Date: 13.08.2011 IXYS Data Sheet Issue: 1 Dual Diode Modules MD#710-22N2-26N2 Absolute Maximum Ratings VRRM VDRM [V] MDD MDA MDK 2200 710-22N2 710-22N2 710-22N2 2400 710-24N2 710-24N2 710-24N2 2600 710-26N2 710-26N2 710-26N2 VOLTAGE RATINGS VDRM VDSM VRRM VRSM Repetitive peak off-state voltage 1) Non-repetitive peak off-state voltage Repetitive peak reverse voltage 1) 1) Non-repetitive peak reverse voltage 1) OTHER RATINGS MAXIMUM LIMITS UNITS 2200-2600 V 2300-2700 V 2200-2600 V 2300-2700 V MAXIMUM LIMITS UNITS IF(AV)M Maximum average on-state current, TC = 85°C 2) 708 A IF(AV)M Maximum average on-state current. TC = 100°C 2) 587 A 1440 A 1198 A 12.7 kA IF(RMS)M Nominal RMS on-state current, TC = 55°C IF(d.c.) D.C. on-state current, TC = 55°C 2) IFSM Peak non-repetitive surge tp = 10 ms, VRM = 60%VRRM IFSM2 Peak non-repetitive surge tp = 10 ms, VRM ≤ 10V 2 2 3) 3) 3) 14 kA 3 806 x 10 A2s 980 x 103 A2s 3000 V It I t capacity for fusing tp = 10 ms, VRM = 60%VRRM I2 t I2t capacity for fusing tp = 10 ms, VRM ≤ 10 V 3) VISOL Isolation Voltage 4) Tvj op Operating temperature range -40 to +150 °C Tstg Storage temperature range -40 to +150 °C Notes: 1) De-rating factor of 0.13% per °C is applicable for Tvj below 25°C. 2) Single phase; 50 Hz, 180° half-sinewave. 3) Half-sinewave, 150°C Tvj initial. 4) AC RMS voltage, 50 Hz, 1min test Rating Report. Types MD#710-22N2 and MD#710-26N2 Issue 1 Page 1 of 9 August, 2011 IXYS Diode Module Types MD#710-22N2 to MD#710-26N2 Characteristics PARAMETER MIN. TYP. MAX. TEST CONDITIONS 1) UNITS VFM Maximum peak on-state voltage - - 1.36 VT0 Threshold voltage - - 0.80 V rT Slope resistance - - 0.35 mΩ IRRM Peak reverse current - - 50 Qrr Recovered Charge - 1900 2125 Qra Recovered Charge, 50% chord - 1700 - Irm Reverse recovery current - 150 - trr Reverse recovery time, 50% chord - 23 - RthJC Thermal resistance, junction to case - - 0.062 Single Diode K/W - - 0.031 Whole Module K/W RthCH Thermal resistance, case to heatsink - - 0.02 Single Diode K/W - - 0.01 Whole Module K/W 5.1 - 6.9 Nm 10.8 - 13.2 Nm - 1.5 - kg F1 Mounting force (to heatsink) 2) F2 Mounting force (to terminals) Wt Weight 2) IFM = 1570A Rated VRRM V mA µC µC ITM = 1000 A, tp =1ms, di/dt =10A/µs, VR =100 V A µs Notes: 1) Unless otherwise indicated Tvj=150°C. 2) Screws must be lubricated. Rating Report. Types MD#710-22N2 and MD#710-26N2 Issue 1 Page 2 of 9 August, 2011 IXYS Diode Module Types MD#710-22N2 to MD#710-26N2 Notes on Ratings and Characteristics 1.0 Voltage Grade Table VRRM V 2200 2400 2600 Voltage Grade 22 24 26 VRSM V 2300 2500 2700 VR DC V 1650 1800 1950 2.0 Extension of Voltage Grades This report is applicable to other voltage grades when supply has been agreed by Sales/Production. 3.0 De-rating Factor A blocking voltage de-rating factor of 0.13%/°C is applicable to this device for Tvj below 25°C. 4.0 Snubber Components When selecting snubber components, care must be taken not to use excessively large values of snubber capacitor or excessively small values of snubber resistor. Such excessive component values may lead to device damage due to the large resultant values of snubber discharge current. If required, please consult the factory for assistance. 