MAX4736 0.6Ω, Low-Voltage, Single-Supply, Dual SPDT

EVALUATION KIT AVAILABLE
MAX4736
0.6Ω, Low-Voltage, Single-Supply, Dual SPDT
Analog Switch
General Description
Features
The MAX4736 is a low on-resistance, low-voltage, dual
single-pole/double throw (SPDT) analog switch that operates from a single 1.6V to 4.2V supply. This device has
fast switching speeds (tON = 25ns, tOFF = 20ns max),
handles rail-to-rail analog signals, and consumes less
than 4μW of quiescent power. The MAX4736 has breakbefore-make switching.
●● Low RON
0.6Ω (3V Supply)
1.5Ω (1.8V Supply)
●● 0.1Ω max RON Flatness (3V Supply)
●● Single-Supply Operation Down to 1.6V
●● Available in TQFN, QFN, μDFN, and μMAX
Packages
When powered from a 3V supply, the MAX4736 features
low 0.6Ω on-resistance (RON), with 0.1Ω RON matching
and 0.05Ω RON flatness. The digital logic input is 1.8V
CMOS compatible when using a single 3V supply.
●● 1.8V CMOS Logic Compatible (3V Supply)
●● Fast Switching: tON = 25ns, tOFF = 20ns
Ordering Information
The MAX4736 has one normally open (NO) switch and
one normally closed (NC) switch, and is available in
12-pin TQFN-EP (3mm x 3mm), QFN-EP (3mm x 3mm),
10-pin μMAX and 10 pin μDFN (2mm x 2mm) packages.
PART
Applications
●●
●●
●●
●●
●●
●●
●●
●●
●●
Power Routing
Battery-Powered Systems
Audio and Video Signal Routing
Low-Voltage Data-Acquisition Systems
Communications Circuits
PCMCIA Cards
Cellular Phones
Modems
Hard Drives
PIN-PACKAGE
PKG CODE
MAX4736EUB+
10 μMAX
U10+2
MAX4736ETC+
12 TQFN-EP*
T1233+1
MAX4736EGC+
12 QFN-EP*
G1233+1
MAX4736ELB+
10 μDFN
L1022+1
Note: All devices operate over the -40°C to +55°C operating
temperature range.
*EP = Exposed pad.
+Denotes lead(Pb)-free/RoHS-compliant package.
Pin Configurations/Functional Diagrams/Truth Table
TOP VIEW
IN1
12
NO1
1
GND
2
NO2
3
COM1 N.C.
11
10
MAX4736
4
5
IN2
COM2 N.C.
TQFN/QFN
19-2382; Rev 3; 1/14
6
9
NC1
8
V+
7
NC2
10 COM1
IN1 1
9 NC1
NO1
2
GND
3
NO2
4
7 NC2
IN2
5
6 COM2
MAX4736
µMAX/µDFN
8 V+
IN_
0
1
MAX4736
NO_
OFF
ON
NC_
ON
OFF
SWITCHES SHOWN
FOR LOGIC 0 INPUT
NOTE: CONNECT EXPOSED PAD ON
TQFN, QFN, AND µDFN TO GND.
MAX4736
0.6Ω, Low-Voltage, Single-Supply, Dual SPDT
Analog Switch
Absolute Maximum Ratings
(Voltages referenced to GND.)
