53259 400V / 50Ω HERMETICALLY SEALED Features: Applications: • • • • • • • • • • • • • • Mii POWER MOSFET OPTOCOUPLER Hermetically Sealed 8-Pin Dual-In-Line package Normally Closed Contact Performance over –55°C to +125°C Ambient Temperature Range ±400 VDC Blocking Voltage in Bi-directional Mode AC/DC Switching Maximum AC / DC Load Current: 0.12 A / 0.24 A 1500 VDC Withstand Test Voltage Optically Isolated 1.5 A Output Surge Current Same foot print as HSSR 7111 / Mii 53111 • • • • MICROCIRCUITS DIVISION Satellite / Space Systems Military / High Reliability Systems Power Distribution Control AC/DC Electromechanical or Reed Relay Replacement I/O Modules for Automated Test Equipment Process Control Telecom Applications Medical Electronics DESCRIPTION The 53259 is a single channel power MOSFET optocoupler. Low on-resistance of the MOSFET outputs, combined with 1500 VDC isolation between input and output, makes this optocoupler ideal for many solid state relay applications. Operation is specified over the full military temperature range. The part is supplied in an eight-pin, dual-in-line ceramic package, available in variety of quality levels from COTS to class K including any custom screening requirements. The basic data sheet part is environmentally screened to H level in accordance with Table C-IX of MIL-PRF-38534. For ordering part number; consult with Micropac factory for detail. The part is normally shipped with gold plated leads, but lead finishes per MIL-PRF-38534 are available. Functionally, the device operates as a single-pole, normally closed (1 Form B) solid state relay. The device is actuated by an input current, which can be supplied from standard logic types such as open-collector TTL. The input current biases a light emitting diode that is optically coupled to an integrated photovoltaic diode array. The photovoltaic array powers control circuitry that operates the output MOSFETs. Optimum switching of either AC or DC loads is provided by a configurable output. For AC loads, connection A in Figure 1 must be used. Connection A will also switch DC loads but connection B, in Figure 1, provides DC-only operation with the advantages of substantial reduction in on-resistance and twice the output current capability as that obtained with connection A. Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCIRCUITS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 www.micropac.com E-MAIL: [email protected] 7/29/02 Pg. 1 of 6 53259 Power MOSFET Optocoupler ___________________________________________________________________________________________ ABSOLUTE MAXIMUM RATINGS Storage Temperature Range ..................................................................................................................-65°C to +150°C Operating Ambient Temperature - TA .....................................................................................................-55°C to +125°C Junction Temperature - TJ........................................................................................................................................150°C Lead Solder Temperature (1.6mm below seating plane for 10 seconds) ............................................................260°C Average Input Current - IF ........................................................................................................................................20 mA Peak Repetitive Input Current - IFpk (Pulse Width < 100ms; duty cycle < 50%) ..................................................40 mA Peak Surge Input Current - IFPK surge (Pulse Width < 0.2ms; duty cycle < 0.1%) ..........................................100 mA Reverse Input Voltage - VR ....................................................................................................................................5 V Output Current Connection A – IO.......................................................................................................................................... 0.12 A Connection B - IO .......................................................................................................................................... 0.24 A Inrush Output Current Connection A - IOpk surge … ........................................................................................................................... 1.5 A Output Blocking Voltage Connection A - VO ..................................................................................................................................± 400 VDC Connection B - VO ........................................................................................................................ 