Teccor® brand Thyristors 0.8 Amp Sensitive SCRs EC103xx & SxSx Series RoHS Description Excellent unidirectional switches for phase control applications such as heating and motor speed controls. Sensitive gate SCRs are easily triggered with microAmps of current as furnished by sense coils, proximity switches, and microprocessors. Features & Benefits • RoHS compliant • Voltage capability up to 600 V • Glass – passivated junctions Main Features • Surge capability up to 20 A Applications Symbol IT(RMS) VDRM /VRRM IGT Value Unit 0.8 A 400 to 600 V 12 to 500 μA Typical applications are capacitive discharge systems for strobe lights and gas engine ignition. Also controls for power tools, home/brown goods and white goods appliances. Additional Information Schematic Symbol A K Datasheet Samples Resources G Absolute Maximum Ratings — Sensitive SCRs Parameter Test Conditions Value Unit IT(RMS) Symbol RMS on-state current TC = 75°C 0.8 A IT(AV) Average on-state current TC = 75°C 0.51 A single half cycle; f = 50Hz; TJ (initial) = 25°C 16 single half cycle; f = 60Hz; TJ (initial) = 25°C 20 I2t Value for fusing tp = 8.3 ms 1.6 A2s Critical rate of rise of on-state current f = 60 Hz ; TJ = 110°C 50 A/μs Peak gate current TJ = 110°C 1 A Average gate power dissipation TJ = 110°C 0.1 W Storage temperature range -40 to 150 °C Operating junction temperature range -40 to 110 °C ITSM I 2t di/dt IGM PG(AV) Tstg TJ Peak non-repetitive surge current A © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/14/14 Teccor® brand Thyristors 0.8 Amp Sensitive SCRs Electrical Characteristics (TJ = 25°C, unless otherwise specified) Value Symbol IGT VGT Test Conditions MAX. VD = 6V; RL = 100 Ω SxS1 EC103X1 SxS2 EC103X2 SxS / 2N6565 EC103X SxS3 EC103X3 Unit 12 50 200 500 µA MAX. 400V dv/dt VD = VDRM; RGK = 1kΩ VGD VD = VDRM; RL = 3.3 kΩ; TJ = 110°C MIN. IH IT = 20mA (initial), RGK = 1kΩ MAX. tq (1) MAX. tgt IG = 2 x IGT; PW = 15µs; IT = 1.6A 600V MIN. TYP. 0.8 V 20 25 30 40 10 10 15 20 0.2 V/μs 0.25 V 5 60 2 5 8 mA 50 45 μs 20 30 μs (1) IT=1A; tp=50µs; dv/dt=5V/µs; di/dt=-5A/µs Static Characteristics Symbol Test Conditions IT = 1.2A; tp = 380 µs VTM Value Unit 1.7 V MAX. TJ = 25°C IDRM / IRRM VDRM = VRRM RGK = 1kΩ 1 TJ = 100°C 50 MAX. TJ = 110°C μA 100 Thermal Resistances Symbol Parameter Rθ(J-C) Junction to case (AC) Rθ(J-A) Junction to ambient Notes: x = voltage, y = sensitivity * = Mounted on 1 cm2 copper (two-ounce) foil surface © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/14/14 Value EC103xy/2N6565 75 SxSy 60* EC103xy/2N6565 160 Unit °C/W °C/W Teccor® brand Thyristors 0.8 Amp Sensitive SCRs Figure 1: Normalized DC Gate Trigger Current vs. Junction Temperature Figure 2: Normalized DC Gate Trigger Voltage vs. Junction Temperature 2.0 Ratio of VGT / VGT (TJ = 25ºC) Ratio of IGT/IGT (TJ = 25°C) 4.0 3.0 2.0 1.0 1.5 1.0 0.5 0.0 0.0 -40 -15 10 35 60 85 -40 110 -15 10 Junction Temperature (TJ) -- (°C) Figure 3: Normalized DC Holding Current vs. Junction Temperature 85 110 10 Instantaneous On-state Current (iT) – Amps 2.5 Ratio of IH / IH (TJ = 25°C) 60 Figure 4: O n-State Current vs. On-State Voltage (Typical) 3.0 2.0 1.5 1.0 0.5 0.0 -40 -15 10 35 60 85 110 TJ = 25°C 8 6 4 2 0 0.7 