection
The BP0-BP3 and T/B status bits define the size of the area to be protected against program and erase
instructions
- Individual Sector Protection (Solid Protect)
• Additional 8K bit security OTP
- Features unique identifier
- Factory locked identifiable, and customer lockable
• Command Reset
• Program/Erase Suspend and Resume operation
• Electronic Identification
- JEDEC 1-byte manufacturer ID and 2-byte device ID
• Support Serial Flash Discoverable Parameters (SFDP) mode
P/N: PM2183
5
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
HARDWARE FEATURES
• SCLK Input
- Serial clock input
• SIO0 - SIO7
- Serial Data Input or Serial Data Output
• DQS
- Data strobe signal
• RESET#
- Hardware Reset pin
• PACKAGE
-24-Ball BGA (5x5 ball array)
-All devices are RoHS Compliant and Halogen Free.
P/N: PM2183
6
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
2. GENERAL DESCRIPTION
MX25UM51245G is 512Mb bits serial Flash memory, which is configured as 67,108,864 x 8 internally.
MX25UM51245G feature a serial peripheral interface and software protocol allowing operation on a simple 3-wire
bus while it is in single I/O mode. The three bus signals are a clock input (SCLK), a serial data input (SI), and a
serial data output (SO). Serial access to the device is enabled by CS# input.
The MX25UM51245G MXSMIO® (Serial Multi I/O) provides sequential read operation on whole chip.
After program/erase command is issued, auto program/erase algorithms which program/erase and verify the
specified page or sector/block locations will be executed. Program command is executed on byte basis, or page (256
bytes) basis, or word basis. Erase command is executed on sector (4K-byte), or block (64K-byte), or whole chip
basis.
To provide user with ease of interface, a status register is included to indicate the status of the chip. The status read
command can be issued to detect completion status of a program or erase operation via WIP bit.
When the device is not in operation and CS# is high, it is put in standby mode.
The MX25UM51245G utilizes Macronix's proprietary memory cell, which reliably stores memory contents even after
100,000 program and erase cycles.
Table 1. Operating Frequency Comparison
Numbers of Dummy Cycle
6
8
10
12
14
16
18
20
Octa I/O STR (MHz)
66
84
104
104
133
166
166
200*
Octa I/O DTR (MHz)
66
84
104
104
133
166
166
200*
Notes: * means default status
P/N: PM2183
7
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
3. PIN CONFIGURATIONS
24-BALL BGA (5x5 ball array)
1
Table 2. PIN DESCRIPTION
2
3
4
NC
NC
RESET#
DNU
NC
SCLK
GND
VCC
NC
VSSQ
CS#
DQS
SIO2
NC
SYMBOL
CS#
SCLK
RESET#
DQS
5
A
B
C
D
E
VCCQ
SIO1
SIO0
SIO3
SIO4
SIO7
SIO6
SIO5
VCCQ
VSSQ
SI/SIO0
SO/SIO1
SIO2-SIO7
VCC
VCCQ
GND
VSSQ
DNU
NC
DESCRIPTION
Chip Select
Clock Input
Hardware Reset Pin Active lowNote 1
Data Strobe Signal
Serial Data Input (for 1 x I/O)/ Serial
Data Input & Output (for 8 x I/O read
mode)
Serial Data Output (for 1 x I/O)/ Serial
Data Input & Output (for 8 x I/O read
mode)
Serial Data Input & Output (for 8 x I/O
read mode)
1.8V Power Supply
1.8V Buffer Power Supply
Ground
IO Ground Supply
Do not use
No Connection
Notes:
1. RESET# pin has internal pull up.
P/N: PM2183
8
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
4. BLOCK DIAGRAM
X-Decoder
Address
Generator
SI/SIO0
SO/SIO1
SIO2
SIO3
SIO4
SIO5
SIO6
SIO7
RESET#
CS#
DQS
SCLK
Memory Array
Y-Decoder
Data
Register
Sense
Amplifier
SRAM
Buffer
Mode
Logic
State
Machine
HV
Generator
Clock Generator
Output
Buffer
P/N: PM2183
9
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
5. MEMORY ORGANIZATION
Address Range
3FFF000h
…
…
16383
3FF8FFFh
3FF7000h
3FF7FFFh
3FF0000h
3FF0FFFh
16367
3FEF000h
3FEFFFFh
…
16360
3FE8000h
3FE8FFFh
16359
3FE7000h
3FE7FFFh
…
3FE0000h
3FE0FFFh
16351
3FDF000h
3FDFFFFh
…
16344
3FD8000h
3FD8FFFh
16343
3FD7000h
3FD7FFFh
16336
…
…
…
16352
…
1021
…
…
…
16368
…
1022
…
3FF8000h
16375
…
16376
…
1023
3FFFFFFh
…
Sector
…
Block(64K-byte)
3FD0000h
3FD0FFFh
∼
…
0028FFFh
027000h
0027FFFh
0020FFFh
001F000h
001FFFFh
…
0018000h
0018FFFh
23
0017000h
0017FFFh
P/N: PM2183
…
…
24
000FFFFh
0008000h
0008FFFh
7
0007000h
0007FFFh
…
8
…
…
0010FFFh
000F000h
…
0010000h
15
…
16
…
0
…
0020000h
31
…
32
…
1
…
0028000h
39
…
40
…
2
002FFFFh
…
002F000h
…
47
0
0000000h
0000FFFh
10
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
6. DATA PROTECTION
During power transition, there may be some false system level signals which result in inadvertent erasure or
programming. The device is designed to protect itself from these accidental write cycles.
The state machine will be reset as standby mode automatically during power up. In addition, the control register
architecture of the device constrains that the memory contents can only be changed after specific command
sequences have completed successfully.
In the following, there are several features to protect the system from the accidental write cycles during VCC powerup and power-down or from system noise.
• Valid command length (SPI Mode) or command/command# combination (OPI Mode) will be check.
• Write Enable (WREN) command: WREN command is required to set the Write Enable Latch bit (WEL) before
other command to change data.
• Deep Power Down Mode: By entering deep power down mode, the flash device also is under protected from
writing all commands except Release from deep power down mode command (RDP), and softreset command.
P/N: PM2183
11
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
6-1. Block lock protection
- The Software Protected Mode (SPM) use (BP3, BP2, BP1, BP0 and T/B) bits to allow part of memory to be
protected as read only. The protected area definition is shown as Table 3 Protected Area Sizes, the protected
areas are more flexible which may protect various area by setting value of BP0-BP3 bits.
Table 3. Protected Area Sizes
Protected Area Sizes (T/B bit = 0)
Status bit
BP3
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
BP2
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
BP1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
BP0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Protect Level
512Mb
0 (none)
1 (1 block, protected block 1023rd)
2 (2 blocks, protected block 1022nd~1023rd)
3 (4 blocks, protected block 1020th~1023rd)
4 (8 blocks, protected block 1016th~1023rd)
5 (16 blocks, protected block 1008th~1023rd)
6 (32 blocks, protected block 992nd~1023rd)
7 (64 blocks, protected block 960th~1023rd)
8 (128 blocks, protected block 896th~1023rd)
9 (256 blocks, protected block 768th~1023rd)
10 (512 blocks, protected block 512nd~1023rd)
11 (1024 blocks, protected all)
12 (1024 blocks, protected all)
13 (1024 blocks, protected all)
14 (1024 blocks, protected all)
15 (1024 blocks, protected all)
Protected Area Sizes (T/B bit = 1)
Status bit
BP3
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
P/N: PM2183
BP2
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
BP1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
Protect Level
BP0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
512Mb
0 (none)
1 (1 block, protected block 0th)
2 (2 blocks, protected block 0th~1th)
3 (4 blocks, protected block 0th~3rd)
4 (8 blocks, protected block 0th~7th)
5 (16 blocks, protected block 0th~15th)
6 (32 blocks, protected block 0th~31st)
7 (64 blocks, protected block 0th~63rd)
8 (128 blocks, protected block 0th~127th)
9 (256 blocks, protected block 0th~255th)
10 (512 blocks, protected block 0th~511st)
11 (1024 blocks, protected all)
12 (1024 blocks, protected all)
13 (1024 blocks, protected all)
14 (1024 blocks, protected all)
15 (1024 blocks, protected all)
12
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
6-2. Additional 8K-bit secured OTP
The secured OTP for unique identifier: to provide 8K-bit one-time program area for setting device unique serial
number. Which may be set by factory or system customer.
- Security register bit 0 indicates whether the chip is locked by factory or not.
- To program the 8K-bit secured OTP by entering secured OTP mode (with Enter Security OTP command), and
going through normal program procedure, and then exiting secured OTP mode by writing Exit Security OTP
command.
- Customer may lock-down the customer lockable secured OTP by writing WRSCUR(write security register)
command to set customer lock-down bit1 as "1". Please refer to "Table 13. Security Register Definition" for
security register bit definition and "Table 4. Secured OTP Definition" for address range definition.
- Note: Once lock-down by factory or customer, the corresponding range cannot be changed any more. While in
secured OTP mode, array access is not allowed.
Table 4. Secured OTP Definition
Address range
Size
Lock-down
xxx000~xxx1FF
4096-bit
Determined by Factory
xxx200~xxx3FF
4096-bit
Determined by Customer
P/N: PM2183
13
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
7. DEVICE OPERATION
1. Before a command is issued, status register should be checked to ensure device is ready for the intended
operation.
2. When incorrect command# sequence is inputted to this device, this device becomes standby mode and keeps
the standby mode until next CS# falling edge. In standby mode, SO pin of this device should be High-Z.
3. When correct command# sequence is inputted to this device, this device becomes active mode and keeps the
active mode until next CS# rising edge.
4. When device under STR mode, input data is latched on the rising edge of Serial Clock (SCLK) and data shifts
out on the falling edge of SCLK. When device under DTR mode, input data is latched on the both rising and
falling edge of Serial Clock (SCLK) and data shifts out on both rising and falling edge of SCLK.
5.While a Write Status Register, Program or Erase operation is in progress, access to the memory array is
neglected and not affect the current operation of Write Status Register, Program, Erase.
Figure 1. Input Timing (STR mode)
tSHSL
CS#
tCHSL
tSLCH
tCHSH
tSHCH
SCLK
tDVCH
tCHCL
tCHDX
tCLCH
LSB
MSB
SIO
Figure 2. Input Timing (DTR mode)
tSHSL
CS#
tCHSL
tSLCH
tSHCH
tCLSH
SCLK
tDVCH
tCHDX
SIO
P/N: PM2183
tCHCL
tCLDX
tDVCL
MSB
tCLCH
LSB
14
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
Figure 3. Output Timing (STR mode)
CS#
tCH
SCLK
tCLQV
tCLQX
tCL
tCLQV
tSHQZ
tCLQX
LSB
SIO
Figure 4. Output Timing (DTR mode)
SCLK
tCHQV
tCLQV
DQS
tQSQV
tQSQV
tQXQS
tQXQS
SIO[7:0]
P/N: PM2183
15
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
8. COMMAND SET
8-1. SPI Command Set
Table 5. Read/Write Array Commands (SPI)
Command
(byte)
1st byte
READ
(normal read)
13 (hex)
FAST READ
(fast read data)
0C (hex)
2nd byte
ADD1
ADD1
RDID
(read identification)
9F (hex)
RDSFDP
5A (hex)
ADD1
3rd byte
ADD2
ADD2
ADD2
4th byte
ADD3
ADD3
ADD3
5th byte
ADD4
6th byte
ADD4
Dummy(8)
Data Cycles
Action
n bytes read out until n bytes read out until outputs JEDEC ID:
CS# goes high
CS# goes high
1-byte Manufacturer
ID & 2-byte Device ID
Command
(byte)
1st byte
PP
(page program)
12 (hex)
SE
(sector erase)
21 (hex)
BE
(block erase 64KB)
DC (hex)
2nd byte
ADD1
ADD1
ADD1
3rd byte
ADD2
ADD2
ADD2
4th byte
ADD3
ADD3
ADD3
5th byte
ADD4
ADD4
ADD4
Read SFDP
mode
CE
(chip erase)
60 or C7 (hex)
6th byte
Data Cycles
Action
P/N: PM2183
1-256
to program the
selected page
to erase the selected to erase the selected to erase whole chip
sector
block
16
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
Table 6. Setting Commands (SPI)
Command
(byte)
WREN
(write enable)
WRDI
(write disable)
1st byte
06 (hex)
04 (hex)
PGM/ERS Suspend PGM/ERS Resume
(Suspends Program/ (Resumes Program/
Erase)
Erase)
B0 (hex)
30 (hex)
DP (Deep power
down)
B9 (hex)
2nd byte
3rd byte
4th byte
5th byte
Data Cycles
sets the (WEL) write
resets the (WEL)
enable latch bit
write enable latch bit
enters deep power
down mode
Action
Command
(byte)
1st byte
RDP (Release from
deep power down)
AB (hex)
SBL
(Set Burst Length)
C0 (hex)
ENSO
(enter secured OTP)
B1 (hex)
EXSO
(exit secured OTP)
C1 (hex)
to enter the 8K-bit
secured OTP mode
to exit the 8K-bit
secured OTP mode
2nd byte
3rd byte
4th byte
5th byte
Data Cycles
Action
1
release from deep
power down mode
to set Burst length
Table 7. Reset Commands (SPI)
Command
(byte)
1st byte
NOP
(No Operation)
00 (hex)
RSTEN
(Reset Enable)
66 (hex)(Note 2)
RST
(Reset Memory)
99 (hex)(Note 2)
2nd byte
3rd byte
4th byte
5th byte
Action
P/N: PM2183
17
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
Table 8. Register Commands (SPI)
Command
(byte)
RDSR
(read status
register)
1st byte
05 (hex)
RDCR
(read
configuration
register)
15 (hex)
WRSR
(write status/
configuration
register)
01 (hex)
RDCR 2
(read
configuration
register 2)
71 (hex)
WRCR2
(Write
configuration
register 2 )
72 (hex)
ADD1
ADD1
2nd byte
RDFBR
WRFBR
(read fast boot (write fast boot
register)
register)
16 (hex)
17 (hex)
3rd byte
ADD2
ADD2
4th byte
ADD3
ADD3
ADD4
ADD4
1
1
1-4
4
WRLR
(write Lock
register)
RDLR
(read Lock
register)
WRSPB
(SPB bit
program)
4
ESSPB
(all SPB bit
erase)
0
2C (hex)
2D (hex)
E3 (hex)
E4 (hex)
5th byte
Data Cycles
Action
Command
(byte)
1
1
to read out the to read out the
values of the values of the
status register configuration
register
ESFBR
(erase fast
boot register)
1-2
to write new
values of the
status/
configuration
register
RDSCUR
WRSCUR
(read security (write security
register)
register)
Address Bytes
1st byte
18 (hex)
2B (hex)
2F (hex)
2nd byte
ADD1
3rd byte
ADD2
4th byte
ADD3
5th byte
ADD4
Data Cycles
1
1
to read value to set the lockof security
down bit as
register
"1" (once lockdown, cannot
be updated)
Action
WRDPB
(write DPB
register)
4
RDDPB
(read DPB
register)
4
WPSEL
(Write Protect
Selection)
Address Bytes
RDSPB
(read SPB
status)
4
GBLK
(gang block
lock)
0
GBULK
(gang block
unlock)
0
1st byte
E2 (hex)
E1 (hex)
E0 (hex)
68 (hex)
7E (hex)
98 (hex)
2nd byte
ADD1
ADD1
ADD1
3rd byte
ADD2
ADD2
ADD2
4th byte
ADD3
ADD3
ADD3
5th byte
ADD4
ADD4
ADD4
Data Cycles
1
1
1
to enter and
enable individal
block protect
mode
whole chip
write protect
whole chip
unprotect
Command
(byte)
Action
Note 1: It is not recommended to adopt any other code/address not in the command definition table, which will potentially enter
the hidden mode.
