MX25L6436E

MX25L6436E
MX25L6436E
HIGH PERFORMANCE
SERIAL FLASH SPECIFICATION
P/N: PM1772
1
REV. 2.0, AUG. 02, 2012
MX25L6436E
Contents
FEATURES................................................................................................................................................................... 5
GENERAL DESCRIPTION.......................................................................................................................................... 7
Table 1. Additional Features ........................................................................................................................ 7
PIN CONFIGURATION................................................................................................................................................. 8
PIN DESCRIPTION....................................................................................................................................................... 8
BLOCK DIAGRAM........................................................................................................................................................ 9
DATA PROTECTION................................................................................................................................................... 10
Table 2. Protected Area Sizes.................................................................................................................... 11
Table 3. 4K-bit Secured OTP Definition..................................................................................................... 11
Memory Organization................................................................................................................................................ 12
Table 4. Memory Organization................................................................................................................... 12
DEVICE OPERATION................................................................................................................................................. 13
Figure 1. Serial Modes Supported (for Normal Serial mode).....................................................................13
COMMAND DESCRIPTION........................................................................................................................................ 14
Table 5. Command Sets............................................................................................................................. 14
(1) Write Enable (WREN).................................................................................................................................. 16
(2) Write Disable (WRDI)................................................................................................................................... 16
(3) Read Identification (RDID)........................................................................................................................... 16
(4) Read Status Register (RDSR)..................................................................................................................... 17
(5) Write Status Register (WRSR)..................................................................................................................... 18
Protection Modes.............................................................................................................................................. 18
(6) Read Data Bytes (READ)............................................................................................................................ 19
(7) Read Data Bytes at Higher Speed (FAST_READ)...................................................................................... 19
(8) Dual Read Mode (DREAD).......................................................................................................................... 19
(9) Quad Read Mode (QREAD)........................................................................................................................ 19
(10) Sector Erase (SE)...................................................................................................................................... 20
(11) Block Erase (BE)........................................................................................................................................ 20
(12) Block Erase (BE32K)................................................................................................................................. 20
(13) Chip Erase (CE)......................................................................................................................................... 21
(14) Page Program (PP)................................................................................................................................... 21
(15) 4 x I/O Page Program (4PP)...................................................................................................................... 22
Program/Erase Flow(1) with read array data.................................................................................................... 23
Program/Erase Flow(2) without read array data............................................................................................... 24
(16) Continuously program mode (CP mode)................................................................................................... 25
(17) Deep Power-down (DP)............................................................................................................................. 26
(18) Release from Deep Power-down (RDP), Read Electronic Signature (RES)............................................. 26
(19) Read Electronic Manufacturer ID & Device ID (REMS), (REMS2), (REMS4)........................................... 26
Table 6. ID Definitions ............................................................................................................................... 27
(20) Enter Secured OTP (ENSO)...................................................................................................................... 27
(21) Exit Secured OTP (EXSO)......................................................................................................................... 27
(22) Read Security Register (RDSCUR)........................................................................................................... 27
Security Register Definition............................................................................................................................... 28
(23) Write Security Register (WRSCUR)........................................................................................................... 28
(24) Write Protection Selection (WPSEL).......................................................................................................... 29
P/N: PM1772
2
REV. 2.0, AUG. 02, 2012
MX25L6436E
BP and SRWD if WPSEL=0.............................................................................................................................. 29
The individual block lock mode is effective after setting WPSEL=1.................................................................. 30
WPSEL Flow..................................................................................................................................................... 31
(25) Single Block Lock/Unlock Protection (SBLK/SBULK)................................................................................ 32
Block Lock Flow................................................................................................................................................ 32
Block Unlock Flow............................................................................................................................................. 33
(26) Read Block Lock Status (RDBLOCK)........................................................................................................ 34
(27) Gang Block Lock/Unlock (GBLK/GBULK)................................................................................................. 34
(28) Clear SR Fail Flags (CLSR)....................................................................................................................... 34
(29) Enable SO to Output RY/BY# (ESRY)....................................................................................................... 34
(30) Disable SO to Output RY/BY# (DSRY)...................................................................................................... 34
(31) Read SFDP Mode (RDSFDP).................................................................................................................... 35
Table 7. Signature and Parameter Identification Data Values ................................................................... 36
Table 8. Parameter Table (0): JEDEC Flash Parameter Tables................................................................. 37
Table 9. Parameter Table (1): Macronix Flash Parameter Tables.............................................................. 39
POWER-ON STATE.................................................................................................................................................... 41
ELECTRICAL SPECIFICATIONS............................................................................................................................... 42
ABSOLUTE MAXIMUM RATINGS.................................................................................................................... 42
Figure 3. Maximum Negative Overshoot Waveform..................................................................................42
CAPACITANCE TA = 25°C, f = 1.0 MHz............................................................................................................ 42
Figure 4. Maximum Positive Overshoot Waveform....................................................................................42
Figure 5. INPUT TEST WAVEFORMS AND MEASUREMENT LEVEL......................................................43
Figure 6. OUTPUT LOADING...................................................................................................................43
Table 10. DC CHARACTERISTICS .......................................................................................................... 44
Table 11. AC CHARACTERISTICS........................................................................................................... 45
Timing Analysis......................................................................................................................................................... 47
Figure 7. Serial Input Timing......................................................................................................................47
Figure 8. Output Timing..............................................................................................................................47
Figure 9. WP# Setup Timing and Hold Timing during WRSR when SRWD=1..........................................48
Figure 10. Write Enable (WREN) Sequence (Command 06).....................................................................48
Figure 11. Write Disable (WRDI) Sequence (Command 04)......................................................................48
Figure 12. Read Identification (RDID) Sequence (Command 9F)..............................................................49
Figure 13. Read Status Register (RDSR) Sequence (Command 05)........................................................49
Figure 14. Write Status Register (WRSR) Sequence (Command 01).......................................................49
Figure 15. Read Data Bytes (READ) Sequence (Command 03)...............................................................50
Figure 16. Read at Higher Speed (FAST_READ) Sequence (Command 0B)...........................................50
Figure 17. Dual Read Mode Sequence (Command 3B)............................................................................50
Figure 18. Quad Read Mode Sequence (Command 6B)...........................................................................51
Figure 19. Sector Erase (SE) Sequence (Command 20)...........................................................................52
Figure 20. Block Erase (BE/BE32K) Sequence (Command D8/52)...........................................................52
Figure 21. Chip Erase (CE) Sequence (Command 60 or C7)....................................................................52
Figure 22. Page Program (PP) Sequence (Command 02)........................................................................53
Figure 23. 4 x I/O Page Program (4PP) Sequence (Command 38)...........................................................53
Figure 24. Continously Program (CP) Mode Sequence with Hardware Detection (Command AD)...........54
Figure 25. Deep Power-down (DP) Sequence (Command B9).................................................................54
Figure 26. Read Electronic Signature (RES) Sequence (Command AB)...................................................55
Figure 27. Release from Deep Power-down (RDP) Sequence (Command AB)........................................55
Figure 28. Read Electronic Manufacturer & Device ID (REMS) Sequence (Command 90 or EF or DF)...56
P/N: PM1772
3
REV. 2.0, AUG. 02, 2012
MX25L6436E
Figure 29. Write Protection Selection (WPSEL) Sequence (Command 68)..............................................56
Figure 30. Single Block Lock/Unlock Protection (SBLK/SBULK) Sequence (Command 36/39)................57
Figure 31. Read Block Protection Lock Status (RDBLOCK) Sequence (Command 3C)...........................57
Figure 32. Gang Block Lock/Unlock (GBLK/GBULK) Sequence (Command 7E/98).................................57
Figure 33. Power-up Timing.......................................................................................................................58
Table 12. Power-Up Timing ....................................................................................................................... 58
INITIAL DELIVERY STATE............................................................................................................................... 58
OPERATING CONDITIONS........................................................................................................................................ 59
Figure 34. AC Timing at Device Power-Up.................................................................................................59
Figure 35. Power-Down Sequence............................................................................................................60
ERASE AND PROGRAMMING PERFORMANCE..................................................................................................... 61
DATA RETENTION..................................................................................................................................................... 61
LATCH-UP CHARACTERISTICS............................................................................................................................... 61
ORDERING INFORMATION....................................................................................................................................... 62
PART NAME DESCRIPTION...................................................................................................................................... 63
PACKAGE INFORMATION......................................................................................................................................... 64
REVISION HISTORY .................................................................................................................................................. 67
P/N: PM1772
4
REV. 2.0, AUG. 02, 2012
MX25L6436E
64M-BIT [x 1/x 2/x 4] CMOS MXSMIOTM (SERIAL MULTI I/O) FLASH MEMORY
FEATURES
GENERAL
• Serial Peripheral Interface compatible -- Mode 0 and Mode 3
• 64Mb: 67,108,864 x 1 bit structure or 33,554,432 x 2 bits (two I/O mode) structure or 16,777,216 x 4 bits (four I/
O mode) structure
• 2048 Equal Sectors with 4K bytes each
- Any Sector can be erased individually
• 256 Equal Blocks with 32K bytes each
- Any Block can be erased individually
• 128 Equal Blocks with 64K bytes each
- Any Block can be erased individually
• Power Supply Operation
- 2.7 to 3.6 volt for read, erase, and program operations
• Latch-up protected to 100mA from -1V to Vcc +1V
PERFORMANCE
• High Performance
VCC = 2.7~3.6V
- Normal read
- 50MHz
- Fast read (Normal Serial Mode)
- 1 I/O: 104MHz with 8 dummy cycles
- 2 I/O: 70MHz with 8 dummy cycles
- 4 I/O: 75MHz with 8 dummy cycles
- Fast program time: 1.4ms(typ.) and 5ms(max.)/page (256-byte per page)
- Byte program time: 9us (typical)
- Continuously Program mode (automatically increase address under word program mode)
- Fast erase time: 60ms (typ.)/sector (4K-byte per sector) ; 0.7s(typ.) /block (64K-byte per block); 50s(typ.) /chip
• Low Power Consumption
- Low active read current: 19mA(max.) at 104MHz, 15mA(max.) at 66MHz and 10mA(max.) at 33MHz
- Low active programming current: 25mA (max.)
- Low active erase current: 25mA (max.)
- Low standby current: 50uA (max.)
- Deep power down current: 20uA (max.)
• Typical 100,000 erase/program cycles
• 20 years data retention
SOFTWARE FEATURES
• Input Data Format
- 1-byte Command code
• Advanced Security Features
- BP0-BP3 block group protect
- Flexible individual block protect when OTP WPSEL=1
- Additional 4K bits secured OTP for unique identifier
P/N: PM1772
5
REV. 2.0, AUG. 02, 2012
MX25L6436E
• Auto Erase and Auto Program Algorithms
- Automatically erases and verifies data at selected sector
- Automatically programs and verifies data at selected page by an internal algorithm that automatically times the
program pulse width (Any page to be programed should have page in the erased state first.)
• Status Register Feature
• Electronic Identification
- JEDEC 1-byte Manufacturer ID and 2-byte Device ID
- RES command for 1-byte Device ID
- REMS, REMS2 and REMS4 commands for 1-byte Manufacturer ID and 1-byte Device ID
• Support Serial Flash Discoverable Parameters (SFDP) mode
HARDWARE FEATURES
• SCLK Input
- Serial clock input
• SI/SIO0
- Serial Data Input or Serial Data Input/Output for 2 x I/O mode and 4 x I/O mode
• SO/SIO1
- Serial Data Output or Serial Data Input/Output for 2 x I/O mode and 4 x I/O mode
• WP#/SIO2
- Hardware write protection or serial data Input/Output for 4 x I/O mode
• NC/SIO3
- NC pin or serial data Input/Output for 4 x I/O mode
• PACKAGE
- 16-pin SOP (300mil)
- 8-WSON (8x6mm)
- 8-pin SOP (200mil)
- All devices are RoHS Compliant
P/N: PM1772
6
REV. 2.0, AUG. 02, 2012
MX25L6436E
GENERAL DESCRIPTION
MX25L6436E is 67,108,864 bits serial Flash memory, which is configured as 8,388,608 x 8 internally. When it is in
two or four I/O mode, the structure becomes 33,554,432 bits x 2 or 16,777,216 bits x 4. The MX25L6436E features
a serial peripheral interface and software protocol allowing operation on a simple 3-wire bus. The three bus signals
are a clock input (SCLK), a serial data input (SI), and a serial data output (SO). Serial access to the device is enabled by CS# input.
MX25L6436E provides high performance read mode, which may latch address and data on both rising and falling
edge of clock. By using this high performance read mode, the data throughput may be doubling. Moreover, the performance may reach direct code execution, the RAM size of the system may be reduced and further saving system
cost.
MX25L6436E, MXSMIOTM (Serial Multi I/O) flash memory, provides sequential read operation on the whole chip and
multi-I/O features.
When it is in dual I/O mode, the SI pin and SO pin become SIO0 pin and SIO1 pin for address/dummy bits input and
data output. When it is in quad I/O mode, the SI pin, SO pin, WP# pin and NC pin become SIO0 pin, SIO1 pin, SIO2
pin and SIO3 pin for address/dummy bits input and data Input/Output.
After program/erase command is issued, auto program/erase algorithms which program/erase and verify the specified page or sector/block locations will be executed. Program command is executed on byte basis, or page (256
bytes) basis, or word basis. Continuously Program mode and erase command are executed on 4K-byte sector, 32Kbyte/64K-byte block, or whole chip basis.
