HA17358B Series Dual Operational Amplifier REA03D0001-0100 Rev.1.00 Dec 25, 2006 Description HA17358B is dual operational amplifiers that provide high gain and internal phase compensation, with single power supply. Operation from split power supply is also possible and the low power supply current drain is independent of the magnitude of the power supply voltages. They can be widely applied to control equipment and to general use. Features • Wide range of supply voltage Single supply: 3 V to 36 V, Dual supplies: ±1.5 V to ±18 V • Wide range of common mode voltage, and possible to operate with an input about 0 V, and output around 0 V is available. • Internally frequency compensated for unity gain. • Common mode input voltage range includes ground. • Package outline available in Pb free lead frame: DP-8 SOP-8 (JEITA) SOP-8 (JEDEC) Applications • Battery charger • Cordless telephone • Switching power supply Ordering Information Type No. HA17358B HA17358BF Application Commercial use HA17358BRP Note: This product is designed for consumer use and not for automotive. Rev.1.00 Dec 25, 2006 page 1 of 8 Package Code (Package Name) PRDP0008AF-B (DP-8FV) PRSP0008DE-B (FP-8DGV) PRSP0008DD-C (FP-8DCV) HA17358B Series Pin Arrangement Vout1 1 Vin(–)1 2 Vin(+)1 3 GND 4 1 – + 2 + – 8 VCC 7 Vout2 6 Vin(–)2 5 Vin(+)2 (Top view) Circuit Schematic (1/2) VCC 6 µA 4 µA 100 µA Q5 Q6 Q2 Q3 – Input CC Q7 Q4 Q1 RSC Output Q11 + Input Q10 Q8 Rev.1.00 Dec 25, 2006 page 2 of 8 Q9 Q13 Q12 50 µA HA17358B Series Absolute Maximum Ratings (Ta = 25°C) Item Symbol HA17358B Ratings HA17358BF HA17358BRP Unit 36 VCC 36 VCC 36 VCC V V Supply Voltage Differential input voltage VCC VIN (diff) Common mode input voltage Power dissipation VCM PT –0.3 to VCC 1 570 * –0.3 to VCC 2 385 * –0.3 to VCC 2 385 * V mW Operating temperature Storage temperature Topr Tstg –40 to +85 –55 to +125 –40 to +85 –55 to +125 –40 to +85 –55 to +125 °C °C Notes: 1. This is the allowable value up to Ta = 55°C. Derate by 8.3 mW/°C above that temperature. 2. These are the allowable values up to Ta = 25°C mounting in air. When it is mounted on glass epoxy board of 40 mm × 40 mm × 1.5 mm (t) with 30% wiring density, the allowable value is 570 mW up to Ta = 45°C. If Ta > 45°C, derate by 7.14 mW/°C. Electrical Characteristics (Ta = 25°C, VCC = +5 V, unless otherwise specified) Item Symbol Min Typ Max Unit 2 5 mV Test Conditions Input offset voltage VIO — Input offset current IIO — 5 30 nA VO = 1.4 V, RS = 0 Ω VCC = 5 V to 30 V VCM = 0 V, IIO = | IIN(+) – IIN(–) | Input bias current Power supply rejection ratio IIB PSRR — — 20 100 200 — nA dB VCM = 0 V, IIN(+) or IIN(–) VCC = 5 V to 30 V Voltage gain AV 85 100 — dB Common mode rejection Ratio CMR 60 70 — dB VCC = 15 V, RL ≥ 2 kΩ, VO = 1 V to 11 V DC, VCM = 0 V to (VCC – 1.5) V Common mode input voltage range Output swing voltage VIR VOH 0 26 — — VCC–1.5 — V V VCC = 30 V VCC = 30 V, RL = 2 kΩ VOL 27 — 28 5 — 20 V mV VCC = 30 V, RL = 10 kΩ VCC = 5 V, RL = 10 kΩ Output source current IOSOURCE 20 40 — mA Output sink current IOSINK 10 15 — mA VIN(+) = 1 V, VIN(–) = 0 V, VO = 2 V, VCC = 15 V VIN(–) = 1 V, VIN(+) = 0 V, VO = 2 V, VCC = 15 V 12 50 — µA ICC — 0.5 1.2 mA VIN(–) = 1 V, VIN(+) = 0 V, VO = 0.2 V, VCC = 15 V RL = ∞, VCC = 5 V CS — — 0.7 –120 2 — mA dB RL = ∞, VCC = 30 V f = 1 kHz to 20 kHz Supply current Channel separation Rev.1.00 Dec 25, 2006 page 3 of 8 HA17358B Series Table of Graphs Electrical Characteristics Figure Input voltage Input bias current vs. Supply voltage ±VCC vs. Temperature Ta 1 2 Supply current Voltage gain vs. Supply voltage ±VCC vs. Supply voltage VCC 3 4 Voltage gain Output swing voltage vs. Frequency f vs. Frequency f 5 6 Output source current Output sink current vs. Output voltage VO vs. Output voltage VO 7 8 Rev.1.00 Dec 25, 2006 page 4 of 8 HA17358B Series Typical Characteristics Curves Figure 1. Input Voltage vs. Supply Voltage Figure 2. Input Bias Current vs. Temperature 50 VCC = 5 V 15 Input bias current (nA) Input voltage (V) Ta = 25°C 10 Nagative Positive 5 0 0 5 10 Supply voltage ±VCC (V) 0.4 0.3 10 –20 0 20 40 60 Temperature Ta (°C) 80 Figure 4. Voltage Gain vs. Supply Voltage Ta = 25°C 0.8 0.5 20 140 Voltage gain (dB) Supply current (mA) Figure 3. Supply Current vs. Supply Voltage 1 0.9 Ta = 25°C 0.6 30 0 –40 15 0.7 40 0.2 120 RL = 20 kΩ 100 RL = 2 kΩ 80 0.1 0 0 4 8 12 16 Supply voltage ±VCC (V) 60 