isl1572 - ISL1572 - Power Line Communication (PLC)

ISL1572
ESIGNS
NEW D
R
O
F
PART
ED
EMENTData Sheet
MME N D
C
O
A
C
L
E
P
R
D RE
NOT
MENDE L1571
R E C OM
IS
To request the full datasheet, please visit www.intersil.com/products/isl1572
July 2, 2009
FN6536.2
Power Line Communication (PLC)
Features
The ISL1572 is a dual operational amplifier designed for
PLC line driving in OFDM and SSC based solutions. This
device features a high drive capability of 750mA while
consuming only 6mA of supply current per amplifier and
operating from a single 4.5V to 12V supply. The driver
achieves a typical distortion of -80dBc, at 150kHz into a 25
load.
• 21dBm output power capability
The ISL1572 is available in the thermally-enhanced
16 Ld QFN or 10 Ld HMSOP package and is specified for
operation over the full -40°C to +85°C temperature range.
The ISL1572 has control pins BIAS0 and BIAS1 for
controlling the bias and enable/disable of the outputs. These
controls allow for lowering the power to fit the
performance/power ratio for the application.
• -80dBc typical driver output distortion at 10MHz
• Drives up to 750mA from a +12V supply
• 20VP-P differential output drive into 21
• Very low noise floor
• -75dBc typical driver output distortion at 4MHz
• -79dBc typical driver output distortion at 17MHz
• Low quiescent current of 6mA per amplifier
• Supply range
- For ISL1572IUEZ 4.5V to 12V
- For ISL1572IRZ ±2.25V to ±6V, 4.5V to 12V
• 250MHz bandwidth
• Thermal shutdown
• Pb-free (RoHS compliant)
Applications
• UPA digital home standard
Ordering Information
PART NUMBER
(Note)
PART
MARKING
TEMP. RANGE
(°C)
PACKAGE
(Pb-Free)
PKG.
DWG. #
ISL1572IRZ
157 2IRZ
-40 to +85
16 Ld QFN
MDP0046
ISL1572IRZ-T7*
157 2IRZ
-40 to +85
16 Ld QFN (Tape and Reel)
MDP0046
ISL1572IUEZ
BBBFA
-40 to +85
10 Ld HMSOP
MDP0050
ISL1572IUEZ-T7*
BBBFA
-40 to +85
10 Ld HMSOP (Tape and Reel)
MDP0050
*Please refer to TB347 for details on reel specifications.
NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100%
matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations).
Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J
STD-020.
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2008, 2009. All Rights Reserved.
All other trademarks mentioned are the property of their respective owners.
ISL1572
Pinouts
OUTA
NC
VS+
OUTB
ISL1572
(16 LD QFN)
TOP VIEW
16
15
14
13
NC 1
ISL1572
(10 LD HMSOP)
TOP VIEW
12 NC
INA- 2
11 INBVS-*
INA+ 3
10 INB+
GND 4
5
6
7
8
NC
NC
VS-
BIAS0
9
VS+ 1
10 OUTB
NC 2
9 INB-
OUTA 3
VS-*
8 INB+
INA- 4
7 BIAS1
INA+ 5
6 BIAS0
BIAS1
*THERMAL PAD MUST BE CONNECTED TO NEGATIVE SUPPLY: VS-.
QFN PACKAGE CAN BE USED IN SINGLE AND DUAL SUPPLY
APPLICATIONS.
*THERMAL PAD MUST BE CONNECTED TO NEGATIVE SUPPLY: VS-.
HMSOP PACKAGE CAN BE USED IN SINGLE SUPPLY APPLICATIONS
ONLY.
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9001 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
2
FN6536.2
July 2, 2009