Note 2: Before executing RST command, RSTEN command must be executed. If there is any other command to interfere, the
reset operation will be disabled.
Note 3: The number in parentheses after "ADD" or "Data" stands for how many clock cycles it has. For example, "Data(8)" represents there are 8 clock cycles for the data in.
P/N: PM2183
18
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
8-2. OPI Command Set
Table 9. Read/Write Array Commands (OPI)
Command
(byte)
1st byte
8READ
(Octa IO Read)
EC (hex)
8DTRD
(Octa IO DT Read)
EE (hex)
RDID
(read identification)
9F (hex)
2nd byte
13 (hex)
11 (hex)
60 (hex)
A5 (hex)
3rd byte
ADD1
ADD1
00h
ADD1
4th byte
ADD2
ADD2
00h
ADD2
5th byte
ADD3
ADD3
00h
ADD3
6th byte
ADD4
7th byte
Dummy(Note 4)
Data Cycles
Octa I/O STR read
Action
ADD4
(Note 6)
00h
Dummy(Note 4)
RDSFDP
5A (hex)
ADD4
Dummy(20)
3 (Note 8)
Octa I/O DTR read
outputs JEDEC ID:
1-byte Manufacturer
ID & 2-byte Device ID
Read SFDP
mode
Command
(byte)
1st byte
PP
(page program)
12 (hex)
SE
(sector erase)
21 (hex)
BE
(block erase 64KB)
DC (hex)
CE
(chip erase)
60 or C7 (hex)
2nd byte
ED (hex)
DE (hex)
23 (hex)
9F or 38 (hex)
3rd byte
ADD1
ADD1
ADD1
4th byte
ADD2
ADD2
ADD2
5th byte
ADD3
ADD3
ADD3
6th byte
ADD4(Note 6)
ADD4
ADD4
7th byte
Data Cycles
Action
P/N: PM2183
1-256
to program the
selected page
to erase the selected to erase the selected to erase whole chip
sector
block
19
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
Table 10. Setting Commands (OPI)
Command
(byte)
WREN
(write enable)
PGM/ERS Suspend PGM/ERS Resume
(Suspends Program/ (Resumes Program/
Erase)
Erase)
B0 (hex)
30 (hex)
WRDI
(write disable)
1st byte
06 (hex)
04 (hex)
2nd byte
F9 (hex)
FB (hex)
4F (hex)
CF (hex)
DP (Deep power
down)
B9 (hex)
46 (hex)
3rd byte
4th byte
5th byte
6th byte
7th byte
sets the (WEL) write
resets the (WEL)
enable latch bit
write enable latch bit
enters deep power
down mode
Data Cycles
Command
(byte)
1st byte
RDP (Release from
deep power down)
AB (hex)
SBL
(Set Burst Length)
C0 (hex)
ENSO
(enter secured OTP)
B1 (hex)
EXSO
(exit secured OTP)
C1 (hex)
2nd byte
54 (hex)
3F (hex)
4E (hex)
3E (hex)
to enter the 8K-bit
secured OTP mode
to exit the 8K-bit
secured OTP mode
3rd byte
00h
4th byte
00h
5th byte
00h
6th byte
00h
7th byte
1
Data Cycles
release from deep
power down mode
to set Burst length
Table 11. Reset Commands (OPI)
Command
(byte)
1st byte
NOP
(No Operation)
00 (hex)
RSTEN
(Reset Enable)
66 (hex)(Note 2)
RST
(Reset Memory)
99 (hex)(Note 2)
2nd byte
FF (hex)
99 (hex)
66 (hex)
3rd byte
4th byte
5th byte
6th byte
Data Cycles
P/N: PM2183
20
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
Table 12. Register Commands (OPI)
Command
(byte)
RDSR
(read status
register)
RDCR
WRCR (write
(read
WRSR (write
configuration
configuration status register)
register)
register)
15 (hex)
01 (hex)
01 (hex)
RDCR2
(read
configuration
register 2)
71 (hex)
WRCR2
(Write
configuration
register 2 )
72 (hex)
RDFBR
(read fast boot
register)
1st byte
05 (hex)
2nd byte
FA (hex)
EA (hex)
FE (hex)
FE (hex)
8E (hex)
8D (hex)
E9 (hex)
3rd byte
00h
00h
00h
00h
ADD1(Note 7)
ADD1(Note 7)
00h
(Note 7)
(Note 7)
00h
00h
00h
00h
00h
00h
00h
00h
ADD3
ADD3
6th byte
00h
01h
00h
01h
ADD4(Note 7)
ADD4(Note 7)
7th byte
Data bytes
Action
Command
(byte)
1st byte
Dummy
(Note 5)
Dummy
(Note 5)
Dummy
1
1
1
1
to read out the to read out the to write new
to write new
values of the values of the values of the values of the
status register configuration status register configuration
register
register
WRFBR
ESFBR
(write fast boot (erase fast
register)
boot register)
17 (hex)
18 (hex)
E7 (hex)
ADD2
ADD2
4th byte
5th byte
RDSCUR
WRSCUR
(read security (write security
register)
register)
2B (hex)
2F (hex)
(Note 5)
00h
Dummy(Note 5)
1
1
1-4(Note 8)
WRLR
(write Lock
register)
2C (hex)
RDLR
(read Lock
register)
2D (hex)
WRSPB
(SPB bit
program)
E3 (hex)
D3 (hex)
D2 (hex)
1C (hex)
E8 (hex)
3rd byte
00h
00h
00h
00h
ADD1
4th byte
00h
00h
00h
00h
ADD2
5th byte
00h
00h
00h
00h
ADD3
6th byte
00h
00h
00h
00h
Dummy(Note 5)
ADD4
1
1
Dummy
7th byte
D0 (hex)
00h
00h
2nd byte
Data bytes
D4 (hex)
16 (hex)
(Note 5)
4
to read value to set the lockof security
down bit as
register
"1" (once lockdown, cannot
be updated)
Action
RDSPB
(read SPB
status)
WRDPB
(write DPB
register)
RDDPB
(read DPB
register)
E4 (hex)
E2 (hex)
E1 (hex)
E0 (hex)
WPSEL
(Write
Protection
Selection)
68 (hex)
1B (hex)
1D (hex)
1E (hex)
1F (hex)
97 (hex)
Command
(byte)
ESSPB
(all SPB bit
erase)
1st byte
2nd byte
3rd byte
ADD1
ADD1
ADD1
4th byte
ADD2
ADD2
ADD2
5th byte
ADD3
ADD3
ADD3
6th byte
ADD4
ADD4
ADD4
7th byte
Dummy(Note 4)
Data bytes
1
GBULK
(gang block
unlock)
7E (hex)
98 (hex)
81 (hex)
67 (hex)
Dummy(Note 4)
1
1
to enter and
whole chip
enable individal write protect
block protect
mode
Action
P/N: PM2183
GBLK
(gang block
lock)
21
whole chip
unprotect
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
Note 1: It is not recommended to adopt any other code/address not in the command definition table, which will potentially enter
the hidden mode.
Note 2: Before executing RST command, RSTEN command must be executed. If there is any other command to interfere, the
reset operation will be disabled.
Note 3: The number in parentheses after "ADD" or "Data" stands for how many clock cycles it has. For example, "Data(8)" represents there are 8 clock cycles for the data in.
Note 4: See dummy cycle and frequency table.
Note 5: 4 dummy cycles in both STR/DTR.
Note 6: The starting address must be even byte (A0 must be 0) in DTR OPI mode.
Note 7: The address data must be 00h.
Note 8: Data byte are always output in STR.
P/N: PM2183
22
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
9. REGISTER DESCRIPTION
9-1. Status Register
The definition of the status register bits is as below:
WIP bit. The Write in Progress (WIP) bit, a volatile bit, indicates whether the device is busy in program/erase/write
status register progress. When WIP bit sets to 1, which means the device is busy in program/erase/write status
register progress. When WIP bit sets to 0, which means the device is not in progress of program/erase/write status
register cycle.
WEL bit. The Write Enable Latch (WEL) bit, a volatile bit, indicates whether the device is set to internal write enable
latch. When WEL bit sets to 1, which means the internal write enable latch is set, the device can accept program/
erase/write status register instruction. When WEL bit sets to 0, which means no internal write enable latch; the
device will not accept program/erase/write status register instruction. The program/erase command will be ignored
if it is applied to a protected memory area. To ensure both WIP bit & WEL bit are both set to 0 and available for next
program/erase/operations, WIP bit needs to be confirm to be 0 before polling WEL bit. After WIP bit confirmed, WEL
bit needs to be confirm to be 0.
BP3, BP2, BP1, BP0 bits. The Block Protect (BP3, BP2, BP1, BP0) bits, non-volatile bits, indicate the protected area
(as defined in Table 3) of the device to against the program/erase instruction without hardware protection mode being
set. To write the Block Protect (BP3, BP2, BP1, BP0) bits requires the Write Status Register (WRSR) instruction to
be executed. Those bits define the protected area of the memory to against Page Program (PP), Sector Erase (SE),
Block Erase (BE) and Chip Erase (CE) instructions (only if Block Protect bits (BP3:BP0) set to 0, the CE instruction
can be executed). The BP3, BP2, BP1, BP0 bits are "0" as default. Which is un-protected.
Status Register
bit7
Reserved
bit6
Reserved
bit5
BP3
(level of
protected
block)
bit4
BP2
(level of
protected
block)
bit3
BP1
(level of
protected
block)
bit2
BP0
(level of
protected
block)
Reserved
Reserved
(note 1)
(note 1)
(note 1)
(note 1)
Reserved
Reserved
Non-volatile
bit
Non-volatile
bit
Non-volatile
bit
Non-volatile
bit
bit1
bit0
WEL
WIP
(write enable
(write in
latch)
progress bit)
1=write
1=write
enable
operation
0=not write 0=not in write
enable
operation
volatile bit
volatile bit
Note 1: see the Table 3 "Protected Area Size".
P/N: PM2183
23
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
9-2. Configuration Register
The Configuration Register is able to change the default status of Flash memory. Flash memory will be configured
after the CR bit is set.
ODS bit
The output driver strength (ODS2, ODS1, ODS0) bits are volatile bits, which indicate the output driver level (as
defined in "Output Driver Strength Table") of the device. The Output Driver Strength is defaulted as 30 Ohms when
delivered from factory. To write the ODS bits requires the Write Status Register (WRSR) instruction to be executed.
TB bit
The Top/Bottom (TB) bit is a non-volatile bit. The Top/Bottom (TB) bit is used to configure the Block Protect area by
BP bit (BP3, BP2, BP1, BP0), starting from TOP or Bottom of the memory array. The TB bit is defaulted as “0”, which
means Top area protect. When it is set as “1”, the protect area will change to Bottom area of the memory device. To
write the TB bits requires the Write Status Register (WRSR) instruction to be executed.
PBE bit
The Preamble Bit Enable (PBE) bit is a volatile bit. It is used to enable or disable the preamble bit data pattern
output on dummy cycles. The PBE bit is defaulted as “0”, which means preamble bit is disabled. When it is set as “1”,
the preamble bit will be enabled, and inputted into dummy cycles. To write the PBE bits requires the Write Status
Register (WRSR) instruction to be executed.