20 VCC = 15 V Ta = 25°C 1 10 100 1k 10 k 100 k Frequency f (Hz) Rev.1.00 Dec 25, 2006 page 5 of 8 1M Output swing voltage (V) Voltage gain (dB) Figure 5. Voltage Gain vs. Frequency 120 110 100 90 80 70 60 50 40 30 20 10 0 0 5 10 15 20 25 30 35 Supply voltage VCC (V) 40 Figure 6 Output Swing Voltage vs. Frequency 20 VCC = 15 V Ta = 25°C 15 10 5 0 100 1k 10 k 100 k Frequency f (Hz) 1M HA17358B Series Figure 7. Output Source Current vs. Output Voltage 60 VCC = 15 V 50 Ta = 25°C 40 30 20 10 0 7.5 8.5 9.5 10.5 11.5 12.5 13.5 14.5 Output voltage VO (V) Rev.1.00 Dec 25, 2006 page 6 of 8 Output sink current (mA) Output source current (mA) Typical Characteristics Curves (cont.) Figure 8. Output Sink Current vs. Output Voltage 30 VCC = 15 V 25 Ta = 25°C 20 15 10 5 0 0 1 2 3 4 5 6 Output voltage VO (V) 7 HA17358B Series Package Dimensions JEITA Package Code P-DIP8-6.3x9.6-2.54 RENESAS Code PRDP0008AF-B Previous Code DP-8FV MASS[Typ.] 0.54g D 5 E 8 1 4 b3 0.89 A1 A Z Reference Symbol L e1 D E A A1 bp b3 c θ e Z L θ bp e c e1 ( Ni/Pd/Au plating ) JEITA Package Code P-SOP8-4.4x4.85-1.27 RENESAS Code PRSP0008DE-B *1 Previous Code FP-8DGV Min Nom Max 7.62 9.60 10.6 6.30 7.4 5.06 0.5 0.40 0.48 0.56 1.30 0.19 0.25 0.31 15° 0° 2.29 2.54 2.79 1.27 2.54 MASS[Typ.] 0.1g F D 8 Dimension in Millimeters NOTE) 1. DIMENSIONS"*1 (Nom)"AND"*2" DO NOT INCLUDE MOLD FLASH. 2. DIMENSION"*3"DOES NOT INCLUDE TRIM OFFSET. 5 c *2 E HE bp Index mark Terminal cross section ( Ni/Pd/Au plating ) 1 Z Reference Symbol 4 e *3 bp x M A L1 A1 θ L y Detail F Rev.1.00 Dec 25, 2006 page 7 of 8 D E A2 A1 A bp b1 c c1 θ HE e x y Z L L1 Dimension in Millimeters Min Nom Max 4.85 5.25 4.4 0.00 0.1 0.35 0.4 0.20 2.03 0.45 0.15 0.20 0.25 0° 6.35 8° 6.5 6.75 1.27 0.12 0.15 0.75 0.42 0.60 0.85 1.05 HA17358B Series JEITA Package Code P-SOP8-3.95x4.9-1.27 RENESAS Code PRSP0008DD-C *1 Previous Code FP-8DCV MASS[Typ.] 0.085g F D 8 NOTE) 1. DIMENSIONS"*1 (Nom)"AND"*2" DO NOT INCLUDE MOLD FLASH. 2. DIMENSION"*3"DOES NOT INCLUDE TRIM OFFSET. 5 c *2 E HE bp Index mark Terminal cross section ( Ni/Pd/Au plating ) 1 Z Reference Symbol 4 e *3 bp x M A L1 A1 θ L y Detail F Rev.1.00 Dec 25, 2006 page 8 of 8 D E A2 A1 A bp b1 c c1 θ HE e x y Z L L1 Dimension in Millimeters Min Nom Max 4.90 5.30 3.95 0.10 0.14 0.25 1.75 0.34 0.40 0.46 0.15 0.20 0.25 0° 8° 5.80 6.10 6.20 1.27 0.25 0.10 0.75 0.40 0.60 1.27 1.08 Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan Notes: 1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use. Renesas neither makes warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property rights or any other rights of Renesas or any third party with respect to the information in this document. 2. Renesas shall have no liability for damages or infringement of any intellectual property or other rights arising out of the use of any information in this document, including, but not limited to, product data, diagrams, charts, programs, algorithms, and application circuit examples. 3. You should not use the products or the technology described in this document for the purpose of military applications such as the development of weapons of mass destruction or for the purpose of any other military use. When exporting the products or technology described herein, you should follow the applicable export control laws and regulations, and procedures required by such laws and regulations. 4. All information included in this document such as product data, diagrams, charts, programs, algorithms, and application circuit examples, is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas products listed in this document, please confirm the latest product information with a Renesas sales office. Also, please pay regular and careful attention to additional and different information to be disclosed by Renesas such as that disclosed through our website. (http://www.renesas.com ) 5. Renesas has used reasonable care in compiling the information included in this document, but Renesas assumes no liability whatsoever for any damages incurred as a result of errors or omissions in the information included in this document. 6. When using or otherwise relying on the information in this document, you should evaluate the information in light of the total system before deciding about the applicability of such information to the intended application. Renesas makes no representations, warranties or guaranties regarding the suitability of its products for any particular application and specifically disclaims any liability arising out of the application and use of the information in this document or Renesas products. 