HPF5761

Differential PECL Crystal Clock Oscillators
3HPF5761 Series
+3.3V “F” family
PECL Outputs
MERCURY
Since 1973
3HPF5761 features 0.4 ps typical phase jitter and
low phase noise (-132 dBc at 10 KHz for 155.520 MHz).
Differential PECL Outputs meet the requirements for
SONET, XDSL and other communication protocols.
General Specifications
Product Series
Frequency Range
Output Logic
3HPF5761; “F” family characteristics. Tri-State on pad 1
38 MHz ~ 640 MHz.
Differential PECL 100 K square wave
Commercial “ C ”::
Industrial “ I ”:
Stability Code
-10°C to +70°C
-40°C to +85°C
±25 ppm
A
D
±50 ppm
B
E
±100 ppm
C
F
Custom ±xx ppm
Cxx
Ixx
If custom, use “temperature range code + desired ppm stability” for the stability
code. Example: “C20” (±20 ppm over -10 to +70°C) or “I35”.
Frequency Stability
vs Operating Temperature
Range
vs Supply Voltage Change
vs Load Change
±3 ppm max.with ±10% supply voltage change
±2 ppm max.with ±10% Load change:
Supply Voltage VCC
+3.3 V ± 10 %
Output Voltage HIGH “1”, VOH
2.275 V min.; 2.420 V max. Condition: 50 ohms to VDD-2V
Output Voltage LOW “0”, VOL
1.490 V min..; 1.680 V max. Condition: 50 ohms to VDD-2V
38 MHz≤ fout ≤ 100 MHz: 70 mA max.
100 MHz< fout ≤ 320 MHz: 85 mA max
320 MHz< fout ≤ 640 MHz: 95 mA max
50 ohms into VCC-2V or Thevenin equivalent (terminating resistors required on all
outputs).
fout < 150 MHz: 0.5 ns typical; 0.7 ns max.
150 MHz ≤ fout ≤ 320 MHz: 0.4 ns. typical; 0.55 ns. max
f320 MHz < fout ≤ 640 MHz: 0.3 ns. typical; 0.45 ns. max
Measured at 20% ↔ 80% of the wave form.
50% ± 5% max. measured at 50% waveform
3HPF5761: Tri-State is on pad 1. Pad 2 is no connection.
3HPF5762: Tri-State is on pad 2. Pad 1 is no connection.
Differential PECL and complimentary PECL outputs.
Both outputs are disabled (high impedance) when pad No. 2 is taken
below 0.45*Vcc referenced to ground (threshold). Oscillator is always
ON. Only buffer stage is disabled.
Disable current: 50 uA max. (at 0.0 V).
Disable time: 10 ns max.
At disabled mode, both outputs are enabled when pad No. 2 is taken
above 0.45*Vcc referenced to ground (threshold).
Enable time: 10ns+one period of the output frequency max.
0.5 ps max. (12 KHz to 20 MHz integrated)
10 Hz
100 Hz
1 kHz
10 kHz
100 kHz
1 MHz
10 MHz
Current Consumption
Load
Rise Time (Tr) and
Fall Time (Tf)
Duty Cycle
No Connection
Tri-state
Function on
pad No. 1
Disable
Enable
Phase Jitter (RMS)
Offset
SSB Phase
MERCURY
www.mercury-crystal.com
Taiwan: TEL (886)-2-2406-2779, FAX (886)-2-2496-0769, e-mail: [email protected]
U.S.A.: TEL (1)-909-466-0427, FAX (1)-909-466-0762, e-mail: [email protected]
MERCURY
Page 1 of 4
Date: April 1, 2008
Rev. 1
Differential PECL Crystal Clock Oscillators
3HPF5761 Series
+3.3V “F” family
Noise (dBc/Hz)
-65
-66
-62
-59
-49
MERCURY
Since 1973
Start-up Time
-96
-124
-96
-122
-92
-120
-85
-117
-84
-111
Period Jitter
(RMS)
2.5 ps typ; 4.0 ps max
3.0 ps typ; 5.0 ps max
3.0 ps typ; 5.0 ps max
3.0 ps typ; 5.0 ps max
6.0 ps typ; 8.0 ps max
5 m sec. max.
Aging
±3 ppm / year max.
Packaging
179 mm reel; 16 mm tape, 8.0 mm pitch. 1000 pcs per reel.
Contact Pad Surface Finish
Gold over nickel on ceramic substrate
Jitter
77.760 MHz
106.250 MHz
155.520 MHz
311.020 MHz
622.080 MHz
PECL Outputs
77.760 MHz
106.250 MHz
155.520 MHz
311.020 MHz
622.080 MHz
-136
-132
-132
-126
-132
-128
-128
-125
-120
-118
Period Jitter
(peak-to-peak)
18 ps typ.; 30 ps max
20 ps typ.; 30 ps max
20 ps typ.; 30 ps max
25 ps typ.; 30 ps max
40 ps typ.; 50 ps max
-145
-149
-144
-150
-144
-150
-139
-148
-128
-138
Integrated Jitter RMS
(12 KHz ~20 MHz)
0.4 ps typ; 0.5 ps max.
