KOA SPEER ELECTRONICS, INC. TN-196 R14 AHA 3/27/13 Ceramic Chip Capacitors Type NPO, X5R, X7R, Y5V CERTIFIED CERTIFIED 1. General 1-1 Range of Application This document applies to miniaturized ceramic chip capacitors for applications in circuits of electronic devices. 2. Type Designation The type designation shall be the following form: New Type 3. NPO 0805 H T TD 101 K Dielectric Size Voltage Termination Material Packaging Capacitance Code Tolerance NPO X5R X7R Y5V 0402 0603 0805 1206 1210 T: Sn TP: 7" 2mm pitch (0402 only) TD: 7" paper tape TE: 7" embossed plastic TDB: 13" paper tape TEB: 13" embossed plastic NPO, X5R, X7R, Y5V - 2 significant digits + no. of zeros. R indicates decimal point. A C E H I J K = 10V = 16V = 25V = 50V = 100V = 200V = 6.3V B C D F G J K M Z = ±0.1pF = ±0.25pF = ±0.5pF = ±1% = ±2% = ±5% = ±10% = ±20% = +80%, -20% Dimensions and Construction Case Size L W 0402 .02±.004 (0.5±0.1) .021 (0.55) .01±.006 (0.25±0.15) 0603 .063±.006 (1.6±0.15) .032±.006 (0.81±0.15) .035 (0.9) .014±.006 (0.35±0.15) 0805 .079±.008 (2.01±0.2) .049±.008 (1.25±0.2) .051 (1.3) .02±.01 (0.50±0.25) 1206 .126±.008 (3.2±0.2) .063±.008 (1.6±0.2) .059 (1.5) .02±.01 (0.5±0.25) 1210 .126±.008 (3.2±0.2) .098±.008 (2.5±0.2) .067 (1.7) .02±.01 (0.5±0.25) d Ceramic Body Solder Plating (Sn) Ni Plating Electrodes d .039±.004 (1.0±0.1) t d Dimensions inches (mm) W t (Max.) L Cu Metallization PAGE 1 OF 13 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-196 R14 4. Terminations ■ Standard Nickel Barrier ■ Solder Plated 5. Applications and Ratings Voltage Ratings Dissipation Factor T.C.C. Test Voltage Operating Temperature Insulation Resistance 50V 100V 200V For Values >30pF: 0.1% max., ≤30pF: Q = 400 + 20 x C DF = 1/Q C is in pF 0 ± 30 ppm/°C 1.0 ± 0.2 Vrms -55°C to +125°C +25°C 100,000MΩ min. or 1000 MΩ - µF min. whichever is less K: ±10% 6.3V 10V 6.3V = 7.5% max. 10V = 10% max. ±15% (0 VDC) 1.0 ± 0.2 Vrms -55°C to +85°C +25°C 100,000MΩ min. or 500 MΩ - µF min. whichever is less X7R K: ±10% 10V 16V 25V 50V 100V 200V 10V = 10% max. 16V = 3.5% max. 25V, 50V, 100V = 2.5% max. ±15% (0 VDC) 1.0 ± 0.2 Vrms -55°C to +125°C +25°C 100,000MΩ min. or 1000 MΩ - µF min. whichever is less Y5V Z: +80, -20% 10V 16V 25V 50V +22% to -82% max. 1.0 ± 0.2 Vrms -30°C to +85°C +25°C 10,000MΩ min. or 1000 MΩ - µF min. whichever is less Capacitance Tolerance Dielectric .47pF~8.2pF= C:±0.25pF 5.6pF~8.2pF= D±0.5pF 10pF~ 10000pF= F:±1%, G:±2%,J:±5% NPO X5R 16V & 25V = 7.0% 50V = 5.0% For complete environmental specifications, please refer to www.koaspeer.com PAGE 2 OF 13 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-196 R14 6. NPO Capacitance Voltage Availability Size pF 0402* 50 (H) Capacitance values µF Cap. Code 0.47 0.56 0.68 0.82 1 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 39 47 56 68 82 100 120 150 180 220 270 330 390 470 560 680 820 1000 1200 .00000047 .00000056 .00000068 .00000082 .0000010 .0000012 .0000015 .0000018 .0000022 .0000027 .0000033 .0000039 .0000047 .0000056 .0000068 .0000082 .000010 .000012 .000015 .000018 .000022 .000027 .000033 .000039 .000047 .000056 .000068 .000082 .0001 .00012 .00015 .00018 .00022 .00027 .00033 .00039 .00047 .00056 .00068 .00082 .0010 .0012 0805 0603* 50 (H) 50 (H) 100 (I) 1206 100 (I) 200 (J) 50 (H) 100 (I) 200 (J) R47 R56 R68 R82 1R0 1R2 1R5 1R8 2R2 2R7 3R3 3R9 4R7 5R6 6R8 8R2 100 120 150 180 220 270 330 390 470 560 680 820 101 121 151 181 221 271 331 391 471 561 681 821 102 122 Capacitance tolerance available: .47pF~8.2pF = C: ±0.25pF 5.6pF~8.2pF = D: ±0.5pF 10pF~10000pF = F: ±1%, G: ±2%, J: ±5% PAGE 3 OF 13 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-196 R14 7. X5R Capacitance Voltage Availability Size 0402 Capacitance values pF µF Cap. Code 56000 68000 82000 100000 120000 150000 180000 220000 270000 330000 470000 560000 680000 820000 1000000 1200000 1500000 1800000 2200000 3300000 4700000 6800000 10000000 22000000 47000000 100000000 0.056 0.068 0.082 0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 3.3 4.7 6.8 10 22 47 100 10 (A) 0603 6.3 (K) 10 (A) 0805 1206 1210 6.3 (K) 10 (A) 10 (A) 563 683 823 104 124 154 184 224 274 334 474 564 684 824 105 125 155 185 225 335 475 685 106 226 476 107 Capacitance tolerance available: ±10% PAGE 4 OF 13 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-196 R14 8. X7R Capacitance Voltage Availability 0402 Size Capacitance values 10 16 25 50 10 pF µF Cap. Code (A) (C) (E) (H) (A) 100 120 150 180 220 270 330 390 470 560 680 820 1000 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 10000 12000 15000 18000 22000 27000 33000 39000 47000 56000 68000 82000 100000 120000 150000 180000 220000 270000 330000 390000 470000 560000 680000 1000000 1200000 1500000 1800000 2200000 3900000 4700000 .0001 .00012 .00015 .00018 .00022 .00027 .00033 .00039 .00047 .00056 .00068 .00082 .0010 .0012 .0015 .0018 .0022 .0027 .0033 .0039 .0047 .0056 .0068 .0082 .010 .012 .015 .018 .022 .027 .033 .039 .047 .056 .068 .082 .100 .120 .150 .180 .220 .270 .330 .390 .470 .560 .680 1.00 1.20 1.50 1.80 2.20 3.90 4.70 0603 0805 16 25 (C) (E) 50 (H) 10 16 (A) (C) 25 (E) 1206 50 100 200 10 16 (H) (I) (J) (A) (C) 1210 50 100 200 50 100 200 (H) (I) (J) (H) (I) (J) 101 121 151 181 221 271 331 391 471 561 681 821 102 122 152 182 222 272 332 392 472 562 682 822 103 123 153 183 223 273 333 393 473 563 683 823 104 124 154 184 224 274 334 394 474 564 684 105 125 155 185 225 395 475 Capacitance tolerance available: ±10% PAGE 5 OF 13 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-196 R14 9. Y5V Capacitance Voltage Availability 0402 Size Capacitance values pF 2200 2700 3300 3900 4700 5600 6800 8200 10000 12000 15000 18000 22000 27000 33000 39000 47000 56000 68000 82000 100000 120000 150000 180000 220000 270000 330000 390000 470000 560000 680000 820000 1000000 1200000 1500000 1800000 2200000 2700000 3300000 3900000 4700000 5600000 6800000 10000000 22000000 µF .0022 .0027 .0033 .0039 .0047 .0056 .0068 .0082 .010 .012 .015 .018 .022 .027 .033 .039 .047 .056 .068 .082 .100 .120 .150 .180 .220 .270 .330 .390 .470 .560 .680 .820 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 10 22 Cap. Code 222 272 332 392 472 562 682 822 