0 V to +400 VDC Output Power Dissipation ..............................................................................................................................500 mW RECOMMENDED OPERATING CONDITIONS: PARAMETER SYMBOL MIN MAX UNITS Input Current (off) IF (OFF) 5 20 mA Input Voltage (on) VF (ON) 0 0.6 VDC TA -55 +125 °C Operating Temperature Note: On state means contact closed. Off state means contact open. Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCIRCUITS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 www.micropac.com E-MAIL: [email protected] 7/29/02 Pg. 2 of 6 53259 Power MOSFET Optocoupler ___________________________________________________________________________________________ ELECTRICAL SPECIFICATIONS TA = -55°C to +125°C, unless otherwise specified. Parameter Output Blocking Voltage Sym. Min. Typ.* Max. Units VO(OFF) 400 ---- ---- V Test Conditions IF = 10 mA IO = 10 µA IF = 0 mA Output On-Resistance ---- (Connection A) 25 50 Ω Output On-Resistance IO = 120 mA Figure 3 IF = 0 mA ---- (Connection B) 2 (pulse duration ≤ 30 ms) R(ON) Notes 12 25 Ω IO = 240 mA (pulse duration ≤ 30 ms) IO (OFF) ---- 0.2 10 µA VO(OFF) = 400 V Input Forward Voltage VF 1.0 1.2 1.9 V IF = 10 mA Input Reverse Breakdown Voltage VR 5.0 12 ---- V IR = 10 µA Output Leakage Current RH ≤ 45%, t = 5 s Input-Output Insulation II-O ---- ---- 1.0 µA VI-O = 1500 VDC 3, 4 TA = 25°C Turn-On Time tON ---- 0.3 3.0 ms Turn-Off time tOFF ---- 0.1 1.0 ms IF = 0 mA IO = 120 mA IF = 10 mA IO = 120 mA Figure 3 Figure 3 * All typical values are at TA = 25ºC, unless otherwise specified. Notes: 1. Maximum junction to case thermal resistance (θJC) for the device is 15ºC/W, where case temperature (TC), is measured at the center of the package bottom. 2. During the pulsed R(ON) measurement (IO duration < 30 ms), ambient (TA) and case temperature (TC) are equal. 3. Pins 2 through 3 shorted together and pins 5 through 8 shorted together. 4. This is a momentary withstand test, not an operating condition. 5. Care should be taken not to exceed the maximum output power dissipation, maximum case temperature, and maximum junction temperature when repetitively switching loads. Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCIRCUITS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 www.micropac.com E-MAIL: [email protected] 7/29/02 Pg. 3 of 6 53259 Power MOSFET Optocoupler ___________________________________________________________________________________________ Terminal number Terminal symbol 1 2 3 4 5 6 7 8 Connection A (AC or DC load) Conneciton B (DC load only) NC V F+ V FNC VONC NC VO+ NC V F+ V FNC V O+ V OV OV O+ NC = No connection CONNECTION A AC/DC CONNECTION CONNECTION B DC CONNECTION IO IO 1 IF + VF - 2 8 7 + VO 3 6 4 5 8 1 IF + VF - - 2 7 3 6 4 5 + VO - Figure 1. Terminal Connections INPUT OUTPUT OFF ON ON OFF Figure 2. True Table Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCIRCUITS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 www.micropac.com E-MAIL: [email protected] 7/29/02 Pg. 4 of 6 53259 Power MOSFET Optocoupler ________________________________________________________________________________________ V DD PULSE GEN (SEE NOTE 1) RL 1 8 2 7 3 6 4 5 VO MONITOR NODE IF + VF IF MONITOR C L = 25 pF (SEE NOTE 2) RM 200 GND GND 50% 50% IF PULSE = 15 ms WIDTH 90% 10% VO t OFF t ON NOTES: 1. PULSE GENERATOR HAS THE FOLLOWING CHARACTERISTICS: OUTPUT IMPEDANCE = 50 AND t r = t f = 5.0 ns. 2. LOAD CAPACITANCE (C L) INCLUDES PROBE AND JIG CAPACITANCE. Figure 3. Switching Test Circuit and Waveform. Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCIRCUITS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 www.micropac.com E-MAIL: [email protected] 7/29/02 Pg. 5 of 6 53259 Power MOSFET Optocoupler ___________________________________________________________________________________________ Case Outlines Case Outlines CASE OUTLINE P 31757 USA .310 (7.87) .290 (7.37) .320 (8.13) MAX. ESD SYMBOL PIN 1 .050 (1.27) .035 (0.89) .390 (9.91) .370 (9.41) .110 (2.79) .090 (2.29) .170 (4.32) MAX. .020 (0.51) MAX. CASE OUTLINE X .050 (1.27) .035 (0.89) .390 (9.91) .370 (9.41) .170 (4.32) MAX. .320 (8.13) MAX .047 (1.19) TYP .390 (9.91) .380 (7.87) .110 (2.79) .090 (2.29) .020 (.051) MAX. .180 (4.57) MAX SEATING PLANE NOTES: 1. PIN 1 IS INDICATED BY THE ESD TRIANGLE MARKED ON THE LID OF THE PACKAGE. 2. DIMENSIONS ARE IN INCHES, (mm). 3. METRIC EQUIVALENTS ARE GIVEN FOR GENERAL INFORMATION ONLY. 4. UNLESS OTHERWISE SPECIFIED, TOLERANCE IS ±.005 (0.13mm). Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCIRCUITS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 www.micropac.com E-MAIL: [email protected] 7/29/02 Pg. 6 of 6