CYG2000

CYG20xx
CybergateTM DAA
INTEGRATED CIRCUITS DIVISION
Features
Description
• Low Distortion Transformer Signal Coupling
(0.01% max)
• Complete Ring Detector Circuit
• Low Power Hook Switch
• Electronic Inductor/Gyrator Circuit
• Surge Protection
• Transient Protection Zener Diodes
• Half- (20X0) or Full- (20X1) Wave Detection
• V.32 bis /V.34 Compatible
• FCC Compatible
• Compatible with U.S. and Canadian Dial-Up Phone
Lines
• Supports Leased-Line Operation
• PC board mountable
The CYG2000, CYG2011, and CYG2020 are Data
Access Arrangement (DAA) modules featuring a 350V,
120mA, 15 relay used for hook switch; an
optocoupler with minimum CTR of 33% for ring
detection; and a low-distortion transformer with
28.8kbps capabilities.
Part
Description
Applications
CYG2000
DAA Module, Half Wave Ring Detection
•
•
•
•
•
•
•
•
•
•
•
CYG2011
DAA Module, Full Wave Ring Detection,
Loop Current Detection
CYG2020
DAA Module, Half Wave Ring Detection, CID
Approvals
UL Recognized: File E174201
Ordering Information
Modems
Fax Machines
Remote Data Acquisition
Security Systems
Voice Mail Systems
PC Motherboard
Computer Telephony
Process Control
Medical
PBX
Direct Broadcast Satellite
Block Diagrams
CYG2011
CYG2000
18
LINE 2
10
2
RING
LINE 1
RING
LINE 2
GYRATOR
HOOKSWITCH
OH
VCC
RING
VCC DETECT
NETWORK
8
9
TIP
LOOPI
17
GND
56kΩ
OH
CYG2020
VCC
LINE 1
LINE 2
1
RING
RING R_LIM
470Ω VCC
2
GYRATOR/
CALLER ID
18
17
14
HOOKSWITCH
13
OH
RING
RING
SURGE
DETEC- PROTECTION
TION
R_LIM
8
9
47k
DS-CYG20xx-R02
RING
R_LIM
VCC
18
470Ω GND 17
GYRATOR
VCC
GND
HOOKSWITCH
11
470Ω
1
2
SURGE
PROTECTOR
LINE 1
VCC
1
VCC
RING
www.ixysic.com
11
10
7
8
9
LOOP
CURRENT
R_LIM DETECT
VCC
2.2k
VCC
VCC
SURGE
RING
DETEC- PROTECTION
TION
11
10
RING
TIP
RING
47k
VCC
GND
CID1
CID2
TIP
RING
1
CYG20xx
INTEGRATED CIRCUITS DIVISION
1 Specifications
1.1 Absolute Maximum Ratings @ 25°C
Symbol
Isolation Voltage
Tip/Ring (5, 6) Load Current
(Continuous)
Hook Switch LED Drive Current
Hook Switch LED Reverse Voltage
Ring Detect Phototransistor
Voltage (VCC)
Relative Humidity
(non-condensing)
Operational Temperature
Storage Temperature
Ratings
Units
1000
Vrms
120
mA
50
mA
5
V
20
V
10-85
%
0-70
°C
0-70
°C
Absolute maximum ratings are stress ratings. Stresses in
excess of these ratings can cause permanent damage to
the device. Functional operation of the device at conditions
beyond those indicated in the operational sections of this
data sheet is not implied.