103 123 153 183 223 273 333 393 473 563 683 823 104 124 154 184 224 274 334 394 474 564 684 824 105 125 155 185 225 275 335 395 475 565 685 106 226 16 (C) 0603 16 (C) 25 (E) 0805 10 (A) 50 (H) 16 (C) 1206 25 (E) 50 (H) 10 (A) 16 (C) 25 (E) 50 (H) Capacitance tolerance available: +80%, -20% PAGE 6 OF 13 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-196 R14 10. Typical Impedance Characteristics - NPO Variation of Impedance with Cap Value Impedance vs. Frequency 0805 - C0G (NP0) 10 pF vs. 100 pF vs. 1000 pF ∆ Capacitance vs. Frequency 100,000 +2 % ∆ Capacitance Impedance, Ω 10,000 1,000 100 10 pF 10.0 +1 0 -1 -2 1.0 1kHz 10 kHz 100 pF 1000 pF 0.1 1 100 10 100 kHz 1 MHz 10 MHz Frequency 1000 Frequency, MHz Insulation Resistance (Ohm-Farads) % ∆ Capacitance Temperature Coefficient Typical Capacitance Change Envelope: 0 ± 30 ppm/°C +0.5 0 -0.5 -55 -35 -15 +5 +25 +45 +65 +85 +105 +125 Insulation Resistance vs Temperature 10,000 1,000 100 0 +20 Temperature °C +40 +60 +80 +100 Temperature °C Variation of Impedance with Ceramic Formulation Impedance vs. Frequency 1000 pF - C0G (NP0) vs X7R 0805 Variation of Impedance with Chip Size Impedance vs. Frequency 1000 pF - C0G (NP0) 10 10.00 1206 0805 1812 1210 X7R NPO Impedance, Ω Impedance, Ω +25 1.0 0.1 10 100 1.00 0.10 0.01 10 1000 100 Frequency, MHz 1000 Frequency, MHz PAGE 7 OF 13 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-196 R14 11. Typical Impedance Characteristics - X5R Insulation Resistance (Ohm-Farads) Temperature Coefficient +20 %∆ Capacitance +15 +10 +5 0 -5 -10 -15 -20 -60 -40 -20 0 +20 +40 +60 +80 Insulation Resistance vs Temperature 10,000 1,000 100 0 +20 Temperature °C +25 +40 +60 +80 +100 Temperature °C PAGE 8 OF 13 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-196 R14 12. Typical Impedance Characteristics - X7R Variation of Impedance with Cap Value Impedance vs. Frequency 1,000 pF vs. 10,000 pF - X7R 0805 ∆ Capacitance vs. Frequency 10.00 1,000 pF +20 % ∆ Capacitance Impedance, Ω 10,000 pF 1.00 0.10 0.01 10 100 1000 +10 0 -10 -20 1kHz 10 kHz 100 kHz Frequency, MHz Insulation Resistance (Ohm-Farads) Temperature Coefficient +12 %∆ Capacitance +6 0 -6 -12 -18 -24 -75 -50 -25 0 10 MHz +25 +50 +75 +100 +125 Insulation Resistance vs Temperature 10,000 1,000 100 0 +20 Temperature °C +40 +25 +60 +80 +100 Temperature °C Variation of Impedance with Chip Size Impedance vs. Frequency 100,000 pF - X7R Variation of Impedance with Chip Size Impedance vs. Frequency 10,000 pF - X7R 10 10 1206 0805 1210 Impedance, Ω Impedance, Ω 1 MHz Frequency 1.0 0.1 .01 1 100 10 1206 0805 1210 1.0 0.1 .01 1,000 1 10 Frequency, MHz 100 1,000 Frequency, MHz PAGE 9 OF 13 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-196 R14 13. Typical Impedance Characteristics - Y5V 0.1 µF - 0603 Impedance vs. Frequency 0.22 µF - 0805 Impedance vs. Frequency 1,000 10,000 1,000 Impedance (Ω) Impedance (Ω) 100 10 1 0.1 100 10 1 0.1 0.01 10,000 100,000 1,000,000 0.01 10,000 10,000,000 100,000 Insulation Resistance (Ohm-Farads) % ∆ Capacitance Temperature Coefficient +20 +10 0 -10 -20 -30 -40 -50 -60 -70 -80 -55 -35 -15 +5 +25 +45 +65 +85 +105 +125 Insulation Resistance vs. Temperature 10,000 1,000 100 0 +20 +30 Temperature °C +40 +50 +60 +70 +80 +85 Temperature °C Capacitance Change vs. DC Bias Voltage 1 µF - 1206 Impedance vs. Frequency 1,000 10,000,000 1,000,000 Frequency (MHz) Frequency (MHz) +40 +20 ∆ c/c (%) Impedance (Ω) 100 10 1 0 -20 -40 -60 0.1 -80 0.01 10,000 100,000 1,000,000 -100 0 10,000,000 20 40 60 80 100 DC Bias Voltage Frequency (MHz) PAGE 10 OF 13 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-196 R14 14. Tape and Reel Quantities All tape and reel specifications are in compliance with RS481. Size Dielectric Voltage Cap. Range 0402 0603 All All NPO X5R All All All All 200 200 100 100 50 50 50 25 25 16 16 16 10 50 50 25 25 16 10 X7R 0805 Y5V All All All All 472 682 < = 103 153 ~ 223 < = 223 273 ~ 563 104 < = 333 393 ~ 104 473 ~ 683 823 ~ 274 334 ~ 474 684 ~ 105 103 ~ 104 224 103 ~ 104 154 ~ 224 474, 105 All TP TD TE TDB TEB 10000 ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– 4000 4000 ––– 4000 ––– 4000 4000 4000 4000 4000 4000 4000 4000 4000 ––– ––– 4000 4000 4000 4000 4000 ––– ––– ––– ––– 3000 ––– 3000 ––– ––– ––– ––– ––– ––– ––– ––– ––– 3000 3000 ––– ––– ––– ––– ––– 3000 ––– 15000 20000 ––– 15000 ––– 20000 15000 20000 15000 15000 20000 15000 20000 15000 ––– ––– 20000 15000 20000 15000 15000 ––– ––– ––– ––– ––– ––– 10000 ––– ––– ––– ––– ––– ––– ––– ––– ––– 10000 10000 ––– ––– ––– ––– ––– 10000 Size Dielectric Voltage 200 200 100 50 10 100 100 100 200 200 50 50 16 16 10 50 50 50 25 25 25 16 10 10 10 50 50 100 200 NPO X5R X7R 1206 Y5V * TP is a 7" reel with a 2mm pitch, TD & TE are 7" reels, TDB & TEB are 13" reels X5R 1210 X7R Cap. Range TD TE TDB TEB < = 151 221 ~ 102 < = 471 < = 471 475, 106 < = 473 683 104 < = 153 223 < = 124 154 ~ 224 < = 394 474 ~ 105 225 ~ 275 104 ~ 224 334 ~ 474 684 104 ~ 224 334 ~ 684 225 105 335 ~ 475 226 106 123 ~ 333 823 ~ 224 473 ~ 823 223 ~ 473 4000 4000 4000 4000 ––– 4000 ––– ––– 4000 ––– 4000 ––– 4000 ––– ––– 4000 4000 ––– 4000 4000 ––– 4000 ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– 3000 ––– 4000 2000 ––– 3000 ––– 3000 ––– 3000 3000 ––– ––– 3000 ––– ––– 3000 ––– 3000 2500 2000 4000 3000 4000 3000 20000 15000 20000 20000 ––– 15000 ––– ––– 15000 ––– 15000 ––– 15000 ––– ––– 20000 15000 ––– 20000 15000 ––– 15000 ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– 10000 ––– 10000 ––– 10000 10000 ––– ––– 10000 ––– ––– 10000 ––– 10000 7000 ––– 10000 10000 10000 10000 15. Reel Specifications 1.575 (40) min. Access hole at slot location. W3 (Includes flange distortion at outer edge). W2 (Measured at hub). B* Reel Dimensions Tape Size(1) (Arbor hole dia.) C A Max. B* Min. Dimensions inches (mm) D* N C W1 Min. Min. ± .060 A D* .331 - 0.0 8mm N (Hub dia.) 12.992 (330) Full radius* 0.059 (1.5) W1 (Measured at hub). 0.512 ± 0.008 (13.0 ± 0.20) (8.4 .795 (20.2) * Drive spokes optional. If used, asterisked dimensions apply. .567 14.4 1.969 (50) .488 ±.076 - 0.0 12mm Tape slot in core for tape start. 