V+, IN_...................................................................-0.3V to +4.6V
COM_, NO_, NC_ (Note 1) ...........................-0.3V to (V+ + 0.3V)
Continuous Current COM_, NO_, NC_ ...........................±300mA
Continuous Current (all other pins)....................................±20mA
Peak Current COM_, NO_, NC_
(pulsed at 1ms 10% duty cycle)...................................±500mA
Continuous Power Dissipation (TA = +70°C)
10-Pin μDFN (derate 5.3mW/°C above +70°C)........423.7mW
10-Pin μMAX (derate 5.6mW/°C above +70°C)...........444mW
12-Pin TQFN-EP (derate 14.7mW/°C above +70°C)...... 1176mW
12-Pin QFN-EP (derate 11.9mW/°C above +70°C)....... 952mW
Operating Temperature Range.............................-40°C to +85°C
Maximum Junction Temperature.......................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s)...................................+300°C
Note 1: Signals on COM_, NO_, or NC_ exceeding V+ or GND are clamped by internal diodes. Limit forward current to maximum
current rating.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Electrical Characteristics—Single 3V Supply
(V+ = 2.7V to 4.2V, VIH = 1.4V, VIL = 0.5V, TA = TMIN to TMAX, unless otherwise specified. Typical values are at V+ = 3.0V,
TA = +25°C.) (Notes 2, 3)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
V+
V
ANALOG SWITCH
Analog Signal Range
On-Resistance (Note 4)
On-Resistance Match
Between Channels
(Notes 4, 5)
VCOM_,
VNO_,
VNC_
0
RON
V+ = 2.7V ,
ICOM_ = 100mA;
VNO_ or VNC_ = 1.5V
ΔRON
V+ = 2.7V ,
ICOM_ = 100mA;
VNO_ or VNC_ = 1.5V
On-Resistance Flatness
(Note 6)
RFLAT(ON)
V+ = 2.7V,
ICOM_ = 100m A;
VNO_ or VNC_ = 1V, 1.5V, 2V
NO_ or NC_ Off-Leakage
Current (Note 10)
INO_ (OFF),
INC_ (OFF)
V+ = 3.6V ,
VCOM_ = 0.3V, 3.3V;
VNO_ or VNC_ = 3.3V, 0.3V
ICOM_(ON)
V+ = 3.6V,
VCOM_ = 0.3V, 3.3V;
VNO_ or VNC_ = 0.3V, 3.3V,
or floating
COM_ On-Leakage
Current (Note 10)
www.maximintegrated.com
+25°C
0.6
TMIN to TMAX
0.8
1
+25°C
0.1
TMIN to TMAX
0.3
+25°C
0.05
TMIN to TMAX
0.2
+25°C
-1
TMIN to TMAX
-5
+25°C
-2
TMIN to TMAX
-10
±0.002
0.2
0.1
+1
+5
±0.002
Ω
Ω
Ω
nA
+2
nA
+10
Maxim Integrated │ 2
MAX4736
0.6Ω, Low-Voltage, Single-Supply, Dual SPDT
Analog Switch
Electrical Characteristics—Single 3V Supply (continued)
(V+ = 2.7V to 4.2V, VIH = 1.4V, VIL = 0.5V, TA = TMIN to TMAX, unless otherwise specified. Typical values are at V+ = 3.0V,
TA = +25°C.) (Notes 2, 3)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
20
25
UNITS
SWITCH DYNAMIC CHARACTERISTICS
Turn-On Time
tON
VNO_, VNC_ = 1.5V;
RL = 50Ω, CL = 35pF,
Figure 1
Turn-Off Time
tOFF
VNO_, VNC_ = 1.5V;
RL = 50Ω, CL = 35pF,
Figure 1
Break-Before-Make
(Note 7)
tBBM
VNO_, VNC_ = 1.5V;
RL = 50Ω, CL = 35pF,
Figure 2
Charge Injection
Q
VGEN = 0, RGEN = 0,
CL = 1.0nF, Figure 3
+25°C
60
pC
NO_ or NC_ OffCapacitance
COFF
f = 1MHz, Figure 4
+25°C
33
pF
COM_ Off-Capacitance
CCOM(OFF)
f = 1MHz, Figure 4
+25°C
60
pF
COM_ On-Capacitance
CCOM(ON)
f = 1MHz, Figure 4
+25°C
85
pF
130
MHz
+25°C
TMIN to TMAX
30
+25°C
15
TMIN to TMAX
25
+25°C
TMIN to TMAX
20
5
ns
ns
ns
1
-3dB On-Channel
Bandwidth
BW
Signal = 0, RIN = ROUT =
50Ω, CL = 5pF, Figure 5
Off-Isolation (Note 8)
VISO
f = 1MHz, VCOM_ = 1VP-P,
RL = 50Ω, CL = 5pF, Figure 5
+25°C
-52
dB
Crosstalk (Note 9)
VCT
f = 1MHz, VCOM_ = 1VP-P ,
RL = 50Ω, CL = 5pF, Figure 5