1.2 DC Electrical Characteristics @ 25°C (Unless Otherwise Noted)
Parameter
On-Hook Impedance
Off-Hook Line Leakage Current
Hook Switch Resistance
Off-Hook Supply Current
Conditions
@ 100VDC Across Pins 10 &11 (R, T)
per FCC 68.312
@ 100VDC Across Pins 10 &11 (R, T)
per FCC 68.312
@ VCC = +5V
Minimum
Typical
Maximum
Units
10
-
-
M
-
-
10
A
-
-
15

7
8
9
mA
Hook Switch Power Source, Pin 8
-
4.75
5
20
V
DC Loop Current
-
20
-
120
mA
1.3 AC Signal Path Electrical Characteristics @ 25°C (Unless Otherwise Noted)
Parameter
Conditions
Minimum
Typical
Maximum
Units
300Hz - 3500Hz
18
25
-
dB
Transmit
300Hz - 3500Hz, Test Circuit 1
-
-
7
Receive
300Hz - 3500Hz, Test Circuit 2
-
-
7
300Hz - 3500Hz
-0.25
-
+0.25
60
-
-
40
-
-
-
20
-
120
mA
Return Loss
Insertion Loss
Frequency Response
dB
dB
Longitudinal Balance
On-Hook
Off-Hook
DC Loop Current
Total Harmonic Distortion
Per FCC 68.310
dB
@600Hz and -10dBm
-
-
0.01
%
Secondary Load Impedance
Line 1 and Line 2
-
294
-

Primary Source Impedance
Tip and Ring
-
600
-

R02
www.ixysic.com
2
CYG20xx
INTEGRATED CIRCUITS DIVISION
1.4 Ring Detection Circuit Electrical Characteristics @ 25°C (Unless Otherwise Noted)
Parameter
Conditions
Minimum
Typical
Maximum
Units
Ringing Voltage Detection Range
-
20
-
150
Vrms
Ringing Frequency Detection Range
-
15
-
70
Hz
Ringer Equivalence Number
-
-
0.8B
-
-
@ VCC = +5V
-
-
0.8
-
-
VCC
Ring (Pin 9) Output Voltage (Pulsed)
Logic “0”, Ring Present
Logic “1”, Ring Not Present
V
1.5 Surge, Transient, and Isolation Electrical Characteristics @ 25°C (Unless Otherwise Noted)
Parameter
Conditions
Minimum
Typical
Maximum
Units
Surge Protection Voltage Tip & Ring (Pins 11, 10)
-
-
-
300
V
Transient Voltage Protection on Line 1 and Line 2 (Pins 1, 2)
-
-5
-
+5
V
Per FCC 68.302
-
-
1000
Vrms
Isolation Voltage, Pins (1, 2, 7, 8, 9, 17, 18) to (10, 11, 13, 14)
1.6 Loop Detection (CYG2011) Electrical Characteristics @ 25°C (Unless Otherwise Noted)
Parameter
Loop Current Detection Threshold
Conditions
Minimum
Typical
Maximum
Units
Internal Optocoupler with 2.2k Pull-Up Resistor
-
-
1000
Vrms
1.7 Test Circuits
+5V
VT
+5V
Rm
294Ω
LINE1
VCC
LINE2
GND
LOOP
CID1
CID2
OH
ILOOP
LINE1
VCC
LINE2
GND
10H
+VBATT
ILOOP
CID1
TIP
600Ω
VLR
600Ω
RING
RING
RING
VLT
VT
AC
Source
10H
10H
Transmit Insertion Loss = GTR = 20 Log
10H
CID2
OH
TIP
VLT
RING
VR
Rm
294Ω
+VBATT
Receive Insertion Loss = G RC = 20 Log
-VBATT
VR
V LR
-VBATT
1.8 Caller ID Connections (CYG2020)
Pins 13 & 14 should be connected to a 1-Form-A solid state relay (IXYS IC Division LCA110) as shown here:
VCC
1
μP Control
(Active Low)
6
4
3
CID1
2
www.ixysic.com
CID2
R02
CYG20xx
INTEGRATED CIRCUITS DIVISION
2 Package Pinouts
CYG2020
CYG2000
LINE 1
LINE 2
DO NOT USE
OH
RING
1
2
18
17
7
8
9
11
10
VCC
GND
TIP
RING
LINE 1
LINE 2
OH
RING
1
2
8
9
CYG2011
18
17
VCC
GND
14
13
CID1
CID2
11
10
TIP
RING
LINE 1
LINE 2
1
2
18
17
VCC
GND
LOOPI
OH
RING
7
8
9
11
10
TIP
RING
Top View
Top View
Top View
2.1 CYG20xx Pinouts and Definitions
Pin
I/O
Name
Function
1
I/O
Line 1
Transformer isolated audio signal coupling path for the telephone line.
2
I/O
Line 2
Transformer isolated audio signal coupling path for the telephone line.
7
I
LOOPI
When system is off-hook (OH driven LOW) LOOPI is driven LOW continuously on
CYG2011.
N/C
Keying Pin for CYG2000, do not use.
Driving this pin LOW asserts the off-hook condition. The hook switch LED is current
limited by an internal 470 resistor.
8
I
OH
9
O
RING
Active LOW indicates an incoming ring signal. This is pulsed LOW by the AC ring signal at
the ring frequency from 15-40Hz.
10
I/O
RING
Connection to telephone line Ring conductor.
