HA17393A Series Dual Comparators REJ03D0677-0300 Rev.3.00 Mar 10, 2006 Description The HA17393A series products are comparators designed for general purpose, especially for power control systems. These ICs operate from a single power-supply voltage over a wide range of voltages, and feature a reduced powersupply current since the supply current is independent of the supply voltage. These comparators have the merit which ground is included in the common-mode input voltage range at a singlevoltage power supply operation. These products have a wide range of applications, including limit comparators, simple A/D converters, pulse/square-wave/time delay generators, wide range VCO circuits, MOS clock timers, multivibrators, and high-voltage logic gates. Features • • • • • • • Wide power-supply voltage range : 2 to 36 V Very low supply current : 0.8 mA Typ. Low input bias current : 25 nA Typ. Low input offset current : 3 nA Typ. Low input offset voltage : 2 mV Typ. The common-mode input voltage range includes ground Output voltages compatible with CMOS logic systems Rev.3.00 Mar 10, 2006 page 1 of 8 HA17393A Series • Low electro-magnetic susceptibility Measurement Condition Vcc 1k 1k Vin 1V + − 5.0 5.1 kΩ 4.0 Vout 0.01 µF Vout (V) Vcc = 5 V HA17393A Vout vs. Vin 6.0 −10 dBm RF signal source (for quasi-RF noise) 3.0 2.0 1.0 HA17393A (0 Hz) HA17393A (10 MHz) HA17393A (100 MHz) 0.0 −1.0 0.85 0.90 0.95 1.00 Vin (V) 1.05 1.10 1.15 HA17393 Vout vs. Vin 6.0 5.0 Vout (V) 4.0 3.0 2.0 1.0 HA17393 (0 Hz) HA17393 (10 MHz) HA17393 (100 MHz) 0.0 −1.0 0.85 0.90 0.95 1.00 Vin (V) 1.05 1.10 1.15 Ordering Information Type No. HA17393A HA17393AF HA17393ARP HA17393AT Application Commercial use Rev.3.00 Mar 10, 2006 page 2 of 8 Package Name DIP-8 pin SOP-8 pin (JEITA) SOP-8 pin (JEDEC) TSSOP-8 pin Package Code PRDP0008AF-B PRSP0008DE-B PRSP0008DD-C PTSP0008JC-B HA17393A Series Pin Arrangement Vout1 Vin(−)1 1 2 Vin(+)1 3 GND 4 1 − + 2 + − 8 VCC 7 Vout2 6 Vin(−)2 5 Vin(+)2 (Top view) Circuit Schematic (1/2) VCC Q3 Q2 Vin(+) Q4 Q1 Vout Q8 Vin(−) Q7 Q5 Q6 Note: If Input/Output terminals voltage over the absolute maximum ratings, there is possibility of mis-operation, characteristics deterioration and destruction, because of the current’s flowing to parasitic diode in IC. The Input/Output terminals are recommended to be protected with the clamp circuit which using the diode with low forward voltage (like schottky barrier diode) when there is a possibility for the Input/Output terminals voltage exceeds the absolute maximum ratings. Rev.3.00 Mar 10, 2006 page 3 of 8 HA17393A Series Absolute Maximum Ratings (Ta = 25°C) Item Power supply voltage Differential input voltage Input voltage Output pin voltage Output short current Allowable power dissipation Symbol DIP SOP TSSOP Operating temperature Storage temperature VCC Vin(diff) Vin Vout Ios *1 PT Topr Tstg Ratings 36 ±VCC −0.3 to +VCC −0.3 to +36 constant 570 *2 385 *3 192 *4 −40 to +85 −55 to +125 Unit V V V V mW °C °C Notes: 1. Short circuit between the output and VCC will be a cause to destory the circuit. The maximum output current is about 20 mA for any supply voltage. 2. HA17393A: These are the allowable values up to Ta = 55°C. Derate by 8.3mW/°C above that temperature. 