+25°C
-78
dB
Total Harmonic Distortion
THD
f = 20Hz to 20kHz, VCOM_ =
2VP-P, RL = 32Ω
+25°C
0.018
%
LOGIC INPUT (A_, IN_)
Input Logic High
VIH
Input Logic Low
VIL
Input Leakage Current
IIN
1.4
VIN_ = 0 or 3.6V
-1
V
+0.005
0.5
V
+1
µA
3.6
V
1
µA
POWER SUPPLY
Power-Supply Range
V+
Positive Supply Current
I+
www.maximintegrated.com
1.6
V+ = 3.6V, VIN_ = 0 or V+,
all channels on or off
0.006
Maxim Integrated │ 3
MAX4736
0.6Ω, Low-Voltage, Single-Supply, Dual SPDT
Analog Switch
Electrical Characteristics—Single 1.8V Supply
(V+ = 1.8V, VIH = 1.0V, VIL = 0.4V, TA = TMIN to TMAX, unless otherwise specified. Typical values are at TA = +25°C.) (Notes 2, 3)
PARAMETER
SYMBOL
CONDITIONS
TA
MIN
TYP
MAX
UNITS
V+
V
ANALOG SWITCH
Analog Signal Range
On-Resistance
VCOM_,
VNO_,
VNC_
RON
0
ICOM_ = 100mA;
VNO_ or VNC_ = 1V
+25°C
1.5
TMIN to TMAX
2
3
Ω
SWITCH DYNAMIC CHARACTERISTICS
Turn-On Time
tON
VNO, or VNC_ = 1V;
RL = 50Ω, CL = 35pF,
Figure 1
Turn-Off Time
tOFF
VNO, or VNC_ = 1V;
RL = 50Ω, CL = 35pF,
Figure 1
Break-Before-Make
(Note 7)
tBBM
VNO, or VNC_ = 1V;
RL = 50Ω, CL = 35pF,
Figure 2
Q
VGEN = 0, RGEN = 0,
CL = 1nF, Figure 3
+25°C
35
pC
Charge Injection
+25°C
25
TMIN to TMAX
35
+25°C
18
TMIN to TMAX
25
28
+25°C
TMIN to TMAX
30
7
ns
ns
ns
1
Off-Isolation (Note 8)
VISO
f = 1MHz, VNO_ = VNC_
= 1VP-P, RL = 50Ω,
CL = 5pF, Figure 5
+25°C
-52
dB
Crosstalk (Note 9)
VCT
f = 1MHz, VCOM_ = 1VP-P ,
RL = 50Ω, CL = 5pF, Figure 5
+25°C
-78
dB
LOGIC INPUT (IN_)
Input Logic High
VIH
Input Logic Low
VIL
Input Leakage Current
IIN
1
VIN_ = 0 or 3.6V
V
0.4
V
1
µA
Note 2: The algebraic convention, where the most negative value is a minimum and the most positive value is a maximum, is used
in this data sheet.
Note 3: -40°C specifications are guaranteed by design.
Note 4: RON and ΔRON matching specifications for TQFN/QFN packaged parts are guaranteed by design.
Note 5: ΔRON = RON(MAX) - RON(MIN).
Note 6: Flatness is defined as the difference between the maximum and the minimum value of on-resistance as measured over the
specified analog signal ranges.
Note 7: Guaranteed by design.
Note 8: Off-Isolation = 20log10(VCOM_/ VNO_), VCOM_ = output, VNO_ = input to OFF switch.
Note 9: Between two switches.
Note 10:Leakage parameters are 100% tested at hot temperature and guaranteed by correlation at room.
Note 11:Devices are guaranteed to 1 million cycles of operation. (Cycle = switch on → switch off → switch on)
Note 12:The minimum load resistance is 8Ω.
www.maximintegrated.com
Maxim Integrated │ 4
MAX4736
0.6Ω, Low-Voltage, Single-Supply, Dual SPDT
Analog Switch
Typical Operating Characteristics
(TA = +25°C, unless otherwise noted.)
RON (Ω)
V+ = 1.8V
V+ = 2.5V
1.0
V+ = 3.0V
V+ = 3.0V, TA = +85°C
1.2
1.0
0.8
0
1
2
3
0
4
1.0
ON, V+ = 1.8V
10
OFF, V+ = 1.8V
V+ = 3.0V, TA = +25°C
1.5
2.0
2.5
1
3.0
-40
-15
10
35
60
TEMPERATURE (°C)
CHARGE INJECTION vs. VCOM
SUPPLY CURRENT vs. SUPPLY
VOLTAGE AND TEMPERATURE
LOGIC-LEVEL THRESHOLD
vs. SUPPLY VOLTAGE
V+ = 3.0V
20
V+ = 1.8V
-10
0.5
1.0
2.0
1.5
2.5
10
TA = +25°C
1
TA = -40°C
0.1
0.6
0
MAX4736 toc07
tOFF
20
5
5
2.4
2.8
SUPPLY VOLTAGE (V)
3.2
3.6
MAX4736 toc06
2.4
2.8
3.2
3.6
tOFF, V+ = 1.8V
tON, V+ = 3.0V
15
10
www.maximintegrated.com
2.0
tON, V+ = 1.8V
25
10
2.0
1.6
TURN-ON/OFF TIMES
vs. TEMPERATURE
30
tON
20
1.6
0.5
FALLING
SUPPLY VOLTAGE (V)
tON/tOFF (ns)