To provide user with ease of interface, a status register is included to indicate the status of the chip. The status read
command can be issued to detect completion status of a program or erase operation via the WIP bit.
When the device is not in operation and CS# is high, it is put in standby mode and draws less than 100uA DC current.
The MX25L6436E utilizes Macronix's proprietary memory cell, which reliably stores memory contents even after
100,000 program and erase cycles.
Table 1. Additional Features
Additional
Features
Part
Name
MX25L6436E
Protection and Security
Read Performance
Flexible or
Individual block (or
sector) protection
4K-bit
secured OTP
1 I/O Read (104
MHz)
2 I/O Read (70
MHz)
4 I/O Read (75
MHz)
V
V
V
V
V
Additional
Features
Part
Name
MX25L6436E
P/N: PM1772
Identifier
RES
(command: AB
hex)
REMS
(command: 90 hex)
REMS2
(command: EF
hex)
REMS4
(command: DF
hex)
RDID
(command: 9F hex)
16 (hex)
C2 16 (hex)
C2 16 (hex)
C2 16 (hex)
C2 20 17 (hex)
7
REV. 2.0, AUG. 02, 2012
MX25L6436E
PIN CONFIGURATION
PIN DESCRIPTION
16-PIN SOP (300mil) *
NC/SIO3
VCC
NC
NC
NC
NC
CS#
SO/SIO1
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
SYMBOL
DESCRIPTION
CS#
Chip Select
Serial Data Input (for 1xI/O)/ Serial Data
SI/SIO0
Input & Output (for 2xI/O or 4xI/O mode)
Serial Data Output (for 1xI/O)/Serial
SO/SIO1 Data Input & Output (for 2xI/O or 4xI/O
mode)
SCLK
Clock Input
Write protection: connect to GND or
WP#/SIO2 Serial Data Input & Output (for 4xI/O
mode)
NC pin (Not connect) or Serial Data
NC/SIO3
Input & Output (for 4xI/O mode)
VCC
+ 3.3V Power Supply
GND
Ground
NC
No Connection
SCLK
SI/SIO0
NC
NC
NC
NC
GND
WP#/SIO2
8-PIN SOP (200mil)
CS#
SO/SIO1
WP#/SIO2
GND
1
2
3
4
8
7
6
5
VCC
NC/SIO3
SCLK
SI/SIO0
8-WSON (8x6mm) *
CS#
SO/SIO1
WP#/SIO2
GND
1
2
3
4
8
7
6
5
VCC
NC/SIO3
SCLK
SI/SIO0
* Advanced Information
P/N: PM1772
8
REV. 2.0, AUG. 02, 2012
MX25L6436E
BLOCK DIAGRAM
X-Decoder
Address
Generator
Memory Array
Page Buffer
SI/SIO0
Data
Register
Y-Decoder
SRAM
Buffer
Sense
Amplifier
CS#
WP#/SIO2
NC/SIO3
SCLK
Mode
Logic
State
Machine
Clock Generator
Output
Buffer
SO/SIO1
P/N: PM1772
HV
Generator
9
REV. 2.0, AUG. 02, 2012
MX25L6436E
DATA PROTECTION
During power transition, there may be some false system level signals which result in inadvertent erasure or programming. The device is designed to protect itself from these accidental write cycles.
The state machine will be reset as standby mode automatically during power up. In addition, the control register
architecture of the device constrains that the memory contents can only be changed after specific command sequences have completed successfully.
In the following, there are several features to protect the system from the accidental write cycles during VCC powerup and power-down or from system noise.
• Valid command length checking: The command length will be checked whether it is at byte base and completed
on byte boundary.
• Write Enable (WREN) command: WREN command is required to set the Write Enable Latch bit (WEL) before issuing other commands to change data. The WEL bit will return to reset stage under following situations:
- Power-up
- Write Disable (WRDI) command completion
- Write Status Register (WRSR) command completion
- Page Program (PP, 4PP) command completion
- Continuously Program mode (CP) instruction completion
- Sector Erase (SE) command completion
- Block Erase (BE, BE32K) command completion
- Chip Erase (CE) command completion
- Single Block Lock/Unlock (SBLK/SBULK) instruction completion
- Gang Block Lock/Unlock (GBLK/GBULK) instruction completion
• Deep Power Down Mode: By entering deep power down mode, the flash device also is under protected from
writing all commands except Release from Deep Power Down mode command (RDP) and Read Electronic Signature command (RES).
I. Block lock protection
- The Software Protected Mode (SPM) uses (BP3, BP2, BP1, BP0) bits to allow part of memory to be protected
as read only. The protected area definition is shown as table of "Protected Area Sizes", the protected areas are
more flexible which may protect various area by setting value of BP0-BP3 bits. Please refer to table of "Protected Area Sizes".
- The Hardware Protected Mode (HPM) uses WP#/SIO2 to protect the (BP3, BP2, BP1, BP0) bits and SRWD
bit. If the system goes into four I/O mode, the feature of HPM will be disabled.
- MX25L6436E provides individual block (or sector) write protect & unprotect. User may enter the mode with
WPSEL command and conduct individual block (or sector) write protect with SBLK instruction, or SBULK for
individual block (or sector) unprotect. Under the mode, user may conduct whole chip (all blocks) protect with
GBLK instruction and unlock the whole chip with GBULK instruction.
P/N: PM1772
10
REV. 2.0, AUG. 02, 2012
MX25L6436E
Table 2. Protected Area Sizes
Status bit
Protection Area
BP3
BP2
BP1
BP0
64Mb
0
0
0
0
0 (none)
0
0
0
1
1 (2 blocks, block 126th-127th)
0
0
1
0
2 (4 blocks, block 124th-127th)
0
0
1
1
3 (8 blocks, block 120th-127th)
0
1
0
0
4 (16 blocks, block 112nd-127th)
0
1
0
1
5 (32 blocks, block 96th-127th)
0
1
1
0
6 (64 blocks, block 64th-127th)
0
1
1
1
7 (128 blocks, all)
1
0
0
0
8 (128 blocks, all)
1
0
0
1
9 (128 blocks, all)
1
0
1
0
10 (128 blocks, all)
1
0
1
1
11 (128 blocks, all)
1
1
0
0
12 (128 blocks, all)
1
1
0
1
13 (128 blocks, all)
1
1
1
0
14 (128 blocks, all)
1
1
1
1
15 (128 blocks, all)
Note: The device is ready to accept a Chip Erase instruction if, and only if, all Block Protect (BP3, BP2, BP1, BP0) are 0.
II. Additional 4K-bit secured OTP for unique identifier: to provide 4K-bit One-Time Program area for setting device unique serial number - Which may be set by factory or system maker. Please refer to Table 3. 4K-bit Secured OTP Definition.
- Security register bit 0 indicates whether the chip is locked by factory or not.
- To program the 4K-bit secured OTP by entering 4K-bit secured OTP mode (with ENSO command), and going
through normal program procedure, and then exiting 4K-bit secured OTP mode by writing EXSO command.
- Customer may lock-down the customer lockable secured OTP by writing WRSCUR(write security register)
command to set customer lock-down bit1 as "1". Please refer to table of "Security Register Definition" for security register bit definition and table of "4K-bit Secured OTP Definition" for address range definition.
- Note: Once lock-down whatever by factory or customer, it cannot be changed any more. While in 4K-bit Secured OTP mode, array access is not allowed.
Table 3. 4K-bit Secured OTP Definition
Address range
Size
Standard Factory Lock
xxx000~xxx00F
128-bit
ESN (electrical serial number)
xxx010~xxx1FF
3968-bit
N/A
P/N: PM1772
11
Customer Lock
Determined by customer
REV. 2.0, AUG. 02, 2012
MX25L6436E
Memory Organization
Table 4. Memory Organization
Block(64K-byte) Block(32K-byte)
Sector (4K-byte)
126
252
individual block
lock/unlock unit:64K-byte
251
125
250
7F8FFFh
2039
7F7000h
7F7FFFh
…
individual 16 sectors
lock/unlock unit:4K-byte
2032
7F0000h
7F0FFFh
2031
7EF000h
7EFFFFh
…
253
7F8000h
2024
7E8000h
7E8FFFh
2023
7E7000h
7E7FFFh
…
254
2040
2016
7E0000h
7E0FFFh
2015
7DF000h
7DFFFFh
…
127
7FFFFFh
2008
7D8000h
7D8FFFh
2007
7D7000h
7D7FFFh
2000
7D0000h
7D0FFFh
47
02F000h
02FFFFh
…
255
Address Range
7FF000h
…
2047
1
2
1
0
0
027FFFh
32
020000h
020FFFh
31
01F000h
01FFFFh
…
028FFFh
027000h
…
3
028000h
39
24
018000h
018FFFh
23
017000h
017FFFh
…
4
individual block
lock/unlock unit:64K-byte
40
16
010000h
010FFFh
15
00F000h
00FFFFh
8
008000h
008FFFh
7
007000h
007FFFh
000000h
000FFFh
…
2
0
P/N: PM1772
individual 16 sectors
lock/unlock unit:4K-byte
…
5
…
individual block
lock/unlock unit:64K-byte
12
REV. 2.0, AUG. 02, 2012
MX25L6436E
DEVICE OPERATION
1. Before a command is issued, status register should be checked to ensure device is ready for the intended operation.
2. When incorrect command is inputted to this device, it enters standby mode and remains in standby mode until
next CS# falling edge. In standby mode, SO pin of the device is High-Z.
3. When correct command is inputted to this device, it enters active mode and remains in active mode until next
CS# rising edge.
4. For standard single data rate serial mode, input data is latched on the rising edge of Serial Clock (SCLK) and
data is shifted out on the falling edge of SCLK. The difference of Serial mode 0 and mode 3 is shown as Figure 1.
5. For the following instructions: RDID, RDSR, RDSCUR, READ, FAST_READ, RDSFDP, DREAD, QREAD, RDBLOCK, RES, REMS, REMS2, and REMS4 the shifted-in instruction sequence is followed by a data-out sequence. After any bit of data being shifted out, the CS# can be high. For the following instructions: WREN, WRDI,
WRSR, SE, BE, BE32K, CE, PP, CP, 4PP, RDP, DP, WPSEL, SBLK, SBULK, GBLK, GBULK, ENSO, EXSO,
WRSCUR, ESRY, DSRY and CLSR the CS# must go high exactly at the byte boundary; otherwise, the instruction will be rejected and not executed.
6. While a Write Status Register, Program or Erase operation is in progress, access to the memory array is neglected and will not affect the current operation of Write Status Register, Program, Erase.
Figure 1. Serial Modes Supported (for Normal Serial mode)
CPOL
CPHA
shift in
(Serial mode 0)
0
0
SCLK
(Serial mode 3)
1
1
SCLK
SI
shift out
MSB
SO
MSB
Note:
CPOL indicates clock polarity of Serial master, CPOL=1 for SCLK high while idle, CPOL=0 for SCLK low while not
transmitting. CPHA indicates clock phase. The combination of CPOL bit and CPHA bit decides which Serial mode is
supported.
P/N: PM1772
13
REV. 2.0, AUG. 02, 2012
MX25L6436E
COMMAND DESCRIPTION
Table 5. Command Sets
COMMAND
(byte)
Command
(hex)
Input
Cycles
Dummy
Cycles
Action
COMMAND
(byte)
Command
(hex)
Input
Cycles
Dummy
Cycles
WREN
(write enable)
WRDI
(write disable)
RDID
(read
identification)
RDSR
(read status
register)
WRSR
(write status
register)
READ
(read data)
FAST READ
(fast read data)
06
04
9F
05
01
03
0B
Data(8)
ADD(24)
ADD(24)
8
sets the (WEL)
resets the
outputs JEDEC to read out the to write new
write enable
(WEL) write
ID: 1-byte
values of the
values to the
latch bit
enable latch bit Manufacturer status register status register
ID & 2-byte
Device ID
Command
(hex)
Input
Cycles
Dummy
Cycles
Action
P/N: PM1772
n bytes read
out until CS#
goes high
RDSFDP
(Read SFDP)
DREAD
(1I 2O read)
QREAD
(1I 4O read)
4PP
(quad page
program)
SE
(sector erase)
BE
(block erase
64KB)
BE 32K
(block erase
32KB)
5A
3B
6B
38
20
D8
52
ADD(24)
ADD(24)
ADD(24)
ADD(6)+
Data(512)
ADD(24)
ADD(24)
ADD(24)
8
8
8
Read SFDP
mode
Action
COMMAND
(byte)
n bytes read
out until CS#
goes high
n bytes read
n bytes read
quad input to
to erase the
to erase the
to erase the
out by Dual
out by Quad
program the selected sector selected 64KB selected 32KB
output until
output until
selected page
block
block
CS# goes high CS# goes high
CP
DP (Deep
(Continuously
power down)
program mode)
CE
(chip erase)
PP (Page
program)
60 or C7
02
AD
ADD(24)+
Data(2048)
ADD(24)+
Data(16)
B9
RDP
REMS
RES
(Release from
(read electronic
(read electronic
deep power
manufacturer &
ID)
down)
device ID)
AB
AB
90
ADD(24)
24
to erase whole to program the
chip
selected page
continously
program
whole chip,
the address is
automatically
increase
enters deep
power down
mode
14
release from
deep power
down mode
to read out
output the
1-byte Device Manufacturer
ID
ID & Device ID
REV. 2.0, AUG. 02, 2012
MX25L6436E
COMMAND
(byte)
Command
(hex)
Input
Cycles
Dummy
Cycles
Action
ESRY
DSRY
REMS2
REMS4 (read ENSO (enter EXSO (exit
RDSCUR
WRSCUR
(enable SO (disable SO
(read ID for ID for 4x I/O
secured
secured
(read security (write security
to output RY/ to output RY/
2x I/O mode)
mode)
OTP)
OTP)
register)
register)
BY#)
BY#)
EF
DF
ADD(24)
ADD(24)
output the
Manufacturer
ID & Device
ID
output the
Manufacturer ID &
device ID
COMMAND CLSR (Clear
(byte)
SR Fail Flags)
Command
(hex)
Input
Cycles
Dummy
Cycles
Action
30
B1
C1
2B
2F
70
80
to enter
to exit the 4K- to read value to set the to enable SO to disable SO
the 4K-bit
bit Secured
of security lock-down bit to output RY/ to output RY/
Secured OTP OTP mode
register
as "1" (once BY# during BY# during
mode
lock-down,
CP mode
CP mode
cannot be
updated)
WPSEL (write
protection
selection)
SBLK (single
block lock)
*Note 2
68
36
39
3C
ADD(24)
ADD(24)
ADD(24)
RDBLOCK
SBULK (single
(block protect
block unlock)
read)
clear security
to enter and individual block individual block read individual
register bit 6 enable individal (64K-byte) or (64K-byte) or block or sector
and bit 5
block protect sector (4K-byte) sector (4K-byte) write protect
mode
write protect
unprotect
status
GBLK (gang
block lock)
GBULK (gang
block unlock)
7E
98
whole chip
write protect
whole
chip unprotect
Notes:
1. It is not recommended to adopt any other code not in the command definition table, which will potentially enter the hidden
mode.
