Transient Voltage Suppression Diodes Surface Mount – 3000W > TPSMD series TPSMD Series RoHS Description Uni-directional The TPSMD series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Features • Hi reliability application and automotive grade AEC Q101 qualified • For surface mounted applications in order to optimize board space • Low profile package • Typical failure mode is short from over-specified voltage or current • Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c • IEC-61000-4-2 ESD 15kV(Air), 8kV (Contact) • ESD protection of data lines in accordance with IEC 61000-4-2 (IEC801-2) • EFT protection of data lines in accordance with IEC 61000-4-4 (IEC801-4) • Built-in strain relief • VBR @TJ= VBR@25°C x (1+αT Agency Approvals AGENCY AGENCY FILE NUMBER E230531 Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter Symbol Value Unit Peak Pulse Power Dissipation at TA=25ºC by 10/1000µs Waveform (Fig.2)(Note 1), (Note 2) PPPM 3000 W Power Dissipation on Infinite Heat Sink at TA=50OC PM(AV) 6.5 W Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3) IFSM 300 A Maximum Instantaneous Forward Voltage at 100A for Unidirectional Only VF 3.5 V Operating Junction and Storage Temperature Range x (TJ - 25)) TJ , TSTG -65 to 150 (αT:Temperature Coefficient) °C Typical Thermal Resistance Junction to Lead RuJL 15 °C/W Typical Thermal Resistance Junction to Ambient RuJA 75 °C/W • Glass passivated chip junction Applications Notes: 1. Non-repetitive current pulse , per Fig. 4 and derated above TA = 25OC per Fig. 3. TVS devices are ideal for the protection of I/O Interfaces, VCC bus and other vulnerable circuits used in Telecom, Computer, Industrial and Consumer electronic applications. 2. Mounted on copper pad area of 0.31x0.31” (8.0 x 8.0mm) to each terminal. 3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional device only, duty cycle=4 per minute maximum. Functional Diagram • 3000W peak pulse power capability at 10/1000μs waveform, repetition rate (duty cycles):0.01% • Fast response time: typically less than 1.0ps from 0V to BV min • Excellent clamping capability • Low incremental surge resistance • Typical IR less than 2µA above 12V • High temperature soldering guaranteed: 160°C/10 seconds at terminals • Plastic package has underwriters laboratory flammability 94V-O • Meet MSL level1, per J-STD-020, LF maximun peak of 260°C • Matte tin lead–free plated • Halogen free and RoHS compliant Bi-directional Cathode Anode Uni-directional 1 © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/13/15 Transient Voltage Suppression Diodes Surface Mount – 3000W > TPSMD series Electrical Characteristics Part Number (Uni) Marking Reverse Stand off Voltage VR (Volts) TPSMD10A TPSMD11A TPSMD12A TPSMD13A TPSMD14A TPSMD15A TPSMD16A TPSMD17A TPSMD18A TPSMD20A TPSMD22A TPSMD24A TPSMD26A TPSMD28A TPSMD30A TPSMD33A TPSMD36A TPSMD40A TPSMD43A PDXA PDZA PEEA PEGA PEKA PEMA PEPA PERA PETA PEVA PEXA PEZA PFEA PFGA PFKA PFMA PFPA PFRA PFTA 10.0 11.0 12.0 13.0 14.0 15.0 16.0 17.0 18.0 20.0 22.0 24.0 26.0 28.0 30.0 33.0 36.0 40.0 43.0 © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/13/15 Breakdown Voltage VBR (Volts) @ IT MIN MAX Test Current IT (mA) 11.10 12.20 13.30 14.40 15.60 16.70 17.80 18.90 20.00 22.20 24.40 26.70 28.90 31.10 33.30 36.70 40.00 44.40 47.80 12.30 13.50 14.70 15.90 17.20 18.50 19.70 20.90 22.10 24.50 26.90 29.50 31.90 34.40 36.80 40.60 44.20 49.10 52.80 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 Maximum Clamping Voltage VC @ Ipp (V) Maximum Peak Pulse Current Ipp (A) Maximum Reverse Leakage IR @ VR (µA) 17.0 18.2 19.9 21.5 23.2 24.4 26.0 27.6 29.2 32.4 35.5 38.9 42.1 45.4 48.4 53.3 58.1 64.5 69.4 176.5 164.8 150.8 139.5 129.3 123.0 115.4 108.7 102.7 92.6 84.5 77.1 71.3 66.1 62.0 56.3 51.6 46.5 43.2 5 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 Agency Approval X X X X X X X X X X X X X X X X X X X Transient Voltage Suppression Diodes Surface Mount – 3000W > TPSMD series I-V Curve Characteristics Uni-directional Vc VBR VR V IR VF IT Ipp PPPM VR VBR VC IR VF Peak Pulse Power Dissipation -- Max power dissipation Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT) Clamping Voltage -- Peak voltage measured across the suppressor