Configuration Register
bit7
bit6
bit5
Reserved
Reserved
Reserved
x
x
x
x
x
x
bit4
bit3
bit2
bit1
bit0
PBE
TB
ODS 2
ODS 1
ODS 0
(Preamble bit (top/bottom (output driver (output driver (output driver
Enable)
selected)
strength)
strength)
strength)
0=Top area
0=Disable
protect
1=Bottom
(Note 1)
(Note 1)
(Note 1)
1=Enable
area protect
(Default=0)
volatile bit
OTP
volatile bit
volatile bit
volatile bit
Note 1: see "Output Driver Strength Table"
Output Driver Strength Table
ODS2
0
0
0
0
1
1
1
1
P/N: PM2183
ODS1
0
0
1
1
0
0
1
1
ODS0
0
1
0
1
0
1
0
1
Description
150 Ohms
75 Ohms
50 Ohms
38 Ohms
30 Ohms
25 Ohms
22 Ohms
20 Ohms (Default)
24
Note
Impedance at VCC/2
(Typical)
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
9-3. Configuration Register 2
Address
0x0000
0x0200
0x0300
Bit
Bit 7-2
Symbol
x
Description
Reserved
Bit 1
DOPI
DTR OPI Enable
Bit 0
SOPI
STR OPI Enable
Bit 7
x
Bit 6-4
DQSSKW
Bit 3-2
x
Bit 1
DOS
DQS on STR mode
Bit 0
DQSPRC
DTR DQS pre-cycle
Bit 7-3
x
Bit 2-0
DC
Bit 7
Bit 6-5
Bit 4
Bit 3-1
x
Reserved
Reserved
x
Reserved
SIO to DQS Skew
Reserved
Reserved
Dummy cycle
Reserved
Reserved
Reserved
0x0500
Reserved
Preamable pattern
Bit 0
PPTSEL
selection
Bit 7-4
x
Reserved
Bit 3
x
Reserved
Bit 2
x
Reserved
0x40000000
Enable DOPI after power
Bit 1 DEFDOPI#
on reset
Enable SOPI after power
Bit 0 DEFSOPI#
on reset
P/N: PM2183
25
Define
Reserved
0= DTR OPI disable
1= DTR OPI enable
0= STR OPI disable
1= STR OPI enable
Reserved
Refer to "SIO to DQS Skew
Table"
Reserved
0= Disable
1= Enable
0= 0 cycle
1= 1 cycle
Reserved
Refer to "Dummy Cycle and
Frequency Table (MHz)"
x
x
Reserved
refer to "9-3-3. Preamable
Pattern Select Bit Table"
Reserved
Reserved
Reserved
0= default DOPI Enable
1= default DOPI Disable
0= default SOPI Enable
1= default SOPI Disable
Default
x
x
1
x
Type
x
Volatile
Bit
Volatile
Bit
x
Volatile
Bit
x
Volatile
Bit
Volatile
Bit
x
Volatile
Bit
x
x
x
x
Volatile
Bit
x
OTP
x
1
OTP
1
OTP
0
0
x
001
x
0
0
x
000
x
x
x
x
0
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
9-3-1. SIO to DQS Skew Table
Options
000
001(Default)
010
011
100
101
110
111
CL=10pF
0.2
0
-0.1
-0.2
tQSQV (ns,max)
CL=15pF CL=20pF
0.2
0.1
0.2
0
0.1
-0.1
0
-0.2
-0.1
-0.1
CL=30pF
0.2
0.1
0
-0.1
-0.2
CL=10pF
1.1
1.2
1.6
2
tQXQS (ns,max)
CL=15pF CL=20pF
1.4
1.6
2.0
1.8
2.2
2.2
2.4
2.6
2.8
3.2
CL=30pF
2.8
3.2
3.6
4
4.4
9-3-2. Dummy Cycle and Frequency Table (MHz)
DC [2:0]
000(Default)
001
010
011
100
101
110
111
Numbers of Dummy Cycle
20
18
16
14
12
10
8
6
9-3-3. Preamable Pattern Select Bit Table
All SIOs (Except SIO3)
Bit 0= 0
0011 0100 1001 1010
Bit 0= 1
0101 0101 0101 0101
P/N: PM2183
26
Octa I/O STR (MHz)
200
166
166
133
104
104
84
66
Octa I/O DTR (MHz)
200
166
166
133
104
104
84
66
SIO3
0011 0101 0001 0100
0101 0101 0101 0101
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
9-4. Security Register
The definition of the Security Register bits is as below:
Erase Fail bit. The Erase Fail bit is a status flag, which shows the status of last Erase operation. It will be set to
"1", if the erase operation fails or the erase region is protected. It will be set to "0", if the last operation is successful.
Please note that it will not interrupt or stop any operation in the flash memory.
Program Fail bit. The Program Fail bit is a status flag, which shows the status of last Program operation. It will be
set to "1", if the program operation fails or the program region is protected. It will be set to "0", if the last operation is
successful. Please note that it will not interrupt or stop any operation in the flash memory.
Erase Suspend bit. Erase Suspend Bit (ESB) indicates the status of Erase Suspend operation. Users may use
ESB to identify the state of flash memory. After the flash memory is suspended by Erase Suspend command, ESB
is set to "1". ESB is cleared to "0" after erase operation resumes.
Program Suspend bit. Program Suspend Bit (PSB) indicates the status of Program Suspend operation. Users may
use PSB to identify the state of flash memory. After the flash memory is suspended by Program Suspend command,
PSB is set to "1". PSB is cleared to "0" after program operation resumes.
Secured OTP Indicator bit. The Secured OTP indicator bit shows the chip is locked by factory or not. When it is
"0", it indicates non-factory lock; "1" indicates factory-lock.
Lock-down Secured OTP (LDSO) bit. By writing WRSCUR instruction, the LDSO bit may be set to "1" for
customer lock-down purpose. However, once the bit is set to "1" (lock-down), the LDSO bit and the 8K-bit Secured
OTP area cannot be updated any more. While it is in 8K-bit secured OTP mode, main array access is not allowed.
Table 13. Security Register Definition
bit7
bit6
bit5
bit4
WPSEL
E_FAIL
P_FAIL
Reserved
0=normal
WP mode
1=individual
mode
(default=0)
0=normal
Erase
succeed
1=indicate
Erase failed
(default=0)
0=normal
Program
succeed
1=indicate
Program
failed
(default=0)
-
0=Erase
is not
suspended
1= Erase
suspended
(default=0)
Non-volatile
bit (OTP)
Volatile bit
Volatile bit
-
Volatile bit
P/N: PM2183
bit3
bit2
ESB
PSB
(Erase
(Program
Suspend bit) Suspend bit)
27
bit1
bit0
LDSO
Secured OTP
(indicate if
indicator bit
lock-down)
0 = not lock0=Program
down
0 = nonis not
1 = lock-down
factory
suspended
(cannot
lock
1= Program
program/
1 = factory
suspended
erase
lock
(default=0)
OTP)
Non-volatile
Non-volatile
Volatile bit
bit
bit (OTP)
(Read only)
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
10. COMMAND DESCRIPTION
10-1.Write Enable (WREN)
The Write Enable (WREN) instruction is for setting Write Enable Latch (WEL) bit. For those instructions like PP, SE,
BE, CE, WRSR, WRCR2, SBL, WRFBR, ESFBR, WRSCUR, WRLR, WSPB and ESSPB which are intended to
change the device content WEL bit should be set every time after the WREN instruction setting the WEL bit.
The sequence of issuing WREN instruction is: CS# goes low→sending WREN instruction code→ CS# goes high.
Figure 5. Write Enable (WREN) Sequence (SPI Mode)
CS#
0
1
2
3
4
5
6
7
SCLK
Command
SI
06h
High-Z
SO
Figure 6. Write Enable (WREN) Sequence (STR-OPI Mode)
CS#
SCLK
SIO[7:0]
06h
F9h
Figure 7. Write Enable (WREN) Sequence (DTR-OPI Mode)
CS#
SCLK
SIO[7:0]
P/N: PM2183
06h
28
F9h
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
10-2.Write Disable (WRDI)
The Write Disable (WRDI) instruction is to reset Write Enable Latch (WEL) bit. The sequence of issuing WRDI
instruction is: CS# goes low→sending WRDI instruction code→CS# goes high.
The WEL bit is reset by following situations:
- Power-up
- Reset# pin driven low
- WRDI command completion
- WRSR/WRCR/WRCR2 command completion
- PP command completion
- SE/BE/CE command completion
- SBL command completion
- PGM/ERS Suspend command completion
- Softreset command completion
- WRSCUR command completion
- WRFBR/ESFBR command completion
- WRLR/WSPB/ESSPB/WRUSPB command completion
- GBLK/GBULK command completion
Figure 8. Write Disable (WRDI) Sequence (SPI Mode)
CS#
0
1
2
3
4
5
6
7
SCLK
Command
SI
04h
High-Z
SO
Figure 9. Write Disable (WRDI) Sequence (STR-OPI Mode)
CS#
SCLK
SIO[7:0]
04h
FBh
Figure 10. Write Disable (WRDI) Sequence (DTR-OPI Mode)
CS#
SCLK
SIO[7:0]
P/N: PM2183
04h
29
FBh
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
10-3.Read Identification (RDID)
The RDID instruction is for reading the manufacturer ID of 1-byte and followed by Device ID of 2-byte. The Macronix
Manufacturer ID and Device ID are listed as Table 14 ID Definitions.
The sequence of issuing RDID instruction is: CS# goes low→ sending RDID instruction code→24-bits ID data out
on SO→ to end RDID operation can drive CS# to high at any time during data out.
While Program/Erase operation is in progress, it will not decode the RDID instruction, therefore there's no effect on
the cycle of program/erase operation which is currently in progress. When CS# goes high, the device is at standby
stage.
Table 14. ID Definitions
RDID
9Fh
Manufactory ID
Memory type
Memory density
C2
80
3A
Figure 11. Read Identification (RDID) Sequence (SPI mode)
CS#
0
1
2
3
4
5
6
7
8
9 10
13 14 15 16 17 18
28 29 30 31
SCLK
Command
SI
9Fh
Manufacturer Identification
High-Z
SO
7
6
5
2
1
MSB
Device Identification
0 15 14 13
3
2
1
0
MSB
Figure 12. Read Identification (RDID) Sequence (STR-OPI Mode)
CS#
SCLK
Pre-drive
SIO[7:0]
9Fh
60h
00
00
00
MID
00
Address
Type
Density
Dummy
Figure 13. Read Identification (RDID) Sequence (DTR-OPI Mode)
CS#
SCLK
DQS
Pre-drive
SIO[7:0]
9Fh
60h
00
00
00
MID
00
Address
P/N: PM2183
Type
Density
Dummy
30
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
10-4.Read Status Register (RDSR)
The RDSR instruction is for reading Status Register Bits. The Read Status Register can be read at any time (even
in program/erase/write status register condition). It is recommended to check the Write in Progress (WIP) bit before
sending a new instruction when a program, erase, or write status register operation is in progress.
The sequence of issuing RDSR instruction is: CS# goes low→ sending RDSR instruction code→ Status Register data
out on SO.
Figure 14. Read Status Register (RDSR) Sequence (SPI Mode)
CS#
0
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15
SCLK
command
05h
SI
Status Register Out
High-Z
SO
7
6
5
4
3
2
1
Status Register Out
0
7
6
5
4
3
2
1
0
7
MSB
MSB
Figure 15. Read Status Register (RDSR) Sequence (STR-OPI Mode)
CS#
SCLK
Pre-drive
SIO[7:0]
05h
FAh
00
00
00
SR
00
Address
SR
Dummy
Figure 16. Read Status Register (RDSR) Sequence (DTR-OPI Mode)
CS#
SCLK
DQS
Pre-drive
SIO[7:0]
05h
FAh
00
00
00
00
SR
Address
P/N: PM2183
SR
Dummy
31
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
For user to check if Program/Erase operation is finished or not, RDSR instruction flow are shown as follows:
Figure 17. Program/Erase flow with read array data
start
WREN command
RDSR command*
WEL=1?
No
Yes
Program/erase command
Write program data/address
(Write erase address)
RDSR command
WIP=0?
No
Yes
RDSR command
Read WEL=0, BP[3:0]
Read array data
(same address of PGM/ERS)
No
Verify OK?
Yes
Program/erase successfully
Program/erase
another block?
Program/erase fail
Yes
* Issue RDSR to check BP[3:0].
No
Program/erase completed
P/N: PM2183
32
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
Figure 18. Program/Erase flow without read array data (read P_FAIL/E_FAIL flag)
start
WREN command
RDSR command*
WEL=1?
No
Yes
Program/erase command
Write program data/address
(Write erase address)
RDSR command
WIP=0?
No
Yes
RDSR command
Read WEL=0, BP[3:0]
RDSCUR command
Yes
P_FAIL/E_FAIL =1 ?
No
Program/erase fail
Program/erase successfully
Program/erase
another block?
No
Yes
* Issue RDSR to check BP[3:0].
Program/erase completed
P/N: PM2183
33
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
10-5.Read Configuration Register (RDCR)
The RDCR instruction is for reading Configuration Register Bits. The Read Configuration Register can be read at
any time (even in program/erase/write configuration register condition).
The sequence of issuing RDCR instruction is: CS# goes low→ sending RDCR instruction code→ Configuration
Register data out on SO.
Figure 19. Read Configuration Register (RDCR) Sequence (SPI Mode)
CS#
0
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15
SCLK
command
15h
SI
Configuration register Out
High-Z
SO
7
6
5
4
3
2
1
0
Configuration register Out
7
6
5
4
3
2
1
0
7
MSB
MSB
Figure 20. Read Configuration Register (RDCR) (STR-OPI Mode)
CS#
SCLK
Pre-drive
SIO[7:0]
15h
00
EAh
00
00
01
CR
Address
CR
Dummy
Figure 21. Read Configuration Register (RDCR) (DTR-OPI Mode)
CS#
SCLK
DQS
Pre-drive
SIO[7:0]
15h
EAh
00
00
00
01
CR
Address
P/N: PM2183
CR
Dummy
34
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
10-6.Write Status Register (WRSR) / Write Configuration Register (WRCR)
The WRSR instruction is for changing the values of Status Register Bits and Configuration Register Bits. Before
sending WRSR instruction, the Write Enable (WREN) instruction must be decoded and executed to set the Write
Enable Latch (WEL) bit in advance. The WRSR instruction can change the value of Block Protect (BP3, BP2, BP1,
BP0) bits to define the protected area of memory (as shown in "Table 3. Protected Area Sizes"). The WRSR also
can set or reset the Status Register Write Disable (SRWD) bit, but has no effect on bit1(WEL) and bit0 (WIP) of the
status register.
In SPI, CS# must go high exactly at the 8 bits or 16 bits data boundary; In DOPI, CS# must go high while clock is
low; otherwise, the instruction will be rejected and not executed. The self-timed Write Status Register cycle time (tW)
is initiated as soon as Chip Select (CS#) goes high. The Write in Progress (WIP) bit still can be check out during
the Write Status Register cycle is in progress. The WIP sets 1 during the tW timing, and sets 0 when Write Status
Register Cycle is completed, and the Write Enable Latch (WEL) bit is reset.