0.8 Junction Temperature (TJ) -- (°C) 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 Instantaneous On-state Voltage (vT) – Volts Figure 5: Power Dissipation (Typical) vs. RMS On-State Current Figure 6: M aximum Allowable Case Temperature vs. RMS On-State Current 0.7 115 Maximum Allowable Case Temperature (TC) - °C Average On-State Power Dissipation [PD(AV)] - (Watts) 35 Junction Temperature (TJ) -- (°C) 0.6 105 0.5 95 0.4 0.3 85 0.2 75 0.1 65 0.0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 RMS On-State Current [IT(RMS)] - Amps 0.7 0.8 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 RMS On-State Current [IT(RMS)] - Amps © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/14/14 Teccor® brand Thyristors 0.8 Amp Sensitive SCRs Figure 7: Maximum Allowable Case Temperature vs. Average On-State Current Figure 8: Maximum Allowable Ambient Temperature vs. RMS On-State Current 120 Maximum Allowable Ambient Temperature (TA) - °C Maximum Allowable Case Temperature (TC) - °C 115 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° FREE AIR RATING 100 105 80 95 60 85 40 75 65 20 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° 0.0 0.1 0.2 0.3 0.4 0.5 0 0.6 0.0 0.1 0.2 Average On-State Current [IT(AVE)] - Amps Figure 9: Maximum Allowable Ambient Temperature vs. Average On-State Current 80 60 40 20 0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 Average On-State Current [IT(AVE)] - Amps Figure 11: Peak Repetitive Sinusoidal Pulse Current 180 160 140 120 1 Hz 100 80 12 Hz 60 ITM 40 60 Hz 20 tW 1 10 Pulse Current Duration (tW) - μs © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/14/14 100 Peak Discharge Current (ITM) -Amps Maximum Allowable Ambient Temperature (TA) - °C 0.5 0.6 0.7 0.8 0.9 1.0 180 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° FREE AIR RATING 100 Peak Discharge Current (ITM) - Amps 0.4 Figure 10: Peak Capacitor Discharge Current 120 0 0.3 RMS On-State Current [IT(RMS)] - Amps 160 140 1 Hz 120 12 Hz 100 60 Hz 80 60 ITRM 40 20 tW 0 1 10 Pulse Current Duration (tW) - μs 100 Teccor® brand Thyristors 0.8 Amp Sensitive SCRs Figure 12: Surge Peak On-State Current vs. Number of Cycles Peak Surge (Non-repetitive) On-state Current (ITSM) – Amps 100.0 SUPPLY FREQUENCY: 60 Hz Sinusoidal LOAD: Resistive RMS On-State Current: [IT(RMS)]: Maximum Rated Value at Specified Case Temperature Notes: 1. G ate control may be lost during and immediately following surge current interval. 2. Overload may not be repeated until junction temperature has returned to steady-state rated value. 10.0 1.0 0.1 1 10 100 1000 Surge Current Duration -- Full Cycles Figure 13: Simple Test Circuit for Gate Trigger Voltage and Current Note: V1 — 0 V to 10 V dc meter VGT — 0 V to 1 V dc meter IG — 0 mA to 1 mA dc milliammeter R1 — 1 k potentiometer Reset Normally-closed Pushbutton 100 + 6VDC D.U.T. IGT – V1 1k (1%) IN4001 IG 100 VGT R1 To measure gate trigger voltage and current, raise gate voltage (VGT) until meter reading V1 drops from 6 V to 1 V. Gate trigger voltage is the reading on VGT just prior to V1 dropping. Gate trigger current IGT Can be computed from the relationship VGT IGT = IG- ____ Amps 1000 where IG is reading (in amperes) on