at a specified Ippm (peak impulse current) Reverse Leakage Current -- Current measured at VR Forward Voltage Drop for Uni-directional Ratings and Characteristic Curves (T =25°C unless otherwise noted) A Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating 1000 PPPM-Peak Pulse Power (KW) Voltage Transients Voltage or Current Voltage Across TVS Current Through TVS 100 10 1 0.31x0.31" (8.0x8.0mm) 0.1 Copper Pad Area 0.001 0.01 0.1 1 td-Pulse Width (ms) 10 Time continues on next page. 3 © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/13/15 Transient Voltage Suppression Diodes Surface Mount – 3000W > TPSMD series Ratings and Characteristic Curves (T =25°C unless otherwise noted) (Continued) A Figure 3 - Peak Pulse Power or Current Derating Curve vs Initial Junction Temperature Figure 4 - Pulse Waveform 150 IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % 100 80 60 40 20 tr=10µsec 0 25 50 75 100 125 150 Peak Value IPPM 100 Half Value IPPM IPPM ( ) 2 50 0 0 TJ=25°C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM 175 10/1000µsec. Waveform as defined by R.E.A td 1.0 0 2.0 3.0 4.0 t-Time (ms) TA-Ambient temperature (ºC) Figure 5 - Typical Junction Capacitance Figure 6 - Steady State Power Derating Curve 100000 PM(AV), Steady Sate Power Dissipation (W) Cj (pF) 10000 Uni-directional V= OV 1000 Uni-directional @ VR 100 10 1 1.0 10.0 100.0 1000.0 VBR - Reverse Breakdown Voltage (V) IFSM - Peak Forward Surge Current (A) 350 300 250 200 150 100 50 0 10 100 Number of Cycles at 60 Hz © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/13/15 0 25 50 75 100 125 TA - Ambient Temperature(ºC) Figure 7 - Maximum Non-Repetitive Peak Forward Surge Current Uni-Directional only 1 6.5 6 5.5 5 4.5 4 3.5 3 2.5 2 1.5 1 0.5 0 4 150 175 Transient Voltage Suppression Diodes Surface Mount – 3000W > TPSMD series Soldering Parameters Pre Heat Lead–free assembly - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 120 secs Average ramp up rate (Liquidus Temp (TL) to peak 3°C/second max TS(max) to TL - Ramp-up Rate 3°C/second max Reflow - Temperature (TL) (Liquidus) 217°C - Time (min to max) (ts) 60 – 150 seconds Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 30 seconds max Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (TP) 8 minutes max. Do not exceed 280°C tp TP Ramp-up TL Temperature (T) Reflow Condition tL Critical Zone TL to TP Ts(max) Ramp-down Ts(min) ts Preheat 25˚C t 25˚C to Peak Time (t) Environmental Specifications Physical Specifications High Temp. Storage JESD22-A103 HTRB JESD22-A108 Weight 0.007 ounce, 0.21 grams Temperature Cycling JESD22-A104 Case JEDEC DO214AB. Molded plastic body over glass passivated junction MSL JEDEC-J-STD-020, Level 1 Polarity Color band denotes positive end (cathode) except Bidirectional. H3TRB JESD22-A101 Terminal Matte Tin-plated leads, Solderable per JESD22-B102 RSH JESD22-B106 Dimensions DO-214AB (SMC J-Bend) Dimensions Cathode Band C A B H D E F G Dimensions in K inches and L (millimeters) J I Solder Pads (all dimensions in mm) 5 Inches Min Millimeters Max Min Max 3.200 A 0.114 0.126 2.900 B 0.260 0.280 6.600 7.110 C 0.220 0.245 5.590 6.220 D 0.079 0.103 2.060 2.620 E 0.030 0.060 0.760 1.520 F - 0.008 - 0.203 G 0.305 0.320 7.750 8.130 H 0.006 0.012 0.152 0.305 I 0.129 - 3.300 - 2.400 J 0.094 - K - 0.165 L 0.094 - 4.200 2.400 - © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/13/15 Transient Voltage Suppression Diodes Surface Mount – 3000W > TPSMD series Part Numbering System Part Marking System TPSMD XXX A F Cathode Band 5% VBR VOLTAGE TOLERANCE XXXX VR VOLTAGE YMXXX SERIES Littelfuse Logo Marking Code Trace Code Marking Y:Year Code M: Month Code XXX: Lot Code Packaging Options Part number Component Package TPSMDxxxX DO-214AB 3000 Tape & Reel - 16mm tape/13” reel EIA STD RS-481 TPSMDxxxX-T7 DO-214AB 500 Tape & Reel – 16mm tape /7” reel EIA STD RS-481 Packaging Option Quantity Packaging Specification Tape and Reel Specification 0.157 (4.0) 0.63 (16.0) Cathode 0.315 (8.0) Optional 7” 7.0 (187) 13” 13.0 (330) 0.80 (20.2) Arbor Hole Dia. 0.65 (16.4) © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/13/15 0.059 DIA (1.5) Cover tape Dimensions are in inches (and millimeters). Direction of Feed 6