2: In individual block write protection mode, all blocks/sectors are locked as defualt.
P/N: PM1772
15
REV. 2.0, AUG. 02, 2012
MX25L6436E
(1) Write Enable (WREN)
The Write Enable (WREN) instruction is for setting Write Enable Latch (WEL) bit. For those instructions like PP, 4PP,
CP, SE, BE, BE32K, CE, WRSR, SBLK, SBULK, GBLK and GBULK, which are intended to change the device content, should be set every time after the WREN instruction setting the WEL bit.
The sequence of issuing WREN instruction is: CS# goes low→ sending WREN instruction code→ CS# goes high.
(Please refer to Figure 10)
(2) Write Disable (WRDI)
The Write Disable (WRDI) instruction is for resetting Write Enable Latch (WEL) bit.
The sequence of issuing WRDI instruction is: CS# goes low→ sending WRDI instruction code→ CS# goes high. (Please
refer to Figure 11)
The WEL bit is reset by following situations:
- Power-up
- Write Disable (WRDI) instruction completion
- Write Status Register (WRSR) instruction completion
- Page Program (PP, 4PP) instruction completion
- Sector Erase (SE) instruction completion
- Block Erase (BE, BE32K) instruction completion
- Chip Erase (CE) instruction completion
- Continuously Program mode (CP) instruction completion
- Single Block Lock/Unlock (SBLK/SBULK) instruction completion
- Gang Block Lock/Unlock (GBLK/GBULK) instruction completion
(3) Read Identification (RDID)
The RDID instruction is for reading the Manufacturer ID of 1-byte and followed by Device ID of 2-byte. The MXIC
Manufacturer ID is C2(hex), the memory type ID is 20(hex) as the first-byte Device ID, and the individual Device ID
of second-byte ID are listed as table of "ID Definitions". (Please refer to Table 6)
The sequence of issuing RDID instruction is: CS# goes low→ sending RDID instruction code → 24-bits ID data out
on SO→ to end RDID operation can use CS# to high at any time during data out. (Please refer to Figure 12)
While Program/Erase operation is in progress, it will not decode the RDID instruction, so there's no effect on the cycle of program/erase operation which is currently in progress. When CS# goes high, the device is at standby stage.
P/N: PM1772
16
REV. 2.0, AUG. 02, 2012
MX25L6436E
(4) Read Status Register (RDSR)
The RDSR instruction is for reading Status Register. The Read Status Register can be read at any time (even in
program/erase/write status register condition) and continuously. It is recommended to check the Write in Progress (WIP)
bit before sending a new instruction when a program, erase, or write status register operation is in progress.
The sequence of issuing RDSR instruction is: CS# goes low→ sending RDSR instruction code→ Status Register
data out on SO (Please refer to Figure 13).
The definition of the status register bits is as below:
WIP bit. The Write in Progress (WIP) bit, a volatile bit, indicates whether the device is busy in program/erase/write
status register progress. When WIP bit sets to 1, which means the device is busy in program/erase/write status
register progress. When WIP bit sets to 0, which means the device is not in progress of program/erase/write status
register cycle.
WEL bit. The Write Enable Latch (WEL) bit, a volatile bit, indicates whether the device is set to internal write enable
latch. When WEL bit sets to "1", which means the internal write enable latch is set, the device can accept program/
erase/write status register instruction. When WEL bit sets to 0, which means no internal write enable latch; the device will not accept program/erase/write status register instruction. The program/erase command will be ignored and
will reset WEL bit if it is applied to a protected memory area.
BP3, BP2, BP1, BP0 bits. The Block Protect (BP3, BP2, BP1, BP0) bits, non-volatile bits, indicate the protected area (as
defined in Table 2) of the device to against the program/erase instruction without hardware protection mode being
set. To write the Block Protect (BP3, BP2, BP1, BP0) bits requires the Write Status Register (WRSR) instruction to
be executed. Those bits define the protected area of the memory to against Page Program (PP), Sector Erase (SE),
Block Erase (BE) and Chip Erase (CE) instructions (only if all Block Protect bits set to 0, the CE instruction can be
executed).
QE bit. The Quad Enable (QE) bit, non-volatile bit, while it is "0" (factory default), it performs non-Quad and WP# is
enable. While QE is "1", it performs Quad I/O mode and WP# is disabled. In the other word, if the system goes into
four I/O mode (QE=1), the feature of HPM will be disabled.
SRWD bit. The Status Register Write Disable (SRWD) bit, non-volatile bit, default value is "0". SRWD bit is operated together with Write Protection (WP#/SIO2) pin for providing hardware protection mode. The hardware protection
mode requires SRWD sets to 1 and WP#/SIO2 pin signal is low stage. In the hardware protection mode, the Write
Status Register (WRSR) instruction is no longer accepted for execution and the SRWD bit and Block Protect bits (BP3,
BP2, BP1, BP0) are read only.
Status Register
bit7
bit6
SRWD (status
register write
protect)
QE
(Quad
Enable)
1= Quad
1=status
Enable
register write
0=not Quad
disable
Enable
Non-volatile Non-volatile
bit
bit
bit5
BP3
(level of
protected
block)
bit4
BP2
(level of
protected
block)
bit3
BP1
(level of
protected
block)
bit2
BP0
(level of
protected
block)
(note 1)
(note 1)
(note 1)
(note 1)
Non-volatile
bit
Non-volatile
bit
Non-volatile
bit
Non-volatile
bit
bit1
bit0
WEL
WIP
(write enable
(write in
latch)
progress bit)
1=write
1=write
enable
operation
0=not write 0=not in write
enable
operation
volatile bit
volatile bit
Note: see the "Table 2. Protected Area Sizes".
P/N: PM1772
17
REV. 2.0, AUG. 02, 2012
MX25L6436E
(5) Write Status Register (WRSR)
The WRSR instruction is for changing the values of Status Register Bits. Before sending WRSR instruction, the
Write Enable (WREN) instruction must be decoded and executed to set the Write Enable Latch (WEL) bit in advance. The WRSR instruction can change the value of Block Protect (BP3, BP2, BP1, BP0) bits to define the protected area of memory (as shown in Table 2). The WRSR also can set or reset the Quad enable (QE) bit and set or
reset the Status Register Write Disable (SRWD) bit in accordance with Write Protection (WP#/SIO2) pin signal, but
has no effect on bit1(WEL) and bit0 (WIP) of the status register. The WRSR instruction cannot be executed once the
Hardware Protected Mode (HPM) is entered.
The sequence of issuing WRSR instruction is: CS# goes low→ sending WRSR instruction code→ Status Register
data on SI→ CS# goes high. (Please refer to Figure 14)
The CS# must go high exactly at the byte boundary; otherwise, the instruction will be rejected and not executed.
The self-timed Write Status Register cycle time (tW) is initiated as soon as Chip Select (CS#) goes high. The Write
in Progress (WIP) bit still can be check out during the Write Status Register cycle is in progress. The WIP sets 1
during the tW timing, and sets 0 when Write Status Register Cycle is completed, and the Write Enable Latch (WEL)
bit is reset.
Protection Modes
Mode
Software protection
mode(SPM)
Hardware protection
mode (HPM)
Status register condition
WP# and SRWD bit status
Memory
Status register can be written
in (WEL bit is set to "1") and
the SRWD, BP0-BP3
bits can be changed
WP#=1 and SRWD bit=0, or
WP#=0 and SRWD bit=0, or
WP#=1 and SRWD=1
The protected area
cannot
be program or erase.
The SRWD, BP0-BP3 of
status register bits cannot be
changed
WP#=0, SRWD bit=1
The protected area
cannot
be program or erase.
Note: As defined by the values in the Block Protect (BP3, BP2, BP1, BP0) bits of the Status Register, as shown in Table 2.
As the table above showing, the summary of the Software Protected Mode (SPM) and Hardware Protected Mode (HPM):
Software Protected Mode (SPM):
- When SRWD bit=0, no matter WP#/SIO2 is low or high, the WREN instruction may set the WEL bit and can
change the values of SRWD, BP3, BP2, BP1, BP0. The protected area, which is defined by BP3, BP2, BP1,
BP0, is at software protected mode (SPM).
- When SRWD bit=1 and WP#/SIO2 is high, the WREN instruction may set the WEL bit can change the values of
SRWD, BP3, BP2, BP1, BP0. The protected area, which is defined by BP3, BP2, BP1, BP0, is at software protected mode (SPM)
Hardware Protected Mode (HPM):
- When SRWD bit=1, and then WP#/SIO2 is low (or WP#/SIO2 is low before SRWD bit=1), it enters the hardware
protected mode (HPM). The data of the protected area is protected by software protected mode by BP3, BP2,
BP1, BP0 and hardware protected mode by the WP#/SIO2 to against data modification.
Note:
To exit the hardware protected mode requires WP#/SIO2 driving high once the hardware protected mode is entered.
If the WP#/SIO2 pin is permanently connected to high, the hardware protected mode can never be entered; only
can use software protected mode via BP3, BP2, BP1, BP0.
If the system goes into four I/O mode, the feature of HPM will be disabled.
P/N: PM1772
18
REV. 2.0, AUG. 02, 2012
MX25L6436E
(6) Read Data Bytes (READ)
The read instruction is for reading data out. The address is latched on rising edge of SCLK, and data shifts out on
the falling edge of SCLK at a maximum frequency fR. The first address byte can be at any location. The address
is automatically increased to the next higher address after each byte data is shifted out, so the whole memory can
be read out at a single READ instruction. The address counter rolls over to 0 when the highest address has been
reached.
The sequence of issuing READ instruction is: CS# goes low→ sending READ instruction code→3-byte address on
SI →data out on SO→ to end READ operation can use CS# to high at any time during data out. (Please refer to Figure 15)
(7) Read Data Bytes at Higher Speed (FAST_READ)
The FAST_READ instruction is for quickly reading data out. The address is latched on rising edge of SCLK, and
data of each bit shifts out on the falling edge of SCLK at a maximum frequency fC. The first address byte can be at
any location. The address is automatically increased to the next higher address after each byte data is shifted out,
so the whole memory can be read out at a single FAST_READ instruction. The address counter rolls over to 0 when
the highest address has been reached.
The sequence of issuing FAST_READ instruction is: CS# goes low→sending FAST_READ instruction code→3-byte
address on SI→ 1-dummy byte (default) address on SI→data out on SO→ to end FAST_READ operation can use
CS# to high at any time during data out. (Please refer to Figure 16)
While Program/Erase/Write Status Register cycle is in progress, FAST_READ instruction is rejected without any impact on the Program/Erase/Write Status Register current cycle.
(8) Dual Read Mode (DREAD)
The DREAD instruction enable double throughput of Serial Flash in read mode. The address is latched on rising
edge of SCLK, and data of every two bits (interleave on 2 I/O pins) shift out on the falling edge of SCLK at a maximum frequency fT. The first address byte can be at any location. The address is automatically increased to the next
higher address after each byte data is shifted out, so the whole memory can be read out at a single DREAD instruction. The address counter rolls over to 0 when the highest address has been reached. Once writing DREAD instruction, the following data out will perform as 2-bit instead of previous 1-bit.
The sequence of issuing DREAD instruction is: CS# goes low → sending DREAD instruction → 3-byte address on
SI → 8-bit dummy cycle → data out interleave on SO1 & SO0 → to end DREAD operation can use CS# to high at
any time during data out (Please refer to Figure 17).
While Program/Erase/Write Status Register cycle is in progress, DREAD instruction is rejected without any impact
on the Program/Erase/Write Status Register current cycle.
(9) Quad Read Mode (QREAD)
The QREAD instruction enable quad throughput of Serial Flash in read mode. The address is latched on rising edge
of SCLK, and data of every four bits (interleave on 4 I/O pins) shift out on the falling edge of SCLK at a maximum
frequency fQ. The first address byte can be at any location. The address is automatically increased to the next high-
P/N: PM1772
19
REV. 2.0, AUG. 02, 2012
MX25L6436E
er address after each byte data is shifted out, so the whole memory can be read out at a single QREAD instruction.