Figure 22. Write Status Register (WRSR) Sequence (SPI Mode)
CS#
0
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
SCLK
command
SI
SO
01h
High-Z
Status
Register In
7
6
5
4
3
2
Configuration
Register In
1
0 15 14 13 12 11 10 9
8
MSB
Note : The CS# must go high exactly at 8 bits or 16 bits data boundary to completed the write register command.
P/N: PM2183
35
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
Figure 23. Write Status Register (WRSR) Sequence (STR-OPI Mode)
CS#
SCLK
SIO[7:0]
01h
FEh
00
00
00
00
SR
Figure 24. Write Status Register (WRSR) Sequence (DTR-OPI Mode)
CS#
SCLK
SIO[7:0]
01h
00
FEh
00
00
SR
00
Note: CS# must go high while SCLK is low.
Figure 25. Write Configuration Register (WRCR) Sequence (STR-OPI Mode)
CS#
SCLK
SIO[7:0]
01h
FEh
00
00
00
01
CR
Figure 26. Write Configuration Register (WRCR) Sequence (DTR-OPI Mode)
CS#
SCLK
SIO[7:0]
01h
FEh
00
00
00
01
CR
Note: CS# must go high while SCLK is low.
P/N: PM2183
36
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
Figure 27. WRSR flow
start
WREN command
RDSR command
WEL=1?
No
Yes
WRSR command
Write status register data
RDSR command
WIP=0?
No
Yes
RDSR command
Read WEL=0, BP[3:0]
Verify OK?
No
Yes
WRSR successfully
P/N: PM2183
WRSR fail
37
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
10-7.Read Configuration Register 2 (RDCR2)
The RDCR2 instruction is for reading Configuration Register 2. The Read Configuration Register 2 command would
be rejected while Internal write operation is in progress (WIP=1).
The sequence of issuing RDCR2 instruction is: CS# goes low→ sending RDCR2 instruction code→ Sending 4 byte
address → Configuration Register 2 data out on SO.
Figure 28. Read Configuration Register 2 (RDCR2) Sequence (SPI Mode)
CS#
SCLK
command
Address *
31 30 29
71h
SI
3
2
1
0
MSB
CR2
High-Z
SO
7
6
5
4
3
CR2
2
1
0
7
MSB
Note: * See "9-3. Configuration Register 2" for defining address .
Figure 29. Read Configuration Register 2 (RDCR2) Sequence (STR-OPI Mode)
CS#
SCLK
Pre-drive
SIO[7:0]
71h
8Eh
A[31:24] A[23:16]
A[15:8]
CR2
A[7:0]
Address *
CR2
Dummy
Note: * See "9-3. Configuration Register 2" for defining address .
Figure 30. Read Configuration Register 2 (RDCR2) (DTR-OPI Mode)
CS#
SCLK
DQS
Pre-drive
SIO[7:0]
71h
CR2
8Eh A[31:24] A[23:16] A[15:8] A[7:0]
Address *
CR2
Dummy
Note: * See "9-3. Configuration Register 2" for defining address .
P/N: PM2183
38
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
10-8.Write Configuration Register 2 (WRCR2)
The WRCR2 instruction is for changing the values of Configuration Register 2. Before sending WRCR2 instruction,
the Write Enable (WREN) instruction must be decoded and executed to set the Write Enable Latch (WEL) bit in
advance.
In SPI, CS# must go high exactly at the 8 bits data boundary; In DOPI, CS# must go high while clock is low;
otherwise, the instruction will be rejected and not executed, and the Write Enable Latch (WEL) bit is reset.
Figure 31. Write Configuration Register 2 (WRCR2) Sequence (SPI Mode)
CS#
SCLK
Command
31 30 29
72h
SI
CR2
Address *
3
2
1
0
7
6
5
4
3
2
1
0
MSB
MSB
Note 1: * See "9-3. Configuration Register 2" for defining address .
Figure 32. Write Configuration Register 2 (WRCR2) Sequence (STR-OPI Mode)
CS#
SCLK
SIO[7:0]
72h
8Dh
A[31:24]
A[23:16]
A[15:8]
A[7:0]
CR2
Address *
Note 1: * See "9-3. Configuration Register 2" for defining address .
Figure 33. Write Configuration Register 2 (WRCR2) Sequence (DTR-OPI Mode)
CS#
SCLK
SIO[7:0]
72h
8Dh
A[31:24] A[23:16] A[15:8]
A[7:0]
CR2
Address *
Note 1 : * See "9-3. Configuration Register 2" for defining address.
Note 2 : CS# must go high while SCLK is low
P/N: PM2183
39
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
10-9.Read Security Register (RDSCUR)
The RDSCUR instruction is for reading the value of Security Register bits. The Read Security Register can be read
at any time (even in program/erase/write status register/write security register condition) and continuously.
The sequence of issuing RDSCUR instruction is : CS# goes low→sending RDSCUR instruction→Security Register
data out on SO→ CS# goes high.
Figure 34. Read Security Register (RDSCUR) Sequence (SPI Mode)
CS#
0
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15
SCLK
command
2Bh
SI
Security register Out
High-Z
SO
7
6
5
4
3
2
1
Security register Out
0
7
6
5
4
3
2
1
0
7
MSB
MSB
Figure 35. Read Security Register (RDSCUR) Sequence (STR-OPI Mode)
CS#
SCLK
Pre-drive
SIO[7:0]
2Bh
D4h
00
00
00
Security
Register
00
Address
Security
Register
Dummy
Figure 36. Read Security Register (RDSCUR) Sequence (DTR-OPI Mode)
CS#
SCLK
DQS
Pre-drive
SIO[7:0]
2Bh
D4h
00
00
00
Security
Register
00
Address
P/N: PM2183
Security
Register
Dummy
40
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
10-10. Write Security Register (WRSCUR)
The WRSCUR instruction sets the LDSO bit of the Security Register. The WREN (Write Enable) instruction is
required before issuing WRSCUR instruction. The WRSCUR instruction may change the values of bit1 (LDSO bit)
for customer to lock-down the 8K-bit Secured OTP area. Once the LDSO bit is set to "1", the Secured OTP area
cannot be updated any more.
The sequence of issuing WRSCUR instruction is :CS# goes low→ sending WRSCUR instruction → CS# goes high.
The CS# must go high exactly at the boundary; otherwise, the instruction will be rejected and not executed.
Figure 37. Write Security Register (WRSCUR) Sequence (SPI Mode)
CS#
0
1
2
3
4
5
6
7
SCLK
Command
SI
2Fh
High-Z
SO
Figure 38. Write Security Register (WRSCUR) Sequence (STR-OPI Mode)
CS#
SCLK
SIO[7:0]
2Fh
D0h
Figure 39. Write Security Register (WRSCUR) Sequence (DTR-OPI Mode)
CS#
SCLK
SIO[7:0]
P/N: PM2183
2Fh
41
D0h
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
10-11.Read Data Bytes (READ)
The read instruction is for reading data out. The address is latched on rising edge of SCLK, and data shifts out on
the falling edge of SCLK at a maximum frequency fR. The address is automatically increased to the next higher
address after each byte data is shifted out, so the whole memory can be read out at a single READ instruction. The
address counter rolls over to 0 when the highest address has been reached.
The sequence of issuing READ instruction is: CS# goes low→sending READ instruction code→ 4-byte address on
SI→ data out on SO→to end READ operation can use CS# to high at any time during data out.
Figure 40. Read Data Bytes (READ) Sequence (SPI Mode only)
CS#
SCLK
command
SI
13h
32-Bit Address
31 30 29
3
2
1
0
MSB
SO
Data Out 1
High-Z
7
6
5
4
3
2
Data Out 2
1
0
7
MSB
P/N: PM2183
42
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
10-12. Read Data Bytes at Higher Speed (FAST_READ)
The FAST_READ instruction is for quickly reading data out. The address is latched on rising edge of SCLK, and
data of each bit shifts out on the falling edge of SCLK at a maximum frequency fC. The address is automatically
increased to the next higher address after each byte data is shifted out, so the whole memory can be read out at a
single FAST_READ instruction. The address counter rolls over to 0 when the highest address has been reached.
The sequence of issuing FAST_READ instruction is: CS# goes low→ sending FAST_READ instruction code→
4-byte address on SI→ 8 dummy cycles → data out on SO→ to end FAST_READ operation can use CS# to high at
any time during data out.
While Program/Erase/Write Status Register cycle is in progress, FAST_READ instruction is rejected without any
impact on the Program/Erase/Write Status Register current cycle.
Figure 41. Read at Higher Speed (FAST_READ) Sequence (SPI Mode only)
CS#
SCLK
32-Bit Address
Command
SI
0Ch
31 30 29
3
2
1
0
High-Z
SO
CS#
SCLK
Dummy Cycle
SI
7
6
5
4
3
2
1
0
DATA OUT 2
DATA OUT 1
SO
7
6
5
4
3
1
0
7
MSB
MSB
P/N: PM2183
2
43
6
5
4
3
2
1
0
7
MSB
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
10-13. OCTA Read Mode (8READ)
The 8READ instruction enable Octa throughput of Serial Flash in read mode. An OPI Enable bit of Configuration
Register 2 must be set to "1" before sending the STR Octa READ instruction.
While Program/Erase/Write Status Register cycle is in progress, 8READ instruction is rejected without any impact
on the Program/Erase/Write Status Register current cycle.
Figure 42. OCTA Read Mode Sequence (STR-OPI Mode)
≈
≈
CS#
SCLK
ECh
13h
A[31:24]
A[23:16]
A[15:8]
≈
Pre-drive
SIO[7:0]
A[7:0]
Address
P/N: PM2183
D0
D1
D2
D3
Dummy
44
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
10-14. OCTA DTR Read Mode (8DTRD)
The 8DTRD instruction enable DTR Octa throughput of Serial Flash in read mode. An DOPI Enable bit of
Configuration Register 2 must be set to "1" before sending the DTR Octa READ instruction.
While Program/Erase/Write Status Register cycle is in progress, 8DTRD instruction is rejected without any impact
on the Program/Erase/Write Status Register current cycle.
In DTR Octa READ mode, the starting address must be even byte (A0=0).
Figure 43. OCTA Read Mode Sequence (DTR-OPI Mode)
≈
CS#
≈
SCLK
EEh
≈
SIO[7:0]
≈
DQS
11h A[31:24]A[23:16] A[15:8] A[7:0]
D1
D0
D3
D2
Dummy
Address
word unit word unit
P/N: PM2183
45
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
10-15. Preamble Bit
The Preamble Bit data pattern supports system/memory controller to determine the valid windows of data output
more easily and improve data capture reliability while the flash memory is running in high frequency.
The preamble bit is designed as a 16-bit data pattern, which can be enabled or disabled by setting the bit4 of
Configuration register (Preamble bit Enable bit). Once CR<4> is set, the preamble bit is inputted into dummy
cycles. Two different patterns are selectable by setting CR<2> PSB (Pattern Select Bit), and please refer to "9-3.
Configuration Register 2" for details.
Once Preamble Bit feature is enabled, the preamble bit pattern will be output after a pre-driven signal. When the
device is under OPI mode, all SIO pins except SIO3 will output the same learning pattern. The signal on SIO3 will
be different from other I/O pins in case PSB=0.
In OPI, when dummy cycle number reaches 20, the complete 16 bits will start to output right after the pre-driven
signal. When dummy cycle number is not sufficient of 16 cycles, the rest of the preamble bits will be cut off.
In DOPI, when dummy cycles number reaches 12, the complete 16 bits will start to output right after the pre-driven
signal.
Figure 44. Preamble Bit data pattern Output Sequence (STR-OPI Mode)
CS#
SCLK
Pre-drive
SIO[7:0]
ECh
A[31:24] A[23:16]
13h
A[15:8]
A[7:0]
DLP0
Address
DLP1
DLP2
DLP3
D[7:0]
D[7:0]
Dummy
Note: 8 dummy cycle example.
Figure 45. Preamble Bit data pattern Output Sequence (DTR-OPI Mode)
CS#
SCLK
DQS
Pre-drive
SIO[7:0]
A
A
A
EEh 11h [31:24] [23:16] [15:8]
A
[7:0]
DLP0 DLP1 DLP2 DLP3 D[7:0] D[7:0] D[7:0] D[7:0]
Address
Dummy
Note: 6 dummy cycle example.
P/N: PM2183
46
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
10-16. Burst Read
To set the Burst length, following command operation is required to issue command: “C0h” in the first Byte, following
4 clocks defining wrap around enable with “0h” and disable with“1h”.
The next 4 clocks are to define wrap around depth. Their definitions are as the following table:
Data
Wrap Around
Wrap Depth
00h
Reserved
Reserved
01h
Yes
16-byte
02h
Yes
32-byte
03h
Yes
64-byte
1xh
No
X
The wrap around unit is defined within the 256Byte page, with random initial address. It is defined as “wrap-around
mode disable” for the default state of the device. To exit wrap around, it is required to issue another “C0h” command
in which data=‘1xh”. Otherwise, wrap around status will be retained until power down or reset command. To change
wrap around depth, it is requried to issue another “C0h” command in which data=“0xh”. Burst read is supported
in both SPI and OPI mode after wrap around is enable. Burst read does not support DOPI. The device is default
without Burst read.
Figure 46. Set Burst Length (SPI Mode)
CS#
0
1
2
3
4
5
6
7
8
9
D7
D6
10
1
12
13
14
15
SCLK
SIO
C0h
D5
D4
D3
D2
D1
D0
Figure 47. Set Burst Length (STR-OPI Mode)
CS#
SCLK
SIO[7:0]
P/N: PM2183
C0h
3Fh
00
00
47
00
00
SBL
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
10-17. Fast Boot
The Fast Boot Feature provides the ability to automatically execute read operation after power on cycle or reset
without any read instruction.
A Fast Boot Register is provided on this device. It can enable the Fast Boot function and also define the number of
delay cycles and start address (where boot code being transferred). Instruction WRFBR (write fast boot register)
and ESFBR (erase fast boot register) can be used for the status configuration or alternation of the Fast Boot
Register bit. RDFBR (read fast boot register) can be used to verify the program state of the Fast Boot Register. The
default number of delay cycles is 21 cycles in OPI/DOPI; while the number of delay cycles is 13 in SPI and there is
a 16bytes boundary address for the start of boot code access.