5.0 Computer Modelling Parameters 5.1 Device Dissipation Calculations I AV = WAV = − VT 0 + VT 0 + 4 ⋅ ff ⋅ rT ⋅ WAV 2 ⋅ ff 2 ⋅ rT 2 2 and: ∆T Rth ∆T = T j max − TK Where VT0 = 0.8 V, rT = 0.35 mΩ. Rth = Supplementary thermal impedance, see table below and ff = Form factor, see table below. Supplementary Thermal Impedance Conduction Angle 30° 60° 90° 120° 180° 270° d.c. Square wave 0.0702 0.0685 0.0679 0.0668 0.0658 0.0637 0.0620 Sine wave 0.0677 0.0673 0.0664 0.0655 0.0650 Form Factors Conduction Angle 30° 60° 90° 120° 180° 270° d.c. Square wave 3.464 2.449 2 1.732 1.414 1.149 1 Sine wave 3.98 2.778 2.22 1.879 1.57 Rating Report. Types MD#710-22N2 and MD#710-26N2 Issue 1 Page 3 of 9 August, 2011 IXYS Diode Module Types MD#710-22N2 to MD#710-26N2 5.2 Calculating VF using ABCD Coefficients The on-state characteristic IF vs. VF, on page 6 is represented in two ways: (i) The well established VT0 and rT tangent used for rating purposes (ii) A set of constants A, B, C, D, forming the coefficients of the representative equation for VF in terms of IF given below: VF = A + B ⋅ ln (I F ) + C ⋅ I F + D ⋅ I F The constants, derived by curve fitting software, are given below for both hot and cold characteristics. The resulting values for VF agree with the true device characteristic over a current range, which is limited to that plotted. 25°C Coefficients 150°C Coefficients A 0.9793297 A 0.5657172 B 0.02691659 B 0.03677309 C 1.928214e -4 C 3.198422e-4 D 7.102171e-4 D 3.316503e-4 Rating Report. Types MD#710-22N2 and MD#710-26N2 Issue 1 Page 4 of 9 August, 2011 IXYS Diode Module Types MD#710-22N2 to MD#710-26N2 5.3 D.C. Thermal Impedance Calculation −t ⎛ τ rt = ∑ rp ⋅ ⎜1 − e p ⎜ p =1 ⎝ p=n ⎞ ⎟ ⎟ ⎠ Where p = 1 to n and: n t rt rp τp = number of terms in the series = Duration of heating pulse in seconds = Thermal resistance at time t = Amplitude of pth term = Time Constant of rth term The coefficients for this device are shown in the table below: D.C. Term rp τp 1 2 1.37×10 7.6×10 -3 4.86×10 -4 8.6×10 -3 -3 3 4 5 0.0114 0.0223 0.0221 0.101 0.56 3.12 6.0 Reverse recovery ratings (i) Qra is based on 50% IRM chord as shown in Fig. 1 Fig. 1 150 µs (ii) Qrr is based on a 150 µs integration time i.e. Qrr = ∫i rr .dt 0 (iii) K Factor = t1 t2 Rating Report. Types MD#710-22N2 and MD#710-26N2 Issue 1 Page 5 of 9 August, 2011 IXYS Diode Module Types MD#710-22N2 to MD#710-26N2 Curves Figure 1 – On-state characteristics of Limit device 10000 MD#710-22N2-26N2 Issue 1 Instantaneous Forward current - IFM (A) Tj = 25°C Tj = 150°C 1000 100 0 0.5 1 1.5 2 2.5 3 Instantaneous Forward voltage - VFM (V) Figure 2 – Maximum surge and I2t Ratings Gate may temporarily lose control of conduction angle 1.00E+07 100000 I t: VRRM ≤10V 2 2 I t: 60% VRRM 2 2 Maximum I t (A s) Total peak half sine surge current (A) MD#710-22N2-26N2 Issue 1 Tj (initial) = 150°C 1.00E+06 10000 ITSM: VRRM ≤10V ITSM: 60% VRRM 1000 1 3 5 10 1 Duration of surge (ms) Rating Report. Types MD#710-22N2 and MD#710-26N2 Issue 1 5 10 50 100 1.00E+05 Duration of surge (cycles @ 50Hz) Page 6 of 9 August, 2011 IXYS Diode Module Types MD#710-22N2 to MD#710-26N2 Figure 4 - Recovered charge, Qra (50% chord) Figure 3 - Total recovered charge, Qrr 10000 10000 MD#710-22N2-26N2 Issue 1 Tj=150°C 2000A 1500A Recovered charge - Qra, 50% chord (µC) Recovered charge - Qrr (µC) 2000A 1500A 1000A MD#710-22N2-26N2 Issue 1 Tj=150°C 500A 1000 1000A 500A 1000 1 10 100 1000 1 10 di/dt (A/µs) 1000 Figure 6 - Maximum recovery time, trr (50% chord) Figure 5 - Peak reverse recovery current, Irm 1000 100 di/dt (A/µs) MD#710-22N2-26N2 Issue 1 Tj=150°C 100 2000A 1500A 1000A 500A MD#710-22N2-26N2 Issue 1 Reverse recovery current - Irm (A) Reverse recovery time (50% chord) - trr (µs) Tj=150°C 100 2000A 1500A 1000A 500A 10 1 1 10 100 1000 1 di/dt (A/µs) Rating Report. Types MD#710-22N2 and MD#710-26N2 Issue 1 10 100 1000 di/dt (A/µs) Page 7 of 9 August, 2011 IXYS Diode Module Types MD#710-22N2 to MD#710-26N2 Figure 8 – On-state current vs. Heatsink temperature Figure 7 – On-state current vs. Power dissipation 2500 160 MD#710-22N2-26N2 Issue 1 MD#710-22N2-26N2 Issue 1 140 d.c. 2000 3ø ½ wave Maximum permissible heatsink temperature (°C) Maximum Forward Dissipation (W) 6ø 1500 1000 120 100 80 60 40 500 20 6ø 0 0 500 1000 1500 3ø ½ wave d.c. 0 2000 0 Mean Forward Current (A) (Whole cycle averaged) 500 1000 1500 2000 Mean forward current (A) (Whole cycle averaged) Figure 9 – Transient thermal impedance 0.1 MD#710-22N2-26N2 Issue 1 Single Diode Thermal impedance (K/W) 0.01 0.001 0.0001 0.00001 0.00001 0.0001 0.001 0.01 0.1 1 10 100 Time (s) Rating Report. Types MD#710-22N2 and MD#710-26N2 Issue 1 Page 8 of 9 August, 2011 IXYS Diode Module Types MD#710-22N2 to MD#710-26N2 Outline Drawing & Ordering Information 3 1 2 3 1 2 MDD MDA 3 1 2 MDK 150A123 ORDERING INFORMATION (Please quote 10 digit code as below) M D# 710 Fixed Type Code Configuration code DD, DA, DK Fixed Type Code Voltage code VRRM/100 22-26 N 2 Standard Diode Fixed Version Code Typical order code: MDA710-22N2– MDA configuration, 2200V VRRM IXYS Semiconductor GmbH Edisonstraße 15 D-68623 Lampertheim Tel: +49 6206 503-0 Fax: +49 6206 503-627 E-mail: [email protected] IXYS Westcode Semiconductors Ltd Langley Park Way, Langley Park, Chippenham, Wiltshire, SN25 1GE. Tel: +44 (0)1249 444524 Fax: +44 (0)1249 659448 E-mail: [email protected] www.ixys.com IXYS Corporation 1590 Buckeye Drive Milpitas CA 95035-7418 Tel: +1 (408) 457 9000 Fax: +1 (408) 496 0670 E-mail: [email protected] WESTCODE An IXYS Company www.westcode.com The information contained herein is confidential and is protected by Copyright. The information may not be used or disclosed except with the written permission of and in the manner permitted by the proprietors IXYS Semiconductors GmbH. IXYS Long Beach IXYS Long Beach, Inc 2500 Mira Mar Ave, Long Beach CA 90815 Tel: +1 (562) 296 6584 Fax: +1 (562) 296 6585 E-mail: [email protected] © IXYS Semiconductor GmbH. In the interest of product improvement, IXYS reserves the right to change specifications at any time without prior notice. Rating Report. Types MD#710-22N2 and MD#710-26N2 Issue 1 Page 9 of 9 August, 2011