tON/tOFF (ns)
0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2 3.6
RISING
0.8
SUPPLY VOLTAGE (V)
25
0
0.9
0.001
TURN-ON/OFF TIME
vs. SUPPLY VOLTAGE
15
1.0
0.7
VCOM (V)
30
1.1
0.01
0.0001
3.0
TA = +85°C
THRESHOLD (V)
SUPPLY CURRENT (nA)
100
1.2
85
0
MAX4736 toc08
1000
MAX4736 toc04
30
0
0.5
100
VCOM (V)
40
0
0
ON, V+ = 3.0V
OFF, V+ = 3.0V
VCOM (V)
50
10
V+ = 3.0V, TA = -40°C
1000
MAX4736 toc03
V+ = 1.8V, TA = +85°C
0.2
V+ = 3.6V
60
Q (pC)
1.4
0.4
70
-20
V+ = 1.8V, TA = +25°C
0.6
0.5
0
1.6
ON/OFF-LEAKAGE CURRENT
vs. TEMPERATURE
10,000
MAX4736 toc05
RON (Ω)
1.5
V+ = 1.8V, TA = -40°C
1.8
LEAKAGE CURRENT (pA)
V+ = 1.6V
2.0
2.0
MAX4736 toc01
2.5
ON-RESISTANCE
vs. VCOM AND TEMPERATURE
MAX4736 toc02
ON-RESISTANCE vs. VCOM
tOFF, V+ = 3.0V
-40
-15
10
35
60
85
TEMPERATURE (°C)
Maxim Integrated │ 5
MAX4736
0.6Ω, Low-Voltage, Single-Supply, Dual SPDT
Analog Switch
Typical Operating Characteristics (continued)
(TA = +25°C, unless otherwise noted.)
0
ON-RESPONSE
-15
RL = 32Ω
0.08
V+ = 1.8V
VCOM = 1.2VP-P
OFF-ISOLATION
-30
CROSSTALK
-45
THD (%)
LOSS (dB)
0.10
MAX4736 toc09
15
TOTAL HARMONIC DISTORTION
vs. FREQUENCY
-60
-75
-90
MAX4736 toc10
FREQUENCY RESPONSE
0.06
0.04
V+ = 3.0V
VCOM = 2VP-P
0.02
-105
-120
0.1
0.01
1
10
100
1000
0
10
100
FREQUENCY (MHz)
1k
10k
100k
FREQUENCY (Hz)
Pin Description
PIN
NAME
FUNCTION
μMAX/μDFN
TQFN/QFN
1
12
IN1
Digital Control Input Switch 1
2
1
NO1
Analog Switch 1—Normally Open Terminal
3
2
GND
Ground
4
3
NO2
Analog Switch 2—Normally Open Terminal
5
4
IN2
Digital Control Input Switch 2
6
5
COM2
7
7
NC2
8
8
V+
9
9
NC1
10
11
COM1
—
6,10
N.C.
—
EP
EP
www.maximintegrated.com
Analog Switch 2—Common Terminal
Analog Switch 2—Normally Closed Terminal
Positive-Supply Voltage Input
Analog Switch 1—Normally Closed Terminal
Analog Switch 1—Common Terminal
No Connection
Exposed Pad. Connect to ground.
Maxim Integrated │ 6
MAX4736
0.6Ω, Low-Voltage, Single-Supply, Dual SPDT
Analog Switch
Detailed Description
Logic Inputs
The MAX4736 is a low 0.8Ω max (at V+ = 2.7V) onresistance, low-voltage, dual SPDT analog switch that operates from a 1.6V to 4.2V single supply. CMOS switch
construction allows switching analog signals that range
from GND to V+.
The MAX4736 logic inputs can be driven up to 3.6V,
regardless of the supply voltage. For example, with a 1.8V
supply, IN_ can be driven low to GND and high to 3.6V.
Driving IN_ rail-to-rail minimizes power consumption.
When powered from a 2.7V supply, the 0.8Ω max RON
allows high continuous currents to be switched in a variety
of applications.
Analog signals that range over the entire supply voltage
(V+ to GND) can be passed with very little change in
onresistance (see Typical Operating Characteristics). The
switches are bidirectional, so the NO_, NC_, and COM_
pins can be used as either inputs or outputs.
Applications Information
Proper power-supply sequencing is recommended for all
CMOS devices. Do not exceed the absolute maximum
ratings; stresses beyond the listed ratings can cause permanent damage to the devices. Always sequence V+ on
first, followed by NO_, NC_, or COM_.
Although it is not required, power-supply bypassing
improves noise margin and prevents switching noise
propagation from the V+ supply to other components. A
0.1μF capacitor, connected from V+ to GND, is adequate
for most applications.