3. HA17393AF/ARP: These are the allowable values up to Ta = 25°C mounting in air. When it is mounted on glass epoxy board of 40 mm × 40 mm × 1.5 mmt with 30% wiring density, the allowable value is 570 mW up to Ta = 45°C. If Ta > 45°C, derate by 7.14 mW/°C. 4. HA17393AT: These are the allowable values up to Ta = 25°C. Derate by 1.92 mW/°C above that temperature. Electrical Characteristics (VCC = 5 V, Ta = 25°C) Item Input offset voltage *1 Input offset current Input bias current *2 Common mode input voltage *3 Symbol Min Typ Max Unit Test Conditions VIO 2 5 mV IIO 3 50 nA IIN (+) − IIN (−) IIB 25 250 nA IIN (+) or IIN (−) + VCM 3.5 V VCM− 0 V Supply current ICC 0.8 2.0 mA All comparators: RL = ∞, All channels on 5 Voltage gain * AVD (200) V/mV VCC = 15V, RL ≥ 15kΩ Response time *4,5 tR (1.3) µs VRL = 5V, RL = 5.1kΩ 5 Large signal response time * tRI (300) ns VIN = TTL Threshold width, VREF = 1.4V Output sink current IO(sink) 6 16 mA VIN (−) ≥ 1V, VIN (+) = 0, VO ≤ 1.5V Output saturation voltage VO(sat) 400 mV VIN (−) ≥ 1V, VIN (+) = 0, Iosink = 4mA Output leak current *5 ILO (0.1) nA VIN (−) = 0, VIN (+) ≥ 1V, VO = 5V Notes: 1. VREF = 1.4 V and RS = 50 Ω, when VO = 1.4 V at output switching point. 2. Under linear operation. 3. Common mode input voltage or each one of the input signal should not be less than −0.3 V. 4. This is a value to 100 mV input step voltage with 5 mV over drive. 5. Design spec. Rev.3.00 Mar 10, 2006 page 4 of 8 HA17393A Series Characteristic Curves Supply Current vs. Ambient Temperature Output Sink Current vs. Ambient Temperature 20 1.0 VC C = 36 Output Sink Current Iosink (mA) Supply Current ICC (mA) 1.25 V 15 V 0.75 5V 2V 0.5 0.25 0 −20 0 25 50 5V 10 2V 5 0 −20 0 25 50 75 Ambient Temperature Ta (°C) Ambient Temperature Ta (°C) Output Sink Current vs. Output Voltage Output Saturation Voltage vs. Ambient Temperature 20 V CC = Output Saturation Voltage VO(sat) (mV) Output Sink Current Iosink (mA) 15 V 75 25 36 V 15 V 5V 15 2V 10 5 0 VCC = 36 V 15 0 10 20 30 Output Voltage VO (V) Rev.3.00 Mar 10, 2006 page 5 of 8 40 400 300 200 100 VCC = 2 V 0 −20 0 5V 15 V 25 36 V 50 Ambient Temperature Ta (°C) 75 HA17393A Series Voltage Gain vs. Ambient Temperature Input Offset Voltage vs. Ambient Temperature 110 4 100 Input Offset Voltage VIO (mV) Voltage Gain AV (dB) VCC = 15 V 5V 36 V 2V 90 80 70 −20 0 25 50 VCC = 36 V 15 V 2 5V 0 2V −2 −4 −20 75 50 75 Response Time vs. Ambient Temperature Input Bias Current vs. Ambient Temperature 4 80 60 VCC = 36 V 15 V 5V 40 Response Time tR (µs) Input Bias Current IIB (nA) 25 Ambient Temperature Ta (°C) Ambient Temperature Ta (°C) 2V 20 10 0 −20 0 0 25 50 Ambient Temperature Ta (°C) Rev.3.00 Mar 10, 2006 page 6 of 8 75 3 2 VCC = 2 V 5V 1 15 V 36 V 0 −20 0 25 50 Ambient Temperature Ta (°C) 75 HA17393A Series Package Dimensions JEITA Package Code P-DIP8-6.3x9.6-2.54 RENESAS Code PRDP0008AF-B Previous Code DP-8FV MASS[Typ.] 0.54g D 5 E 8 1 4 b3 0.89 A Z A1 Reference Dimension in Millimeters Symbol Min L e1 D E A A1 bp b3 c θ e Z L θ bp e c e1 ( Ni/Pd/Au plating ) JEITA Package Code P-SOP8-4.4x4.85-1.27 RENESAS Code PRSP0008DE-B *1 Previous Code FP-8DGV 0.5 0.40 0.48 0.56 1.30 0.19 0.25 0.31 15° 0° 2.29 2.54 2.79 1.27 2.54 MASS[Typ.] 0.1g F D 8 Nom Max 7.62 9.60 10.6 6.30 7.4 5.06 NOTE) 1. DIMENSIONS"*1 (Nom)"AND"*2" DO NOT INCLUDE MOLD FLASH. 2. DIMENSION"*3"DOES NOT INCLUDE TRIM OFFSET. 5 c *2 E HE bp Index mark Terminal cross section ( Ni/Pd/Au plating ) 1 Z Reference Dimension in Millimeters Symbol 4 e *3 bp x M A L1 A1 θ L y Detail F Rev.3.00 Mar 10, 2006 page 7 of 8 D E A2 A1 A bp b1 c c1 θ HE e x y Z L L1 Min Nom Max 4.85 5.25 4.4 0.00 0.1 0.35 0.4 0.20 2.03 0.45 0.15 0.20 0.25 0° 6.35 8° 6.5 6.75 1.27 0.12 0.15 0.75 0.42 0.60 0.85 1.05 HA17393A Series JEITA Package Code P-SOP8-3.95x4.9-1.27 RENESAS Code PRSP0008DD-C *1 Previous Code FP-8DCV MASS[Typ.] 0.085g F D 8 NOTE) 1. DIMENSIONS"*1 (Nom)"AND"*2" DO NOT INCLUDE MOLD FLASH. 