The address counter rolls over to 0 when the highest address has been reached. Once writing QREAD instruction,
the following data out will perform as 4-bit instead of previous 1-bit.
The sequence of issuing QREAD instruction is: CS# goes low→ sending QREAD instruction → 3-byte address on
SI → 8-bit dummy cycle → data out interleave on SO3, SO2, SO1 & SO0→ to end QREAD operation can use
CS# to high at any time during data out (Please refer to Figure 18).
While Program/Erase/Write Status Register cycle is in progress, QREAD instruction is rejected without any impact
on the Program/Erase/Write Status Register current cycle.
(10) Sector Erase (SE)
The Sector Erase (SE) instruction is for erasing the data of the chosen sector to be "1". The instruction is used for
any 4K-byte sector. A Write Enable (WREN) instruction must execute to set the Write Enable Latch (WEL) bit before
sending the Sector Erase (SE). Any address of the sector (see Table 4) is a valid address for Sector Erase (SE) instruction. The CS# must go high exactly at the byte boundary (the least significant bit of the address been latchedin); otherwise, the instruction will be rejected and not executed.
The sequence of issuing SE instruction is: CS# goes low → sending SE instruction code→ 3-byte address on SI
→CS# goes high. (Please refer to Figure 19)
The self-timed Sector Erase Cycle time (tSE) is initiated as soon as Chip Select (CS#) goes high. The Write in
Progress (WIP) bit still can be checked while the Sector Erase cycle is in progress. The WIP sets during the tSE
timing, and clears when Sector Erase Cycle is completed, and the Write Enable Latch (WEL) bit is cleared. If the
sector is protected by BP3~0 (WPSEL=0) or by individual lock (WPSEL=1), the array data will be protected (no
change) and the WEL bit still be reset.
(11) Block Erase (BE)
The Block Erase (BE) instruction is for erasing the data of the chosen block to be "1". The instruction is used for
64K-byte block erase operation. A Write Enable (WREN) instruction must be executed to set the Write Enable Latch
(WEL) bit before sending the Block Erase (BE). Any address of the block (see Table 4) is a valid address for Block
Erase (BE) instruction. The CS# must go high exactly at the byte boundary (the least significant bit of address byte
been latched-in); otherwise, the instruction will be rejected and not executed.
The sequence of issuing BE instruction is: CS# goes low → sending BE instruction code → 3-byte address on SI
→ CS# goes high. (Please refer to Figure 20)
The self-timed Block Erase Cycle time (tBE) is initiated as soon as Chip Select (CS#) goes high. The Write in
Progress (WIP) bit still can be checked while the Block Erase cycle is in progress. The WIP sets during the tBE timing, and clears when Block Erase Cycle is completed, and the Write Enable Latch (WEL) bit is cleared. If the block
is protected by BP3~0 (WPSEL=0) or by individual lock (WPSEL=1), the array data will be protected (no change)
and the WEL bit still be reset.
(12) Block Erase (BE32K)
The Block Erase (BE32) instruction is for erasing the data of the chosen block to be "1". The instruction is used
for 32K-byte block erase operation. A Write Enable (WREN) instruction must be executed to set the Write Enable
P/N: PM1772
20
REV. 2.0, AUG. 02, 2012
MX25L6436E
Latch (WEL) bit before sending the Block Erase (BE32). Any address of the block (see Table 4) is a valid address
for Block Erase (BE32) instruction. The CS# must go high exactly at the byte boundary (the least significant bit of
address byte been latched-in); otherwise, the instruction will be rejected and not executed.
The sequence of issuing BE32 instruction is: CS# goes low → sending BE32 instruction code → 3-byte address on
SI → CS# goes high. (Please refer to Figure 20)
The self-timed Block Erase Cycle time (tBE) is initiated as soon as Chip Select (CS#) goes high. The Write in
Progress (WIP) bit still can be checked while the Block Erase cycle is in progress. The WIP sets during the tBE timing, and clears when Block Erase Cycle is completed, and the Write Enable Latch (WEL) bit is cleared. If the block
is protected by BP3~0 (WPSEL=0) or by individual lock (WPSEL=1), the array data will be protected (no change)
and the WEL bit still be reset.
(13) Chip Erase (CE)
The Chip Erase (CE) instruction is for erasing the data of the whole chip to be "1". A Write Enable (WREN) instruction must be executed to set the Write Enable Latch (WEL) bit before sending the Chip Erase (CE). The CS# must
go high exactly at the byte boundary; otherwise, the instruction will be rejected and not executed.
The sequence of issuing CE instruction is: CS# goes low → sending CE instruction code → CS# goes high. (Please
refer to Figure 21)
The self-timed Chip Erase Cycle time (tCE) is initiated as soon as Chip Select (CS#) goes high. The Write in
Progress (WIP) bit still can be checked while the Chip Erase cycle is in progress. The WIP sets during the tCE timing, and clears when Chip Erase Cycle is completed, and the Write Enable Latch (WEL) bit is cleared. If the chip is
protected, the Chip Erase (CE) instruction will not be executed, but WEL will be reset.
(14) Page Program (PP)
The Page Program (PP) instruction is for programming the memory to be "0". A Write Enable (WREN) instruction
must be executed to set the Write Enable Latch (WEL) bit before sending the Page Program (PP). The device
programs only the last 256 data bytes sent to the device. If the entire 256 data bytes are going to be programmed,
A7-A0 (the eight least significant address bits) should be set to 0. If the eight least significant address bits (A7-A0)
are not all 0, all transmitted data going beyond the end of the current page are programmed from the start address
of the same page (from the address A7-A0 are all 0). If more than 256 bytes are sent to the device, the data of the
last 256-byte is programmed at the requested page and previous data will be disregarded. If less than 256 bytes
are sent to the device, the data is programmed at the requested address of the page without effect on other address
of the same page.
The sequence of issuing PP instruction is: CS# goes low→ sending PP instruction code→ 3-byte address on SI→ at
least 1-byte on data on SI→ CS# goes high. (Please refer to Figure 22)
The CS# must be kept to low during the whole Page Program cycle; The CS# must go high exactly at the byte
boundary( the latest eighth bit of data being latched in), otherwise, the instruction will be rejected and will not be
executed.
The self-timed Page Program Cycle time (tPP) is initiated as soon as Chip Select (CS#) goes high. The Write in
Progress (WIP) bit still can be checked while the Page Program cycle is in progress. The WIP sets during the tPP
timing, and clears when Page Program Cycle is completed, and the Write Enable Latch (WEL) bit is cleared. If
the page is protected by BP3~0 (WPSEL=0) or by individual lock (WPSEL=1), the array data will be protected (no
P/N: PM1772
21
REV. 2.0, AUG. 02, 2012
MX25L6436E
change) and the WEL bit will still be reset.
(15) 4 x I/O Page Program (4PP)
The Quad Page Program (4PP) instruction is for programming the memory to be "0". A Write Enable (WREN)
instruction must be executed to set the Write Enable Latch (WEL) bit and Quad Enable (QE) bit must be set to "1"
before sending the Quad Page Program (4PP). The Quad Page Programming takes four pins: SIO0, SIO1, SIO2,
and SIO3, which can raise programer performance and and the effectiveness of application of lower clock less
than 20MHz. For system with faster clock, the Quad page program cannot provide more performance, because
the required internal page program time is far more than the time data flows in. Therefore, we suggest that while
executing this command (especially during sending data), user can slow the clock speed down to 20MHz below.
The other function descriptions are as same as standard page program.
The sequence of issuing 4PP instruction is: CS# goes low→ sending 4PP instruction code→ 3-byte address on
SIO[3:0]→ at least 1-byte on data on SIO[3:0]→ CS# goes high. (Please refer to Figure 23)
If the page is protected by BP3~0 (WPSEL=0) or by individual lock (WPSEL=1), the array data will be protected (no
change) and the WEL bit will still be reset.
P/N: PM1772
22
REV. 2.0, AUG. 02, 2012
MX25L6436E
The Program/Erase function instruction function flow is as follows:
Program/Erase Flow(1) with read array data
Start
WREN command
RDSR command*
WREN=1?
No
Yes
Program/erase command
Write program data/address
(Write erase address)
RDSR command
No
WIP=0?
Yes
Read array data
(same address of PGM/ERS)
Verify OK?
No
Yes
Program/erase fail
Program/erase successfully
CLSR(30h) command
Program/erase
another block?
No
Yes
*
* Issue RDSR to check BP[3:0].
* If WPSEL=1, issue RDBLOCK to check the block status.
Program/erase completed
P/N: PM1772
23
REV. 2.0, AUG. 02, 2012
MX25L6436E
Program/Erase Flow(2) without read array data
Start
WREN command
RDSR command*
WREN=1?
No
Yes
Program/erase command
Write program data/address
(Write erase address)
RDSR command
No
WIP=0?
Yes
RDSCUR command
P_FAIL/E_FAIL=1?
Yes
No
Program/erase fail
Program/erase successfully
CLSR(30h) command
Program/erase
Yes
another block?
No
* Issue RDSR to check BP[3:0].
* If WPSEL=1, issue RDBLOCK to check the block status.
Program/erase completed
P/N: PM1772
24
REV. 2.0, AUG. 02, 2012
MX25L6436E
(16) Continuously program mode (CP mode)
The CP mode may enhance program performance by automatically increasing address to the next higher address
after each byte data has been programmed.
The Continuously program (CP) instruction is for multiple byte program to Flash. A write Enable (WREN) instruction
must execute to set the Write Enable Latch (WEL) bit before sending the Continuously program (CP) instruction.
CS# requires to go high before CP instruction is executing. After CP instruction and address input, two bytes of
data is input sequentially from MSB(bit7) to LSB(bit0). The first byte data will be programmed to the initial address
range with A0=0 and second byte data with A0=1. If only one byte data is input, the CP mode will not process. If
more than two bytes data are input, the additional data will be ignored and only two byte data are valid. Any byte to
be programmed should be in the erase state (FF) first. It will not roll over during the CP mode, once the last unprotected address has been reached, the chip will exit CP mode and reset write Enable Latch bit (WEL) as "0" and CP
mode bit as "0". Please check the WIP bit status if it is not in write progress before entering next valid instruction.
During CP mode, the valid commands are CP command (AD hex), WRDI command (04 hex), RDSR command (05
hex), and RDSCUR command (2B hex). And the WRDI command is valid after completion of a CP programming cycle, which means the WIP bit=0.
The sequence of issuing CP instruction is : CS# goes low → sending CP instruction code → 3-byte address on SI
pin → two data bytes on SI → CS# goes high to low → sending CP instruction and then continue two data bytes
are programmed → CS# goes high to low → till last desired two data bytes are programmed → CS# goes high to
low →sending WRDI (Write Disable) instruction to end CP mode → send RDSR instruction to verify if CP mode
word program ends, or send RDSCUR to check bit4 to verify if CP mode ends. (Please refer to Figure 24)
Two methods to detect the completion of a program cycle during CP mode:
1) Software method-I: by checking WIP bit of Status Register to detect the completion of CP mode.
2) Software method-II: by waiting for a tBP time out to determine if it may load next valid command or not.
3) Hardware method: by writing ESRY (enable SO to output RY/BY#) instruction to detect the completion of a
program cycle during CP mode. The ESRY instruction must be executed before CP mode execution. Once it is
enable in CP mode, the CS# goes low will drive out the RY/BY# status on SO, "0" indicates busy stage, "1" indicates ready stage, SO pin outputs tri-state if CS# goes high. DSRY (disable SO to output RY/BY#) instruction to
disable the SO to output RY/BY# and return to status register data output during CP mode. Please note that the
ESRY/DSRY command are not accepted unless the completion of CP mode.
If the page is protected by BP3~0 (WPSEL=0) or by individual lock (WPSEL=1), the array data will be protected (no
change) and the WEL bit will still be reset.
P/N: PM1772
25
REV. 2.0, AUG. 02, 2012
MX25L6436E
(17) Deep Power-down (DP)
The Deep Power-down (DP) instruction is for setting the device to minimum power consumption (the standby current is reduced from ISB1 to ISB2). The Deep Power-down mode requires the Deep Power-down (DP) instruction
to enter, during the Deep Power-down mode, the device is not active and all Write/Program/Erase instruction are
ignored.
The sequence of issuing DP instruction is: CS# goes low→ sending DP instruction code→ CS# goes high. (Please
refer to Figure 25)
Once the DP instruction is set, all instruction will be ignored except the Release from Deep Power-down mode (RDP)
and Read Electronic Signature (RES) instruction. (those instructions allow the ID being reading out). When Powerdown, the deep power-down mode automatically stops, and when power-up, the device automatically is in standby
mode. For RDP instruction the CS# must go high exactly at the byte boundary (the latest eighth bit of instruction
code been latched-in); otherwise, the instruction will not executed. As soon as Chip Select (CS#) goes high, a delay
of tDP is required before entering the Deep Power-down mode and reducing the current to ISB2.
(18) Release from Deep Power-down (RDP), Read Electronic Signature (RES)
The Release from Deep Power-down (RDP) instruction is completed by driving Chip Select (CS#) High. When Chip
Select (CS#) is driven High, the device is put in the Standby Power mode. If the device was not previously in the
Deep Power-down mode, the transition to the standby Power mode is immediate. If the device was previously in the
Deep Power-down mode, though, the transition to the standby Power mode is delayed by tRES2, and Chip Select (CS#)
must remain High for at least tRES2(max), as specified in Table 11. Once in the standby mode, the device waits to
be selected, so that it can receive, decode and execute instructions.