Analog Signal Levels
Layout
High-speed switches require proper layout and design
procedures for optimum performance. Reduce stray inductance and capacitance by keeping traces short and wide.
Ensure that bypass capacitors are as close to the device
as possible. Use large ground planes where possible.
Test Circuits/Timing Diagrams
MAX4736
V+
LOGIC
INPUT
V+
VIN
NC_ or NO_
NO_ or NC_
LOGIC
INPUT
0
50%
VOUT
COM_
RL
IN_
t r < 5ns
t f < 5ns
VIN_ = VIH + 0.5V
GND
CL INCLUDES FIXTURE AND STRAY CAPACITANCE.
t OFF
CL
VOUT
SWITCH
OUTPUT
0
0.9 x V0UT
0.9 x VOUT
t ON
LOGIC INPUT WAVEFORMS INVERTED FOR SWITCHES
THAT HAVE THE OPPOSITE LOGIC SENSE.
Figure 1. Switching Time
www.maximintegrated.com
Maxim Integrated │ 7
MAX4736
0.6Ω, Low-Voltage, Single-Supply, Dual SPDT
Analog Switch
Test Circuits/Timing Diagrams (continued)
MAX4736
V+
LOGIC
INPUT
V+
NC_ or NO_
VIN
VOUT
COM_
NO_ or NC_
LOGIC
INPUT
VIH + 0.5V
50%
0
CL
RL
IN_
t r < 5ns
t f < 5ns
GND
0.9 x VOUT
VOUT
tD
CL INCLUDES FIXTURE AND STRAY CAPACITANCE.
Figure 2. Break-Before-Make Interval
MAX4736
V+
∆VOUT
V+
RGEN
NC_
VOUT
COM_
VOUT
OR NO_
V GEN
CL
GND
IN
OFF
ON
IN
IN
VINL TO VINH
ON
OFF
OFF
OFF
Q = (∆V OUT )(C L )
IN DEPENDS ON SWITCH CONFIGURATION;
INPUT POLARITY DETERMINED BY SENSE OF SWITCH.
Figure 3. Charge Injection
10nF
Chip Information
V+
TRANSISTOR COUNT: 379
PROCESS: CMOS
V+
COM_
CAPACITANCE
METER
f = 1MHz
MAX4736
IN_
NC_ OR
NO_
VINL
OR
VINH
GND
Figure 4. Channel Off/On-Capacitance
www.maximintegrated.com
Maxim Integrated │ 8
MAX4736
0.6Ω, Low-Voltage, Single-Supply, Dual SPDT
Analog Switch
V+ 10nF
NETWORK
ANALYZER
0 OR V+
V+
IN_
NC_
50Ω
VIN
COM_
50Ω
MAX4736
VOUT
NO
50Ω
GND
MEAS
50Ω
REF
OFF-ISOLATION = 20log
VOUT
VREF
ON-LOSS = 20log
VOUT
VREF
CROSSTALK = 20log
VOUT
VREF
50Ω
MEASUREMENTS ARE STANDARDIZED AGAINST SHORTS AT IC TERMINALS.
OFF-ISOLATION IS MEASURED BETWEEN COM_ AND "OFF" NO_ OR NC_ TERMINAL ON EACH SWITCH.
ON-LOSS IS MEASURED BETWEEN COM_ AND "ON" NO_ OR NC_ TERMINAL ON EACH SWITCH.
CROSSTALK IS MEASURED FROM ONE CHANNEL TO ALL OTHER CHANNELS.
SIGNAL DIRECTION THROUGH SWITCH IS REVERSED; WORST VALUES ARE RECORDED.
Figure 5. On-Loss, Off-Isolation, and Crosstalk
Package Information
For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a “+”,
“#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing
pertains to the package regardless of RoHS status.
PACKAGE TYPE
PACKAGE CODE
OUTLINE NO.
LAND PATTERN NO.
10 µMAX
U10+2
21-0061
90-0330
12 TQFN
T1233+1
21-0136
90-0066
12 QFN
G1233+1
21-0102
90-0215
10 µDFN
L1022+1
21-0164
90-0006
www.maximintegrated.com
Maxim Integrated │ 9
MAX4736
0.6Ω, Low-Voltage, Single-Supply, Dual SPDT
Analog Switch
Revision History
REVISION
NUMBER
REVISION
DATE
3
1/14
DESCRIPTION
Added QFN package
PAGES
CHANGED
1, 2, 4, 6, 10
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at www.maximintegrated.com.
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses
are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits)
shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.
© 2014 Maxim Integrated Products, Inc. │ 10