11
I/O
TIP
13
O
CID2
Caller ID connection on CYG2020. CID1/CID2 connect to an external 1-Form-A solid state
relay (IXYS IC Division LCA110). When the SSR is closed (connecting CID1 to CID2)
Caller ID information is presented to LINE1/LINE2 after the first telephone ring burst.
14
O
CID1
Caller ID connection. See CID2 above.
17
I
GND
Connected to host system ground.
18
I
VCC
Provides power to the hook switch LED. Typically +5V for appx. 8mA LED current. LED is
current limited by an internal 470 resistor. VCC should not exceed 20V.
Connection to telephone line Tip conductor.
3 Typical Application
+5V
CYG2000
294Ω
TX1
LINE 1
18 VCC
VCC
1
10
RING
HYBRID
CIRCUIT
TX2
LINE 2
2
HOOKSWITCH
VCC
RING
DETECT
NETWORK
RX
OH RELAY
GND
RING
OH
RING
8
9
TO TELEPHONE LINE
11
470Ω
TIP
17
56kΩ
R02
SURGE
PROTECTOR
GYRATOR
www.ixysic.com
VCC
GND
4
CYG20xx
INTEGRATED CIRCUITS DIVISION
4 Manufacturing Information
4.1 Handling and Assembly Recommendations
The CYG20xx products are not hermetically sealed, and should not be exposed to any liquid-based rinsing
processes. IXYS Integrated Circuits Division recommends two (2) approaches: (1) the modem should be installed in a
wave-soldering process that uses a no-clean soldering flux that will mostly evaporate during the normal
wave-soldering processes, (2) the modem should be soldered in by hand after the rest of the card is wave-soldered.
4.2 Reflow Profile
These products have a maximum solder temperature as shown below.
Device
Maximum Temperature
CYG2000 / CYG2011 / CYG2020
260°C
4.3 Mechanical Dimensions
4.3.1 CYG2000
1.91
(0.110)
27.18
(1.070)
LINE 1 (PIN 1)
LINE 2
10.16
(0.400)
21.59
(0.850)
+VCC
3.43
(0.135)
GND
17.78
(0.700)
27.18
(1.070)
N/C
0.634 SQ.
(0.25)
TYP.
TIP
OH
RING
RING
3.18
(0.125)
TOP VIEW
5
SIDE VIEW
www.ixysic.com
1.09 DIA.
(0.043)
TYP.
PCB Pattern
(Top View)
2.54
(0.100)
TYP. 8
Dimensions
mm
(inches)
R02
CYG20xx
INTEGRATED CIRCUITS DIVISION
4.3.2 CYG2011
1.91
(0.110)
27.18
(1.070)
10.16
(0.400)
21.59
(0.850)
+VCC
LINE 1 (PIN 1)
LINE 2
3.43
(0.135)
GND
17.78
(0.700)
27.18
(1.070)
LOOPI
0.634 SQ.
(0.25)
TYP.
TIP
OH
RING
RING
1.09 DIA.
(0.043)
TYP.
3.18
(0.125)
TOP VIEW
PCB Pattern
(Top View)
SIDE VIEW
2.54
(0.100)
TYP. 8
Dimensions
mm
(inches)
4.3.3 CYG2020
1.91
(0.110)
27.18
(1.070)
LINE 1 (PIN 1)
LINE 2
10.16
(0.400)
21.59
(0.850)
+VCC
3.43
(0.135)
GND
27.18
(1.070)
17.78
(0.700)
CID1
CID2
0.634 SQ.
(0.25)
TYP.
TIP
OH
RING
RING
1.09 DIA.
(0.043)
TYP.
3.18
(0.125)
TOP VIEW
SIDE VIEW
PCB Pattern
(Top View)
2.54
(0.100)
TYP. 8
Dimensions
mm
(inches)
For additional information please visit our website at: www.ixysic.com
IXYS Integrated Circuits Division makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make
changes to specifications and product descriptions at any time without notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as set forth in IXYS Integrated
Circuits Division’s Standard Terms and Conditions of Sale, IXYS Integrated Circuits Division assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its
products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right.
The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other
applications intended to support or sustain life, or where malfunction of IXYS Integrated Circuits Division’s product may result in direct physical harm, injury, or death to a person or severe
property or environmental damage. IXYS Integrated Circuits Division reserves the right to discontinue or make changes to its products at any time without notice.
Specification: DS-CYG20xx-R02
©Copyright 2012, IXYS Integrated Circuits Division
All rights reserved. Printed in USA.
12/19/2012
R02
www.ixysic.com
6