When CS# starts to go low, data begins to output from default address after the delay cycles. After CS# returns to
go high, the device will go back to standard SPI/OPI/DOPI mode and user can start to input command. In the fast
boot data out process from CS# goes low to CS# goes high, a minimum of one byte must be output.
Once Fast Boot feature has been enabled, the device will automatically start a read operation after power on cycle,
reset command, or hardware reset operation.
Fast Boot Register (FBR)
Bits
Description
FBSA (FastBoot Start
Address)
31 to 4
3
Reserved
2 to 1
FBSD (FastBoot Start
Delay Cycle)
0
FBE (FastBoot Enable)
Bit Status
Default State
16 bytes boundary address for the start of boot
FFFFFFF
code access.
1
00: 11 delay cycles
01: 15 delay cycles
10: 17 delay cycles
11: 21 delay cycles
0=FastBoot is enabled.
1=FastBoot is not enabled.
Type
NonVolatile
NonVolatile
11
NonVolatile
1
NonVolatile
Figure 48. Fast Boot Sequence (SPI Mode)
CS#
0
-
-
-
-
-
-
n
n+1 n+2 n+3 n+4 n+5 n+6 n+7 n+8 n+9 n+10 n+11n+12n+13n+14n+15
SCLK
Delay Cycles
SI
Don’t care or High Impedance
Data Out 1
SO
High Impedance
7
6
5
4
MSB
3
2
Data Out 2
1
0
7
MSB
6
5
4
3
2
1
0
7
MSB
Note: The delay cycle is always 13 in SPI mode.
P/N: PM2183
48
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
Figure 49. Fast Boot Sequence (STR-OPI Mode)
≈
CS#
1
≈
0
SCLK
n-1
n
n+1
n+2
n+3
Pre-drive
≈
SIO[7:0]
D0
D1
D2
D3
Delay Cycles
Note:
If FBSD = 11, delay cycles is 21 and n is 20.
If FBSD = 10, delay cycles is 17 and n is 16.
If FBSD = 01, delay cycles is 15 and n is 14.
If FBSD = 00, delay cycles is 11 and n is 10.
0
SCLK
DQS
1
n-2
n-1
n
n+1
≈
CS#
≈ ≈
Figure 50. Fast Boot Sequence (DTR-OPI Mode)
≈
Pre-drive
SIO[7:0]
D1
D0
D3
D2
Delay Cycles
Note:
If FBSD = 11, delay cycles is 21 and n is 21.
If FBSD = 10, delay cycles is 17 and n is 17.
If FBSD = 01, delay cycles is 15 and n is 15.
If FBSD = 00, delay cycles is 11 and n is 11.
P/N: PM2183
49
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
Figure 51. Read Fast Boot Register (RDFBR) Sequence
CS#
0
1
2
3
4
5
6
7
8
9 10
37 38 39 40 41
SCLK
Command
SI
16h
Data Out 1
High-Z
SO
7
6
5
Data Out 2
26 25 24 7
6
MSB
MSB
Figure 52. Read Fast Boot Register (RDFBR) Sequence (STR-OPI Mode)
CS#
SCLK
Pre-drive
SIO[7:0]
16h
E9h
00
00
00
00
FBR1
Address
FBR2
Dummy
Figure 53. Read Fast Boot Register (RDFBR) Sequence (DTR-OPI Mode)
CS#
SCLK
DQS
Pre-drive
SIO[7:0]
16h
E9h
00
00
00
00
FBR1
Address
P/N: PM2183
FBR2
Dummy
50
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
Figure 54. Write Fast Boot Register (WRFBR) Sequence
CS#
0
1
2
3
4
5
6
7
8
37 38 39
9 10
SCLK
Command
SI
Fast Boot Register
17h
7
6
26 25 24
5
MSB
SO
High-Z
Figure 55. Write Fast Boot Register (WRFBR) Sequence (STR-OPI Mode)
SCLK
SIO[7:0]
17h
E8h
00
00
00
00
FBR1
≈ ≈ ≈
≈
CS#
FBR4
Figure 56. Write Fast Boot Register (WRFBR) Sequence (DTR-OPI Mode)
CS#
SCLK
SIO[7:0]
P/N: PM2183
17h
E8h
00
00
00
51
00
FBR1 FBR2 FBR3 FBR4
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
Figure 57. Erase Fast Boot Register (ESFBR) Sequence
CS#
0
1
2
3
4
5
6
7
SCLK
Command
SI
18h
High-Z
SO
Figure 58. Erase Fast Boot Register (ESFBR) Sequence (STR-OPI Mode)
CS#
SCLK
SIO[7:0]
18h
E7h
Figure 59. Erase Fast Boot Register (ESFBR) Sequence (DTR-OPI Mode)
CS#
SCLK
SIO[7:0]
P/N: PM2183
18h
52
E7h
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
10-18. Sector Erase (SE)
The Sector Erase (SE) instruction is for erasing the data of the chosen sector to be "1". The instruction is used
for any 4K-byte sector. A Write Enable (WREN) instruction must execute to set the Write Enable Latch (WEL) bit
before sending the Sector Erase (SE). Any address of the sector (Please refer to "5. MEMORY ORGANIZATION")
is a valid address for Sector Erase (SE) instruction. The CS# must go high exactly at the byte boundary (the least
significant bit of the address byte been latched-in); otherwise, the instruction will be rejected and not executed.
The sequence of issuing SE instruction is: CS# goes low→ sending SE instruction code→ 4-byte address → CS#
goes high.
The self-timed Sector Erase Cycle time (tSE) is initiated as soon as Chip Select (CS#) goes high. The Write in
Progress (WIP) bit still can be checked while the Sector Erase cycle is in progress. The WIP sets 1 during the tSE
timing, and clears when Sector Erase Cycle is completed, and the Write Enable Latch (WEL) bit is cleared. If the
Block is protected by BP bits (Block Protect Mode), the Sector Erase (SE) instruction will not be executed on the
block.
Figure 60. Sector Erase (SE) Sequence (SPI Mode)
CS#
SCLK
32-Bit Address
Command
SI
31 30
21h
2
1
0
MSB
Figure 61. Sector Erase (SE) Sequence (STR-OPI Mode)
CS#
SCLK
SIO[7:0]
21h
DEh
A[31:24]
A[23:16]
A[15:8]
A[7:0]
Figure 62. Sector Erase (SE) Sequence (DTR-OPI Mode)
CS#
SCLK
SIO[7:0]
P/N: PM2183
21h
A
A
A
DEh [31:24]
[23:16] [15:8]
53
A
[7:0]
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
10-19. Block Erase (BE)
The Block Erase (BE) instruction is for erasing the data of the chosen block to be "1". The instruction is used
for 64K-byte block erase operation. A Write Enable (WREN) instruction must be executed to set the Write Enable
Latch (WEL) bit before sending the Block Erase (BE). Any address of the block (Please refer to "5. MEMORY
ORGANIZATION") is a valid address for Block Erase (BE) instruction. The CS# must go high exactly at the byte
boundary (the least significant bit of address byte been latched-in); otherwise, the instruction will be rejected and not
executed.
The sequence of issuing BE instruction is: CS# goes low→ sending BE instruction code→ 4-byte address → CS#
goes high.
The self-timed Block Erase Cycle time (tBE) is initiated as soon as Chip Select (CS#) goes high. The Write in
Progress (WIP) bit still can be checked while the Block Erase cycle is in progress. The WIP sets during the tBE
timing, and clears when Block Erase Cycle is completed, and the Write Enable Latch (WEL) bit is reset. If the Block
is protected by BP bits (Block Protect Mode), the Block Erase (BE) instruction will not be executed on the block.
Figure 63. Block Erase (BE) Sequence (SPI Mode)
CS#
SCLK
Command
SI
32-Bit Address
DCh
31 30
2
1
0
MSB
Figure 64. Block Erase (BE) Sequence (STR-OPI Mode)
CS#
SCLK
SIO[7:0]
DCh
23h
A[31:24]
A[23:16]
A[15:8]
A[7:0]
Figure 65. Block Erase (BE) Sequence (DTR-OPI Mode)
CS#
SCLK
SIO[7:0]
P/N: PM2183
DCh
23h
A
A
A
[31:24] [23:16] [15:8]
54
A
[7:0]
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
10-20. Chip Erase (CE)
The Chip Erase (CE) instruction is for erasing the data of the whole chip to be "1". A Write Enable (WREN)
instruction must be executed to set the Write Enable Latch (WEL) bit before sending the Chip Erase (CE). The CS#
must go high exactly at the byte boundary, otherwise the instruction will be rejected and not executed.
The sequence of issuing CE instruction is: CS# goes low→sending CE instruction code→CS# goes high.
The self-timed Chip Erase Cycle time (tCE) is initiated as soon as Chip Select (CS#) goes high. The Write in
Progress (WIP) bit still can be checked while the Chip Erase cycle is in progress. The WIP sets during the tCE
timing, and clears when Chip Erase Cycle is completed, and the Write Enable Latch (WEL) bit is cleared.
When the chip is under "Block protect (BP) Mode". The Chip Erase (CE) instruction will not be executed, if one (or
more) sector is protected by BP3-BP0 bits. It will be only executed when BP3-BP0 all set to "0".
Figure 66. Chip Erase (CE) Sequence (SPI Mode)
CS#
0
1
2
3
4
5
6
7
SCLK
Command
SI
60h or C7h
Figure 67. Chip Erase (CE) Sequence (STR-OPI Mode)
CS#
SCLK
SIO[7:0]
60h or C7h 9Fh or 38h
Figure 68. Chip Erase (CE) Sequence (DTR-OPI Mode)
CS#
SCLK
SIO[7:0]
P/N: PM2183
60h or
C7h
55
9Fh or
38h
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
10-21. Page Program (PP)
The Page Program (PP) instruction is for programming the memory to be "0". A Write Enable (WREN) instruction
must be executed to set the Write Enable Latch (WEL) bit before sending each Page Program (PP) command.
The device programs only the last 256 data bytes sent to the device. The last address byte (the 8 least significant
address bits, A7-A0) should be set to 0 for 256 bytes page program. If A7-A0 are not all zero, transmitted data that
exceed page length are programmed from the starting address (32-bit address that last 8 bit are all 0) of currently
selected page. If the data bytes sent to the device exceeds 256, the last 256 data byte is programmed at the request
page and previous data will be disregarded. If the data bytes sent to the device has not exceeded 256, the data
will be programmed at the request address of the page. There will be no effort on the other data bytes of the same
page.
In DTR OPI, the starting address given must be even address (A0=0) and data byte number must be even.
The sequence of issuing PP instruction is: CS# goes low→ sending PP instruction code→ 4-byte address → at least
1-byte on data in SPI and STR OPI; at least two bytes in DOPI→ CS# goes high.
The CS# must be kept to low during the whole Page Program cycle; The CS# must go high exactly at the byte
boundary in SPI (the latest eighth bit of data being latched in), CS# must go high while SCLK is low in DOPI,
otherwise the instruction will be rejected and will not be executed.
The self-timed Page Program Cycle time (tPP) is initiated as soon as Chip Select (CS#) goes high. The Write in
Progress (WIP) bit still can be checked while the Page Program cycle is in progress. The WIP sets during the tPP
timing, and clears when Page Program Cycle is completed, and the Write Enable Latch (WEL) bit is cleared. If the
page is protected by BP bits (Block Protect Mode), the Page Program (PP) instruction will not be executed.
Figure 69. Page Program (PP) Sequence (SPI Mode)
CS#
SCLK
Command
31 30 29
12h
SI
Data Byte 1
32-Bit Address
3
2
1
0
7
6
5
4
3
2
1
0
MSB
MSB
CS#
SCLK
Data Byte 2
SI
7
6
MSB
P/N: PM2183
5
4
3
2
Data Byte 3
1
0
7
6
5
4
MSB
3
2
Data Byte 256
1
0
7
6
5
4
3
2
1
0
MSB
56
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
Figure 70. Page Program (PP) Sequence (STR-OPI Mode)
tCHSH
≈
CS#
tSLCH
12h
EDh
A[31:24]
A[23:16]
A[15:8]
A[7:0]
D0
D1
≈≈
SIO[7:0]
≈
SCLK
D254
D255
Figure 71. Page Program (PP) Sequence (DTR-OPI Mode)
tCLSH
tSLCH
SCLK
SIO[7:0]
12h
A
A
A
EDh [31:24]
[23:16] [15:8]
A
[7:0]
D1
D0
word unit
≈ ≈ ≈
≈
CS#
D255
D254
word unit
Note: CS# must go high while SCLK is low.
P/N: PM2183
57
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
10-22. Deep Power-down (DP)
The Deep Power-down (DP) instruction is for setting the device to minimum power consumption (the standby
current is reduced from ISB1 to ISB2). The Deep Power-down mode requires the Deep Power-down (DP) instruction
to enter, during the Deep Power-down mode, the device is not active and all Write/Program/Erase instruction are
ignored. When CS# goes high, it's only in deep power-down mode not standby mode. It's different from Standby
mode.
The sequence of issuing DP instruction is: CS# goes low→sending DP instruction code→CS# goes high.
Once the DP instruction is set, all instruction will be ignored except the Release from Deep Power-down mode (RDP)
and Read Electronic Signature (RES) instruction and softreset command. (those instructions allow the ID being
reading out). When Power-down, or software reset command the deep power-down mode automatically stops, and
when power-up, the device automatically is in standby mode. For DP instruction the CS# must go high exactly at the
byte boundary (the latest eighth bit of instruction code been latched-in); otherwise, the instruction will not executed.
As soon as Chip Select (CS#) goes high, a delay of tDP is required before entering the Deep Power-down mode.