7. With the exception of products specified by Renesas as suitable for automobile applications, Renesas products are not designed, manufactured or tested for applications or otherwise in systems the failure or malfunction of which may cause a direct threat to human life or create a risk of human injury or which require especially high quality and reliability such as safety systems, or equipment or systems for transportation and traffic, healthcare, combustion control, aerospace and aeronautics, nuclear power, or undersea communication transmission. If you are considering the use of our products for such purposes, please contact a Renesas sales office beforehand. Renesas shall have no liability for damages arising out of the uses set forth above. 8. Notwithstanding the preceding paragraph, you should not use Renesas products for the purposes listed below: (1) artificial life support devices or systems (2) surgical implantations (3) healthcare intervention (e.g., excision, administration of medication, etc.) (4) any other purposes that pose a direct threat to human life Renesas shall have no liability for damages arising out of the uses set forth in the above and purchasers who elect to use Renesas products in any of the foregoing applications shall indemnify and hold harmless Renesas Technology Corp., its affiliated companies and their officers, directors, and employees against any and all damages arising out of such applications. 9. You should use the products described herein within the range specified by Renesas, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas shall have no liability for malfunctions or damages arising out of the use of Renesas products beyond such specified ranges. 10. Although Renesas endeavors to improve the quality and reliability of its products, IC products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Please be sure to implement safety measures to guard against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other applicable measures. Among others, since the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. 11. In case Renesas products listed in this document are detached from the products to which the Renesas products are attached or affixed, the risk of accident such as swallowing by infants and small children is very high. You should implement safety measures so that Renesas products may not be easily detached from your products. Renesas shall have no liability for damages arising out of such detachment. 12. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written approval from Renesas. 13. Please contact a Renesas sales office if you have any questions regarding the information contained in this document, Renesas semiconductor products, or if you have any other inquiries. http://www.renesas.com RENESAS SALES OFFICES Refer to "http://www.renesas.com/en/network" for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501 Renesas Technology Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K. Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900 Renesas Technology (Shanghai) Co., Ltd. Unit 204, 205, AZIACenter, No.1233 Lujiazui Ring Rd, Pudong District, Shanghai, China 200120 Tel: <86> (21) 5877-1818, Fax: <86> (21) 6887-7898 Renesas Technology Hong Kong Ltd. 7th Floor, North Tower, World Finance Centre, Harbour City, 1 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: <852> 2265-6688, Fax: <852> 2730-6071 Renesas Technology Taiwan Co., Ltd. 10th Floor, No.99, Fushing North Road, Taipei, Taiwan Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999 Renesas Technology Singapore Pte. Ltd. 1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632 Tel: <65> 6213-0200, Fax: <65> 6278-8001 Renesas Technology Korea Co., Ltd. Kukje Center Bldg. 18th Fl., 191, 2-ka, Hangang-ro, Yongsan-ku, Seoul 140-702, Korea Tel: <82> (2) 796-3115, Fax: <82> (2) 796-2145 Renesas Technology Malaysia Sdn. Bhd Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No.18, Jalan Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia Tel: <603> 7955-9390, Fax: <603> 7955-9510 © 2006. Renesas Technology Corp., All rights reserved. Printed in Japan. Colophon .7.0