0.98 (2.5) min. width, .394 (10) min. depth. ±1 - 0) W2 Max. (12.4 ±- 20 ) .724 (18.4) W3 .311 (7.9 Min.) .429 (10.9 Max.) .469 (11.9 Min.) .607 (15.4 Max.) Metric dimensions will govern. English measurements rounded and for reference only. (1) For tape sizes 16mm and 24mm (used with chip size 3640) consult EIA RS-481 latest revision. PAGE 11 OF 13 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-196 R14 16. Carrier Tape Specifications Embossed plastic 8 & 12mm 10 pitches cumulative tolerance on tape ±0.008 (±0.2) T2 T P0 Embossment P2 D0 Deformation between embossments 20° E B1 K0 Top cover tape Maximum Component Rotation G1 See note 3 A0 Side or Front Sectional View Example “A” F W B0 T1 20° Maximum Component Rotation G2 See note 4 Typical component cavity center line P1 Center lines of cavity For tape feeder reference only including draft concentric around B0 BO D1 for components .079 x .047 (2.0 x 1.2) and larger Maximum cavity size, see note 1 User direction of feed AO Typical component center line Top View Example “B” Dimensions inches (mm) Tape Size Constant D0 E P0 P2 T Max. T1 G1 G2 8mm, 12mm .059 ±.004 - 0.0 (1.5 ±- 0.10 0.0 ) .069 ± .004 (1.75 ±0.10) .157 ± .004 (4.0 ± 0.10) .079 ± .002 (2.0 ± 0.05) .024 (0.600) .004 (0.10) Max. .030 (0.75) Min. See note 3 .030 (0.75) Min. See note 4 B1 Max. See note 6 D1 Min. See note 5 T2 W A0B0K0 .098 (2.5 Max.) .256 (6.5 Max.) .098 (2.5 Max.) .256 (6.5 Max.) ± ± - See note 1 Tape Size Variable 8mm .179 (4.55) .323 (8.2) .179 (4.55) .323 (8.2) 12mm 12mm 1/2 Pitch 12mm Double Pitch .039 (1.0) .059 (1.5) .039 (1.0) .059 (1.5) Dimensions inches (mm) R Min. P1 See note 2 F .138 ± .002 (3.5 ± 0.05) .217 ± .002 (5.5 ± 0.05) .138 ± .002 (3.5 ± 0.05) .217 ± .002 (5.5 ± 0.05) .157 ± .004 (4.0 ± 0.10) .157 ± .004 (4.0 ± 0.10) .079 ± .004 (2.0 ± 0.10) .315 ± .004 (8.0 ± 0.10) .984 (25) 1.181 (30) .984 (25) 1.181 (30) .012 .004 0.3 0.1 .315 (8.0 ) .472 ± .012 (12.0 ± .30) .315 ±- .012 .004 (8.0 ±- 0.3 0.1) .472 ± .012 (12.0 ± .30) See note 1 See note 1 See note 1 Notes: 1. A0, B0 and K0 are determined by the max. dimensions to the ends of the terminals extending from the components body and/or the body of the component. The clearance between the end of the terminals of the body of the components to the sides and depth of the cavity (A0, B0 and K0) must be within .002" (0.05)mm min. and .020" (0.50)mm max. The clearance allowed must also prevent rotation of the component within the cavity of not more than 20 degrees (see examples A & B). 2. Tape with components shall pass around radius "R" without damage. The minimum trailer length (Note 2 Fig. 3) may require additional length to provide R min. for .472" (12)mm embossed tape for reels with hub diameters approaching N min. (Table 4). 3. G1 dimension is the flat area from the edge of the sprocket hole to either the outward deformation of the carrier tape between the embossed cavities or to the edge of the cavity whichever is less. 4. G2 dimension is the flat area from the edge of the carrier tape opposite the sprocket holes to either the outward deformation of the carrier tape between the embossed cavity or to the edge of the cavity whichever is less. 5. The embossed hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and hole location shall be applied independent of each other. 