Figure 72. Deep Power-down (DP) Sequence (SPI Mode)
CS#
0
1
2
3
4
5
6
tDP
7
SCLK
Command
B9h
SI
Stand-by Mode
Deep Power-down Mode
Figure 73. Deep Power-down (DP) Sequence (STR-OPI Mode)
CS#
tDP
SCLK
SIO[7:0]
B9h
46h
Stand-by Mode Deep Power-down Mode
Figure 74. Deep Power-down (DP) Sequence (DTR-OPI Mode)
CS#
tDP
SCLK
SIO[7:0]
B9h
46h
Stand-by Mode Deep Power-down Mode
P/N: PM2183
58
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
10-23. Release from Deep Power-down (RDP)
The Release from Deep Power-down (RDP) instruction is completed by driving Chip Select (CS#) High. When Chip
Select (CS#) is driven High, the device is put in the Stand-by Power mode. If the device was not previously in the
Deep Power-down mode, the transition to the Stand-by Power mode is immediate. If the device was previously in
the Deep Power-down mode, though, the transition to the Stand-by Power mode is delayed by tRES2, and Chip
Select (CS#) must remain High for at least tRES2(max), as specified in Table 21 AC Characteristics. Once in the
Stand-by Power mode, the device waits to be selected, so that it can receive, decode and execute instructions. The
RDP instruction is only for releasing from Deep Power Down Mode. Reset# pin goes low will release the Flash from
deep power down mode.
Even in Deep power-down mode, the RDP is also allowed to be executed, only except the device is in progress of
program/erase/write cycle; there's no effect on the current program/erase/write cycle in progress.
Figure 75. Release from Deep Power-down (RDP) Sequence (SPI Mode)
CS#
0
1
2
3
4
5
6
tRES1
7
SCLK
Command
SI
SO
ABh
High-Z
Deep Power-down Mode
Stand-by Mode
Figure 76. Release from Deep Power-down (RDP) Sequence (STR-OPI Mode)
CS#
tRES1
SCLK
SIO[7:0]
54h
ABh
Deep Power-down Mode Stand-by Mode
Figure 77. Release from Deep Power-down (RDP) Sequence (DTR-OPI Mode)
CS#
tRES1
SCLK
SIO[7:0]
ABh
54h
Deep Power-down Mode Stand-by Mode
P/N: PM2183
59
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
10-24. Enter Secured OTP (ENSO)
The ENSO instruction is for entering the additional 8K-bit secured OTP mode. While device is in 8K-bit secured
OTP mode, main array access is not available. The additional 8K-bit secured OTP is independent from main array
and may be used to store unique serial number for system identifier. After entering the Secured OTP mode, follow
standard read or program procedure to read out the data or update data. The Secured OTP data cannot be updated
again once it is lock-down.
The sequence of issuing ENSO instruction is: CS# goes low→ sending ENSO instruction to enter Secured OTP
mode→ CS# goes high.
Please note that after issuing ENSO command user can only access secure OTP region with standard read or
program procedure. Furthermore, once security OTP is lock down, only read related commands are valid.
10-25. Exit Secured OTP (EXSO)
The EXSO instruction is for exiting the additional 8K-bit secured OTP mode.
The sequence of issuing EXSO instruction is: CS# goes low→ sending EXSO instruction to exit Secured OTP
mode→ CS# goes high.
P/N: PM2183
60
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
10-26. Write Protection Selection (WPSEL)
There are two write protection methods provided on this device, (1) Block Lock (BP) protection mode (2) Advanced
Sector protection mode. If WPSEL=0, flash is under BP protection mode. If WPSEL=1, flash is under Advanced
Sector protection mode. The default value of WPSEL is “0”. WPSEL command can be used to set WPSEL=1.
Please note that WPSEL is an OTP bit. Once WPSEL is set to 1, there is no chance to recovery WPSEL back
to “0”. If the flash is put on BP mode, the Advanced Sector protection mode is disabled. Contrarily, if flash is on the
Advanced Sector protection mode, the BP mode is disabled.
Every time after the system is powered-on, and the Security Register bit 7 is checked to be WPSEL=1, all
the blocks or sectors will be write protected by Dynamic Protected Bit (DPB) in default. User may only unlock
the blocks or sectors via GBULK instruction. Program or erase functions can only be operated after the Unlock
instruction is conducted.
When WPSEL = 0: Block Lock (BP) protection mode,
Array is protected by BP3~BP0 and BP bits are protected by “SRWD=1 and WP#=0”, where SRWD is bit 7 of status
register that can be set by WRSR command.
When WPSEL =1: Advanced Sector protection mode,
Blocks are individually protected by their own SPB or DPB lock bits which are set to “1” after power up. When the
system accepts and executes WPSEL instruction, the bit 7 in security register will be set. It will activate WRLR,
RDLR, WRSPB, ESSPB, WRDPB, RDDPB, GBLK, GBULK etc instructions to conduct block lock protection and
replace the original Software Protect Mode (SPM) use (BP3~BP0) indicated block methods. Under the Advanced
Sector protection mode (WPSEL=1), hardware protection is performed by driving WP#=0. Once WP#=0 all array
blocks/sectors are protected regardless of the contents of SPB or DPB lock bits.
The sequence of issuing WPSEL instruction is: CS# goes low → sending WPSEL instruction to enter the individual
block protect mode → CS# goes high.
Write Protection Selection
Start
(Default in BP Mode)
WPSEL=1
Set
WPSEL Bit
Advanced
Sector Protection
Solid
Protection
P/N: PM2183
WPSEL=0
Block Protection
(BP)
Dynamic
Protection
61
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
10-27. Individual Sector Protection
There is a non-volatile (SPB) protection bit related to the single sector in main flash array. Each of the sectors is
protected from programming or erasing operation when the bit is set.
The figure below helps describing an overview of these methods. The device is default to the Solid mode when
shipped from factory. The detail algorithm of advanced sector protection is shown as follows:
Figure 78. Individual Sector Protection Overview
Start
Set
SPB Lock Bit ?
SPBLKDN# = 0
SPB Lock bit locked
All SPB can not be changeable
SPBLKDN# = 1
SPB Lock bit Unlocked
SPB is changeable
Dynamic Protect Bit Register
(DPB)
DPB=1 sector protect
Sector Array
DPB=0 sector unprotect
P/N: PM2183
SPB Access Register
(SPB)
Temporary Unprotect
SPB bit (USPB)
SPB=1 Write Protect
USPB=0 SPB bit is disabled
SPB=0 Write Unprotect
USPB=1 SPB bit is effective
DPB 0
SA 0
SPB 0
DPB 1
SA 1
SPB 1
DPB 2
SA 2
SPB 2
:
:
:
:
:
:
DPB N-1
SA N-1
SPB N-1
DPB N
SA N
SPB N
62
USPB
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
10-27-1. Lock Register
The Lock Register is a 8-bit one-time programmable register. Lock Register bit [6] is SPB Lock Down Bit (SPBLKDN)
which is an unique bit assigned to control all SPB bit status.
When SPBLKDN is 1, SPB can be changed. When it is locked as 0, all SPB can not be changed anymore, and
SPBLKDN bit itself can not be altered anymore, either.
The Lock Register is programmed using the WRLR (Write Lock Register) command. A WREN command must be
executed to set the WEL bit before sending the WRLR command.
Lock Register
Bits
Field Name
Function
Type
Default
State
7
RFU
Reserved
OTP
1
6
SPBLKDN#
SPB Lock Down
OTP
1
5 to 0
RFU
Reserved
OTP
1
Description
Reserved for Future Use
1 = SPB changeable
0 = freeze SPB
Reserved for Future Use
Figure 79. Read Lock Register (RDLR) Sequence
CS#
0
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15
SCLK
command
2Dh
SI
Register Out
High-Z
SO
7
6
5
4
3
2
1
0
7
MSB
Figure 80. Read Lock Register (RDLR) Sequence (STR-OPI Mode)
CS#
SCLK
Pre-drive
SIO[7:0]
2Dh
D2h
00
00
00
Address
P/N: PM2183
LR
00
LR
Dummy
63
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
Figure 81. Read Lock Register (RDLR) Sequence (DTR-OPI Mode)
CS#
SCLK
DQS
Pre-drive
SIO[7:0]
2Dh
D2h
00
00
00
00
LR
Address
LR
Dummy
Figure 82. Write Lock Register (WRLR) Sequence
CS#
0
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15
SCLK
Command
SI
Lock Register In
2Ch
7
6
5
4
3
2
1
0
MSB
High-Z
SO
Figure 83. Write Lock Register (WRLR) Sequence (STR-OPI Mode)
CS#
SCLK
SIO[7:0]
2Ch
D3h
00
00
00
00
LR
Figure 84. Write Lock Register (WRLR) Sequence (DTR-OPI Mode)
CS#
SCLK
SIO[7:0]
2Ch
D3h
00
00
00
00
LR
Note: CS# must go high while SCLK is low.
P/N: PM2183
64
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
10-27-2. Solid Protection Bits
The Solid Protection Bits (SPBs) are nonvolatile bits for enabling or disabling write-protection to sectors and blocks.
The SPB bits have the same endurance as the Flash memory. An SPB is assigned to each 4KB sector in the bottom
and top 64KB of memory and to each 64KB block in the remaining memory. The factory default state of the SPB bits
is “0”, which has the sector/block write-protection disabled.
When an SPB is set to “1”, the associated sector or block is write-protected. Program and erase operations on the
sector or block will be inhibited. SPBs can be individually set to “1” by the WRSPB command. However, the SPBs
cannot be individually cleared to “0”. Issuing the ESSPB command clears all SPBs to “0”. A WREN command must
be executed to set the WEL bit before sending the WRSPB or ESSPB command.
The RDSPB command reads the status of the SPB of a sector or block. The RDSPB command returns 00h if the
SPB is “0”, indicating write-protection is disabled. The RDSPB command returns FFh if the SPB is “1”, indicating
write-protection is enabled.
Note: If SPBLKDN=0, commands to set or clear the SPB bits will be ignored.
SPB Register
Bit
Description
7 to 0 SPB (Solid Protection Bit)
P/N: PM2183
Bit Status
00h = Unprotect Sector / Block
FFh = Protect Sector / Block
65
Default
Type
00h
Non-volatile
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
Figure 85. Read SPB Status (RDSPB) Sequence
CS#
Mode 3
0
1
2
3
4
5
6
7
8
37 38 39 40 41 42 43 44 45 46 47
9
SCLK
Mode 0
Command
SI
32-Bit Address
E2h
A31 A30
A2 A1 A0
MSB
Data Out
High-Z
SO
7
6
5
4
3
2
1
0
MSB
Figure 86. Read SPB Status (RDSPB) Sequence (STR-OPI Mode)
≈
CS#
≈
SCLK
E2h
1Dh
A[31:24]
A[23:16]
A[15:8]
≈
Pre-drive
SIO[7:0]
A[7:0]
Address
SPB
SPB
Dummy
Figure 87. Read SPB Status (RDSPB) Sequence (DTR-OPI Mode)
≈
CS#
≈
≈
SCLK
DQS
Pre-drive
E2h
A
A
A
1Dh [31:24] [23:16] [15:8]
A
[7:0]
≈
SIO[7:0]
Address
P/N: PM2183
SPB
SPB
Dummy
66
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
Figure 88. SPB Erase (ESSPB) Sequence
CS#
0
1
2
3
4
5
6
7
SCLK
Command
SI
E4h
High-Z
SO
Figure 89. SPB Erase (ESSPB) Sequence (STR-OPI Mode)
CS#
SCLK
SIO[7:0]
E4h
1Bh
Figure 90. SPB Erase (ESSPB) Sequence (DTR-OPI Mode)
CS#
SCLK
E4h
SIO[7:0]
P/N: PM2183
67
1Bh
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
Figure 91. SPB Program (WRSPB) Sequence
CS#
0
1
2
3
4
5
6
7
8
37 38 39
9
SCLK
Command
SI
32-Bit Address
E3h
A31 A30
A2 A1 A0
MSB
Figure 92. SPB Program (WRSPB) Sequence (STR-OPI Mode)
CS#
SCLK
SIO[7:0]
E3h
1Ch
A[31:24]
A[23:16]
A[15:8]
A[7:0]
Figure 93. SPB Program (WRSPB) Sequence (DTR-OPI Mode)
CS#
SCLK
SIO[7:0]
P/N: PM2183
E3h
1Ch
A
A
A
[31:24] [23:16] [15:8]
68
A
[7:0]
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
10-27-3. Dynamic Write Protection Bits
The Dynamic Protection features a volatile type protection to each individual sector. It can protect sectors from
unintentional change, and is easy to disable when there are necessary changes.
All DPBs are default as protected (FFh) after reset or upon power up cycle. Via setting up Dynamic Protection bit (DPB)
by write DPB command (WRDPB), user can cancel the Dynamic Protection of associated sector.
The Dynamic Protection only works on those unprotected sectors whose SPBs are cleared. After the DPB state is
cleared to “0”, the sector can be modified if the SPB state is unprotected state.
DPB Register
Bit
Description
7 to 0
DPB (Dynamic protected Bit)
Bit Status
Default
00h= DPB for the sector address unprotected
FFh
FFh= DPB for the sector address protected
Type
Volatile
Figure 94. Read DPB Register (RDDPB) Sequence
CS#
Mode 3
0
1
2
3
4
5
6
7
8
37 38 39 40 41 42 43 44 45 46 47
9
SCLK
Mode 0
Command
SI
32-Bit Address
E0h
A31 A30
A2 A1 A0
MSB
Data Out
High-Z
SO
7
6
5
4
3
2
1
0
MSB
Figure 95. Read DPB Register (RDDPB) Sequence (STR-OPI Mode)
≈
CS#
≈
SCLK
E0h
1Fh
A[31:24]
A[23:16]
A[15:8]
A[7:0]
Address
P/N: PM2183
≈
Pre-drive
SIO[7:0]
DPB
DPB
Dummy
69
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
Figure 98. Read DPB Register (RDDPB) Sequence (DTR-OPI Mode)
≈
CS#
≈
≈
SCLK
DQS
Pre-drive
E0h
A
A
A
A
[7:0]
1Fh [31:24] [23:16] [15:8]
≈
SIO[7:0]
Address
DPB
DPB
Dummy
Figure 96. Write DPB Register (WRDPB) Sequence
CS#
Mode 3
0
1
2
3
4
5
6
7
8
37 38 39 40 41 42 43 44 45 46 47
9
SCLK
Mode 0
Command
SI
Data Byte 1
32-Bit Address
E1h
A31 A30
7
A2 A1 A0
MSB
6
5
4
3
2
1
0
MSB
Figure 97. Write DPB Register (WRDPB) Sequence (STR-OPI Mode)
CS#
SCLK
SIO[7:0]
E1h
1Eh
A[31:24]
A[23:16]
A[15:8]
A[7:0]
DPB
Address
Figure 99. Write DPB Register (WRDPB) Sequence (DTR-OPI Mode)
CS#
SCLK
SIO[7:0]
E1h
1Eh A[31:24] A[23:16] A[15:8] A[7:0]
DPB
Address
P/N: PM2183
70
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
10-27-4. Temporary Un-protect Solid write protect bit (USPB)
Temporary Un-protect Solid write Protect Bit is volatile bit. Software can temporarily unprotect write protect sectors
despite of SPBs' property when DPBs are cleared. While the USPB=0, all the SPBs’ property is masked.
