“X42” series • • • 4.0x2.5x0.6mm Surface Mount Crystals MERCURY Since 1973 Gold-plated ceramic base with metal lid seam welded package Extremely low aging. Specifically designed for hand-held communication equipment, PDAs, GPS and Bluetooth. High shock and vibration resistance. SPECIFICATIONS Crystal Holder Prefix n: X42 series Frequency Range o: 12.0 ~50.0 MHz AT-cut Fundamental mode Calibration Tolerance : q ±5 ppm (±0.0005 %), or±10 ppm (±0.001 %), or ±30 ppm (±0.003 %) at 25°C Frequency Stability : r ±5 ppm (±0.0005 %); or ±10 ppm (±0.001 %) ;or ±30 ppm (±0.003 %) Operatin g Temperature Range s –20°C to +70°C. or –30°C to +85°C Shunt Capacitance (Co): 2.0~4.0 pF typical, 5 pF maximum Equivalent Series Resistance: (E.S.R.) t Load Capacitance (CL ) p : Frequency Vibration Mode E.S.R. max. 12.0~20.0 AT fundamental 80 Ω 20.01~50.0 AT fundamental 60 Ω Series (S) Parallel: Please specify CL value, typical CL ranges from 10 to 32pF) Drive Level: 100 μW max. Aging: Less than ±3 ppm per year at +25°C Reflow Soldering: 10 seconds maximum at +260°C two times or 180 seconds at 230°C one time Note: Tighter tolerance, tighter stability and lower ESR are available. MERCURY www.mercury-crystal.com Taiwan: TEL (886)-2-2406-2779, FAX (886)-2-2496-0769, e-mail: [email protected] U.S.A.: TEL (1)-909-466-0427, FAX (1)-909-466-0762, e-mail: [email protected] MERCURY Page 1 of 4 Date: May 1, 2006 Rev. 1 “X42” series 4.0x2.5x0.6 mm MERCURY Surface Mount Crystals Since 1973 STANDARD FREQUENCIES AND PART NUMBERS (partial frequency list only. Frequency tolerance, frequency stability and ESR can be specified per your requirements). MEC Part Number MEC Specification Code MEC Part Number MEC Specification Code X42-12.800-12P X42-13.000-16P X42-14.318-18P X42-16.000-16P X42-16.384-16P X42-18.432-16P X42-19.200-16P X42-20.000-20P X42-22.2184-10P X42-24.000-10P X42-24.576-10P X42-25.000-10P 20/20/-20+70/80R 20/20/-20+70/80R 20/20/-20+70/80R 20/20/-20+70/80R 20/20/-20+70/80R 20/20/-20+70/80R 20/20/-20+70/80R 20/20/-20+70/80R 20/20/-20+70/60R 20/20/-20+70/60R 20/20/-20+70/60R 20/20/-20+70/60R X42-27.000-10P X42-28.375-10P X42-28.63636-10P X42-29.4912-10P X42-30.000-10P X42-32.000-10P X42-32.768-10P X42-33.000-10P X42-35.2512-S X42-40.000-10P X42-44.000-S X42-48.000-S 20/20/-20+70/60R 20/20/-20+70/60R 20/20/-20+70/60R 20/20/-20+70/60R 20/20/-20+70/60R 20/20/-20+70/60R 20/20/-20+70/60R 20/20/-20+70/60R 20/20/-20+70/60R 20/20/-20+70/60R 20/20/-20+70/60R 20/20/-20+70/60R ENVIRONMENTAL AND MECHANICAL SPECIFICATIONS Green Requirement RoHS compliant and Pb (lead free) Storage Temperature -40°C to +85°C Gross Leak 1 Kg Pressurized water immersion test per Mercury internal procedures Fine Leak < 5 x10-8 atm cc /sec by helium leak check Shock ±5 ppm max. Free drop 3 times from 75 cm height onto a hard wooden board or half sine wave acceleration of 100G peak amplitude for 11 m. sec. duration, 3 cycles each plane. Vibration ±5 ppm max. Frequency:10 to 55 Hz, amplitude: 1.5 mm or 10 Gs rms. Duration: 6 hours. Solderability MIL-STD-883, Method 2003 Humidity After 48 hours at 85°C, 85% relative humidity non-condensing Thermal Shock Temperature cycling: Exposed at -40°C for 30 minutes then to +85°C for 30 minutes for duration of 5 days Marking Permanency MIL-STD-202, Method 215. Laser engraved. Insulation Resistance 500 MΩ min. at 100 V±15 V DC MERCURY Page 2 of 4 Date: May 1, 2006 Rev. 1 “X42” series 4.0x2.5x0.6 mm MERCURY Surface Mount Crystals Since 1973 HOW TO ORDER: Complete Part Number = Mercury part number + Mercury spec. code. "= Please specify Example: X42-16.000-16P-20/20/-20+70/580R-option Explanation: X42 series crystal, 16.000 MHz, 16 pF load capacitance, ±20 ppm frequency tolerance, ±20 ppm frequency stability over -20 to +70°C, ESR is 80 ohms max. " " " " " " " 16P — 20 X42− 16.000 — / 20 / -20+70 / 80R n o p q r s t n: Crystal package prefix o: Frequency in MHz p: Load Capacitance (Use “S” for series; use “_ _P” for parallel load capacitance) q: Frequency Tolerance at +25°C r: Frequency stability over operating temperature range s: Operating temperature range t: ESR (Equivalent Series Resistance in ohms) max. PACKAGE DIMENSIONS AND SUGGESTED PAD LAYOUT Unit: mm [inches] 2.0¡ Ó 0.1 4.0¡ Ó 0.1 3 0.7¡ Ó 0.1 4 3 0.4 4 bottom view 0.6¡ Ó 0.1 1.0 typ. 2 1.2 4 3.0 1.6 1 2 1 2 0.9 typ. 2 2.5¡ Ó 0.1 1 1. Pad No. 1 and pad No. 3 are connected 4 through the metal lid for grounding. 1.4 2. Chamfered pad is pad No. 1. 3. Count clockwise when looking at top view. 4. Count counter-clockwise when looking at bottom view. MERCURY Page 3 of 4 Date: May 1, 2006 top view 3 Rev. 1 “X42” series 4.0x2.5x0.6 mm Surface Mount Crystals MERCURY Since 1973 RECOMMENDED REFLOW SOLDERING PROFILE: TAPE AND REEL SPEC.: MERCURY 1000 pcs per reel. Page 4 of 4 unit: mm Date: May 1, 2006 Rev. 1