RES instruction is for reading out the old style of 8-bit Electronic Signature, whose values are shown as table of
ID Definitions. This is not the same as RDID instruction. It is not recommended to use for new design. For new
design, please use RDID instruction. Even in Deep power-down mode, the RDP and RES are also allowed to be
executed, only except the device is in progress of program/erase/write cycles; there's no effect on the current program/erase/write cycles in progress. The sequence is shown as Figure 26, Figure 27.
The RES instruction is ended by CS# goes high after the ID been read out at least once. The ID outputs repeatedly if continuously send the additional clock cycles on SCLK while CS# is at low. If the device was not previously
in Deep Power-down mode, the device transition to standby mode is immediate. If the device was previously in
Deep Power-down mode, there's a delay of tRES2 to transit to standby mode, and CS# must remain to high at
least tRES2(max). Once in the standby mode, the device waits to be selected, so it can be receive, decode, and
execute instruction.
The RDP instruction is for releasing from Deep Power-down Mode.
(19) Read Electronic Manufacturer ID & Device ID (REMS), (REMS2), (REMS4)
The REMS, REMS2 and REMS4 instruction provides both the JEDEC assigned Manufacturer ID and the specific
Device ID.
The instruction is initiated by driving the CS# pin low and shift the instruction code "90h", "DFh" or "EFh" followed
by two dummy bytes and one bytes address (A7~A0). After which, the Manufacturer ID for MXIC (C2h) and the Device ID are shifted out on the falling edge of SCLK with most significant bit (MSB) first as shown in Figure 34. The
Device ID values are listed in table of ID Definitions. If the one-byte address is initially set to 01h, then the Device
ID will be read first and then followed by the Manufacturer ID. The Manufacturer and Device IDs can be read continuously, alternating from one to the other. The instruction is completed by driving CS# high.
P/N: PM1772
26
REV. 2.0, AUG. 02, 2012
MX25L6436E
Table 6. ID Definitions
Command Type
RDID
MX25L6436E
memory type
20
electronic ID
16
device ID
16
manufacturer ID
C2
RES
REMS/REMS2/REMS4
manufacturer ID
C2
memory density
17
(20) Enter Secured OTP (ENSO)
The ENSO instruction is for entering the additional 4K-bit Secured OTP mode. While device is in 4K-bit Secured
OTP mode, main array access is not available. The additional 4K-bit Secured OTP is independent from main array,
and may be used to store unique serial number for system identifier. After entering the Secured OTP mode, follow
standard read or program procedure to read out the data or update data. The Secured OTP data cannot be updated again once it is lock-down.
The sequence of issuing ENSO instruction is: CS# goes low→ sending ENSO instruction to enter Secured OTP
mode→ CS# goes high.
Please note that WRSR/WRSCUR/WPSEL/SBLK/GBLK/SBULK/GBULK/CE/BE/SE/BE32K commands are not acceptable during the access of secure OTP region, once Security OTP is lock down, only read related commands
are valid.
(21) Exit Secured OTP (EXSO)
The EXSO instruction is for exiting the additional 4K-bit Secured OTP mode.
The sequence of issuing EXSO instruction is: CS# goes low→ sending EXSO instruction to exit Secured OTP
mode→ CS# goes high.
(22) Read Security Register (RDSCUR)
The RDSCUR instruction is for reading the value of Security Register. The Read Security Register can be read at
any time (even in program/erase/write status register/write security register condition) and continuously.
The sequence of issuing RDSCUR instruction is : CS# goes low→ sending RDSCUR instruction → Security Register data out on SO→ CS# goes high.
The definition of the Security Register is as below:
Secured OTP Indicator bit. The Secured OTP indicator bit shows the chip is locked by factory before ex- factory
or not. When it is "0", it indicates non-factory lock; "1" indicates factory- lock.
Lock-down Secured OTP (LDSO) bit. By writing WRSCUR instruction, the LDSO bit may be set to "1" for customer lock-down purpose. However, once the bit is set to "1" (lock-down), the LDSO bit and the 4K-bit Secured
OTP area cannot be updated any more.
P/N: PM1772
27
REV. 2.0, AUG. 02, 2012
MX25L6436E
Continuously Program Mode (CP mode) bit. The Continuously Program Mode bit indicates the status of CP
mode, "0" indicates not in CP mode; "1" indicates in CP mode.
Program Fail Flag bit. If the program operation fails on a protected memory region or locked OTP region, this bit
will also be set. This bit can be the failure indication of one or more program operations. This fail flag bit will be reset
by command CLSR (30h).
Erase Fail Flag bit. If the erase operation fails on a protected memory region or locked OTP region, this bit will also
be set. This bit can be the failure indication of one or more erase operations. This fail flag bit will be reset by command CLSR (30h).
Write Protection Select bit. The Write Protection Select bit indicates that WPSEL has been executed successfully.
Once this bit has been set (WPSEL=1), all the blocks or sectors will be write-protected after the power-on every
time. Once WPSEL has been set, it cannot be changed again, which means it's only for individual WP mode.
Under the individual block protection mode (WPSEL=1), hardware protection is performed by driving WP#=0. Once
WP#=0 all array blocks/sectors are protected regardless of the contents of SRAM lock bits.
Security Register Definition
bit7
bit6
bit5
bit4
Continuously
Program
mode
(CP mode)
bit3
x
bit2
x
bit1
bit0
LDSO
(lock-down
4K-bit
4K-bit Se- Secured OTP
cured OTP)
WPSEL
E_FAIL
P_FAIL
0=normal
WP mode
1=individual
WP mode
(default=0)
0=normal
Erase
succeed
1=indicate
Erase failed
(default=0)
0=normal
Program
succeed
1=indicate
Program
failed
(default=0)
0=normal
Program
mode
1=CP mode
(default=0)
reserved
reserved
0 = not
lockdown
1 = lockdown
(cannot
program/
erase
OTP)
non-volatile
bit
volatile bit
volatile bit
volatile bit
volatile bit
volatile bit
non-volatile
bit
non-volatile
bit
OTP
Read Only
Read Only
Read Only
Read Only
Read Only
OTP
Read Only
0=
nonfactory
lock
1 = factory
lock
(23) Write Security Register (WRSCUR)
The WRSCUR instruction is for changing the values of Security Register Bits. Unlike write status register, the WREN
instruction is not required before sending WRSCUR instruction. The WRSCUR instruction may change the values
of bit1 (LDSO bit) for customer to lock-down the 4K-bit Secured OTP area. Once the LDSO bit is set to "1", the Secured OTP area cannot be updated any more.
The sequence of issuing WRSCUR instruction is :CS# goes low→ sending WRSCUR instruction → CS# goes high.
The CS# must go high exactly at the boundary; otherwise, the instruction will be rejected and not executed.
P/N: PM1772
28
REV. 2.0, AUG. 02, 2012
MX25L6436E
(24) Write Protection Selection (WPSEL)
There are two write protection methods, (1) BP protection mode (2) individual block protection mode. If WPSEL=0,
flash is under BP protection mode . If WPSEL=1, flash is under individual block protection mode. The default value
of WPSEL is “0”. WPSEL command can be used to set WPSEL=1. Please note that WPSEL is an OTP bit. Once
WPSEL is set to 1, there is no chance to recovery WPSEL back to “0”. If the flash is put on BP mode, the individual block protection mode is disabled. Contrarily, if flash is on the individual block protection mode, the BP mode
is disabled.
Every time after the system is powered-on the Security Register bit 7 is checked. If WPSEL=1, all the blocks
and sectors will be write protected by default. User may only unlock the blocks or sectors via SBULK and
GBULK instructions. Program or erase functions can only be operated after the Unlock instruction is executed.
BP protection mode, WPSEL=0:
ARRAY is protected by BP3~BP0 and BP3~BP0 bits are protected by “SRWD=1 and WP#=0”, where SRWD is bit 7
of status register that can be set by WRSR command.
Individual block protection mode, WPSEL=1:
Blocks are individually protected by their own SRAM lock bits which are set to “1” after power up. SBULK and SBLK
command can set SRAM lock bit to “0” and “1”. When the system accepts and executes WPSEL instruction, bit 7 in
the security register will be set. It will activate SBLK, SBULK, RDBLOCK, GBLK, GBULK etc instructions to conduct
block lock protection and replace the original Software Protect Mode (SPM) use (BP3~BP0) indicated block methods. Under the individual block protection mode (WPSEL=1), hardware protection is performed by driving WP#=0.
Once WP#=0 all array blocks/sectors are protected regardless of the contents of SRAM lock bits.
The sequence of issuing WPSEL instruction is: CS# goes low → sending WPSEL instruction to enter the individual
block protect mode → CS# goes high.
WPSEL instruction function flow is as follows:
BP and SRWD if WPSEL=0
WP# pin
BP3
BP2
BP1
BP0
SRWD
64KB
64KB
64KB
(1) BP3~BP0 is used to define the protection group region.
(The protected area size see Table 2)
(2) “SRWD=1 and WP#=0” is used to protect BP3~BP0. In this
case, SRWD and BP3~BP0 of status register bits can not
be changed by WRSR
.
.
.
64KB
P/N: PM1772
29
REV. 2.0, AUG. 02, 2012
MX25L6436E
The individual block lock mode is effective after setting WPSEL=1
SRAM
SRAM
…
…
TOP 4KBx16
Sectors
4KB
4KB
4KB
SRAM
SRAM
…
64KB
SRAM
…
……
Uniform
64KB blocks
64KB
4KB
SRAM
…
…
Bottom
4KBx16
Sectors
4KB
SRAM
• Power-Up: All SRAM bits=1 (all blocks are default protected).
All array cannot be programmed/erased
• SBLK/SBULK(36h/39h):
- SBLK(36h): Set SRAM bit=1 (protect): array can not be programmed/erased
- SBULK(39h): Set SRAM bit=0 (unprotect): array can be programmed/erased
- All the top 4KBx16 sectors and bottom 4KBx16 sectors and other 64KB uniform blocks can be protected and unprotected with SRAM bits individually by SBLK/SBULK command set.
• GBLK/ GBULK(7Eh/98h):
- GBLK(7Eh): Set all SRAM bits=1, the whole chip is protected and cannot be programmed/erased.
- GBULK(98h): Set all SRAM bits=0, the whole chip is unprotected and can be programmed/erased.
- All sectors and blocks SRAM bits of the whole chip can be
protected and unprotected at one time by GBLK/GBULK command set.
• RDBLOCK(3Ch):
- use RDBLOCK mode to check the SRAM bits status after SBULK/SBLK/GBULK/GBLK command set.
SBULK / SBLK / GBULK / GBLK / RDBLOCK
P/N: PM1772
30
REV. 2.0, AUG. 02, 2012
MX25L6436E
WPSEL Flow
start
RDSCUR(2Bh) command
Yes
WPSEL=1?
No
WPSEL disable,
block protected by BP[3:0]
WPSEL(68h) command
RDSR command
WIP=0?
No
Yes
RDSCUR(2Bh) command
WPSEL=1?
No
Yes
WPSEL set successfully
WPSEL set fail
WPSEL enable.
Block protected by individual lock
(SBLK, SBULK, … etc).
P/N: PM1772
31
REV. 2.0, AUG. 02, 2012
MX25L6436E
(25) Single Block Lock/Unlock Protection (SBLK/SBULK)
These instructions are only effective after WPSEL was executed. The SBLK instruction is for write protection a specified block(or sector) of memory, using A23-A16 or (A23-A12) address bits to assign a 64Kbyte block (or 4K bytes
sector) to be protected as read only. The SBULK instruction will cancel the block (or sector) write protection state.
This feature allows user to stop protecting the entire block (or sector) through the chip unprotect command (GBULK).
The WREN (Write Enable) instruction is required before issuing SBLK/SBULK instruction.
The sequence of issuing SBLK/SBULK instruction is: CS# goes low → send SBLK/SBULK (36h/39h) instruction →
send 3 address bytes assign one block (or sector) to be protected on SI pin → CS# goes high. (Please refer to Figure 30)
The CS# must go high exactly at the byte boundary, otherwise the instruction will be rejected and not be executed.
SBLK/SBULK instruction function flow is as follows:
Block Lock Flow
Start
RDSCUR(2Bh) command
WPSEL=1?
No
WPSEL command
Yes
WREN command
SBLK command
( 36h + 24bit address )
RDSR command
WIP=0?
No
Yes
RDBLOCK command
( 3Ch + 24bit address )
Data = FFh ?
No
Yes
Block lock successfully
Lock another block?
Block lock fail
Yes
No
Block lock completed
P/N: PM1772
32
REV. 2.0, AUG. 02, 2012
MX25L6436E
Block Unlock Flow
start
RDSCUR(2Bh) command
WPSEL=1?
No
WPSEL command
Yes
WREN command
SBULK command
( 39h + 24bit address )
RDSR command
No
WIP=0?
Yes
Unlock another block?
Yes
Unlock block completed?
P/N: PM1772
33
REV. 2.0, AUG. 02, 2012
MX25L6436E
(26) Read Block Lock Status (RDBLOCK)
This instruction is only effective after WPSEL was executed. The RDBLOCK instruction is for reading the status of
protection lock of a specified block (or sector), using A23-A16 (or A23-A12) address bits to assign a 64K bytes block (4K
bytes sector) and read protection lock status bit which the first byte of Read-out cycle. The status bit is"1" to indicate
that this block has be protected, that user can read only but cannot write/program /erase this block. The status bit is
"0" to indicate that this block hasn't be protected, and user can read and write this block.