meter just prior to V1 dropping Note: IGT may turn out to be a negative quantity (trigger current flows out from gate lead). If negative current occurs, IGT value is not a valid reading. Remove 1 k resistor and use IG as the more correct IGT value. This will occur on 12 µA gate products. © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/14/14 Teccor® brand Thyristors 0.8 Amp Sensitive SCRs Soldering Parameters Pb – Free assembly Pre Heat - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus Temp) (TL) to peak 5°C/second max TS(max) to TL - Ramp-up Rate 5°C/second max Reflow - Temperature (TL) (Liquidus) 217°C - Temperature (tL) 60 – 150 seconds Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 5°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 280°C Physical Specifications Terminal Finish 100% Matte Tin-plated/Pb-free Solder Dipped Body Material UL recognized epoxy meeting flammability classification 94V-0 Lead Material Copper Alloy tP TP Temperature Reflow Condition Ramp-up TL tL TS(max) Preheat TS(min) 25 tS time to peak temperature Time Environmental Specifications Test AC Blocking Temperature Cycling Temperature/ Humidity Design Considerations High Temp Storage Careful selection of the correct device for the application’s operating parameters and environment will go a long way toward extending the operating life of the Thyristor. Good design practice should limit the maximum continuous current through the main terminals to 75% of the device rating. Other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. Overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. Correct mounting, soldering, and forming of the leads also help protect against component damage. Low-Temp Storage © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/14/14 Ramp-do Ramp-down Thermal Shock Autoclave Specifications and Conditions MIL-STD-750, M-1040, Cond A Applied Peak AC voltage @ 110°C for 1008 hours MIL-STD-750, M-1051, 100 cycles; -40°C to +150°C; 15-min dwell-time EIA / JEDEC, JESD22-A101 1008 hours; 320V - DC: 85°C; 85% rel humidity MIL-STD-750, M-1031, 1008 hours; 150°C 1008 hours; -40°C MIL-STD-750, M-1056 10 cycles; 0°C to 100°C; 5-min dwelltime at each temperature; 10 sec (max) transfer time between temperature EIA / JEDEC, JESD22-A102 168 hours (121°C at 2 ATMs) and 100% R/H Resistance to Solder Heat MIL-STD-750 Method 2031 Solderability ANSI/J-STD-002, category 3, Test A Lead Bend MIL-STD-750, M-2036 Cond E Teccor® brand Thyristors 0.8 Amp Sensitive SCRs Dimensions – TO-92 (E Package) TC Measuring Point A B Cathode Anode Gate E Millimeters Min Max Min Max A 0.176 0.196 4.47 4.98 B 0.500 - 12.70 - D 0.095 0.105 2.41 2.67 E 0.150 - 3.81 - F 0.046 0.054 1.16 1.37 G 0.135 0.145 3.43 3.68 H 0.088 0.096 2.23 2.44 J 0.176 0.186 4.47 4.73 K 0.088 0.096 2.23 2.44 L 0.013 0.019 0.33 0.48 M 0.013 0.017 0.33 0.43 All leads insulated from case. Case is electrically nonconductive. G H M Inches Dimension F L D K J Dimensions — Compak (C Package) TC / TL Temperature Measurement Point Gate B D M A N P C Cathode Anode H F L E J 0.079 (2.0) K 0.079 (2.0) G 0.079 (2.0) 0.040 (1.0) 0.030 (0.76) 0.110 (2.8) Pad Outline Dimensions are in inches (and millimeters). Dimension