Notes:
1. Upon power up, the USPB status is default protected. The USPB can be unprotected (to “0”) or protected (to “1”)
as often as needed. The hardware reset will reset USPB/DPB to their default values.
2. Please refer to "10-27-6. Sector Protection States Summary Table" for the sector state with the protection status
of DPB/SPB/USPB bits.
10-27-5. Gang Block Lock/Unlock (GBLK/GBULK)
These instructions are only effective after WPSEL was executed. The GBLK/GBULK instruction is a chip-based
protected or unprotected operation. It can enable or disable all DPB.
The WREN (Write Enable) instruction is required before issuing GBLK/GBULK instruction.
The sequence of issuing GBLK/GBULK instruction is: CS# goes low → send GBLK/GBULK (7Eh/98h) instruction
→CS# goes high.
Both SPI (8 clocks) and QPI (2 clocks) command cycle can accept by this instruction. The SIO[3:1] are don't care
when during SPI mode.
The CS# must go high exactly at the byte boundary, otherwise, the instruction will be rejected and not be executed.
10-27-6. Sector Protection States Summary Table
DPB bit
0
0
0
0
1
1
1
1
P/N: PM2183
Protection Status
SPB bit
0
0
1
1
0
0
1
1
Sector State
USPB bit
0
1
0
1
0
1
0
1
Unprotect
Unprotect
Unprotect
Protect
Protect
Protect
Protect
Protect
71
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
10-28. Program/Erase Suspend/Resume
The device allow the interruption of Sector-Erase, Block-Erase or Page-Program operations and conduct other
operations.
After issue suspend command, the system can determine if the device has entered the Erase-Suspended mode
through Bit2 (PSB) and Bit3 (ESB) of security register. (please refer to "Table 13. Security Register Definition")
10-29. Erase Suspend
Erase suspend allow the interruption of all erase operations. After the device has entered Erase-Suspended mode,
the system can read any sector(s) or Block(s) except those being erased by the suspended erase operation.
Reading the sector or Block being erase suspended is invalid.
After erase suspend, WEL bit will be clear, following commands can be accepted. (including: 0Ch, ECh, EEh, 5Ah,
C0h, 06h, 04h, 2Bh, 9Fh, 05h, ABh, 30h, 66h, 99h, 00h, 15h, 16h, 13h, 0Ch, ECh, 2Dh, E2h, 71h, 72h)
Erase Suspend Bit (ESB) indicates the status of Erase Suspend operation. Users may use ESB to identify the
state of flash memory. After the flash memory is suspended by Erase Suspend command, ESB is set to "1". ESB is
cleared to "0" after erase operation resumes.
10-30. Program Suspend
Program suspend allows the interruption of all program operations. After the device has entered ProgramSuspended mode, the system can read any sector(s) or Block(s) except those be­ing programmed by the suspended
program operation. Reading the sector or Block being program suspended is invalid.
After program suspend, WEL bit will be cleared, only read related, resume and reset command can be accepted.
(including: 0Ch, ECh, EEh, 5Ah, C0h, 06h, 04h, 2Bh, 9Fh, 05h, ABh, 30h, 66h, 99h, 00h, 15h, 16h, 0Ch, ECh, 2Dh,
E2h, 71h, 72h)
Program Suspend Bit (PSB) indicates the status of Program Suspend operation. Users may use PSB to identify the
state of flash memory. After the flash memory is suspended by Program Suspend command, PSB is set to "1". PSB
is cleared to "0" after program operation resumes.
P/N: PM2183
72
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
Figure 100. Suspend to Read/Program Latency
CS#
Suspend Command
tPSL / tESL
Read/Program
Command
tPSL: Program Latency
tESL: Erase Latency
Figure 101. Resume to Read Latency
tSE / tBE / tPP
CS#
Read Command
Resume Command
Figure 102. Resume to Suspend Latency
CS#
Resume Command
tPRS / tERS
Suspend Command
tPRS: Program Resume to another Suspend
tERS: Erase Resume to another Suspend
P/N: PM2183
73
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
10-31. Write-Resume
The Write operation is being resumed when Write-Resume instruction issued. ESB or PSB (suspend status bit) in
Status register will be changed back to “0”.
The operation of Write-Resume is as follows: CS# drives low → send write resume command cycle (30h) → drive
CS# high. By polling Busy Bit in status register, the internal write operation status could be checked to be completed
or not. The user may also wait the time lag of tSE, tBE, tPP for Sector-erase, Block-erase or Page-programming.
WREN (command "06") is not required to issue before resume. Resume to another suspend operation requires
latency time of 100us (from Program Suspend Resume)/200us (from Erase Suspend Resume).
Please note that, if "performance enhance mode" is executed during suspend operation, the device can not be
resume. To restart the write command, disable the "performance enhance mode" is required. After the "performance
enhance mode" is disable, the write-resume command is effective.
10-32. No Operation (NOP)
The “No Operation” command is only able to terminate the Reset Enable (RSTEN) command and will not affect any
other command.
10-33. Software Reset (Reset-Enable (RSTEN) and Reset (RST))
The Software Reset operation combines two instructions: Reset-Enable (RSTEN) command following a Reset (RST)
command. It returns the device to a standby mode. All the volatile bits and settings will be cleared then, which
makes the device return to the default status as power on.
To execute Reset command (RST), the Reset-Enable (RSTEN) command must be executed first to perform the
Reset operation. If there is any other command to interrupt after the Reset-Enable command, the Reset-Enable will
be invalid.
If the Reset command is executed during program or erase operation, the operation will be disabled, the data under
processing could be damaged or lost.
The reset time is different depending on the last operation. For details, please refer to "Table 17. Reset Timing(Other Operation)" for tREADY2.
P/N: PM2183
74
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
Figure 103. Software Reset Recovery
Stand-by Mode
66
CS#
99
tREADY2
Mode
Note: Refer to "Table 17. Reset Timing-(Other Operation)" for tREADY2.
Figure 104. Reset Sequence (SPI mode)
TSHSL
CS#
SCLK
Command
Command
99h
66h
SIO0
Figure 105. Reset Sequence (STR-OPI mode)
TSHSL
CS#
SCLK
SIO[7:0]
66h
99h
99h
66h
99h
66h
Figure 106. Reset Sequence (DTR-OPI mode)
TSHSL
CS#
SCLK
SIO[7:0]
P/N: PM2183
66h
99h
75
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
11. Serial Flash Discoverable Parameter (SFDP)
11-1.Read SFDP Mode (RDSFDP)
The Serial Flash Discoverable Parameter (SFDP) standard provides a consistent method of describing the functional
and feature capabilities of serial flash devices in a standard set of internal parameter tables. These parameter tables
can be interrogated by host system software to enable adjustments needed to accommodate divergent features
from multiple vendors. The concept is similar to the one found in the Introduction of JEDEC Standard, JESD68 on
CFI.
The sequence of issuing RDSFDP instruction in SPI is CS# goes low→send RDSFDP instruction (5Ah)→send 3
address bytes on SI pin→ send 8 dummy cycles → read SFDP code on SO→to end RDSFDP operation can use
CS# to high at any time during data out.
SFDP in SPI is a JEDEC standard, JESD216.
The sequcn of issuing RDSFDP instruction in OPI/DOPI mode:
CS# low → send RDSFDP instruction (5Ah/A5h) → send 4 address bytes on SIO pin→ send 20 dummy cycles →
read SFDP code on SIO[7:0] → to end RDSFDP operation can use CS# to high at any time during data out.
Figure 107. Read Serial Flash Discoverable Parameter (RDSFDP) Sequence
CS#
0
1
2
3
4
5
6
7
8
9 10
28 29 30 31
SCLK
Command
SI
SO
24 BIT ADDRESS
23 22 21
5Ah
3
2
1
0
High-Z
CS#
32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47
SCLK
Dummy Cycle
SI
7
6
5
4
3
2
1
0
DATA OUT 2
DATA OUT 1
SO
7
6
5
P/N: PM2183
4
3
2
1
0
7
MSB
MSB
76
6
5
4
3
2
1
0
7
MSB
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
Figure 108. Read Serial Flash Discoverable Parameter (RDSFDP) Sequence (STR-OPI Mode)
1
2
3
4
5
≈ ≈
CS#
6
SCLK
26
27
28
Pre-drive
A5h
A[31:24] A[23:16]
A[15:8]
A[7:0]
≈
SIO[7:0]
5Ah
Address
D0
D1
D2
20 Dummy
Figure 109. Read Serial Flash Discoverable Parameter (RDSFDP) Sequence (DTR-OPI Mode)
≈
CS#
1
2
3
4
23
5Ah
≈
≈
DQS
SIO[7:0]
25
≈
SCLK
24
A5h A[31:24]A[23:16] A[15:8] A[7:0]
D1
D0
D3
D2
20 Dummy
Address
word unit word unit
Note: Address must be low byte (A0=0) in DTR OPI.
Table 15. Signature and Parameter Identification Data Values (TBD)
P/N: PM2183
77
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
12. RESET
Driving the RESET# pin low for a period of tRLRH or longer will reset the device. After reset cycle, the device is at
the following states:
- Standby mode
- All the volatile bits such as WEL/WIP will return to the default status as power on.
- All the volatile bits in CR2 will return to the default status as power on.
If the device is under programming or erasing, driving the RESET# pin low will also terminate the operation and data
could be lost. During the resetting cycle, the SIO data becomes high impedance and the current will be reduced to
minimum.
Figure 110. RESET Timing
CS#
tRHSL
SCLK
tRH tRS
RESET#
tRLRH
tREADY1 / tREADY2
Table 16. Reset Timing-(Standby)
Symbol Parameter
tRHSL Reset# high before CS# low
tRS
Reset# setup time
tRH
Reset# hold time
tRLRH Reset# low pulse width
tREADY1 Reset Recovery time
Min.
10
15
15
10
35
Typ.
Max.
Unit
us
ns
ns
us
us
Min.
10
15
15
10
40
40
310
12
25
100
40
Typ.
Max.
Unit
us
ns
ns
us
us
us
us
ms
ms
ms
ms
Table 17. Reset Timing-(Other Operation)
Symbol
tRHSL
tRS
tRH
tRLRH
Parameter
Reset# high before CS# low
Reset# setup time
Reset# hold time
Reset# low pulse width
Reset Recovery time (During instruction decoding)
Reset Recovery time (for read operation)
Reset Recovery time (for program operation)
tREADY2 Reset Recovery time(for SE4KB operation)
Reset Recovery time (for BE64K operation)
Reset Recovery time (for Chip Erase operation)
Reset Recovery time (for WRSR operation)
P/N: PM2183
78
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
13. POWER-ON STATE
The device is at below states when power-up:
- Standby mode (please note it is not deep power-down mode)
- Write Enable Latch (WEL) bit is reset
The device must not be selected during power-up and power-down stage unless the VCC achieves below correct
level:
- VCC minimum at power-up stage and then after a delay of tVSL
- GND at power-down
Please note that a pull-up resistor on CS# may ensure a safe and proper power-up/down level.
An internal power-on reset (POR) circuit may protect the device from data corruption and inadvertent data change
during power up state. When VCC is lower than VWI (POR threshold voltage value), the internal logic is reset and
the flash device has no response to any command.
For further protection on the device, if the VCC does not reach the VCC minimum level, the correct operation is not
guaranteed. The write, erase, and program command should be sent after the below time delay:
- tVSL after VCC reached VCC minimum level
The device can accept read command after VCC reached VCC minimum and a time delay of tVSL.
Please refer to the ""Power-up Timing"".
Note:
- To stabilize the VCC level, the VCC rail decoupled by a suitable capacitor close to package pins is
recommended. (generally around 0.1uF)
- At power-down stage, the VCC drops below VWI level, all operations are disable and device has no response
to any command. The data corruption might occur during the stage while a write, program, erase cycle is in
progress.
- To stabilize the VCCQ level, the VCCQ/VSSQ rail decoupled by a suitable capacitor close to package pins is
recommended. One VCCQ pin connect to one capacitor.
- It is recommended VCC and VCCQ power are separated system supply with same supply voltage.
P/N: PM2183
79
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
14. ELECTRICAL SPECIFICATIONS
Table 18. ABSOLUTE MAXIMUM RATINGS
RATING
VALUE
Ambient Operating Temperature
Industrial grade
-40°C to 85°C
Storage Temperature
-65°C to 150°C
Applied Input Voltage
-0.5V to VCC+0.5V
Applied Output Voltage
-0.5V to VCC+0.5V
VCC to Ground Potential
-0.5V to 2.5V
NOTICE:
1.Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage
to the device. This is stress rating only and functional operational sections of this specification is not implied.
Exposure to absolute maximum rating conditions for extended period may affect reliability.
2. Specifications contained within the following tables are subject to change.
3. During voltage transitions, all pins may overshoot to VCC+1.0V or -1.0V for period up to 20ns.
Figure 112. Maximum Positive Overshoot Waveform
Figure 111. Maximum Negative Overshoot Waveform
20ns
0V
VCC+1.0V
-1.0V
2.0V
20ns
Table 19. CAPACITANCE TA = 25°C, f = 1.0 MHz
Symbol Parameter
CIN
COUT
P/N: PM2183
Min.
Typ.
Max.