The sequence of issuing RDBLOCK instruction is: CS# goes low → send RDBLOCK (3Ch) instruction → send 3 address bytes to assign one block on SI pin → read block's protection lock status bit on SO pin → CS# goes high. (Please
refer to Figure 31)
(27) Gang Block Lock/Unlock (GBLK/GBULK)
These instructions are only effective after WPSEL was executed. The GBLK/GBULK instruction is for enable/disable
the lock protection block of the whole chip.
The WREN (Write Enable) instruction is required before issuing GBLK/GBULK instruction.
The sequence of issuing GBLK/GBULK instruction is: CS# goes low → send GBLK/GBULK (7Eh/98h) instruction →
CS# goes high. (Please refer to Figure 32)
The CS# must go high exactly at the byte boundary, otherwise, the instruction will be rejected and not be executed.
(28) Clear SR Fail Flags (CLSR)
The CLSR instruction is for resetting the Program/Erase Fail Flag bit of Security Register. It should be executed before program/erase another block during programming/erasing flow without read array data.
The sequence of issuing CLSR instruction is: CS# goes low → send CLSR instruction code → CS# goes high.
The CS# must go high exactly at the byte boundary; otherwise, the instruction will be rejected and not executed.
(29) Enable SO to Output RY/BY# (ESRY)
The ESRY instruction is for outputting the ready/busy status to SO during CP mode.
The sequence of issuing ESRY instruction is: CS# goes low → sending ESRY instruction code → CS# goes high.
The CS# must go high exactly at the byte boundary; otherwise, the instruction will be rejected and not executed.
(30) Disable SO to Output RY/BY# (DSRY)
The DSRY instruction is for resetting ESRY during CP mode. The ready/busy status will not output to SO after
DSRY issued.
The sequence of issuing DSRY instruction is: CS# goes low → send DSRY instruction code → CS# goes high.
The CS# must go high exactly at the byte boundary; otherwise, the instruction will be rejected and not executed.
P/N: PM1772
34
REV. 2.0, AUG. 02, 2012
MX25L6436E
(31) Read SFDP Mode (RDSFDP)
The Serial Flash Discoverable Parameter (SFDP) standard provides a consistent method of describing the functional
and feature capabilities of serial flash devices in a standard set of internal parameter tables. These parameter tables
can be interrogated by host system software to enable adjustments needed to accommodate divergent features
from multiple vendors. The concept is similar to the one found in the Introduction of JEDEC Standard, JESD68 on
CFI.
The sequence of issuing RDSFDP instruction is CS# goes low→send RDSFDP instruction (5Ah)→send 3 address
bytes on SI pin→send 1 dummy byte on SI pin→read SFDP code on SO→to end RDSFDP operation can use CS#
to high at any time during data out.
SFDP is a JEDEC Standard, JESD216.
Read Serial Flash Discoverable Parameter (RDSFDP) Sequence
CS#
0
1
2
3
4
5
6
7
8
9 10
28 29 30 31
SCLK
Command
SI
SO
24 BIT ADDRESS
23 22 21
5Ah
3
2
1
0
High-Z
CS#
32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47
SCLK
Dummy Cycle
SI
7
6
5
4
3
2
1
0
DATA OUT 2
DATA OUT 1
SO
7
6
5
3
2
1
0
7
MSB
MSB
P/N: PM1772
4
35
6
5
4
3
2
1
0
7
MSB
REV. 2.0, AUG. 02, 2012
MX25L6436E
Table 7. Signature and Parameter Identification Data Values
Description
SFDP Signature
Comment
Fixed: 50444653h
Add (h) DW Add Data (h/b)
(Byte)
(Bit)
(Note1)
00h
07:00
53h
Data
(h)
53h
01h
15:08
46h
46h
02h
23:16
44h
44h
03h
31:24
50h
50h
SFDP Minor Revision Number
Start from 00h
04h
07:00
00h
00h
SFDP Major Revision Number
Start from 01h
This number is 0-based. Therefore,
0 indicates 1 parameter header.
05h
15:08
01h
01h
06h
23:16
01h
01h
07h
31:24
FFh
FFh
00h: it indicates a JEDEC specified
header.
08h
07:00
00h
00h
Start from 00h
09h
15:08
00h
00h
Start from 01h
0Ah
23:16
01h
01h
How many DWORDs in the
Parameter table
0Bh
31:24
09h
09h
0Ch
07:00
30h
30h
0Dh
15:08
00h
00h
0Eh
23:16
00h
00h
0Fh
31:24
FFh
FFh
it indicates Macronix manufacturer
ID
10h
07:00
C2h
C2h
Start from 00h
11h
15:08
00h
00h
Start from 01h
12h
23:16
01h
01h
How many DWORDs in the
Parameter table
13h
31:24
04h
04h
14h
07:00
60h
60h
15h
15:08
00h
00h
16h
23:16
00h
00h
17h
31:24
FFh
FFh
Number of Parameter Headers
Unused
ID number (JEDEC)
Parameter Table Minor Revision
Number
Parameter Table Major Revision
Number
Parameter Table Length
(in double word)
Parameter Table Pointer (PTP)
First address of JEDEC Flash
Parameter table
Unused
ID number
(Macronix manufacturer ID)
Parameter Table Minor Revision
Number
Parameter Table Major Revision
Number
Parameter Table Length
(in double word)
Parameter Table Pointer (PTP)
First address of Macronix Flash
Parameter table
Unused
P/N: PM1772
36
REV. 2.0, AUG. 02, 2012
MX25L6436E
Table 8. Parameter Table (0): JEDEC Flash Parameter Tables
Description
Comment
Block/Sector Erase sizes
00: Reserved, 01: 4KB erase,
10: Reserved,
11: not suport 4KB erase
Write Granularity
0: 1Byte, 1: 64Byte or larger
Write Enable Instruction Required 0: not required
for Writing to Volatile Status
1: required 00h to be written to the
Registers
status register
Add (h) DW Add Data (h/b)
(Byte)
(Bit)
(Note1)
01b
02
1b
03
0b
30h
0: use 50h opcode,
1: use 06h opcode
Write Enable Opcode Select for
Note: If target flash status register is
Writing to Volatile Status Registers
nonvolatile, then bits 3 and 4 must
be set to 00b.
Contains 111b and can never be
Unused
changed
4KB Erase Opcode
01:00
31h
Data
(h)
E5h
04
0b
07:05
111b
15:08
20h
16
1b
18:17
00b
19
0b
20
0b
20h
(1-1-2) Fast Read (Note2)
0=not support 1=support
Address Bytes Number used in
addressing flash array
Double Transfer Rate (DTR)
Clocking
00: 3Byte only, 01: 3 or 4Byte,
10: 4Byte only, 11: Reserved
(1-2-2) Fast Read
0=not support 1=support
(1-4-4) Fast Read
0=not support 1=support
21
0b
(1-1-4) Fast Read
0=not support 1=support
22
1b
23
1b
33h
31:24
FFh
37h:34h
31:00
03FF FFFFh
0=not support 1=support
32h
Unused
Unused
Flash Memory Density
(1-4-4) Fast Read Number of Wait 0 0000b: Wait states (Dummy
states (Note3)
Clocks) not support
(1-4-4) Fast Read Number of
000b: Mode Bits not support
Mode Bits (Note4)
38h
(1-4-4) Fast Read Opcode
39h
(1-1-4) Fast Read Number of Wait 0 0000b: Wait states (Dummy
states
Clocks) not support
(1-1-4) Fast Read Number of
000b: Mode Bits not support
Mode Bits
3Ah
(1-1-4) Fast Read Opcode
3Bh
P/N: PM1772
37
04:00
0 0000b
07:05
000b
15:08
FFh
20:16
0 1000b
23:21
000b
31:24
6Bh
C1h
FFh
00h
FFh
08h
6Bh
REV. 2.0, AUG. 02, 2012
MX25L6436E
Description
Comment
(1-1-2) Fast Read Number of Wait 0 0000b: Wait states (Dummy
states
Clocks) not support
(1-1-2) Fast Read Number of
000b: Mode Bits not support
Mode Bits
Add (h) DW Add Data (h/b)
(Byte)
(Bit)
(Note1)
3Ch
(1-1-2) Fast Read Opcode
3Dh
(1-2-2) Fast Read Number of Wait 0 0000b: Wait states (Dummy
states
Clocks) not support
(1-2-2) Fast Read Number of
000b: Mode Bits not support
Mode Bits
3Eh
(1-2-2) Fast Read Opcode
3Fh
(2-2-2) Fast Read
0=not support 1=support
Unused
(4-4-4) Fast Read
0=not support 1=support
40h
Unused
04:00
0 1000b
07:05
000b
15:08
3Bh
20:16
0 0000b
23:21
000b
31:24
FFh
00
0b
03:01
111b
04
0b
07:05
111b
Data
(h)
08h
3Bh
00h
FFh
EEh
Unused
43h:41h
31:08
FFh
FFh
Unused
45h:44h
15:00
FFh
FFh
20:16
0 000b
23:21
000b
(2-2-2) Fast Read Number of Wait 0 0000b: Wait states (Dummy
states
Clocks) not support
(2-2-2) Fast Read Number of
000b: Mode Bits not support
Mode Bits
46h
(2-2-2) Fast Read Opcode
47h
31:24
FFh
FFh
49h:48h
15:00
FFh
FFh
20:16
0 0000b
23:21
000b
Unused
00h
(4-4-4) Fast Read Number of Wait 0 0000b: Wait states (Dummy
states
Clocks) not support
(4-4-4) Fast Read Number of
000b: Mode Bits not support
Mode Bits
4Ah
(4-4-4) Fast Read Opcode
4Bh
31:24
FFh
FFh
4Ch
07:00
0Ch
0Ch
4Dh
15:08
20h
20h
4Eh
23:16
0Fh
0Fh
4Fh
31:24
52h
52h
50h
07:00
10h
10h
51h
15:08
D8h
D8h
52h
23:16
00h
00h
53h
31:24
FFh
FFh
Sector Type 1 Size
Sector/block size = 2^N bytes (Note5)
0x00b: this sector type doesn't exist
Sector Type 1 erase Opcode
Sector Type 2 Size
Sector/block size = 2^N bytes
0x00b: this sector type doesn't exist
Sector Type 2 erase Opcode
Sector Type 3 Size
Sector/block size = 2^N bytes
0x00b: this sector type doesn't exist
Sector Type 3 erase Opcode
Sector Type 4 Size
Sector/block size = 2^N bytes
0x00b: this sector type doesn't exist
Sector Type 4 erase Opcode
P/N: PM1772
38
00h
REV. 2.0, AUG. 02, 2012
MX25L6436E
Table 9. Parameter Table (1): Macronix Flash Parameter Tables
Description
Comment
Add (h) DW Add Data (h/b)
(Byte)
(Bit)
(Note1)
Data
(h)
Vcc Supply Maximum Voltage
2000h=2.000V
2700h=2.700V
3600h=3.600V
61h:60h
07:00
15:08
00h
36h
00h
36h
Vcc Supply Minimum Voltage
1650h=1.650V
2250h=2.250V
2350h=2.350V
2700h=2.700V
63h:62h
23:16
31:24
00h
27h
00h
27h
H/W Reset# pin
0=not support 1=support
00
0b
H/W Hold# pin
0=not support 1=support
01
0b
Deep Power Down Mode
0=not support 1=support
02
1b
S/W Reset
0=not support 1=support
03
0b
S/W Reset Opcode
Reset Enable (66h) should be issued 65h:64h
before Reset Opcode
11:04
1111 1111b
(FFh)
Program Suspend/Resume
0=not support 1=support
12
0b
Erase Suspend/Resume
0=not support 1=support
13
0b
14
1b
15
0b
66h
23:16
FFh
FFh
67h
31:24
FFh
FFh
Unused
Wrap-Around Read mode
0=not support 1=support
Wrap-Around Read mode Opcode
Wrap-Around Read data length
08h:support 8B wrap-around read
16h:8B&16B
32h:8B&16B&32B
64h:8B&16B&32B&64B
Individual block lock
0=not support 1=support
00
1b
Individual block lock bit
(Volatile/Nonvolatile)
0=Volatile 1=Nonvolatile
01
0b
09:02
0011 0110b
(36h)
10
0b
11
1b
Individual block lock Opcode
4FF4h
Individual block lock Volatile
protect bit default protect status
0=protect 1=unprotect
Secured OTP
0=not support 1=support
Read Lock
0=not support 1=support
12
0b
Permanent Lock
0=not support 1=support
13
0b
Unused
15:14
11b
Unused
31:16
FFh
FFh
31:00
FFh
FFh
Unused
P/N: PM1772
6Bh:68h
6Fh:6Ch
39
C8D9h
REV. 2.0, AUG. 02, 2012
MX25L6436E
Note 1:h/b is hexadecimal or binary.
Note 2:(x-y-z) means I/O mode nomenclature used to indicate the number of active pins used for the opcode (x),
address (y), and data (z). At the present time, the only valid Read SFDP instruction modes are: (1-1-1), (2-2-2),
and (4-4-4)
Note 3:Wait States is required dummy clock cycles after the address bits or optional mode bits.
Note 4:Mode Bits is optional control bits that follow the address bits. These bits are driven by the system controller
if they are specified. (eg,read performance enhance toggling bits)
Note 5:4KB=2^0Ch,32KB=2^0Fh,64KB=2^10h
Note 6:All unused and undefined area data is blank FFh.