2. DIMENSION"*3"DOES NOT INCLUDE TRIM OFFSET. 5 c *2 E HE bp Index mark Terminal cross section ( Ni/Pd/Au plating ) 1 Reference Dimension in Millimeters Symbol 4 *3 e Z bp x M A L1 A1 θ L y Detail F JEITA Package Code P-TSSOP8-4.4x3-0.65 RENESAS Code PTSP0008JC-B *1 Previous Code TTP-8DAV Min Nom Max 4.90 5.30 3.95 0.10 0.14 0.25 1.75 0.34 0.40 0.46 0.15 0.20 0.25 0° 8° 5.80 6.10 6.20 1.27 0.25 0.10 0.75 0.40 0.60 1.27 1.08 MASS[Typ.] 0.034g D 8 D E A2 A1 A bp b1 c c1 θ HE e x y Z L L1 F 5 NOTE) 1. DIMENSIONS"*1 (Nom)"AND"*2" DO NOT INCLUDE MOLD FLASH. 2. DIMENSION"*3"DOES NOT INCLUDE TRIM OFFSET. c HE *2 E bp Terminal cross section ( Ni/Pd/Au plating ) Reference Dimension in Millimeters Symbol Index mark L1 1 *3 bp x M θ A1 A Z 4 e L Detail F y Rev.3.00 Mar 10, 2006 page 8 of 8 D E A2 A1 A bp b1 c c1 θ HE e x y Z L L1 Min Nom Max 3.00 3.30 4.40 0.03 0.07 0.10 1.10 0.15 0.20 0.25 0.10 0.15 0.20 0° 8° 6.20 6.40 6.60 0.65 0.13 0.10 0.805 0.40 0.50 0.60 1.00 Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan Keep safety first in your circuit designs! 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap. Notes regarding these materials 1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party. 2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials. 3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product information before purchasing a product listed herein. The information described here may contain technical inaccuracies or typographical errors. Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor home page (http://www.renesas.com). 4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes no responsibility for any damage, liability or other loss resulting from the information contained herein. 5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. 6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials. 7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. 8. Please contact Renesas Technology Corp. for further details on these materials or the products contained therein. http://www.renesas.com RENESAS SALES OFFICES Refer to "http://www.renesas.com/en/network" for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501 Renesas Technology Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K. Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900 Renesas Technology (Shanghai) Co., Ltd. Unit 204, 205, AZIACenter, No.1233 Lujiazui Ring Rd, Pudong District, Shanghai, China 200120 Tel: <86> (21) 5877-1818, Fax: <86> (21) 6887-7898 Renesas Technology Hong Kong Ltd. 7th Floor, North Tower, World Finance Centre, Harbour City, 1 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: <852> 2265-6688, Fax: <852> 2730-6071 Renesas Technology Taiwan Co., Ltd. 10th Floor, No.99, Fushing North Road, Taipei, Taiwan Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999 Renesas Technology Singapore Pte. Ltd. 1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632 Tel: <65> 6213-0200, Fax: <65> 6278-8001 Renesas Technology Korea Co., Ltd. Kukje Center Bldg. 18th Fl., 191, 2-ka, Hangang-ro, Yongsan-ku, Seoul 140-702, Korea Tel: <82> (2) 796-3115, Fax: <82> (2) 796-2145 Renesas Technology Malaysia Sdn. Bhd Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No.18, Jalan Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia Tel: <603> 7955-9390, Fax: <603> 7955-9510 © 2006. Renesas Technology Corp., All rights reserved. Printed in Japan. Colophon .6.0