Unit
Input Capacitance
16
pF
VIN = 0V
Output Capacitance
16
pF
VOUT = 0V
80
Conditions
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
Figure 113. INPUT TEST WAVEFORMS AND MEASUREMENT LEVEL
Input timing reference level
0.8VCC
Output timing reference level
0.7VCC
AC
Measurement
Level
0.3VCC
0.2VCC
0.5VCC
Note: Input pulse rise and fall time are <1.5ns
Figure 114. OUTPUT LOADING
25K ohm
DEVICE UNDER
TEST
CL
+1.8V
25K ohm
CL=30pF Including jig capacitance
P/N: PM2183
81
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
Table 20. DC CHARACTERISTICS
Temperature = -40°C to 85°C, VCC = 1.7V ~ 2.0V
Symbol Parameter
Notes
Min.
Typ.
Max.
Units Test Conditions
ILI
Input Load Current
1
±2
uA
VCC = VCC Max,
VIN = VCC or GND
ILO
Output Leakage Current
1
±2
uA
VCC = VCC Max,
VOUT = VCC or GND
ISB1
VCC Standby Current
1
30
100
uA
VIN = VCC or GND,
CS# = VCC
ISB2
Deep Power-down
Current
5
65
uA
VIN = VCC or GND,
CS# = VCC
15
25
mA
200MHz 8IO STR
(SIO floating)
25
35
mA
200MHz 8IO DTR
(SIO floating)
40
60
mA
20
40
mA
1
40
60
mA
Erase in Progress,
CS#=VCC
1
40
60
mA
Erase in Progress,
CS#=VCC
-0.4
0.3VCC
V
0.7VCC
VCC+0.4
V
0.2
V
IOL=100uA
V
IOH=-100uA
ICC1
ICC2
VCC Read
VCC Program Current
VIL
VCC Write Status
Register (WRSR) Current
VCC Sector/Block (32K,
64K) Erase Current
(SE/BE/BE32K)
VCC Chip Erase Current
(CE)
Input Low Voltage
VIH
Input High Voltage
VOL
Output Low Voltage
VOH
Output High Voltage
ICC3
ICC4
ICC5
1
1
VCC-0.2
Program in Progress,
CS# = VCC
Program status register in
progress, CS#=VCC
Notes :
1. Typical values at VCC = 1.8V, T = 25°C. These currents are valid for all product versions (package and speeds).
2. Typical value is calculated by simulation.
P/N: PM2183
82
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
Table 21. AC CHARACTERISTICS
Temperature = -40°C to 85°C, VCC = 1.7V ~ 2.0V
Symbol
fSCLK
fRSCLK
Alt. Parameter
fC Clock Frequency for all commands(except Read Operation)
fR Clock Frequency for READ instructions
Clock Frequency for FAST READ
fTSCLK
tCH(1)
tCL(1)
Clock Frequency for 8READ, 8DTRD
tCLH Clock High Time
tCL Clock Low Time
tCLCH(2)/
tCHCL(2)
tSLCH
tCHSL
tCSS
tSHSL
tCSH
tDVCH
tDSU
tDVCH /
tDVCL
tCHDX
tDH
tCHDX /
tCLDX
tCHSH
tCLSH
tSHCH
tSHQZ(2)
tCLQLZ
tDIS
tCLQV /
tCHQV
tV
tCLQX
tHO
tQSQV
P/N: PM2183
fSCLK ≤ 100MHz
fSCLK ≤ 133MHz
fSCLK ≤ 166MHz
fSCLK > 166MHz
CS# Active Setup Time (relative to SCLK)
CS# Not Active Hold Time (relative to SCLK)
Read
CS# Deselect Time
Write/Erase/Program
STR ≤ 133MHz
Data In Setup Time
STR > 133MHz
DTR ≤ 100MHz
DTR ≤ 133MHz
(10)
Data setup time
DTR ≤ 166MHz
DTR > 166MHz
STR ≤ 133MHz
Data In Hold Time
STR > 133MHz
DTR ≤ 100MHz
DTR ≤ 133MHz
Data hold time (10)
DTR ≤ 166MHz
DTR > 166MHz
CS# Active Hold Time (relative to
STR
SCLK)
CS# active hold time
DTR
CS# Not Active Setup Time (relative STR
to SCLK)
DTR
Output Disable Time
SIO pre-drive active time
Loading: 30pF
Loading: 20pF
Clock Low to Output Valid
Loading: 15pF
Loading: 10pF
Output Hold Time
100MHz DTR mode DQS to SIO valid skew. CL=30pF(9)
133MHz DTR mode DQS to SIO valid skew. CL=20pF(9)
166MHz DTR mode DQS to SIO valid skew. CL=15pF(9)
200MHz DTR mode DQS to SIO valid skew. CL=10pF(9)
Clock Rise Time (peak to peak) /
Clock Fall Time (peak to peak)
83
Min.
Typ.
Max.
133
50
133
Unit
MHz
MHz
MHz
"9-3-2. Dummy Cycle and
Frequency Table (MHz)"
MHz
0.45*T
0.45*T
0.6
0.8
1
1.2
4.5
3
10
40
2
1
1
0.8
0.6
0.4
2
1
1
0.8
0.6
0.4
ns
ns
V/ns
V/ns
V/ns
V/ns
ns
ns
ns
ns
3
ns
3
3
3
ns
ns
ns
ns
ns
1
ns
ns
ns
ns
8
5
8
7
6
5
0
0
0
0
ns
ns
ns
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
Symbol
tQXQS
tDP(2)
(2)
tRES1
(2)
tRES2
tW
tBP
tPP(4)
tSE
tBE
tCE
tESL(6)
tPSL(6)
tPRS(7)
tERS(8)
Alt. Parameter
DTR mode DQ hold skew
Loading: 30pF(9)
Loading: 20pF(9)
Loading: 15pF(9)
Loading: 10pF(9)
CS# High to Deep Power-down Mode
CS# High to Standby Mode without Electronic Signature
Read
CS# High to Standby Mode with Electronic Signature Read
Write Status/Configuration Register Cycle Time
Byte-Program
Page Program Cycle Time
Sector Erase Cycle Time
Block Erase (64KB) Cycle Time
Chip Erase Cycle Time
Erase Suspend Latency
Program Suspend Latency
Latency between Program Resume and next Suspend
Latency between Erase Resume and next Suspend
Min.
Typ.
20
0.2
35
300
200
0.3
0.3
100
400
Max.
3.6
2.4
1.8
1.2
10
Unit
30
us
30
40
30
1.5
120
650
320
25
25
us
ms
us
ms
ms
ms
s
us
us
us
us
ns
us
Notes:
1. tCH + tCL must be greater than or equal to 1/ Frequency.
2. Typical values given for TA=25°C. Not 100% tested.
3. Test condition is shown as Figure 113 and Figure 114.
4. While programming consecutive bytes, Page Program instruction provides optimized timings by selecting to
program the whole 256 bytes or only a few bytes between 1~256 bytes.
5. By default dummy cycle value. Please refer to the "Table 1. Operating Frequency Comparison".
6. Latency time is required to complete Erase/Program Suspend operation until WIP bit is "0".
7. For tPRS, minimum timing must be observed before issuing the next program suspend command. However, a
period equal to or longer than the typical timing is required in order for the program operation to make progress.
8. For tERS, minimum timing must be observed before issuing the next erase suspend command. However, a
period equal to or longer than the typical timing is required in order for the erase operation to make progress.
9. DQSSKW bits in CR2 must be set to the corresponding value. See "9-3-1. SIO to DQS Skew Table".
10. tDVCH+tCHDX>1.5ns for each SIO; tDVCL+tCLDX>1.5ns for each SIO.
P/N: PM2183
84
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
15. OPERATING CONDITIONS
At Device Power-Up and Power-Down
AC timing illustrated in Figure 115 and Figure 116 are for the supply voltages and the control signals at device
power-up and power-down. If the timing in the figures is ignored, the device will not operate correctly.
During power-up and power-down, CS# needs to follow the voltage applied on VCC to keep the device not to be
selected. The CS# can be driven low when VCC reach Vcc(min.) and wait a period of tVSL.
Figure 115. AC Timing at Device Power-Up
VCC
VCC(min)
GND
tVR
tSHSL
CS#
tSLCH
tCHSL
tCHSH
tSHCH
SCLK
tDVCH
tCHCL
tCHDX
LSB IN
MSB IN
SI
High Impedance
SO
Symbol
tVR
tCLCH
Parameter
VCC Rise Time
Notes
1
Min.
20
Max.
500000
Unit
us/V
Notes :
1.Sampled, not 100% tested.
2.For AC spec tCHSL, tSLCH, tDVCH, tCHDX, tSHSL, tCHSH, tSHCH, tCHCL, tCLCH in the figure, please refer to
Table 21. AC CHARACTERISTICS.
P/N: PM2183
85
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
Figure 116. Power-Down Sequence
During power-down, CS# needs to follow the voltage drop on VCC to avoid mis-operation.
VCC
CS#
SCLK
Figure 117. Power-up Timing
VCC
VCC(max)
Chip Selection is Not Allowed
VCC(min)
tVSL
Device is fully accessible
VWI
time
P/N: PM2183
86
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
Figure 118. Power Up/Down and Voltage Drop
For Power-down to Power-up operation, the VCC of flash device must below VPWD for at least tPWD timing. Please
check the table below for more detail.
VCC
VCC (max.)
Chip Select is not allowed
VCC (min.)
V_keep
tVSL
VWI
Full Device
Access
Allowed
VPWD (max.)
tPWD
Time
Table 22. Power-Up/Down Voltage and Timing
Symbol
tPWD
Parameter
VCC voltage needed to below VPWD for ensuring initialization
will occur
Voltage that a re-initialization is necessary if VDD drop
below to VKEEP
The minimum duration for ensuring initialization will occur
tVSL
VCC(min.) to device operation
3
tVR
VCC Rise Time
20
500000
us/V
VCC
VCC Power Supply
1.7
2.0
V
VWI
Write Inhibit Voltage
1.0
1.4
V
VPWD
V_keep
Min.
Max.
Unit
0.8
V
1.5
V
300
us
ms
15-1.INITIAL DELIVERY STATE
The device is delivered with the memory array erased: all bits are set to 1 (each byte contains FFh). The Status
Register contains 00h (all Status Register bits are 0).
P/N: PM2183
87
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
16. ERASE AND PROGRAMMING PERFORMANCE
Parameter
Typ. (1)
Min.
Max. (2)
Unit
40
ms
Write Status Register Cycle Time
Sector Erase Cycle Time (4KB)
35
120
ms
Block Erase Cycle Time (64KB)
300
650
ms
Chip Erase Cycle Time
200
320
s
Byte Program Time (via page program command)
20
30
us
Page Program Time
0.2
1.5
ms
Erase/Program Cycle
100,000
cycles
Note:
1. Typical program and erase time assumes the following conditions: 25°C, 1.8V, and checkboard pattern.
2. Under worst conditions of 85°C and 1.7V.
3. System-level overhead is the time required to execute the first-bus-cycle sequence for the programming
command.
4. The maximum chip programming time is evaluated under the worst conditions of 0°C, VCC=1.8V, and 100K
cycle with 90% confidence level.
17. DATA RETENTION
Parameter
Condition
Min.
Data retention
55˚C
20
Max.
Unit
years
18. LATCH-UP CHARACTERISTICS
Min.
Max.
Input Voltage with respect to GND on all power pins, SI, CS#
-1.0V
2 VCCmax
Input Voltage with respect to GND on SO
-1.0V
VCC + 1.0V
-100mA
+100mA
Current
Includes all pins except VCC. Test conditions: VCC = 3.0V, one pin at a time.
P/N: PM2183
88
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
19. ORDERING INFORMATION
PART NO.
MX25UM51245GXDI
P/N: PM2183
CLOCK (MHz)
TEMPERATURE
PACKAGE
200
-40°C~85°C
24-Ball BGA
(5x5 ball array)
89
Remark
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
20. PART NAME DESCRIPTION
MX 25 UM 51245G XD
I
TEMPERATURE RANGE:
I: Industrial (-40°C to 85°C)
PACKAGE:
XD: 24-Ball BGA (5x5 ball array)
DENSITY & MODE:
51245G: 512Mb
TYPE:
UM: 1.8V
DEVICE:
25: Serial Flash
P/N: PM2183
90
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
21. PACKAGE INFORMATION
P/N: PM2183
91
REV. 0.02, JUN. 02, 2015
ADVANCED INFORMATION
MX25UM51245G
22. REVISION HISTORY
Revision No.
0.01
Description
Page
Date
1. Added Individual Sector Protection information
P18,21,29,61-71 APR/28/2015
2. Updated parameters for DC/AC Characteristics
P82-84
3. Added V_keep to Figure 118 and Table 22P87
4. Content correction All
0.02
1. Detached Automotive specs 2. Content correction
P/N: PM2183
ALL
JUN/02/2015
P13,29,47,49,72
92
REV. 0.02, JUN. 02, 2015
MX25UM51245G
Except for customized products which have been expressly identified in the applicable agreement, Macronix's
products are designed, developed, and/or manufactured for ordinary business, industrial, personal, and/or
household applications only, and not for use in any applications which may, directly or indirectly, cause death,
personal injury, or severe property damages. In the event Macronix products are used in contradicted to their
target usage above, the buyer shall take any and all actions to ensure said Macronix's product qualified for its
actual use in accordance with the applicable laws and regulations; and Macronix as well as it’s suppliers and/or
distributors shall be released from any and all liability arisen therefrom.
Copyright© Macronix International Co., Ltd. 2014~2015. All rights reserved, including the trademarks and
tradename thereof, such as Macronix, MXIC, MXIC Logo, MX Logo, Integrated Solutions Provider, NBit, Nbit,
NBiit, Macronix NBit, eLiteFlash, HybridNVM, HybridFlash, XtraROM, Phines, KH Logo, BE-SONOS, KSMC,
Kingtech, MXSMIO, Macronix vEE, Macronix MAP, Rich Au­dio, Rich Book, Rich TV, and FitCAM. The names
and brands of third party referred thereto (if any) are for identification purposes only.
For the contact and order information, please visit Macronix’s Web site at: http://www.macronix.com
MACRONIX INTERNATIONAL CO., LTD. reserves the right to change product and specifications without notice.
93