P/N: PM1772
40
REV. 2.0, AUG. 02, 2012
MX25L6436E
POWER-ON STATE
The device is at the following states after power-up:
- Standby mode ( please note it is not Deep Power-down mode)
- Write Enable Latch (WEL) bit is reset
The device must not be selected during power-up and power-down stage until the VCC reaches the following levels:
- VCC minimum at power-up stage and then after a delay of tVSL
- GND at power-down
Please note that a pull-up resistor on CS# may ensure a safe and proper power-up/down level.
An internal Power-on Reset (POR) circuit may protect the device from data corruption and inadvertent data change
during power up state.
For further protection on the device, if the VCC does not reach the VCC minimum level, the correct operation is not
guaranteed. The read, write, erase, and program command should be sent after the time delay:
- tVSL after VCC reached VCC minimum level
The device can accept read command after VCC reached VCC minimum and a time delay of tVSL.
Please refer to the figure of "Power-up Timing".
Note:
- To stabilize the VCC level, the VCC rail decoupled by a suitable capacitor close to package pins is recommended.
(generally around 0.1uF)
P/N: PM1772
41
REV. 2.0, AUG. 02, 2012
MX25L6436E
ELECTRICAL SPECIFICATIONS
ABSOLUTE MAXIMUM RATINGS
RATING
VALUE
Ambient Operating Temperature
Industrial grade
-40°C to 85°C
Storage Temperature
-65°C to 150°C
Applied Input Voltage
-0.5V to 4.6V
Applied Output Voltage
-0.5V to 4.6V
VCC to Ground Potential
-0.5V to 4.6V
NOTICE:
1.Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the
device. This is stress rating only and functional operational sections of this specification is not implied. Exposure
to absolute maximum rating conditions for extended period may affect reliability.
2.Specifications contained within the following tables are subject to change.
3.During voltage transitions, all pins may overshoot Vss to -2.0V and Vcc to +2.0V for periods up to 20ns, see Figure 2, 3.
Figure 4. Maximum Positive Overshoot Waveform
Figure 3. Maximum Negative Overshoot Waveform
20ns
20ns
20ns
Vss
Vcc + 2.0V
Vss-2.0V
Vcc
20ns
20ns
20ns
CAPACITANCE TA = 25°C, f = 1.0 MHz
Symbol Parameter
CIN
COUT
P/N: PM1772
Min.
Typ.
Max.
Unit
Input Capacitance
10
pF
VIN = 0V
Output Capacitance
8
pF
VOUT = 0V
42
Conditions
REV. 2.0, AUG. 02, 2012
MX25L6436E
Figure 5. INPUT TEST WAVEFORMS AND MEASUREMENT LEVEL
Input timing reference level
0.8VCC
0.2VCC
0.7VCC
0.3VCC
Output timing reference level
AC
Measurement
Level
0.5VCC
Note: Input pulse rise and fall time are <5ns
Figure 6. OUTPUT LOADING
DEVICE UNDER
TEST
2.7K ohm
CL
6.2K ohm
+3.3V
DIODES=IN3064
OR EQUIVALENT
CL=30/15pF Including jig capacitance
P/N: PM1772
43
REV. 2.0, AUG. 02, 2012
MX25L6436E
Table 10. DC CHARACTERISTICS
Symbol Parameter
Notes
Min.
Max.
Units Test Conditions
ILI
Input Load Current
1
±2
uA
VCC = VCC Max, VIN = VCC or GND
ILO
Output Leakage Current
1
±2
uA
VCC = VCC Max, VOUT=VCC or GND
ISB1
VCC Standby Current
1
50
uA
VIN = VCC or GND, CS# = VCC
ISB2
Deep Power-down
Current
20
uA
VIN = VCC or GND, CS# = VCC
22
mA
fQ=75MHz (4 x I/O read)
SCLK=0.1VCC/0.9VCC, SO=Open
19
mA
f=104MHz
SCLK=0.1VCC/0.9VCC, SO=Open
17
mA
fT=70MHz (2 x I/O read)
SCLK=0.1VCC/0.9VCC, SO=Open
15
mA
f=66MHz
SCLK=0.1VCC/0.9VCC, SO=Open
10
mA
f=33MHz,
SCLK=0.1VCC/0.9VCC, SO=Open
25
mA
Program in Progress, CS# = VCC
20
mA
Program status register in progress,
CS#=VCC
1
25
mA
Erase in Progress, CS#=VCC
1
20
mA
Erase in Progress, CS#=VCC
0.8
V
ICC1
VCC Read
VIL
VCC Program Current
(PP)
VCC Write Status
Register (WRSR) Current
VCC Sector Erase
Current (SE)
VCC Chip Erase Current
(CE)
Input Low Voltage
VIH
Input High Voltage
VOL
Output Low Voltage
VOH
Output High Voltage
ICC2
ICC3
ICC4
ICC5
1
1
-0.5
0.7VCC VCC+0.4
0.4
VCC-0.2
V
V
IOL = 1.6mA
V
IOH = -100uA
Notes :
1. Typical values at VCC = 3.3V, T = 25°C. These currents are valid for all product versions (package and speeds).
2.Typical value is calculated by simulation.
P/N: PM1772
44
REV. 2.0, AUG. 02, 2012
MX25L6436E
Table 11. AC CHARACTERISTICS
Symbol
Alt. Parameter
Clock Frequency for the following instructions:
fSCLK
fC FAST_READ, RDSFDP, PP, SE, BE, CE, DP, RES, RDP,
WREN, WRDI, RDID, RDSR, WRSR
fRSCLK
fR Clock Frequency for READ instructions
fT Clock Frequency for DREAD instructions
fTSCLK
VCC=2.7V-3.6V
fQ Clock Frequency for QREAD instructions
VCC=3.0V-3.6V
f4PP
Clock Frequency for 4PP (Quad page program)
Fast_Read
tCH(1)
tCLH Clock High Time
Read
Fast_Read
tCL(1)
tCLL Clock Low Time
Read
tCLCH(2)
Clock Rise Time (3) (peak to peak)
tCHCL(2)
Clock Fall Time (3) (peak to peak)
tSLCH tCSS CS# Active Setup Time (relative to SCLK)
tCHSL
CS# Not Active Hold Time (relative to SCLK)
tDVCH tDSU Data In Setup Time
tCHDX
tDH Data In Hold Time
tCHSH
CS# Active Hold Time (relative to SCLK)
tSHCH
CS# Not Active Setup Time (relative to SCLK)
Read
tSHSL(3) tCSH CS# Deselect Time
Write/Erase/
Program
VCC=2.7V-3.6V
(2)
tSHQZ
tDIS Output Disable Time
VCC=3.0V-3.6V
1 I/O
Clock Low to Output Valid Loading: 15pF
tCLQV
tV
2 I/O & 4 I/O
VCC=2.7V~3.6V
Loading: 30pF 2 I/O & 4 I/O
tCLQX
tHO Output Hold Time
tWHSL
Write Protect Setup Time
tSHWL
Write Protect Hold Time
(2)
tDP
CS# High to Deep Power-down Mode
CS# High to Standby Mode without Electronic Signature
tRES1(2)
Read
(2)
tRES2
CS# High to Standby Mode with Electronic Signature Read
tW
Write Status Register Cycle Time
tBP
Byte-Program
tPP
Page Program Cycle Time
tSE
Sector Erase Cycle Time (4KB)
tBE
Block Erase Cycle Time (32KB)
tBE
Block Erase Cycle Time (64KB)
P/N: PM1772
45
Min.
Typ.
Max.
Unit
104
MHz
50
70
75
85
20
4.5
9
4.5
9
0.1
0.1
5
5
2
5
5
5
15
MHz
MHz
MHz
MHz
MHz
ns
ns
ns
ns
V/ns
V/ns
ns
ns
ns
ns
ns
ns
ns
50
ns
D.C.
10
8
9
9.5
12
10
ns
ns
ns
ns
ns
ns
ns
ns
us
100
us
100
100
300
5
300
2
2
us
ms
us
ms
ms
s
s
1
20
100
40
9
1.4
60
0.5
0.7
REV. 2.0, AUG. 02, 2012
MX25L6436E
Symbol
tCE
tWPS
tWSR
Alt. Parameter
Chip Erase Cycle Time
Write Protection Selection Time
Write Security Register Time
Min.
Typ.
50
Max.
80
1
1
Unit
s
ms
ms
Notes:
1. tCH + tCL must be greater than or equal to 1/ fC.
2. Value guaranteed by characterization, not 100% tested in production.
3. Only applicable as a constraint for a WRSR instruction when SRWD is set at 1.
P/N: PM1772
46
REV. 2.0, AUG. 02, 2012
MX25L6436E
Timing Analysis
Figure 7. Serial Input Timing
tSHSL
CS#
tCHSL
tSLCH
tCHSH
tSHCH
SCLK
tDVCH
tCHCL
tCHDX
tCLCH
LSB
MSB
SI
High-Z
SO
Figure 8. Output Timing
CS#
tCH
SCLK
tCLQV
tCLQX
tCL
tCLQV
tCLQX
LSB
SO
SI
P/N: PM1772
tSHQZ
ADDR.LSB IN
47
REV. 2.0, AUG. 02, 2012
MX25L6436E
Figure 9. WP# Setup Timing and Hold Timing during WRSR when SRWD=1
WP#
tSHWL
tWHSL
CS#
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
SCLK
01
SI
SO
High-Z
Figure 10. Write Enable (WREN) Sequence (Command 06)
CS#
0
1
2
3
4
5
6
6
7
7
SCLK
Command
SI
06
High-Z
SO
Figure 11. Write Disable (WRDI) Sequence (Command 04)
CS#
0
1
2
3
4
5
SCLK
Command
SI
SO
P/N: PM1772
04
High-Z
48
REV. 2.0, AUG. 02, 2012
MX25L6436E
Figure 12. Read Identification (RDID) Sequence (Command 9F)
CS#
0
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18
28 29 30 31
SCLK
Command
SI
9F
Manufacturer Identification
High-Z
SO
Device Identification
D7 D6 D5 D4 D3 D2 D1 D0 D15 D14 D13
MSB
D3 D2 D1 D0
MSB
Figure 13. Read Status Register (RDSR) Sequence (Command 05)
CS#
0
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15
SCLK
command
05
SI
SO
Status Register Out
High-Z
D7 D6 D5 D4 D3 D2 D1 D0
MSB
Figure 14. Write Status Register (WRSR) Sequence (Command 01)
CS#
0
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15
SCLK
SI
SO
P/N: PM1772
command
Status
Register In
01
D7 D6 D5 D4 D3 D2 D1 D0
MSB
High-Z
49
REV. 2.0, AUG. 02, 2012
MX25L6436E
Figure 15. Read Data Bytes (READ) Sequence (Command 03)
CS#
0
1
2
3
4
5
6
7
8
9 10
28 29 30 31 32 33 34 35 36 37 38 39
SCLK
Command
24 ADD Cycles
03
SI
A23 A22 A21
A3 A2 A1 A0
MSB
SO
Data Out 2
Data Out 1
High-Z
D7 D6 D5 D4 D3 D2 D1 D0 D7
MSB
MSB
Figure 16. Read at Higher Speed (FAST_READ) Sequence (Command 0B)
CS#
0
1
2
3
4
5
6
7
8
28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47
9 10
SCLK
Command
SI
8 Dummy Cycles
24 ADD Cycles
0B
A23 A22 A21
A3 A2 A1 A0
Data Out 1
High-Z
SO
Data Out 2
D7 D6 D5 D4 D3 D2 D1 D0 D7
MSB
Figure 17. Dual Read Mode Sequence (Command 3B)
CS#
0
1
2
3
4
5
6
7
8
…
Command
SI/SIO0
SO/SIO1
P/N: PM1772
30 31 32
9
SCLK
3B
…
24 ADD Cycle
A23 A22
…
High Impedance
39 40 41 42 43 44 45
A2 A0
8 dummy
cycle
Data Out
1
Data Out
2
D6 D4 D2 D0 D6 D4
D7 D5 D3 D1 D7 D5
50
REV. 2.0, AUG. 02, 2012
MX25L6436E
Figure 18. Quad Read Mode Sequence (Command 6B)
CS#
0
1
2
3
4
5
6
7
8
SCLK
…
Command
SI/SO0
SO/SO1
WP#/SO2
NC/SO3
P/N: PM1772
29 30 31 32 33
9
6B
…
24 ADD Cycles
A23 A22
…
38 39 40 41 42
A2 A1 A0
High Impedance
8 dummy cycles
Data Data
Out 1 Out 2
Data
Out 3
D4 D0 D4 D0 D4
D5 D1 D5 D1 D5
High Impedance
D6 D2 D6 D2 D6
High Impedance
D7 D3 D7 D3 D7
51
REV. 2.0, AUG. 02, 2012
MX25L6436E
Figure 19. Sector Erase (SE) Sequence (Command 20)
CS#
0
1
2
3
4
5
6
7
8
9
29 30 31
SCLK
…
24 ADD Cycles
Command
SI
…
A23 A22
20
A2 A1 A0
MSB
Figure 20. Block Erase (BE/BE32K) Sequence (Command D8/52)
CS#
0
1
2
3
4
5
6
7
8
9
29 30 31
SCLK
24 ADD Cycles
Command
SI
D8/52
A23 A22
A2 A1 A0
MSB
Figure 21. Chip Erase (CE) Sequence (Command 60 or C7)
CS#
0
1
2
3
4
5
6
7
SCLK
Command
SI
P/N: PM1772
60 or C7
52
REV. 2.0, AUG. 02, 2012
MX25L6436E
Figure 22. Page Program (PP) Sequence (Command 02)
2079
2078
2077
2076
2075
2074
28 29 30 31 32 33 34 35 36 37 38 39
2073
0 1 2 3 4 5 6 7 8 9 10
2072
CS#
SCLK
Command
24 ADD Cycles
A23 A22 A21
02
SI
A3 A2 A1 A0
Data Byte 1
Data Byte 256
D7 D6 D5 D4 D3 D2 D1 D0
D7 D6 D5 D4 D3 D2 D1 D0
MSB
MSB
Figure 23. 4 x I/O Page Program (4PP) Sequence (Command 38)
CS#
0
1
2
3
4
5
6
7
8
SCLK
…
Command
6 ADD cycles
Data
Byte 256
Data Data
Byte 1 Byte 2
A20 A16 A12 A8 A4 A0 D4 D0 D4 D0
…
D4 D0
SO/SIO1
A21 A17 A13 A9 A5 A1 D5 D1 D5 D1
…
D5 D1
WP#/SIO2
A22 A18 A14 A10 A6 A2 D6 D2 D6 D2
…
D6 D2
NC/SIO3
A23 A19 A15 A11 A7 A3 D7 D3 D7 D3
…
D7 D3
SI/SIO0
P/N: PM1772
524 525
9 10 11 12 13 14 15 16 17
38
53
REV. 2.0, AUG. 02, 2012
MX25L6436E
Figure 24. Continously Program (CP) Mode Sequence with Hardware Detection (Command AD)
CS#
0 1
30 31 31 32
6 7 8 9
47 48
0 1
6 7 8
20 21 22 23 24
0
7
7 8
0
SCLK
Command
SI
AD (hex)
Valid
Command (1)
data in
Byte 0, Byte1
24-bit address
high impedance
S0
data in
Byte n-1, Byte n
04 (hex)
05 (hex)
status (2)
Notes: (1) During CP mode, the valid commands are CP command (AD hex), WRDI command (04 hex), RDSR command
(05 hex), and RDSCUR command (2B hex).