A Inches Millimeters Min Max Min Max 0.130 0.156 3.30 3.95 B 0.201 0.220 5.10 5.60 C 0.077 0.087 1.95 2.20 D 0.159 0.181 4.05 4.60 E 0.030 0.063 0.75 1.60 F 0.075 0.096 1.90 2.45 G 0.002 0.008 0.05 0.20 H 0.077 0.104 1.95 2.65 J 0.043 0.053 1.09 1.35 K 0.006 0.016 0.15 0.41 L 0.030 0.055 0.76 1.40 M 0.022 0.028 0.56 0.71 N 0.027 0.033 0.69 0.84 P 0.052 0.058 1.32 1.47 © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/14/14 Teccor® brand Thyristors 0.8 Amp Sensitive SCRs Product Selector Voltage Part Number Gate Sensitivity Type X 12μA Sensitive SCR TO-92 X 50μA Sensitive SCR TO-92 400V 600V EC103 x 1 X EC103 x 2 X EC103 x 800V 1000V Package X / 2N6565 X 200μA Sensitive SCR TO-92 EC103 x 3 X X 500μA Sensitive SCR TO-92 S x S1 X X 12μA Sensitive SCR Compak S x S2 X X 50μA Sensitive SCR Compak SxS X X 200μA Sensitive SCR Compak S x S3 X X 500μA Sensitive SCR Compak Note: x = Voltage Packing Options Part Number Marking Weight EC103xy / 2N6565 Packing Mode Base Quantity EC103xy / 2N6565 0.19 g Bulk 2000 EC103xyRP EC103xy 0.19 g Reel Pack 2000 EC103xyAP EC103xy 0.19 g Ammo Pack 2000 SxSy 0.08 g Embossed Carrier 2500 SxSyRP Note: x = Voltage, y = sensitivity TO-92 (3-lead) Reel Pack (RP) Radial Leaded Specifications Meets all EIA-468-C Standards 1.6 (41.0) 0.236 (6.0) 0.708 (18.0) 0.02 (0.5) 0.098 (2.5) MAX 1.26 (32.0) 0.354 (9.0) 0.5 (12.7) 0.1 (2.54) Cathode 0.2 (5.08) Anode Gate 0.157 DIA (4.0) 14.17(360.0) Flat up 1.97 (50.0) Direction of Feed © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/14/14 Dimensions are in inches (and millimeters). Teccor® brand Thyristors 0.8 Amp Sensitive SCRs TO-92 (3-lead) Ammo Pack (AP) Radial Leaded Specifications Meets all EIA-468-C Standards 0.236 (6.0) 1.62 (41.2) 0.708 (18.0) 0.02 (0.5) 0.098 (2.5) MAX 1.27 (32.2) 0.354 (9.0) n Directio 0.157 (4.0) DIA Anode Cathode 0.2 (5.08) Gate 0.1 (2.54) 0.5 (12.7) Flat down of Feed 25 Devices per fold 1.85 (47.0) 12.2 (310.0) 1.85 (47.0) Dimensions are in inches (and millimeters). 13.3 (338.0) Compak Embossed Carrier Reel Pack (RP) Specifications Meets all EIA-481-1 Standards 0.157 (4.0) 0.47 (12.0) Anode 0.36 (9.2) 8.0 0.315 (8.0) 0.512 (13.0) Arbor Hole Dia. Cathode Gate 0.059 DIA (1.5) 12.99 (330.0) Cover tape Dimensions are in inches (and millimeters). 0.49 (12.4) Direction of Feed © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/14/14 Teccor® brand Thyristors 0.8 Amp Sensitive SCRs Part Numbering System (TO-92) Part Marking System EC 103 D 1 75 TO-92 (E Package) EC103D1 DEVICE TYPE EC: TO-92 SCR 2N: JEDEC Lead Form Dimensions xx: Lead Form Option YMLXX ® CURRENT RATING 103: 0.8A (TO-92) SENSITIVITY & TYPE 1: 12 µ A 2: 50 µ A [blank]: 200 µ A 3: 500 µ A VOLTAGE RATING D: 400V M: 600V (JEDEC) 6565: 400V Part Numbering System (Compak) S 6 VOLTAGE RATING 4: 400V 6: 600V Compak (C Package) SENSITIVITY & TYPE 1: 12 µ A 2: 50 µ A [blank]: 200 µ A 3: 500 µ A S6S1 ® YMXXX Date Code Marking CURRENT RATING S: 0.8A (Compak) © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/14/14 Y:Year Code M: Month Code L: Location Code XX: Lot Serial Code Part Marking System (Compak) S 1 DEVICE TYPE S: Compak SCR Date Code Marking Y:Year Code M: Month Code XXX: Lot Trace Code