51992 CURRENT DRIVER DSCC DWG #5962-87617 (Replacement for DH0006) Features: Applications: • • • • • • • • • • Operation from a Single +10V to +45V Power Supply Low Standby Power Dissipation of only 35mW for 28V Power Supply 1.5A, 50ms on, 1 sec off, Pulse Capability Meets MIL-PRF-38534 Class H Requirements Environmentally Screened per MIL-STD-883 Mii MICROPAC MICROCIRCUITS PRODUCTS DIVISION Military / High Reliability Systems Aircraft Engine Environment Controls – High Current Pulse Applications Lamp Driver DESCRIPTION The 51992 is a high voltage current driver with DTL compatible TTL logic levels and drive a load up to 400 mA at 28V. Should additional gating be required, AND inputs are provided along with an Expander connection. The addition of an external capacitor provides control of the rise and fall times of the output in order to decrease cold lamp surges or to minimize electromagnetic interference if long lines are driven. Device can be gated On and Off at normal inputs or at pin 8. Since one side of the load is normally grounded there is less likelihood of false turn-on due to an inadvertent short in the drive line. Meets the requirements of SMD 5962-87617. ABSOLUTE MAXIMUM RATINGS Peak Power Supply Voltage (for less than 0.1s) ................................................................................................................... 60V Continuous Supply Voltage .................................................................................................................................................... 45V Input Voltage …………..……………………………………………………………………………………………………………5.5V Input Expander Current ......................................................................................................................................................5.0mA Peak Output Current (50ms On 1 sec. Off) .......................................................................................................................... 1.5A Continuous Output Current ................................................................................................................................................... 0.4A Operating Temperature ......................................................................................................................................-55ºC to +125ºC Storage Temperature .........................................................................................................................................-65ºC to +150ºC Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCIRCUITS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 www.micropac.com E-MAIL: [email protected] 5/22/02 Pg. 1 of 3 51992 CURRENT DRIVER ELECTRICAL CHARACTERISTICS (-55ºC ≤ Ta ≤ +125ºC) PARAMETER CONDITIONS MIN Logical “1” Input Voltage 10V ≤ Vcc ≤ 45V 2.0 Logical “0” Input Voltage 10V ≤ Vcc ≤ 45V MAX UNITS V 0.8 V Logical “1” Output Voltage Vcc = 10V, Vin = 2V, Iout = 150mA Vcc = 28V, Vin = 2V, RL = 82Ω Logical “0” Output Voltage Vcc = 45V, Vin = 0.8, RL = 1KΩ 10 mV Logical “1” Input Current Vcc = 45V, Vin = 2.4V Vcc = 45V, Vin = 5.5V 5.0 100 µA µA Logical “0” Input Current Vcc = 45V, Vin = 0.4V “Off” Power Supply Current Vcc = 45V, Vin = 0.8V 2.0 mA “On” Power Supply Current Vcc = 45V, Vin = 2V, Iout = 0mA 8.0 mA Rise Time Vcc = 28V, Vin = 5V, RL = 82Ω 300 ns Fall Time Vcc = 28V, Vin = 5V, RL = 82Ω 1.5 µs Turn on Time Vcc = 28V, Vin = 5V, RL = 82Ω 1.0 µs Turn off Time Vcc = 28V, Vin = 5V, RL = 82Ω 5.2 µs 8.8 26.5 V V -1.0 mA Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCIRCUITS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 www.micropac.com E-MAIL: [email protected] 5/22/02 Pg. 2 of 3 51992 CURRENT DRIVER Schematic and Connection Diagrams 1 R2 CR1 R4 R5 2 3 Q2 CR2 R3 10 Q5 4 R6 1K OHM 9 8 Q3 Q4 6 OUTPUT VCC 10 1 9 INPUT 2 8 E INPUT 3 EXPANDER INPUT RESPONSE TIME CONTROL 4 7 N.C. 6 5 GROUND N.C. Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCIRCUITS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 www.micropac.com E-MAIL: [email protected] 5/22/02 Pg. 3 of 3