(2) Once an internal programming operation begins, CS# goes low will drive the status on the SO pin and CS#
goes high will return the SO pin to tri-state.
(3) To end the CP mode, either reaching the highest unprotected address or sending Write Disable (WRDI) command (04 hex) may achieve it and then it is recommended to send RDSR command (05 hex) to verify if CP
mode is ended.
Figure 25. Deep Power-down (DP) Sequence (Command B9)
CS#
0
1
2
3
4
5
6
tDP
7
SCLK
Command
SI
B9
Stand-by Mode
P/N: PM1772
54
Deep Power-down Mode
REV. 2.0, AUG. 02, 2012
MX25L6436E
Figure 26. Read Electronic Signature (RES) Sequence (Command AB)
CS#
0
1
2
3
4
5
6
7
8
9 10
28 29 30 31 32 33 34 35 36 37 38 39
SCLK
Command
SI
tRES2
24 ADD Cycles
AB
A23 A22 A21
… A3
A2 A1 A0
MSB
Electronic Signature Out
High-Z
SO
D7 D6 D5 D4 D3 D2 D1 D0
MSB
Deep Power-down Mode
Stand-by Mode
Figure 27. Release from Deep Power-down (RDP) Sequence (Command AB)
CS#
0
1
2
3
4
5
6
tRES1
7
SCLK
Command
SI
SO
AB
High-Z
Deep Power-down Mode
P/N: PM1772
55
Stand-by Mode
REV. 2.0, AUG. 02, 2012
MX25L6436E
Figure 28. Read Electronic Manufacturer & Device ID (REMS) Sequence (Command 90 or EF or DF)
CS#
0 1 2 3 4 5 6 7 8 9 10
28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47
SCLK
Command
SI
SO
90
24 ADD Cycles
A3 A2 A1 A0
A23 A22 A21
Manufacturer ID
High-Z
Device ID
D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0
MSB
MSB
MSB
Notes:
1. A0=0 will output the Manufacturer ID first and A0=1 will output Device ID first. A1~A23 is don't care.
2. Instruction is either 90(hex) or EF(hex) or DF(hex).
Figure 29. Write Protection Selection (WPSEL) Sequence (Command 68)
CS#
0
1
2
3
4
5
6
7
SCLK
Command
SI
P/N: PM1772
68
56
REV. 2.0, AUG. 02, 2012
MX25L6436E
Figure 30. Single Block Lock/Unlock Protection (SBLK/SBULK) Sequence (Command 36/39)
CS#
0
1
2
3
4
5
6
7
8
9
29 30 31
SCLK
24 Bit Address
Cycles
Command
SI
36/39
A23 A22
A2 A1 A0
MSB
Figure 31. Read Block Protection Lock Status (RDBLOCK) Sequence (Command 3C)
CS#
0
1
2
3
4
5
6
7
8
28 29 30 31 32 33 34 35 36 37 38 39
9 10
SCLK
Command
SI
3C
24 ADD Cycles
A23 A22 A21
A3 A2 A1 A0
MSB
SO
Block Protection Lock status out
High-Z
D7 D6 D5 D4 D3 D2 D1 D0
MSB
Figure 32. Gang Block Lock/Unlock (GBLK/GBULK) Sequence (Command 7E/98)
CS#
0
1
2
3
4
5
6
7
SCLK
Command
SI
P/N: PM1772
7E/98
57
REV. 2.0, AUG. 02, 2012
MX25L6436E
Figure 33. Power-up Timing
VCC
VCC(max)
Chip Selection is Not Allowed
VCC(min)
tVSL
Device is fully accessible
time
Note: VCC (max.) is 3.6V and VCC (min.) is 2.7V.
Table 12. Power-Up Timing
Symbol
tVSL(1)
Parameter
VCC(min) to CS# low
Min.
300
Max.
Unit
us
Note: The parameter is characterized only.
INITIAL DELIVERY STATE
The device is delivered with the memory array erased: all bits are set to 1 (each byte contains FFh). The Status
Register contains 00h (all Status Register bits are 0).
P/N: PM1772
58
REV. 2.0, AUG. 02, 2012
MX25L6436E
OPERATING CONDITIONS
At Device Power-Up and Power-Down
AC timing illustrated in Figure 34 and Figure 35 are for the supply voltages and the control signals at device powerup and power-down. If the timing in the figures is ignored, the device will not operate correctly.
During power-up and power-down, CS# needs to follow the voltage applied on VCC to keep the device not to be
selected. The CS# can be driven low when VCC reach Vcc(min.) and wait a period of tVSL.
Figure 34. AC Timing at Device Power-Up
VCC
VCC(min)
GND
tVR
tSHSL
CS#
tSLCH
tCHSL
tSHCH
tCHSH
SCLK
tDVCH
tCHCL
tCHDX
LSB IN
MSB IN
SI
High Impedance
SO
Symbol
tVR
tCLCH
Parameter
VCC Rise Time
Notes
1
Min.
20
Max.
500000
Unit
us/V
Notes :
1.Sampled, not 100% tested.
2.For AC spec tCHSL, tSLCH, tDVCH, tCHDX, tSHSL, tCHSH, tSHCH, tCHCL, tCLCH in the figure, please refer to
"Table 11. AC CHARACTERISTICS".
P/N: PM1772
59
REV. 2.0, AUG. 02, 2012
MX25L6436E
Figure 35. Power-Down Sequence
During power-down, CS# needs to follow the voltage drop on VCC to avoid mis-operation.
VCC
CS#
SCLK
P/N: PM1772
60
REV. 2.0, AUG. 02, 2012
MX25L6436E
ERASE AND PROGRAMMING PERFORMANCE
Parameter
Write Status Register Cycle Time
Sector Erase Time (4KB)
Block Erase Time (64KB)
Block Erase Time (32KB)
Chip Erase Time
Byte Program Time (via page program command)
Page Program Time
Erase/Program Cycle
Typ. (1)
40
60
0.7
0.5
50
9
1.4
100,000
Max. (2)
100
300
2
2
80
300
5
Unit
ms
ms
s
s
s
us
ms
cycles
Notes:
1. Typical program and erase time assumes the following conditions: 25°C, 3.3V, and checker board pattern.
2. Under worst conditions of 85°C and 2.7V.
3. System-level overhead is the time required to execute the first-bus-cycle sequence for the programming command.
DATA RETENTION
Parameter
Condition
Min.
Data retention
55˚C
20
Max.
Unit
years
LATCH-UP CHARACTERISTICS
Input Voltage with respect to GND on all power pins, SI, CS#
Input Voltage with respect to GND on SO
Current
Includes all pins except VCC. Test conditions: VCC = 3.0V, one pin at a time.
P/N: PM1772
61
Min.
-1.0V
-1.0V
-100mA
Max.
2 VCCmax
VCC + 1.0V
+100mA
REV. 2.0, AUG. 02, 2012
MX25L6436E
ORDERING INFORMATION
PART NO.
CLOCK (MHz)
TEMPERATURE
MX25L6436EMI-10G*
104
-40°C~85°C
MX25L6436EM2I-10G
104
-40°C~85°C
MX25L6436EZNI-10G*
104
-40°C~85°C
PACKAGE
Remark
16-SOP
(300mil)
8-SOP
(200mil)
8-WSON
(8x6mm)
RoHS
Compliant
RoHS
Compliant
RoHS
Compliant
* Advanced Information
P/N: PM1772
62
REV. 2.0, AUG. 02, 2012
MX25L6436E
PART NAME DESCRIPTION
MX 25
L 6436E
M
I
10 G
OPTION:
G: RoHS Compliant
SPEED:
10: 104MHz
TEMPERATURE RANGE:
I: Industrial (-40° C to 85° C)
PACKAGE:
M: 300mil 16-SOP
M2: 200mil 8-SOP
ZN: 8x6mm 8-WSON
DENSITY & MODE:
6436E: 64Mb standard type
TYPE:
L: 3V
DEVICE:
25: Serial Flash
P/N: PM1772
63
REV. 2.0, AUG. 02, 2012
MX25L6436E
PACKAGE INFORMATION
P/N: PM1772
64
REV. 2.0, AUG. 02, 2012
MX25L6436E
P/N: PM1772
65
REV. 2.0, AUG. 02, 2012
MX25L6436E
P/N: PM1772
66
REV. 2.0, AUG. 02, 2012
MX25L6436E
REVISION HISTORY
Revision No. Description
1.1
1. Added 64Mb general feature description.
2. Aligned pin name.
3. Update dummy cycle at 2 x I/O, 4 x I/O read mode.
4. Rename CFI to DMC.
5. Added DMC contents.
6. Revised Address 19 Data.
7. Revised Address 09 Data.
Page
P5
P7,10,18,19,
P23,48,50
P5
P6,14,16,36
P36~38
P37
P38
Date
NOV/18/2009
1.2
1. Added 8-WSON package information
P6,8,63,64,67 APR/15/2010
2. Separated power consumption by I/O number
P5,42,43
3. Modified tSLCH & tSHCH from 8ns to 5ns
P44,45
4. Modified Figure 6. Output TimingP47
5. Modified Discoverable Memory Capabilities (DMC) table & noteP36,38
6. Modified Figure 33P61
7. Added Figure 34P62
8. Modified Ordering InformationP64
1.3
1. Removed DMC descriptions P6,14,16,
P36-38
1.4
1. Removed Advanced Information from MX25L12836EZNI-10G P61
1.5
1. Modified Parameters for tCHDX in Table 8-1
P41
2. Modified Serial Parameters for tCHDX in Table 8-2 P42
1.6
1. Removed MX25L12836E information from the previous All combined version of MX25L6436E/MX25L12836E
2. Modified Input CapacitanceP36
3. Modified tCLQXP39
1.7
1. Corrected the REMS descriptions P26,27,50
1.8
1. Modified Figure 35. Power-Down SequenceP60
2. Added Read SFDP (RDSFDP) Mode
P6,13,14,
P35~40
3. Changed ordering information format
P62
1.9
1. Modified QREAD Frequency from 70MHz to 75MHz
P5,7,44,45
2. Modified SFDP wording
P35~40
2.0
1. Revised SFDP table.
P37
P/N: PM1772
67
JUL/06/2010
NOV/18/2010
JAN/27/2011
OCT/20/2011
NOV/23/2011
DEC/26/2011
APR/30/2012
AUG/02/2012
REV. 2.0, AUG. 02, 2012
MX25L6436E
Except for customized products which has been expressly identified in the applicable agreement, Macronix's
products are designed, developed, and/or manufactured for ordinary business, industrial, personal, and/or
household applications only, and not for use in any applications which may, directly or indirectly, cause death,
personal injury, or severe property damages. In the event Macronix products are used in contradicted to their
target usage above, the buyer shall take any and all actions to ensure said Macronix's product qualified for its
actual use in accordance with the applicable laws and regulations; and Macronix as well as it’s suppliers and/or
distributors shall be released from any and all liability arisen therefrom.
Copyright© Macronix International Co., Ltd. 2009~2012. All rights reserved, including the trademarks and
tradename thereof, such as Macronix, MXIC, MXIC Logo, MX Logo, Integrated Solutions Provider, NBit, Nbit,
NBiit, Macronix NBit, eLiteFlash, HybridNVM, HybridFlash, XtraROM, Phines, KH Logo, BE-SONOS, KSMC,
Kingtech, MXSMIO, Macronix vEE, Macronix MAP, Rich Audio, Rich Book, Rich TV, and FitCAM. The names
and brands of third party referred thereto (if any) are for identification purposes only.
For the contact and order information, please visit Macronix’s Web site at: http://www.macronix.com
MACRONIX INTERNATIONAL CO., LTD. reserves the right to change product and specifications without notice.
68