6. B1 dimension is a reference dimension for tape feeder clearance only. PAGE 12 OF 13 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-196 R14 17. Carrier Tape Specifications Punched paper tape 8 & 12mm 10 pitches cumulative tolerance on tape ±0.008 (±0.2) T P0 P2 D0 20° Maximum Component Rotation E F Top cover tape Bottom cover tape B0 T1 T1 Typical component center line Maximum Component Rotation AO Side or Front Sectional View Example “C” P1 Top View Example “D” G2 Center lines of cavity User direction of feed 20° G1 A0 Cavity size, see note 1 Typical component cavity center line BO T W Carrier Tape Dimensions Tape Size Constant D0 8mm 12mm Tape Size Variable E P0 .059 - .000 (1.5 ±- 0.1 0.0 ) .069 ± .004 (1.75 ±0.10) .157 ± .004 (4.0 ± 0.10) P1 F .157 ± .004 (4.0 ± 0.10) .157 ± .004 (4.0 ± .010) .079 ± .004 (2.0 ± 0.10) .315 ± .004 (8.0 ± .010) .138 ± .002 (3.5 ± 0.05) .217 ± .002 (5.5 ± 0.05) .138 ± .002 (3.5 ± 0.05) .217 ± .002 (5.5 ± 0.05) ±.004 8mm 12mm 8mm 1/2 Pitch 12mm Double Pitch Dimensions inches (mm) P2 T1 .004 .079 ± .002 (0.10) (2.0 ± 0.05) Max. Dimensions inches (mm) W A0B0 G1 .030 (0.75) Min. T ± .012 .315 - .004 (8.0 ±- 0.3 0.1 ) .472 ± .012 (12.0 ± 0.3) .315 ±- .012 .004 (8.0 ±- 0.3 0.1 ) .472 ± .012 (12.0 ± 0.3) See note 1 See note 3 .030 (0.75) Min. .984 (25) See note 2 Notes: 1. A0, B0 and T are determined by the max. dimensions to the ends of the terminals extending from the component body and/or the body dimensions of the component. The clearance between the ends of the terminals or body of the components to the sides and depth of the cavity (A0, B0 and T) must be within .002" (0.05) mm min. and .020" (0.50) mm max. The clearance allowed must also prevent rotation of the component within the cavity of not more than 20 degrees (see examples C & D). 2. Tape with components shall pass around radius "R" without damage. 3. .043" (1.1) mm base tape and .063" (1.6) mm max. for non-paper base compositions. 18. Recommended Land Pattern Dimensions Component pads should be designed to achieve good solder filets and minimize component movement during reflow soldering. Pad dimensions are given below for multilayer ceramic capacitors for both reflow and wave soldering. The basis for these designs is: Dimensions inches (mm) Case Size 0402 • Pad width equal to component width. It is permissible to decrease this to as low as 85% of component width but it is not advisable to go below this. 0603 • Pad overlap 0.5mm beneath component 0805 • Pad extension 0.5mm beyond components for reflow and 1.0mm for wave soldering C D 1206 C 1210 A B C D 0.02 (0.50) 0.03 (0.75) 0.05 (1.25) 0.06 (1.60) 0.10 (2.50) 0.07 (1.70) 0.09 (2.30) 0.12 (3.00) 0.16 (4.00) 0.16 (4.00) 0.02 (0.60) 0.03 (0.80) 0.04 (1.00) 0.04 (1.00) 0.04 (1.00) 0.02 (0.50) 0.03 (0.70) 0.04 (1.00) 0.09 (2.00) 0.09 (2.00) A B PAGE 13 OF 13 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.