Product Specification – LED drivers L05060 1-10V dimmable LED Driver 100W Features The L05060 LED Driver is a 100Watt LED driver with adjustable maximum current setting from 350mA to 2800mA. A 1-10V / 100KΩ LOG potentiometer dimming input. A 47KΩ NTC input and a 12Vdc fan output. Extremely low Inrush current of 2x I nominal Specifications System input voltage nominal 115Vac or 240Vac System input voltage range 115-240Vac System input frequency 50/60 Hz Maximum Inrush current 2 x I nominal System input power 240Vac: 110VA Output current 350-2800mA Stabilized adjustable current source. Output voltage range 20Vdc min. - 60Vdc max. Driver efficiency 92% Power factor 0.98 @ 230Vac 0.99 @ 115Vac Nominal line current 240V: 450mA 115V: 690mA Output power 240V: 100 Watt 115V: 60 Watt @ 2A LED voltage versus current Input Voltage 240V Input Voltage 115V 300mA 60V Max. 1667mA Uf 60 Max. 2800mA Uf 35V Max. 300mA Uf 60V Max. 1000mA Uf 60V Max. 2800mA Uf 21V Max. 115Vac: 80VA Dimmer type 1-10V or potentiometer (100K log) Open circuit voltage Max 65Vdc, switching on and off every second. (retry testing if a led is present). Fan voltage/power 12V/ 2.5W NTC sensor specification 47k (example 47K TT4-47KC3H-1-1-500-END , Lumotech part number 072783) Short circuit protection Yes Open circuit protection Yes Overvoltage protection Yes Transformer Thermal protection Yes, against overheating. Load voltage setting time 1 second Output current overshoot No Output isolation Yes, SELV EQ Ambient temperature range (Ta) -25ºC to +50°C Leads primary 0.5mm² – 1.5 mm2 Leads secondary LED connection 0.5mm² – 1.5 mm2 / Other connections 0.2 mm2 – 1.5 mm2 Lead connection method Clamp connector Weight 500 gram Case colour Grey Maximum case temperature (Tc) ≤ 80° C Storage temperature range -20ºC to +50° C Case dimensions 212 x 76 x 46 mm (L x W x H) Complies with standards EN61547, EN55015, EN61000-3-2, EN62384, EN61347-2-13, EN61347-1 Min. current at min. dim level when using the Potentiometer 200 - 300mA www.lumotech.com 1/4 850226_Datasheet L05060_v3 24_07_2012 Product Specification – LED drivers L05060 1-10V dimmable LED Driver 100W Approvals: 1. When the measured NTC temperature is higher than 55°C, the fan output voltage will be switched ON. 2. When the measured NTC temperature is lower than 50°C, the fan output will be switched OFF. 3. When the measured NTC temperature is higher than 70°C, the led output current will be dimmed linear, until the led output is OFF at 80°C. 4. When you want to use the fan continuously without using a temperature sensor, use an 8k2 Ohm resistor instead of the NTC sensor. Technical drawings www.lumotech.com 2/4 850226_Datasheet L05060_v3 24_07_2012 Product Specification – LED drivers L05060 1-10V dimmable LED Driver 100W Powerfactor @ Uout ± 50V 1 0,95 0,9 Power Factor 0,85 0,8 0,75 0,7 0,65 0,6 0,55 0,5 6 11 16 21 26 31 36 41 46 51 56 61 66 71 76 81 86 91 96 Output power (Watt) Power Factor 110V Power Factor 230V Efficiency @ Uout ± 50V 100 95 90 Efficiency (%) 85 80 75 70 65 60 55 50 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 Output power (Watt) efficiency 110V efficiency 230V Efficiency and power factor are measured with a LED voltage of 50V @ 2A www.lumotech.com 3/4 850226_Datasheet L05060_v3 24_07_2012 Product Specification – LED drivers L05060 1-10V dimmable LED Driver 100W Ordering information Article Article number L05060 1-10V dimmable LED Driver 100W / 60V NTC sensor 47K TT4-47KC3H-1-1-500-END L05060 072783 NTC 47K TT4-47KC3H-1-1-500-END 100 90 80 Resistance Ohm 70 60 50 40 30 20 10 0 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 Temperature ºC Disclaimer ©2012, Lumotech Holland B.V. All rights reserved. Designs and specifications may change without prior notice. www.lumotech.com 4/4 850226_Datasheet L05060_v3 24_07_2012