0.4 ps typ; 0.5 ps max.
0.4 ps typ; 0.5 ps max.
0.4 ps typ; 0.5 ps max.
0.4 ps typ; 0.5 ps max.
(1)
Inclusive of 25°C tolerance, operating temperature range, ±10% input voltage variation, load change, aging at +25°C, shock and
vibration.
Absolute Maximum Rating Permanent damage may be created if operate beyond limits specified
+4.6 V D.C. max.
Vss-0.5V min.; VDD +0.5V max.
Vss-0.5V min.; VDD +0.5V max.
2 KV max. Human body model
Supply Voltage VDD
Input Voltage Vi
Input Voltage Vo
E S D Protection
Environmental Performance Specifications
Green Requirement
Moisture Sensitivity Level
Storage temp. range
Humidity
Hermetic seal
Solderability
Vibration
Shock
RoHS Compliant and Pb (lead) free
Level 1
-55 to +125°C
85% RH, 85°C, 48 hours
Leak rate 2x10-8 ATM-cm3/sec max.
MIL-STD-202F method 208E
MIL-STD-202F method 204, 35G, 50 to 2000 Hz
MIL-STD-202F method 213B, test condi. E, 1000GG ½ sine wave
Part Number Format and Example:
Example: 3HPF5761A-155.520
Explanation: +3.3V HPF576 series PECL output clock oscillator, 155.520 MHz, frequency stability is ±25 ppm over
0°C to +70°C, frequency deviation range is ±100 ppm minimum.
": customer to specify
"
"
3
HPF5761
—
A
—
155.520
n
o
p
q
n: Voltage codes: “3” for +3.3 V; o: HPF5761 product series. ‘H” for clock; “P” for PECL; “F”: for “F” family
performance.“576” for 5x7 mm SMD with 6 pads. ‘1” for Tri-State on pad 1.
p: Frequency stability code: “A” ~ “F” or custom. See table above. q: Frequency in MHz
MERCURY
Page 2 of 4
Date: April 1, 2008
Rev. 1
Differential PECL Crystal Clock Oscillators
3HPF5761 Series
+3.3V “F” family
PECL Outputs
MERCURY
Since 1973
3HPF5761 Test Circuit and Waveform:
+3.3 V
+3.3 V
A
3HPF5761
+
1.30 V
50 ohms
-
0.1uF
1
2
PECL
Duty Cycle
Duty Cycle
45% ~ 55%
45% ~ 55%
80%
50%
20%
MEC
+
V
3
82.5
ohms
-
5 4
127
ohms
6
82.5
ohms
PECL
Supply
Voltage
127
ohms
PECL
1.30 V
50 ohms
PECL
Tr
Top view
Tf
Duty
80
50
20
MERCURY
Page 3 of 4
Date: April 1, 2008
Rev. 1
Differential PECL Crystal Clock Oscillators
3HPF5761 Series
+3.3V “F” family
3HPF5761
0.7 [0.028]
1.8 max.
[0.071 max.]
3
Pad 1 Tri-state
Pad 4 PECL Output
Pad 2 No Connection Pad 5 PECL Output
Pad 3 Ground
Pad 6 Supply Voltage
2.0[0.079]
2
1
[0.004]
0.1
MEC
Rounded pad is pad No. 1
2.54[0.100]
Since 1973
unit mm[inches]
[0.055]
1.4
4
5
6
3
2
1
5.08 [0.200]
typical
bottom view
1.5[0.059]
1.8[0.071]
0.6[0.024]
[0.050]
1.27
[0.197± 0.006]
5.00± 0.15
[0.275± 0.006]
7.00± 0.15
5
6
4
MERCURY
R0
.7
3HPF5761 Package Dimensions and Recommended Pad Layout:
PECL Outputs
Top view
5.08 [0.200]
3HPF576 Recommended Solder Reflow Profile
Topside temperature of board to be 260°C min. and 270°C max.
Temperature ( °C)
260
250
240
Peak Temperature: 260°C max. and 10 sec. max.
Time within 5°C of actual peak: 20 to 40 sec. max.
Liquidus Temperature
t
Ram
up a x.
p
m
a
6°C p dow
Ra ec m
n
/se
s
20~40
sec.
/
c m at
3°C
ax.
200
150
Flux Activation
Temperature
100
50
Pre-heat 1
30
MERCURY
60
90
Soaking temp: 140°C~225°C
Soaking time: 60~120 sec.
Soaking Zone
Pre-heat 2
120 150 180
Page 4 of 4
Reflow
Zone
30~60 sec.
210 240 270 300 330
Date: April 1, 2008
Cooling
Time
(sec)
Rev. 1